Hello,
I installed Sam's ICS RC2 for SGS and it's amazing, however, wifi works but I can't connect to network, the phone fails to connect. I have tried flashing other modem (XXJVT i reckon) without any result.
Any ideas?
Thanks.
having same issue but with another build of ICS
vaulner said:
Hello,
I installed Sam's ICS RC2 for SGS and it's amazing, however, wifi works but I can't connect to network, the phone fails to connect. I have tried flashing other modem (XXJVT i reckon) without any result.
Any ideas?
Thanks.
Click to expand...
Click to collapse
0utkast said:
having same issue but with another build of ICS
Click to expand...
Click to collapse
Go to Settings. Under Wireless Networks select More... Select Mobile Networks. See if Data enabled is ticked.
vaulner said:
Hello,
I installed Sam's ICS RC2 for SGS and it's amazing, however, wifi works but I can't connect to network, the phone fails to connect. I have tried flashing other modem (XXJVT i reckon) without any result.
Any ideas?
Thanks.
Click to expand...
Click to collapse
I do not see how a new modem will affect WiFi. AFAIK, the wifi stuff is built into the kernel.
Does this happen for any wifi network? Have you tried connecting to some other network?
If nothing connects, you might be looking at a factory reset and data wipe
sencafe said:
Go to Settings. Under Wireless Networks select More... Select Mobile Networks. See if Data enabled is ticked.
Click to expand...
Click to collapse
Data enabled setting is for data transfer over GPRS/EDGE/3G networks, not related to WiFi at all!
Try (without warranty) the patch made by Pawitp for the build 10:
http://forum.xda-developers.com/showthread.php?t=1363593&page=545
Best regards,
Biz. ♂
adityajaltade said:
Data enabled setting is for data transfer over GPRS/EDGE/3G networks, not related to WiFi at all!
Click to expand...
Click to collapse
I agree. I may have misunderstood the question. The OP said that wifi works and he can't connect to network. I understood that to be the mobile network seeing that he is talking about modems.
Wifi has nothing to do with modems.
Aah! Now that I read it again... I think I understand what you understood. The OP is a bit ambiguous in that case
adityajaltade said:
Aah! Now that I read it again... I think I understand what you understood. The OP is a bit ambiguous in that case
Click to expand...
Click to collapse
What I was saying is that the phone does not ask me for my PIN code and therefore, I can not make any call
I will try wiping later, thanks for your help
vaulner said:
What I was saying is that the phone does not ask me for my PIN code and therefore, I can not make any call
I will try wiping later, thanks for your help
Click to expand...
Click to collapse
Perhaps it is an issue with the pin unlocking code. Can you put the sim in another phone, remove the SIM lock pin, then try it back in the Galaxy. It might narrow down the issue for the devs.
I have try ics on miui galnet! It uses JV5 as modem! My signal is the best! I have try more modem but with ics signal is very good! I do not test consume! If you want, you can install other modem! I suggest JPG modem! It works fine and less consume of battery!
My operator is H3g italy!
You can find you modem only trying it!
You measure performance signal (3g, 2g, wi-fi, gps) through apps market about signal and consume with time elapsed.
i'm using the zsjpg modem with ICS (for cyanogen kernels). very good modem.
edit: if the cwm installation doesn't work, try the updated version (like the new thunderbolt scripts).
edit2: it seems like the zip doesn't work anymore for new ICS builds :/
Related
First, as you can assume, i have the HTC Hero...since i was not satisfied with the 1.5 version ( android ) i updated it to 2.1 ( Eclair version )..now the problem is that when i add the APN settings, it starts the 3G network and i don't have any option to "close" it...on the 1.5 version i had a the Wifi, Bluetooth and i think Data connection, but now only the Wifi, Bluetooth... so in a summary, i can open and close the wifi and bluetooth but i can't regulate the 3G network, when i set it, it starts and there is no way to turn it off...
So does anyone has an idea how to solve this?
Thanks in advance
How about when you hold the power button, do you get the "Mobile Network" option to select there?
ddotpatel said:
How about when you hold the power button, do you get the "Mobile Network" option to select there?
Click to expand...
Click to collapse
No, just the silent option, airplane, reboot or turn off...
The irony is that when i turn Wifi on, the 3G also turns on...but when i close the wifi the 3G still works...
It seems i have the Nexus One software on my Hero, i received a mail from google, welcome to the world of Nexus one... OMG...
wkulen said:
It seems i have the Nexus One software on my Hero, i received a mail from google, welcome to the world of Nexus one... OMG...
Click to expand...
Click to collapse
What ROM are you using?
ddotpatel said:
What ROM are you using?
Click to expand...
Click to collapse
Android 2.1, VanillaEclair 1.3
wkulen said:
Android 2.1, VanillaEclair 1.3
Click to expand...
Click to collapse
Maybe ask in that thread.
Or flash a diff ROM and see if you still have the same issue.
ddotpatel said:
Maybe ask in that thread.
Or flash a diff ROM and see if you still have the same issue.
Click to expand...
Click to collapse
I will flash an other ROM, do you have any suggestions, which one is the fastest and most stable?
wkulen said:
I will flash an other ROM, do you have any suggestions, which one is the fastest and most stable?
Click to expand...
Click to collapse
Im using MCR3.2. (Link in my signature). Fast and stable,... No issues whatsoever. But it is still only an Android 1.5 ROM. I'm planning on adding the 768mhz overclock kernal to it tonight, hopefully will fly like a Legend then.
Ooops,... Sorry
You not the only one with this puzzling problem wkulen! Same rom as you, and it seems I can't close 3g even with that APNdroid is set to be off! It looks like it still using data from 3g - hope not otherwise it could be a costly mistake!
i've got the opposite problem...
ROM: current official...
My 3g or data internet connection sometimes doesn't turn on when I switch off the wifi. But it happens most of the time, but not all the time. What I normally do everytime is to go to Settings/Wireless controls/Mobile network settings/Network operators - and I "select automatically". Then my network data kicks back in. It's a hassle but I don't know what else to do.
Flashed 3-669-SuperScaryStable on top of nightly cm7 212. Subsequently, WiFi could not maintain a lock. The phone would find the wifi network get a lock for a moment and immediately lose the lock. Get a lock, lose the lock. . . . Settings I tried were Scary and smartass governors 245mhz - 1.2ghz
Anyway, flashed nightly 220 (back to regular cm7 kernel)-- back to wifi working fine.
Maybe I looked too quickly but all I saw in the development thread pertained to Super Scary not working with sense roms.
Hmmmm.
sdk234 said:
Flashed 3-669-SuperScaryStable on top of nightly cm7 212. Subsequently, WiFi could not maintain a lock. The phone would find the wifi network get a lock for a moment and immediately lose the lock. Get a lock, lose the lock. . . . Settings I tried were Scary and smartass governors 245mhz - 1.2ghz
Anyway, flashed nightly 220 (back to regular cm7 kernel)-- back to wifi working fine.
Maybe I looked too quickly but all I saw in the development thread pertained to Super Scary not working with sense roms.
Hmmmm.
Click to expand...
Click to collapse
Download wifi analyzer from market and figure out what is conflicting with your wireless router.
toastcfh's stock kernel is considered the most stable kernel because it's been tested and proven to work with everything time and time again.
However, I have no problems with wifi on Scary's kernel. Again, I'm not saying there are no issues because when I'm at work I do have issues but I have wifi issues on my laptop with the wifi here as well, they have way too many APs broadcasting on the same channel (4-5 APs for channel 3, 4-5 APs for channel 7, 4-5 APs for channel 11) so I seriously doubt it's a problem with the kernel but more a problem with your local wifi router configuration.
Run wifi analyzer and it will answer this question.
Am I right to assume that I should run the test you recommend after flashing Scary and recreating the problem - cause on Toastcfh's kernel there is no problem connecting to that router whatsoever?
sdk234 said:
Am I right to assume that I should run the test you recommend after flashing Scary and recreating the problem - cause on Toastcfh's kernel there is no problem connecting to that router whatsoever?
Click to expand...
Click to collapse
You can run the same test on toast's kernel.
Well, you know, maybe it's just all about the goofy phone itself after all.
Trying to do the test (following a reboot) I'm just about sitting on top of the router (that I've confirmed is working) with wifi enabled on the shift and all I'm getting is "not in range." Can't get the wifi icon to even display at the moment.
Thanks for the help.
sdk234 said:
Well, you know, maybe it's just all about the goofy phone itself after all.
Trying to do the test (following a reboot) I'm just about sitting on top of the router (that I've confirmed is working) with wifi enabled on the shift and all I'm getting is "not in range." Can't get the wifi icon to even display at the moment.
Thanks for the help.
Click to expand...
Click to collapse
Open ROM manager and run fix permissions and reboot again, then turn on wifi and open wifi analyzer again.
VICODAN said:
Open ROM manager and run fix permissions and reboot again, then turn on wifi and open wifi analyzer again.
Click to expand...
Click to collapse
Did it. But seems that I've got the same problem. Connects for a little bit and then disconnects. It just can't maintain the wifi link. Doesn't stay up long enough to even get a screen shot of wifi analyzer.
Maybe I should try another nightly, stable cm7 or sense?
sdk234 said:
Did it. But seems that I've got the same problem. Connects for a little bit and then disconnects. It just can't maintain the wifi link. Doesn't stay up long enough to even get a screen shot of wifi analyzer.
Maybe I should try another nightly, stable cm7 or sense?
Click to expand...
Click to collapse
You can't take screenshots on wifi analyzer. Just analyze it yourself. How many APs are broadcasting on the same channel as you? More than 1? Change the channel.
There are two and they don't overlap. One is centered over channel 6, the other (weaker one) centered over channel 11. But the problem is that the parabolas that show the signal strength disappear pretty quickly and the wifi indicator at the top of the phone just disappears. What do you think about the possibility that I should switch to a different nightly or sense?
sdk234 said:
There are two and they don't overlap. One is centered over channel 6, the other (weaker one) centered over channel 11. But the problem is that the parabolas that show the signal strength disappear pretty quickly and the wifi indicator at the top of the phone just disappears. What do you think about the possibility that I should switch to a different nightly or sense?
Click to expand...
Click to collapse
Ignore the APs disappearing. It sounds like your router is either a piece of junk or misconfigured.
Try configuring the wireless radio on channel 1.
Shouldn't be a piece of junk. wasn't that cheap ;-)
Works fine with my computer anyway.
sdk234 said:
Shouldn't be a piece of junk. wasn't that cheap ;-)
Works fine with my computer anyway.
Click to expand...
Click to collapse
That means nothing.
What kind of router is it? Manufacturer / Model number?
Also please remove ScaryKernel from the title of this thread since we have proven this problem happens on toastcfh's kernel as well.
VICODAN said:
That means nothing.
What kind of router is it? Manufacturer / Model number?
Also please remove ScaryKernel from the title of this thread since we have proven this problem happens on toastcfh's kernel as well.
Click to expand...
Click to collapse
Netgear N600 WNDR3400
Why's it meaningless that I have no trouble with WIFI on laptop?
sdk234 said:
Netgear N600 WNDR3400
Why's it meaningless that I have no trouble with WIFI on laptop?
Click to expand...
Click to collapse
Netgear sucks. Do yourself a favor and go buy a Linksys WRT610N or one of the new models.
Other than that all I can tell you is switch your wireless channel.
It's not a problem with the phone or the kernel, it's the router.
VICODAN said:
Netgear sucks. Do yourself a favor and go buy a Linksys WRT610N or one of the new models.
Other than that all I can tell you is switch your wireless channel.
It's not a problem with the phone or the kernel, it's the router.
Click to expand...
Click to collapse
Ok - I'll try switching the channel first ;-)
Also - going to find some other routers to test the phone against
Thanks for all the time spent troubleshooting here
Ok - Vic - here's the end of the story, since you've been good enough to work with me on this - -
Installed and ran an app called "FXR WiFi fix and rescue" from the market. Didn't appear to help.
So, restored nandroid of Mik 1.6 and WIFI WORKS PERFECTLY once again. Strong, stable, consistent lock on the Netgear signal (and another close-by router as well.) Problem solved for me.
Not going to make any rash accusations about what the culprit may be which caused wifi to fail for me on cm7.
I'm happy I've confirmed it's not the phone.
Maybe my shift just likes MikRoms and Supreme Sense and was punishing me for experimenting!!
sdk234 said:
Ok - Vic - here's the end of the story, since you've been good enough to work with me on this - -
Installed and ran an app called "FXR WiFi fix and rescue" from the market. Didn't appear to help.
So, restored nandroid of Mik 1.6 and WIFI WORKS PERFECTLY once again. Strong, stable, consistent lock on the Netgear signal (and another close-by router as well.) Problem solved for me.
Not going to make any rash accusations about what the culprit may be which caused wifi to fail for me on cm7.
I'm happy I've confirmed it's not the phone.
Maybe my shift just likes MikRoms and Supreme Sense and was punishing me for experimenting!!
Click to expand...
Click to collapse
Glad to hear it but I'm still wondering.. did you even TRY changing the channel?
I get 20+Mbps over Wifi on 2.4ghz.
I was planning to try changing the channel, but you know what -- just happened to restore Mik 1.6 first.
And the result was dramatic. On the nightly CM7 the graphs displayed on wifi analyzer weren't stable at all. Even when the parabola's appeared for a few moments, their height was shifting up and down. It was like the signal strength was fluctuating.
On Mik's rom the height of the parabolas is higher than I saw before and just stays put.
sdk234 said:
I was planning to try changing the channel, but you know what -- just happened to restore Mik 1.6 first.
And the result was dramatic. On the nightly CM7 the graphs displayed on wifi analyzer weren't stable at all. Even when the parabola's appeared for a few moments, their height was shifting up and down. It was like the signal strength was fluctuating.
On Mik's rom the height of the parabolas is higher than I saw before and just stays put.
Click to expand...
Click to collapse
Did you do a wipe data/factory reset when flashing CM7? Did you wipe dalvik? Did you wipe cache? Did you wipe battery stats? Did you flash the latest CM7 nightly and then right after that did you flash google apps 828 and new talk?
Not wiping properly before flashing a new rom could cause weird issues like that.
VICODAN said:
Did you do a wipe data/factory reset when flashing CM7? Did you wipe dalvik? Did you wipe cache? Did you wipe battery stats? Did you flash the latest CM7 nightly and then right after that did you flash google apps 828 and new talk?
Not wiping properly before flashing a new rom could cause weird issues like that.
Click to expand...
Click to collapse
Yes-wiped that & more - prboy trained me well
After wiping according to steps on mik's forum (& battery stats) , flashed cm7 and google apps and talk just as you instructed
Sent from my PG06100 using xda premium
Hi All,
Since I got my DEFY I have WiFi problems. This issue only exists when WiFI has WPA/WPA2 PSK authorisation.
It is going like this: I connect over the wifi. Then connection works fine, I am able to browse www, check the emails etc, and after few seconds, minutes the connection stops working but still exist. I try to reconnect several times. Defy shows that is connected but nothing works fine. Internet apps or Market gives a message like the time is up, connection lost. I have to forget the conection in settings or reset device to get it working properly, but not for long.
And the thing is that there is only ONE ROM that works fine with WiFi on my DEFY. This is Cyanogenmod-7.1.0-RC1. Other ROMs have same issues. Doesn't mater if it is Cyanogen mod 7.1 stable or any MIUI or MS2Ginger. I tried almost all roms but nothing helped. So I had to go back to CM7.1.0-RC1.
Do you know what should I do to make WiFi working fine on other roms?
greetings,
Gregory
p.s.
Please, just don't tell me that I should change authorisation on WiFi router. This is not a solution for me, because I use WiFi in a lot different places.
Same problem
Hi,
I have the same problem with my Defy since a few months, no solutions!
I have the *EXACT* same issue. Was about to roll back to stock and send it in for repair, glad I found your post! I'll install the ROM you suggested and keep hoping this gets fixed
just fixed my wifi issue for the second time. If there are to many remembered networks no more wifi. You can turn it on but it cant find any. delete all remembered networks and back on line. that is the only conectivity problem I have ever had after months of cm7
wilson1813 said:
just fixed my wifi issue for the second time. If there are to many remembered networks no more wifi. You can turn it on but it cant find any. delete all remembered networks and back on line. that is the only conectivity problem I have ever had after months of cm7
Click to expand...
Click to collapse
I think that's a different problem than we're having. It is finding the network just fine (and connecting) in our case. It's just that internet connectivity refuses to work after a few minutes, forcing us to disconnect-reconnect to get it working again
@OP: Thanks a lot! The ROM you mentioned does indeed not have this problem. It's not as stable as some of the more recent roms though, think I'll still be forced to revert to stock
i had exactly that problem with my first defy, no solution man, i send it to warranty and they give me other
maybe changing the regulatory domain channels from 11 to 14 could help. this option is hidden by default, you have to enable it: change the value of 'ro.debuggable' from 0 to 1 in /system/bootmenu/config/default.prop, save and reboot. after that, the regulatory domain setting will be shown in settings/wireless/wifi/advanced. simply change it to 14 channels.
Sent from my MB526 using xda premium
@OP: Apparently the issue still occurs on the version you mentioned as well...just happens less often.
cdlq456 said:
i had exactly that problem with my first defy, no solution man, i send it to warranty and they give me other
Click to expand...
Click to collapse
Hmm..weird thing is, I never had this issue on the stock ROM
zakoo2 said:
maybe changing the regulatory domain channels from 11 to 14 could help. this option is hidden by default, you have to enable it: change the value of 'ro.debuggable' from 0 to 1 in /system/bootmenu/config/default.prop, save and reboot. after that, the regulatory domain setting will be shown in settings/wireless/wifi/advanced. simply change it to 14 channels.
Sent from my MB526 using xda premium
Click to expand...
Click to collapse
Thank you for the suggestion! Just tried this, didn't resolve the issue sadly
I'm looking into rolling back to a stock Froyo rom but the information is scattered all over the place, I'm having a hard time figuring out if it's possible, and if so, how ;/
Anyone have any more ideas? ;/
darkdevil1 said:
Anyone have any more ideas? ;/
Click to expand...
Click to collapse
OK, maybe I just passed the signpost but... do you still have the problem if you set your "select network" setting to 3G only?
I ask because (and it may be different on my phone as I am USA, stock ROM with wifi calling) if you go into the INFO menu > phone information > set preferred network type, mine toggles between three radio preferences: "GSM only" (when wifi is active), "GSM auto (prl)" and -- if I set for 3G Only, "WCDMA only".
I have noticed that when "select network" setting is at automatic (or 2G only) it often has trouble transitioning from cell to wifi. And, when wifi is an issue, I find that "GSM auto (prl)" has been selected (which on my USA phone prevents wifi connection). However, it seems to have no issue whatsoever transitioning from "WCDMA only" (3G only) to "GSM only", which on my phone then allows wifi connection. Again, this is a wifi calling phone so may be different.
Yep, same here BUT ! I get root browser, found my build.prop and change wifi chanells first time for 14 and it didnt help so i try other and my wifi works in 100% with 13 chanells. Try it
This is a widely know problem, many people are affected more or less. I'm also having nerve-blowing times with wifi sucking all over... Stock Froyo (and now Cyanogen 7.2) seems to be a bit more stable, sometimes everything is fine for a few hours, all downloads go lightning fast - and then suddenly things are screwed up. I tried a lot of MIUI releases as I like it most. MIUI seemed the most problematic so far. I don't know what is the cause, new stock Motorola Gingerbread ROM versions also have this issue (except one I think - look it up in the forum).
Agree, bothering with the router is not a solution. My Nokia E51, my EeePC, my girlfriend's Omnia and Lifebook - all work perfectly with all the four routers we use frequently. Not a single glitch - everything is stable and nice, except Defy.
I don't think is a hardware problem with certain devices, it seems more to do with the way Defy handles wireless connections.
Anyway, it's frustrating but CM7.2 and CEE Froyo gives a bit better experience than others.
masspl said:
Yep, same here BUT ! I get root browser, found my build.prop and change wifi chanells first time for 14 and it didnt help so i try other and my wifi works in 100% with 13 chanells. Try it
Click to expand...
Click to collapse
You mean changing ro.wifichannels to 13?.
Don't do that, my phone wouldn't boot any more. Had to restore nandroid BU...
darkdevil1 said:
You mean changing ro.wifichannels to 13?.
Don't do that, my phone wouldn't boot any more. Had to restore nandroid BU...
Click to expand...
Click to collapse
I didnt know that... it help me but i see for other its bad
Mine boots fine...
VTomi1975 said:
Mine boots fine...
Click to expand...
Click to collapse
Strange, perhaps I messed up something else accidentally then. Has it resolved your problem?
My mate do same think but he leave space after "13" and there was some problems with boot after this ;/ So maybe u do same ... Im sory if i make some problem
darkdevil1 said:
Strange, perhaps I messed up something else accidentally then. Has it resolved your problem?
Click to expand...
Click to collapse
No, problem still persists. Sometimes it works flawlessly for hours. Then... suddenly screwed :S In some cases a "switch wifi on/off" workout can help but not always.
VTomi1975 said:
No, problem still persist. Sometimes it works flawlessly for hours. Then... suddenly screwed :S In some cases a "switch wifi on/off" workout can help but not always.
Click to expand...
Click to collapse
Same. Thanks for your response.
I've rolled back to 2.2 and no Wifi issues so far. I'll just stay on this stock ROM.
darkdevil1 said:
Same. Thanks for your response.
I've rolled back to 2.2 and no Wifi issues so far. I'll just stay on this stock ROM.
Click to expand...
Click to collapse
Which Froyo version do you use? A few times this wifi-bug occured also under Froyo. I'm thinking about going back myself, as Froyo is the only acceptable release to record hiccups-free videos
Hello.
My galaxy s4 4g i9505 is not getting any signal when the phone is locked. When i unlock the phone it gets the signal back to normal
It happens after I installed omega ROM 13.2. I had omega 12 and updated without wiping.
balesss said:
Hello.
My galaxy s4 4g i9505 is not getting any signal when the phone is locked. When i unlock the phone it gets the signal back to normal
It happens after I installed omega ROM 13.2. I had omega 12 and updated without wiping.
Click to expand...
Click to collapse
In Connections/ More Networks/ Mobile Networks/Network Mode choose GSM. You can choose LTE if you want but unless you are in an area that has non-stop LTE coverage, you will face the following bug: when your screen is off, it will lose the networks and stop mobile data. That wont happen when the screen is on and its really fast. So the solution would be to have the GSM option ticked and that way you still have mobile data even with screen off
johar.sanjeev said:
In Connections/ More Networks/ Mobile Networks/Network Mode choose GSM. You can choose LTE if you want but unless you are in an area that has non-stop LTE coverage, you will face the following bug: when your screen is off, it will lose the networks and stop mobile data. That wont happen when the screen is on and its really fast. So the solution would be to have the GSM option ticked and that way you still have mobile data even with screen off
Click to expand...
Click to collapse
Ok, it works, but if I select only GSM I have no 3g connection. And if I select GSM/WCDMA the problem reapears.
balesss said:
Ok, it works, but if I select only GSM I have no 3g connection. And if I select GSM/WCDMA the problem reapears.
Click to expand...
Click to collapse
Flash the MJ5 modem and problem solved
Sent from my GT-I9505 using XDA Premium 4 mobile app
luxubu_dang said:
Flash the MJ5 modem and problem solved
Sent from my GT-I9505 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Didnt worked
I have the same problem when I upgrade from google edition of omegaroms. The Basevand version I'm on is I9505XXUBMF8 and I have tried using the modems in the install guide of 13.2 and nothing works.
now com.android.phone stops working. Can't recieve or make calls.
same here
I have same problem.
Today I update my S4 19505 to JB 4.3 with Kies.
Everything went well, until I locked phone and realize that there is no network signal.
When I chose GSM only everything work.
I am on T-mobile.
What can be a problem.
chemarko said:
I have same problem.
Today I update my S4 19505 to JB 4.3 with Kies.
Everything went well, until I locked phone and realize that there is no network signal.
When I chose GSM only everything work.
I am on T-mobile.
What can be a problem.
Click to expand...
Click to collapse
Please help
chemarko said:
Please help
Click to expand...
Click to collapse
I have the same problem.
I tried all radios and the problem persist.
Everything works fine on google editon, but I have to say that samsung roms are much usable.
Solution:
Do not use roms based on mj7, use roms based on mj5 or go back to 4.2.2
I have tested all radios many kerneles with many mj7 based roms and always had this problem.
With mj5 based roms and rom based on 4.2.2 android everything is alright.
Adam
Adam
johar.sanjeev said:
In Connections/ More Networks/ Mobile Networks/Network Mode choose GSM. You can choose LTE if you want but unless you are in an area that has non-stop LTE coverage, you will face the following bug: when your screen is off, it will lose the networks and stop mobile data. That wont happen when the screen is on and its really fast. So the solution would be to have the GSM option ticked and that way you still have mobile data even with screen off
Click to expand...
Click to collapse
Thank you!! i had the same problem and this fixed it.
RiTCHiE007 said:
Thank you!! i had the same problem and this fixed it.
Click to expand...
Click to collapse
You know that you have the slowest internet available selected? I wouldn't call that fixed.
Lennyz1988 said:
You know that you have the slowest internet available selected? I wouldn't call that fixed.
Click to expand...
Click to collapse
i agree...
i have a device 4.3 baseband I9505XXUAMDC
Same issue here..any proper solution here?
Use STOCK rom
Thanks
Anyone found a proper solution to this yet?
yup
blacknanna said:
Anyone found a proper solution to this yet?
Click to expand...
Click to collapse
Only after i flash this modem with odin I9505XXUEMJ7_MODEM
it finely worked, 3G work fine and no more disconnection
i use GT-I9505_WanamLite.XXUGNG2.V2.9.NO-WIPE rom.
ronzrihen said:
Only after i flash this modem with odin I9505XXUEMJ7_MODEM
it finely worked, 3G work fine and no more disconnection
i use GT-I9505_WanamLite.XXUGNG2.V2.9.NO-WIPE rom.
Click to expand...
Click to collapse
Nop. That doesn't work either. It still drops data connection if you set phone to 4G/3G/2G, and you move with your phone on deep sleep to a low 4G coverage area. It gets connection back as soon as you turn on the screen...
Any other solution so far???
eruyome said:
Nop. That doesn't work either. It still drops data connection if you set phone to 4G/3G/2G, and you move with your phone on deep sleep to a low 4G coverage area. It gets connection back as soon as you turn on the screen...
Any other solution so far???
Click to expand...
Click to collapse
up...
eruyome said:
up...
Click to expand...
Click to collapse
look into build.prop or init.d folder for battery tweaks and delete these
Ghost44 said:
look into build.prop or init.d folder for battery tweaks and delete these
Click to expand...
Click to collapse
I don't have any of those.
I'm having this issue too after updating to the most recent CM nightly. I thought it was the nightly, but after after multiple wipes and even different ROMs, I still seem to have this issue. My mobile network drops as soon as I put the phone to sleep. When I turn on the screen, sometimes it connects automatically, sometimes I have to airplane mode and back. If I change my mobile network to 2G (gsm), it stays connected. Wifi always stays connected it appears.
So I followed the thread and searched the ins and outs of all the comments. I saw issues regarding WiFi, but mine is a little different.
I tried 0.33, 0.48, 0.84, and the 0.84 hybrids just like the posts recommended.
Those radios allowed me to view WiFi networks in my area, except a few. I could connect to my own network... when I could actually see it. Sometimes I would have to disabled and re-enable WiFi several times before I could actually see my connection.
So wifi works, only sometimes. But if I switch back to stock or PA, I see my wifi network without any problems.
I'm starting to think it's not the radio's and may be my network compatibility with MIUI?
I tried Datsuns build and Kings build and they both couldn't keep a solid connection with my wifi network, but still able to see 7 other wifi networks constantly.
Any ideas of what I'm missing?
Thanks in advance
_LANTERN said:
So I followed the thread and searched the ins and outs of all the comments. I saw issues regarding WiFi, but mine is a little different.
I tried 0.33, 0.48, 0.84, and the 0.84 hybrids just like the posts recommended.
Those radios allowed me to view WiFi networks in my area, except a few. I could connect to my own network... when I could actually see it. Sometimes I would have to disabled and re-enable WiFi several times before I could actually see my connection.
So wifi works, only sometimes. But if I switch back to stock or PA, I see my wifi network without any problems.
I'm starting to think it's not the radio's and may be my network compatibility with MIUI?
I tried Datsuns build and Kings build and they both couldn't keep a solid connection with my wifi network, but still able to see 7 other wifi networks constantly.
Any ideas of what I'm missing?
Thanks in advance
Click to expand...
Click to collapse
Flash 4.3 bootloader as well
If you still have issues I don't know.
MameTozhio said:
Flash 4.3 bootloader as well
If you still have issues I don't know.
Click to expand...
Click to collapse
Tried that, same issues.
Going to try to do fresh installs when I get home tonight
I don't know what else to think other than something to be going on with my home network?
For some reason I see my neighbors wifi but not my own. Pretty much driving me nuts.