after I flash with CWM, I get this when it trys to boot android "nand kernel open failed"
Also, in CWM, I get "E:Can't find misc"
installing nand without CWM works.
bump- I searched and didn't find anything helpful. I've tried 3 different roms
"Can't find misc" should only appear if you don't have a misc partition in NAND. (which is created when flashing CWM)
And nand kernel open failure probably means theres no zImage or initrd.gz in the boot partition.
Try flashing CWM from the CWM thread and then a ROM.
Gabe3 said:
after I flash with CWM, I get this when it trys to boot android "nand kernel open failed"
Also, in CWM, I get "E:Can't find misc"
installing nand without CWM works.
Click to expand...
Click to collapse
How did you transfer the zip file to SD? Did you use magldr? If so try re-transfering using your comp, as Magldr sometimes corrupts them.
Ricey
I have this same problem. I reflashed cwm and now i dont get the misc but no matter which rom i install from cwm i always get the kernel error =\
d34thd34l3r said:
I have this same problem. I reflashed cwm and now i dont get the misc but no matter which rom i install from cwm i always get the kernel error =\
Click to expand...
Click to collapse
just redo everything. that fixed it for me.
Bump.
Did a clean install of TyphooN CyanogenMod 7 Nightly v3.3.1 and got the "nand kernel open failed" error.
I formated the SD-Card two times, reinstall cwm 150mb partition 3 times and still get the same error, first time within almost 1 year of android on my HD2 ._.
Any ideas or solutions welcome.
and another bump and sorry for my bad english =)
i get the "nand kernel open failed" error too.
i installed radio and hspl 2.08
then flashed MAGLDR 1.13
continued with CWM (250mb)
then formated my sd-card und put TyphooN CyanogenMod 7 on it
after installation, i get the error.
redid all 2 times now, nothing works.
NEED HELP ^^
Likewise i am getting it with hyperdroid v12
I've just got it with HD2 NDT MIUI GINGER ROM V13.0 Multilang :/ I reinstalled magldr,clm and the rom and formated in clm but still get the error! :S
[★] said:
I've just got it with HD2 NDT MIUI GINGER ROM V13.0 Multilang :/ I reinstalled magldr,clm and the rom and formated in clm but still get the error! :S
Click to expand...
Click to collapse
i say you have to do a clean wipe starting fro scratch task 29 it ad redo
bckstn said:
and another bump and sorry for my bad english =)
i get the "nand kernel open failed" error too.
i installed radio and hspl 2.08
then flashed MAGLDR 1.13
continued with CWM (250mb)
then formated my sd-card und put TyphooN CyanogenMod 7 on it
after installation, i get the error.
redid all 2 times now, nothing works.
NEED HELP ^^
Click to expand...
Click to collapse
me too same massege
bckstn said:
and another bump and sorry for my bad english =)
i get the "nand kernel open failed" error too.
i installed radio and hspl 2.08
then flashed MAGLDR 1.13
continued with CWM (250mb)
then formated my sd-card und put TyphooN CyanogenMod 7 on it
after installation, i get the error.
redid all 2 times now, nothing works.
NEED HELP ^^
Click to expand...
Click to collapse
Typhoon doesn't use 250mb CWM, use the one provided with rom 150MB System/5MB Cache (ClockworkMod Recovery v3.0.2.5), most "nand kernel open failed" are down to wrong CWM size
I'm getting the same error, but only with sense 3.0 roms. Any other roms I've used have installed have worked. Is there a certain step I'm missing with installing sense 3.0 roms? I'm using MAGLDR v1.13 and Clockwork Recovery Mod v3.0.2.5. I flashed recovery_150m_cache_5m.zip onto the phone using magldr usb flasher. Any ideas?
cludseph said:
I'm getting the same error, but only with sense 3.0 roms. Any other roms I've used have installed have worked. Is there a certain step I'm missing with installing sense 3.0 roms? I'm using MAGLDR v1.13 and Clockwork Recovery Mod v3.0.2.5. I flashed recovery_150m_cache_5m.zip onto the phone using magldr usb flasher. Any ideas?
Click to expand...
Click to collapse
150mb for sense rom is definitely to low!
Read the rom's thread carefully guys!
It says there what CWR partition is needed.
Sense roms need SD CARD PARTITION so read the thread (it's first page).
If you have read it and your CWR partition looks exactly as it was given in the rom's thread then do task29, hspl, magldr 1.13 and CWR.
If it still doesn't work try different roms or try CLK.
Thanks for the response. How do I create a 5/240/5 partition through CWR? The last partition I made was just installed through .zip on CWR. Sorry for the questions, new to the hd2.
do all beginners understand this? you are probably putting the 'clk' version of the rom in your storage card for installation. you need the 'magdlr' version of the rom for clockwork mod to correctly install android
musashiz said:
do all beginners understand this? you are probably putting the 'clk' version of the rom in your storage card for installation. you need the 'magdlr' version of the rom for clockwork mod to correctly install android
Click to expand...
Click to collapse
Hi guys, i had the same problem, and i figured maybe i can show u what i did, to help u.
i went to THIS thread and followed the instructions:
"Installation Guide for MAGLDR 1.13"
the error occured right after i flashed the MAGLDR_CWM_Recovery_v3.2.0.0_for_NexusHD2_135M.zip onto my HTC HD2.
the only thing i had to do was enter magldr boot menu (hold off button while booting)
then i choose AD RECOVERY
CWM started up and i choose install zip from SD card
ofcourse i have placed NexusHD2-Gingerbread_V3.0_NAND_(Android-2.3.5).zip onto the ROOT of my SD card previously.
the .zip file installed perfectly and then i rebooted my phone.
all was ok after that..
hope this helps!
musashiz said:
do all beginners understand this? you are probably putting the 'clk' version of the rom in your storage card for installation. you need the 'magdlr' version of the rom for clockwork mod to correctly install android
Click to expand...
Click to collapse
Awww, that was my mistake. It's working with the MAGLDR version now. Thanks for pointing that out
musashiz said:
do all beginners understand this? you are probably putting the 'clk' version of the rom in your storage card for installation. you need the 'magdlr' version of the rom for clockwork mod to correctly install android
Click to expand...
Click to collapse
No we do not, thank you, this helped.
Hello.
I have tried several times to flash a CWM ROM (I follow the instructions fully) from my sd card every time it reboots after the unzip from my sd card it just goes to the lock screen then just shuts down. Any ideas why this is happening?
Thank you for your help.
read the rom guide in relation to the build you're trying to flash.
You need to make sure if using MAGLDR 1.13 that you are flashing the correct partition to start with, what rom are you trying to install?
some roms require specific partition sizes. i had the same problem kinda with my current rom until i applied the specific CWM partition.
bates_1974 said:
read the rom guide in relation to the build you're trying to flash.
You need to make sure if using MAGLDR 1.13 that you are flashing the correct partition to start with, what rom are you trying to install?
Click to expand...
Click to collapse
CMYLXGOs.Stock.Desire.HD.v2.0.9n.NAND.RMNET.NO-SQUASH-MDJ.S10.4OC_CWM
He uses special cwm thingS. He should have .zips posted. I'm using his desire HD rom
Sent from my HTC HD2 using Tapatalk
Hi! I've got 2 question for everyone that could help me...
1) How clockwork mod work in HD2?
2) How could i remove it from my device? (task29/ rom Flashing / SD rom Flashing)
Thanks in advance!
Im no expert when it comes to CWM but I can give you a brief explanation....
You need to flash MAGLDR to your phone first (Assuming you already have HSPL 2.08).
Then flash CWM. Which you access through the MAGLDR menu to flash your ROM.
It can be removed by entering bootloader and flashing a WM6.5 / 6.5.x ROM...
See this thread for a complete guide to going over to the dark side...
Hope that helps..........
conantroutman said:
Im no expert when it comes to CWM but I can give you a brief explanation....
You need to flash MAGLDR to your phone first (Assuming you already have HSPL 2.08).
Then flash CWM. Which you access through the MAGLDR menu to flash your ROM.
It can be removed by entering bootloader and flashing a WM6.5 / 6.5.x ROM...
See this thread for a complete guide to going over to the dark side...
Hope that helps..........
Click to expand...
Click to collapse
Thank you!
I was scared about removing the clockwork mod! There are tons of guides & videos about the installation, but nothing about the unistallation!
I've tried some DAF Android Builds, but now i can try .zip rom quietly!
Great!!
Hi,
a friend gave me an HD2 which stopped booting about three months ago, when he tried to install android on it, without really knowing what he was doing.
I have a bit of experience in installing custom roms in some android devices (HTC Vision, Samsung P1000...), but I know nothing about HD2 or any windows phones.
This is what it says after switching on:
tinypic.com/r/2hywdp4/5
This is after switching on with windows key pressed:
tinypic.com/r/29y43fb/5
This is after switching on with volume key pressed:
tinypic.com/r/25i3f9c/5
[sorry I can't create links because I'm new to xda]
Is there a way to go back to a working status?
If I fix it, I'll earn some glory and a free beer.
The final aim would be to install a NAND android rom, preferably CM7 or similar.
Thanks a lot.
Correct me if i'm wrong guys, but this pic :
tinypic.com/r/25i3f9c/5
is the bootloader mod and it says that you have HSPL 2.08
In my opinion, you just have to flash back a windows 6.5 ROM and follow the whole process to get android (Flash MAGLDR, [....] , and flash a CM7 NANDROID Rom using the clockworkmod) refering to the tutorials in the NANDROID section.
Its not bricked. Just restart the process to install Android as jediL pointed out and you should be good to go. Check here for a detailed explanation on how.
Ok the pictures help a lot. From what I see the first picture is what you see when you boot a HD2 that has clk installed for the custom bootloader but does not have as Android ROM in memory to boot. This is the only reason you well ever see clk at all if you just power on a HD2 with clk installed.
The second pictures is clk trying to boot into recovery but is not able to. It probably either has some kind of problem booting the flashed version or it just does not have a custom recovery flashed to it. My bet is it does not have a custom recovery flashed to it. As most people have problems Glasgow.g a recovery after flashing clk if they are not using the HD2 NAND Toolkit.
The third picture is the the stock bootloader of the HD2 and yes it shows you have HSPL 2.08 installed so you are good with HSPL and do not need to flash HSPL 2.08 to your HD2.
Now to get you on to getting Android up and running. Seeing as you already have clk on your HD2 you do not need to flash it. You do need to flash a custom recovery and you can either check out the guide linked in my sig to flash it via fasboot comands manually or you can use the HD2 NAND Toolkit to flash it in a more automatic way, or to be more specific a more noob friendly way. There is a link to the toolkit in the guide linked in my sig.
You need to pick out what Android ROM you want to use and read the first few post by the ROM chef to see what partition size you need to have and use the Toolkit to repartition the NAND memory to that size. Next download the .zip file for the ROM, make sure you get the version that is for clk. Some ROMs have only one version though that works with MAGLDR and clk. Next copy the .zip to the root of your SD card and then power on your HD2 holding down the home button and your recovery will boot up. Then just find the option that says install from SD card and then select the ROM file and flash it.
I installed HD2 NAND Toolkit.
I executed the following operations:
- Wipe (Task29)
- cLK repartition (150mb)
- cLK install recovery
then I rebooted into CWM recovery and installed the HyperDroid rom.
Now I have a fully working CM7-based android phone!
Thanks a lot!
idk if im in the right spot sorry
but anyways im pretty familiar with the flashing stuff already flashed my phone back to the original windows6.5 but i dont like it , i want an android rom but the ones that i want seem very difficult ive tried many times to flash the bliss sense 3.5 rom to my phone but i cant get it going properly , it keeps rebooting ....
am i doing something wrong ?
i start from stock , then i flash the 2.08.HSPL
then i flash the custom RUU radio 2.15
then i flash the MAGLDR v1.3
then i flash clockworkmod 3.0.0.5
then i put the bliss sense 3.5 rom on my sd card without etracting it because when i extract it , it gives me a bunch of uneccesary files ?
then i boot into CWM and update the rom threw the zip like normal , it loads up fine and even says rom is finished
but when i reboot it gets stuck on a boot loop
Everything is fine, except you perhaps didn't set up partitions correctly, and haven't made an ext partition on your sd card which is probably required by that rom( since it's a sense!).
You may follow this short guide on how to do the above. You can skip the steps that you've already done.