My Samsung Focus can't quite stop playing the plugged in/charging sound when it's not plugged in and charging. This is highly annoying and battery draining, the only fix for the noise would be to turn it to vibrate only, but the device still wakes up (and the battery icon shows that it is charging)
This is the strangest thing ever, is this a known issue with this phone?
Any help would be appreciated, thank you!
Yes
Known issue, covered in many forums and threads. There is not just one solution. Please search here and do a google search.
Possibly a water damage issue, I really highly doubt it's software related.
I'm gonna try ricing it.
Suggested
Check the connectors and make sure there is no debris in either one. Make sure the pins are not bent and touching the side of the connector. Do you have the latest OS and firmware level? Pull the battery and leave it out for a couple minutes. There are many other suggestions. The solution for you could be one of many.
I had the same problem. The centre metal tang in the charging port is too close to the edge. By bending it away from the closest wall, the beeping will stop.
Related
As of last night my A500 will not charge. I left the device overnight and unfortunately now have Zero charge.
- My charger makes a noise, I think it always did, so I'm assuming the charger is OK.
Can anyone confirm that the chargers give off a kind of electrical buzz when working?
- I get no light at all on my A500. If the charger is OK I'm thinking something has gone within the tab, be that circuit or battery.
Any ideas or tips here?
- Sadly I do not have a multi-meter to test either the charger or the tab, no friends with a similar device, I've lost my proof or purchase (which is painful and rules out warranty), and am a bit stuck what to do.
Any ideas?
- I've heard/read that allowing the power to drop too low can cause a problem. Obviously Zero is bad in this case.
Can anyone confirm this rumour or suggest a fix?
- I did try entering recovery and resetting the battery stats - whether this made things worse or not is unclear - it certainly did not help.
ANY HELP OR IDEAS WELCOME (bear in mind that I have spent quite some time searching and trying other peoples' ideas already though.
Thanks,
ta-wan said:
As of last night my A500 will not charge. I left the device overnight and unfortunately now have Zero charge.
- My charger makes a noise, I think it always did, so I'm assuming the charger is OK.
Can anyone confirm that the chargers give off a kind of electrical buzz when working?
- I get no light at all on my A500. If the charger is OK I'm thinking something has gone within the tab, be that circuit or battery.
Any ideas or tips here?
- Sadly I do not have a multi-meter to test either the charger or the tab, no friends with a similar device, I've lost my proof or purchase (which is painful and rules out warranty), and am a bit stuck what to do.
Any ideas?
- I've heard/read that allowing the power to drop too low can cause a problem. Obviously Zero is bad in this case. Y
Can anyone confirm this rumour or suggest a fix?
- I did try entering recovery and resetting the battery stats - whether this made things worse or not is unclear - it certainly did not help.
ANY HELP OR IDEAS WELCOME (bear in mind that I have spent quite some time searching and trying other peoples' ideas already though.
Thanks,
Click to expand...
Click to collapse
Quit guessing and get the charger checked
In reply to myself and to help those with a similar issue.
Yes a charger my buzz when good OR bad. The trick to seeing whether it is working or not (aside from it charging the pad) is to see if it gets warm -- no warmth, probably broken.
As for measuring with a multimeter the trick is to insert a paper clip into the small hole in the plug and measure the voltage between the outer plug (negative) and the paperclip (linked to the positive). Few multimeters have pins that will fit inside the super tiny plug on the A500 charger so the paperclip is your way in - obviously be sure not to short circuit the thing!
There are many chargers available out there. In Australia Jay-Car and **** Smith both have perfect chargers, the correct type, voltage, amps etc, they even come with multiple pins -- sadly none fit the A500!
My solution was to go to Infinity who are a provider of Acer spare parts. They have the correct charger and are easy to deal with BUT -- It's not cheap! They want $40 for the charger and a further $30 for the little bit on the end that gives the plug its nationality. In most cases we do not need this though as we can reuse our old one, but hey, not cheap all the same.
Still, it works and I'd rather be ripped off than get the wrong thing and blow the mother board.
NOTE: if you do get a charger from anyone other than Acer or a supplier of theirs - be sure to match every detail of your current charger - especially polarity.
I had problems with charging on my A500. When I plugged in the charger the power button would turn orange for a few seconds and then start flashing white.
I took the back cover off and found that the wire to the centre pin of the power connector on the tablet had almost broken off. I touched it lightly and it came away. Re-soldering the wire fixed the problem, it now charges as expected.
After fixing it I measured the charge current. It starts at a small value for a few seconds and then jumps to full charge rate. It seems there was enough of a connection to handle the small current but as soon as it switched to full charge current the voltage drop across the remains of the connection was too much and charging stopped.
Charging problem
I too just experienced the no charging problem. I looked up how to open up the tablet and tried to trouble shoot the problem myself. My problem turned out to be a very easy fix. The Posative lead on the back of the charger port had come loose, a simple touch of the soldering iron and its fixed. I thought since I had it open I might as well go ahead and change the battery too since it was 4 years old. Its an old tablet and time to turn it into a hand me down for a lucky niece or nephew
Hi. My phone got wet in my jacket pocket while riding my motorbike. It was probably wet for an hour or so before I got home and started attending to it. Obviously as it was in my pocket it didn't get submerged or anything, but i still found water residue inside. I took it apart, submerged the motherboard in isopropyl alcohol for a couple of hours and then left it to dry. Today it is booting up however I have noticed a couple of problems.
The phone will not start up unless it is connected to a power source when I try to start it. It will stay on if i unplug it.
It won't charge. First time I booted it it said 41%. As soon as I restarted it had dropped to 17% and is now falling even when plugged in. It does claim to be charging when connected however.
The front camera looks like one of those face-morphing apps (Is there's water around the lens or something?).
It also feels quite hot around the top of the phone when it isn't doing anything.
The loud speaker is not working (fine, I'm guessing that's just a case of swapping it out).
Could the first two just be the battery or some sort of issue with the USB interface? Any ideas how to fix these issues? Thanks!
Clean your usb port. I sometimes clean it with 99% alcohol and a toothbrush when I got some moister damage.
When you charge it, check battery stats and see if it says that it's usb connected.
If so, then you might need to flash a custom kernel (I used Ktoonz for it) and raise the charging stream true usb.
Because your usb port got wet, it thinks you are charging true usb. When charging true usb it will charge way slower. It's als probably the cause for your phone getting hot for no reason.
Lennyz1988 said:
Clean your usb port. I sometimes clean it with 99% alcohol and a toothbrush when I got some moister damage.
When you charge it, check battery stats and see if it says that it's usb connected.
If so, then you might need to flash a custom kernel (I used Ktoonz for it) and raise the charging stream true usb.
Because your usb port got wet, it thinks you are charging true usb. When charging true usb it will charge way slower. It's als probably the cause for your phone getting hot for no reason.
Click to expand...
Click to collapse
I will try that now! Any idea why it won't start unless connected? I've just not a new battery, no change on that issue.
EDIT: It's now starting fine. I'm waiting for a replacement USB connector to hopefully fix the charging issues. It's still getting hot when it's just sitting on the table and the battery is draining at light speed.
icedragon999 said:
I will try that now! Any idea why it won't start unless connected? I've just not a new battery, no change on that issue.
EDIT: It's now starting fine. I'm waiting for a replacement USB connector to hopefully fix the charging issues. It's still getting hot when it's just sitting on the table and the battery is draining at light speed.
Click to expand...
Click to collapse
Good to hear it's booting again. From my experience these issues are temporarily and will disappear over time. The kernel and changing the charging speed fixed the same issues for me. I'm now running my normal kernel without any tweaks. So you might try it before swapping the connector. But that's up to you.
Lennyz1988 said:
Good to hear it's booting again. From my experience these issues are temporarily and will disappear over time. The kernel and changing the charging speed fixed the same issues for me. I'm now running my normal kernel without any tweaks. So you might try it before swapping the connector. But that's up to you.
Click to expand...
Click to collapse
I had already ordered the bits and they were only cheap so went ahead and swapped them out. New USB connector flex and new speaker. Frustratingly I still have no sound. It's charging fine but the battery is still dropping off a cliff (like half an hour from fully charged) and it's still getting hot. I even gave the motherboard and connectors a good clean with high purity alcohol and some cotton swabs. Could the board have suffered permanent damage potentially?
Strangely, none of the water indicator stickers have triggered and it's still in warranty so if worst comes to worst I guess I can go down that avenue.
So there's lots of questions about bad battery life but haven't found my issue in searches - altho I suspect my issue is a factor for many to some degree.
N4 took a 4' to drop to concrete. Screen cracked. Replaced screen w/no problems. Ran fine for a while on stock 4.4.4. Lollipop comes OTA practically zero day and since the N4 isn't my primary phone I upgrade to play around. Shortly after 5.0, the battery drains and shuts the phone off. I charge it overnight, pull it off, battery is dead, phone shuts down. Will stay on and operate fine on wireless charger but powers down if not connected. Pop off the back again to make sure battery connector is snug and reassemble. Now I've got red light of death. Get Google logo and can boot to recovery options but it just cycles. Disassemble again and ultimately find that the battery pins from the mainboard and their little black housing have come off at some point. Try to solder it back on but there's chips on the back side and there's just no room to get the solder on and pins reconnected. Not w/my skills anyway.
My main question is, has anyone successfully reconnected that annoying mofo? Thinking about skipping the connectors and just soldering wire straight from the battery to the board. I don't see anything in that connector that would be a problem if absent, but any warnings I should know about? Other workarounds?
This is not mission critical, just principle/spite.
Repaired?
gkmocv said:
So there's lots of questions about bad battery life but haven't found my issue in searches - altho I suspect my issue is a factor for many to some degree.
N4 took a 4' to drop to concrete. Screen cracked. Replaced screen w/no problems. Ran fine for a while on stock 4.4.4. Lollipop comes OTA practically zero day and since the N4 isn't my primary phone I upgrade to play around. Shortly after 5.0, the battery drains and shuts the phone off. I charge it overnight, pull it off, battery is dead, phone shuts down. Will stay on and operate fine on wireless charger but powers down if not connected. Pop off the back again to make sure battery connector is snug and reassemble. Now I've got red light of death. Get Google logo and can boot to recovery options but it just cycles. Disassemble again and ultimately find that the battery pins from the mainboard and their little black housing have come off at some point. Try to solder it back on but there's chips on the back side and there's just no room to get the solder on and pins reconnected. Not w/my skills anyway.
My main question is, has anyone successfully reconnected that annoying mofo? Thinking about skipping the connectors and just soldering wire straight from the battery to the board. I don't see anything in that connector that would be a problem if absent, but any warnings I should know about? Other workarounds?
This is not mission critical, just principle/spite.
Click to expand...
Click to collapse
So were you ever able to get the connector solder back on? I think mine break because it was to hot when I was removing the battery. My nexus 4 shutdown on me, my battery was expanded. I was wondering why my screen was being pushed out. I wonder if Android 5.0.1 is causing phone to run to hot. Never did this with Android 4.4.4. Hope the connector can be fixed. Maybe I take it to a solder shop.
jameswhite4684 said:
So were you ever able to get the connector solder back on? I think mine break because it was to hot when I was removing the battery. My nexus 4 shutdown on me, my battery was expanded. I was wondering why my screen was being pushed out. I wonder if Android 5.0.1 is causing phone to run to hot. Never did this with Android 4.4.4. Hope the connector can be fixed. Maybe I take it to a solder shop.
Click to expand...
Click to collapse
Not yet. I pulled the connector back off and cleaned everything up. I found that even very small gauge solder is too sloppy for the 4 small connections. Not to mention there's chips on the back side so you can't linger too long with heat. So my plan is to try again with some conductive ink and/or gel. If that doesn't work I'm just going to use wires to bridge the battery right to the board. Haven't had time to work on it but I'll follow up here when I do.
Did you get a replacement battery? Lithium batteries can swell because of overcharging. There are definitely more than a few N4 owners who had the same issue. A replacement battery won't solve that problem but it could be more tolerant of it, for a while - and depending on if it was "user error" or a fault in the phone's overcharging protection circuitry. Don't go to the trouble of having someone solder the connector back on with the old battery.
My usb port seems to have died the other day. It stopped charging and gives the message about an incompatible charger. I have tried Ll of the suggestions except factory reset. I ordered a Qi charger could and was planning on just wireless charging until I decide what I will replace this one with.
But, today the phone has started popping up a message randomly when I don't have it plugged in. It seems to be keeping it from sleeping and my pocket is vibrating as much as a couple dozen times a minute. Is there a way to disable the port in software since it appears broken?I just need a few weeks worth of life out of it till I get the new device and have everything up and running.
I know this is an old phone, but I thought there might still be some people who might know about lollipop on here. I'm currently rotating batteries since my qi adapter didn't arise before leaving town. But, the constant buzzing is pretty annoying. I can mute the phone to avoid it (I assume) but then I miss all incoming traffic.
So I gather I won't get a response. I'm still crossing my fingers...
I bought a wireless charger and adapter from amazon. It works, but it appears every time the usb cable message occurs, the charging stops. In 6 hours last night it continually toggled from charge to not (turning the screen on). I went from 22% to 35%. Not impressive.
bkenobi69 said:
So I gather I won't get a response. I'm still crossing my fingers...
I bought a wireless charger and adapter from amazon. It works, but it appears every time the usb cable message occurs, the charging stops. In 6 hours last night it continually toggled from charge to not (turning the screen on). I went from 22% to 35%. Not impressive.
Click to expand...
Click to collapse
Maybe try checking your usb port for foriegn matter/ bent pins before giving up. Ive had that happen on a couple different phones. Made all kinds of havoc. Even a small bit of lint can hold moisture and cause pin shorts
Thanks for the suggestion. I blew the port out with both canned air and my air compressor. I also tried using a tooth pick to scrape the contacts with and without isopropyl alcohol. I read somewhere that slightly bending the pins/center body up can help in case it was pushed down. I didn't see any change when I tried using my plastic screen pry tool.
It appears that the message pops up more when the battery is below 30% for some reason. I have no idea why though.
BlueCyclone said:
Maybe try checking your usb port for foriegn matter/ bent pins before giving up. Ive had that happen on a couple different phones. Made all kinds of havoc. Even a small bit of lint can hold moisture and cause pin shorts
Click to expand...
Click to collapse
I ended up changing providers and replaced the phone. I was able to get wireless charging working for the most part. It requires careful alignment of the phone and pad.
I checked for debris and pin damage, but nothing looked problematic. The only thing that helped in any way was using a plastic screw driver to pry up on the port. This did not fix it, but it stopped complaining all the time and made it usable with the Qi charger.
im on lineage os and after around %30 screen starts to blink and if it blinks much it reboot does anyone know a fix to this its really annoying
Re-seat and probably clean the contacts of the cables running across the battery on the backside. Only the battery connector is known to develop bad solder connections, but here probably just the two display cables are affected and somewhat loose, or just the one for the backlight.
Kenan07 said:
im on lineage os and after around %30 screen starts to blink and if it blinks much it reboot does anyone know a fix to this its really annoying
Click to expand...
Click to collapse
Battery. This is a common issue on samsung devices, you need to replace your battery.
The removal and reattachment of the second ribbon cable(the first is for usb) may actually fix the screen during a battery replacement.
I changed my battery from 2013 just a few weeks ago. Remaining capacity must've been around 50-60 percent. And it was bulging and rear plate and the touchscreen were bending iutward, too.
But no display issues.
Not even the corona (not the flu) effect some guy in the forum recently experienced, which may have been caused by pressure from the battery. And the sudden disapperance of this effect may have meant that there was a gas exhaust from the battery's two cells, flattening them...