Related
which uRamdisk to Replace into touchnooter-1.6.24 to make it work on 1.1 is not clear (there are 2 of them).
The answer is ONLY /nooter/boot/uRamdisk (don't touch the one in the root)
with this configuration (and the framework.jar) i got it to work on the first boot, no need to make the 3 boots sequence.
concluding (starting from an 1.1 virgin system):
download touchnooter-1-6-24.zip
extract touchnooter-1-6-24.img
download one of those uRamdisk
download framework.jar
replace ONLY /nooter/boot/uRamdisk in touchnooter-1-6-24.img
replace framework.jar in touchnooter-1-6-24.img
write touchnooter-1-6-24.img on the SD
just 1 boot as usual to the android welcome page,
then remove the SD,
reboot,
double skip as usual
NookColorTools - disable and re-enable non market apps (uncheck and check it again),
Youtube (error 401),
Gmail
and finally...
Market (install at least 1 application with this version, search doesn't work)
now (after you have installed 1 app) eventually replace Vending.apk with this to enable search
i also putted this inside my touchnooter, the 2 .jar into the framework directory and the apk into the app but this shouldn't be necessary...
this is how it worked for me, enjoy
Since i don't have enough posts for development forum, i will post this here, may be someone can move it to the right place, i'm not used to spam, but this 10 posts rule seems to encourage new users to spam 10 posts around...
move it here if you can
I think what you are addressing is exactly apeine's problem:
changed both uramdisk ... Booted with SD in and it either locks up or goes to regular nook (on 12 tries, 10 lock ups and 2 going to regular nook)
Click to expand...
Click to collapse
Incidentally, how long did it take to boot and work on the first try? With 1.0.1 firmware I rooted three nooks and left it for over 30 minutes on the first one without success. Then on the other two I was impatient and gave it two boots. So I never let 1.1.0 go on that long before rebooting since I assumed it was going nowhere.
Kralik said:
I think what you are addressing is exactly apeine's problem:
Click to expand...
Click to collapse
yes, that's why i wrote this, i cannot reply in the development section because i have too few posts on the forum
Kralik said:
Incidentally, how long did it take to boot and work on the first try? With 1.0.1 firmware I rooted three nooks and left it for over 30 minutes on the first one without success. Then on the other two I was impatient and gave it two boots. So I never let 1.1.0 go on that long before rebooting since I assumed it was going nowhere.
Click to expand...
Click to collapse
In my case it took slightly longer than a normal boot, no freeze at all, just about 1-2 minute on "Rooted Forever", then some time, may be 1-2 minutes on the nook dots screen with the dots moving (they never froze) and then the android guy page, no more than 4-5 minutes globally.
Anyway when i used touchnooter on 1.0.1 the first time, i had to reboot 2 times as you reported, same problem, more or less, may be the freezing at boot is something which happens, but not regularly
thank you for the description!
so if i understood correctly, there's no drawback with this method, everything works as it was before upgrade to 1.1.0, including the Market?
what about the installed apps, especially the non-free ones? (I've purchased OrientationControl)
can I simply download it from Market again, or should I backup the APK file and copy it back after upgrade/root?
glezmen said:
thank you for the description!
so if i understood correctly, there's no drawback with this method, everything works as it was before upgrade to 1.1.0, including the Market?
Click to expand...
Click to collapse
Yes, my nook behave exactly as with 1.0.1
glezmen said:
what about the installed apps, especially the non-free ones? (I've purchased OrientationControl)
can I simply download it from Market again, or should I backup the APK file and copy it back after upgrade/root?
Click to expand...
Click to collapse
No idea, never bought an app, just free ones, but to keep an .apk backup is always a safe choice
about orientation... i remember Orientation Switch and this (just in case someone wanted rotation for free)
glezmen said:
what about the installed apps, especially the non-free ones? (I've purchased OrientationControl)
can I simply download it from Market again, or should I backup the APK file and copy it back after upgrade/root?
Click to expand...
Click to collapse
You can re-install purchased apps from Market whenever you want.
Celebom said:
about orientation... i remember Orientation Switch and this (just in case someone wanted rotation for free)
Click to expand...
Click to collapse
thanks for the hint, I will have a look on it (especially if i can't download the app again for free )
btw 1 EUR was not a big pain (I tried ADW launcher and rotation before, but it was not really convenient)
As long as you have market working with your prior GMail account, you should have no problem redownloading both your free and paid apps.
Thanks. Worked like a charm.
I first installed Astro File Manager, which is the second one in the list under the "Productivity" -> "Top Free". This allows me to install Vending.apk (Market where the search function works), and then follow it with Titanium Backup.
Using Titanium Backup re-installed all the apps from my previous backup, plus installed the XorZone's NookTouchTools for 1.1 (jars are different from 1.0.1).
I'm not sure what the significant difference is between the firmwares, but I understanding that the screen refresh is a bit quicker, and that the battery report is more accurate (previously batt reading would fluctuate when first turned on).
As for the firmware upgrade.... my STR just did not want to download the upgrade, even though I set the screensaver to 1 hour. There could be several reason why this didn't work, such that I don't live in US, or the process of rooting had modified something (even thought I factory reset it).
In the end I just connected it using USB, and loaded it into the root directory of the my STR (a simply file copy in Windows XP). Then the upgrade started a minute after the copy.
Thanks for your guide! I've just finished rooting my 1.1 Nook Simple Touch firmware
Remember everybody :
ONLY REPLACE URAMDISK IN NOOTER/BOOT/ (OF TOUCHNOOTER .IMG FILE)
uRamdisk mirror?
Hello, guess I shouldn't have started without all the downloads but I assumed they would be somewhere? any alternative downloads for uRamdisk_rooted because all the links are broken.
Thanks
I want to root my nook simple touch - what works TODAY?
Hi all.
I find this thread interesting and helpful. I have noted that a lot of the information here, on nook developers, or in two articles I read (one in lifehacker.com and the other in Que Publishing) all contain help that includes links to files that are either not there or I can't find.
Can someone point me to a current simple solution that will allow me to root my nook and toggle between the original home screen and the better Android one?
Thanks in advance!
Halfhoff said:
Hi all.
I find this thread interesting and helpful. I have noted that a lot of the information here, on nook developers, or in two articles I read (one in lifehacker.com and the other in Que Publishing) all contain help that includes links to files that are either not there or I can't find.
Can someone point me to a current simple solution that will allow me to root my nook and toggle between the original home screen and the better Android one?
Thanks in advance!
Click to expand...
Click to collapse
ButtonSaviour should have been installed with the Root, so just look for a transparent(translucent?) arrow button thing on the right screen, near the middle. It might be hard to hit it. The Home button on that will be like hitting the Home button on a normal Android device, and when you press the Quick Nav button, the home on that will lead to the B&N home unless you used Xor's mods to change what it leads to.
broken link..........
+1
All the links that I find on the internet for the uRamdisk_rooted file appear broken also...
Markey1979 said:
All the links that I find on the internet for the uRamdisk_rooted file appear broken also...
Click to expand...
Click to collapse
uRamdisk, rooted, adb wireless, fixed init, 1.1 and 1.1.2
http://code.google.com/p/nst-recovery/downloads/detail?name=uRamdisk_wireless_adb_init_1.1_1.1.2.zip
uRamdisk, rooted, adb usb, fixed init, 1.1 and 1.1.2
http://code.google.com/p/nst-recovery/downloads/detail?name=uRamdisk_usb_adb_init_1.1_1.1.2.zip
Hello,
I have just installed CyanogenMod 7 for the Barnes & Noble Nook Color :: V7.0.3 using ClockworkMod Recovery.
After installing CyanogenMod 7, I install the Google Apps addon version: gapps-gb-20110307. The installation goes smoothly, and I receive the "Installation Complete!" message before I remove the MicroSD card and reboot.
Upon reboot from ClockworkMod Recovery, I receive an "Installation Failed" screen that tells me to power on and off the device. I do so, and successfully boot into CyanogenMod7.
I immediately proceed to the Homescreen, where the only items are "Messaging" "Contacts" "Clock" "Email" "Camera" and "Gallery". I have no prompt to set up my Google Account or Timezone. Also, I do not have Market, but I can connect to my WiFi network.
Thank you for your help, it is appreciated. I am obviously a noob, and my apologies for stepping on any toes!
Wow! Looking at some of the questions neighboring mine and their lack of responses, I tend to doubt that mine is going to get answered, even over the long run. I thought this forum had active users, at least that is what the Registration Video said...6 million active users was it???
First of all, deep breath. It may not get answered right away, but typically the questions get answered.
First off, any particular reason you are running 7.0.3? If I recall, this includes the old kernel that has terrible battery life. I would recommend going to 7.1 found here.
I don't know which gapps goes with 7.0.3, but I would double check to make sure it was the right one. I'd still recommend upgrading to 7.1 stable.
Also, I personally recommend doing ROM and GAPPS in two steps... I have eliminated some of the problems I have seen myself by using that method.
1. Install ROM... boot it up... let it settle in.
2. Reboot into CWM and install GAPPS... boot it up... do your thing
Also remember... 4 hours isn't a real long time to wait before posting a second post like you did... especially on a Sunday evening... This is a forum... not an immediate feedback application.
My apologies for my impatience. I did not mean to sound so callous, but after rereading my comment, I realize how abrupt it was.
Also, I remember the site introduction mentioning clicking on the thanks meter as a piece of site etiquette. How do I do that?
After following your advice, I am still having the same problem: not able to use the Android Marketplace as the item is not on my Homescreen, and the Google Apps are not installing.
I took biohazrd's advice, and I upgraded to 7.1 stable.
I also took DizzyDen's advice and installed CyanogenMod 7.1, reboot, let it settle, powered off, booted into Clockwork and installed the google apps pack (gapps-gb-20110828-signed), then rebooted again.
Still, I have no Android Marketplace.
As I stated in my previous post, I am a newbie, and I don't know what I am talking about, but off the top of my head, I have a feeling as if the google apps pack that I used (gapps-gb-20110828-signed) is not the right one. Could this hold any water?
Also, I don't know if it makes any difference, but I bought my Nook in December 2011 and it is a refurbished model. Because I purchased it in 2011, I updated the partitioning scheme using (repartition1GBdata-v1) and (reformatData-v1).
Thanks again, I appreciate the help!
Littlefatman said:
After following your advice, I am still having the same problem: not able to use the Android Marketplace as the item is not on my Homescreen, and the Google Apps are not installing.
I took biohazrd's advice, and I upgraded to 7.1 stable.
I also took DizzyDen's advice and installed CyanogenMod 7.1, reboot, let it settle, powered off, booted into Clockwork and installed the google apps pack (gapps-gb-20110828-signed), then rebooted again.
Still, I have no Android Marketplace.
As I stated in my previous post, I am a newbie, and I don't know what I am talking about, but off the top of my head, I have a feeling as if the google apps pack that I used (gapps-gb-20110828-signed) is not the right one. Could this hold any water?
Also, I don't know if it makes any difference, but I bought my Nook in December 2011 and it is a refurbished model. Because I purchased it in 2011, I updated the partitioning scheme using (repartition1GBdata-v1) and (reformatData-v1).
Thanks again, I appreciate the help!
Click to expand...
Click to collapse
If it isn't on the Homescreen, did you check by open App Drawer?
Thanks for the reply Votinh.
I did not find the Marketplace in the App Drawer. My app drawer currently contains:
Browser, Calculator, Calendar, Camera, Clock, Contacts, Dev Tools, Downloads, DSPManager, Email, File Manager, Gallery, Messaging, Music, Phone, ROM Manager, Search, Settings, Sound Recorder, Spare Parts, Superuser, Terminal Emulator, Theme, Chooser, Videos and Voice Dialer.
I was having a look around and figured out how to look at the Internal storage and found something called Market Apps Installer version 1.1. I click on it, but it offers few options to fiddle with and seemingly no way to access the Android Marketplace.
Again, thanks for your help, I truly do appreciate it!
If it doesn't work as expect, I guess you have to list step by step what you have done up to that point, that may help us pin point where and what you did wrong.
Also, pls clearly indicate where you run the ROM from.
Thanks again for your help, Votinh.
votinh said:
Also, pls clearly indicate where you run the ROM from.
Click to expand...
Click to collapse
I am not sure what you mean. Where can I possibly run the ROM from (what are the possible answers)? I would assume that I could run it only from the SD card. Sorry for being a newbie!
I will list step by step all of my actions and detail them in the response. Maybe, I will go through the whole installation process again and mark down everything that transpires.
Also, what do you think of my theory? That I am downloading and installing the wrong gapps pack?
Littlefatman said:
Also, what do you think of my theory? That I am downloading and installing the wrong gapps pack?
Click to expand...
Click to collapse
gapps-gb-201111028-signed.zip is still on the CM wiki as the latest version... did you verify MD5 checksum and ensure you didn't have a bad download?
Littlefatman said:
Thanks again for your help, Votinh.
I am not sure what you mean. Where can I possibly run the ROM from (what are the possible answers)? I would assume that I could run it only from the SD card. Sorry for being a newbie!
I will list step by step all of my actions and detail them in the response. Maybe, I will go through the whole installation process again and mark down everything that transpires.
Click to expand...
Click to collapse
In here, xda NC forum, you will frequently see the term "eMMC" and "uSD"
eMMC refers to the internal memory of the device, as currently where the B&N stock ROM resides while uSD is the external card where we can put the custom ROMs such CM7/9 in and run from there.
Depends on which method you choose to use, different procedures/instructions needed.
---------- Post added at 09:23 AM ---------- Previous post was at 09:21 AM ----------
Littlefatman said:
Also, what do you think of my theory? That I am downloading and installing the wrong gapps pack?
Click to expand...
Click to collapse
As for your theory, I and we assume that you have installed CORRECTLY and if it isn't working as expect, then we need to know step-by-step how you did.
Everything is possible from bad zip to bad card.
My apologies for the delay in my reply. It has been a hectic week+end.
did you verify MD5 checksum and ensure you didn't have a bad download?
Click to expand...
Click to collapse
I am ashamed to say it, but I do not know how to verify a checksum to ensure the intergrity of a download. Although, I did download the gapps file twice, once each on different computers, copied it to the SD card and attempted to update. Is it possible that I could have gotten 2 bad downloads on 2 different PCs?
I have gone back and redone every bit of my CyanogenMod and Google apps installation on my Nook Color. I have taken notes on it and below is my step by step description of what I have done and observed. My apologies for the book, but I wanted to be as thorough as I could. Thanks for your help and I would appreciate and advice that can help me resolve this unfortunate situation.
1. Downloaded ClockworkModRecovery (2gb_clockwork-0.7.tar.gz) from http://code.google.com/p/monster-rootpack/downloads/detail?name=2gb_clockwork-0.7.tar.gz&can=2&q=
2. Downloaded CyanogenMod 7.1 (update-cm-7.1.0-encore-signed.zip) from here http://download.cyanogenmod.com/?type=stable&device=encore
3. Downloaded Google Apps (gapps-gb-20110828-signed) from here http://wiki.cyanogenmod.com/wiki/Latest_Version/Google_Apps
4. Downloaded Win32DiskImager (win32diskimager-binary) from here https://launchpad.net/win32-image-writer/+download
5. Extracted Win32DiskImager files to a folder on desktop
6. Decompressed and Extracted ClockworkModRecovery to Desktop (this took longer than I expected, the extraction strangely taking 5 minutes)
7. Start up Win32 DiskImager and receive the following File Error message: An error occurred while accessing the device. This usually means something is currently accessing the device; please close all applications and try again. Error 1 Incorrect Function.
8. The File Error message displays itself 3 times. I click OK three times, and then the Win32 Application opens, and I continue with my process.
9. Use Win32 DiskImager to write ClockworkMod onto my MicroSD card. The MicroSD card is a 1 year old, 2GB Transcend MicroSD Card. I use an Kingmax MicroSD card adapter to plug the card into my Computer’s SD card slot.
10. Copy the CyanogenMod 7.1 file and the Gapps 20110828 file to the MicroSD card.
11. Eject the MicroSD card from the PC, insert it into my Nook, and power on.
12. Boot into ClockwordMod Recovery, I go to Mounts and Storage, click on Format System and confirm YES. Next, I format Data and Cache.
13. NOTE: Previously, I was receiving an "Error: can't format /data" error as my newer Nook Color had a different partitioning scheme. I used ‘reformatData-v1’ and ‘repartition1GBdata-v1’ to remedy this when I first attempted to install CyanogenMod. It seems to have gone off without a hitch.
14. I then go to ‘install zip from sdcard’ , the choose ‘choose zip from SD card’ and select the Cyanogenmod 7.1 zip. It opens and installs.
15. After the install completes, I remove the SD card and reboot the Nook.
16. Upon reeboot, I get a Cyanogen loading screen for a few seconds, followed by an error screen that says Install Failed with a large red and white exclamation mark over a Nook clip art.
17. The Nook powers off after a few seconds. I then power on again and sucesssfully boot into Cyanogenmod. I do not have the Marketplace app at this point.
18. I power off, replace the SD card, and boot into Clockworkmod.
19. I choose ‘install zip from sdcard’ and then ‘choose zip from SDcard’ and the gapps zip. I confirm YES and install the gapps zip.
20. I remove the SD card and reboot the system. I receive the exact same ‘Install Failed’ error screen with the red and white exclamation mark over a nook clip art.
21. After a few seconds the nook powers off after the error screen. I power on again and boot into CyanogenMod.
22. There is no Marketplace app on the homescreen or in the App Drawer, leaving me with the same initial problem
Thank you for everything!
I don't think Market will show until you have registered with google. There is a setup wizard or one time provisioning process to go through. That may be the thing that is failing when you first boot. Not sure how to get you back on track.
Sent from my NookColor using Tapatalk
Re: Google Apps Not Installing
Hi,
After you install CM 7.1, Google Apps, and reboot (hard power off and cold boot - the first boot will fail), look for the Google Talk app in your App Drawer and log in to it with your Google credentials. That should spawn the installation of the rest of the Google Apps, including the Android Marketplace.
Also, strangely enough, when installing my first app from the Market, I had to install it with the device physically in landscape mode, as the installation failed when the device was being held in portrait orientation. This seemed to clear up after the first app was installed.
I stumbled across this thread tonight, as I was searching for a solution to this exact problem while updating a friends Nook Color to CM 7.1. This did the trick for me.
Good luck!
Frank
Thank you Frank! I am going to finish up my current task then break out the Nook and cross my fingers that this will work! I will let you know!
I, too, am having problems
I don't mean to thread-jack, but I am also having problems with gapps.
Following this thread: http://forum.xda-developers.com/showthread.php?t=1000957
The version of CM7 I placed on my card is "cm_encore_full-253.zip". The steps all the way through putting that on the card, putting that in the Nook, booting, it all worked fine. I DID notice the line that said something along the lines of looking for the gapps installation, not finding it, and skipping that step.
I downloaded the Gapps ("gapps-gb-20110828-signed.zip") onto my computer. I shut off my NC, took out the SD card, and went to put it into my computer. Lo and behold, my computer can't read the SD card. It tells me it needs to be formatted before it can be used.
Uh. How am I supposed to get anything on the sd card?! I can't even format it to start over - Windows fails to format it.
I tried plugging in my NC to my computer - I at least got the CM7SDCARD to open, but it doesn't appear to be everything (there's no "boot" folder there). I tried moving the zip file to just the main directory of what I saw, and booted into recovery mode, but nothing happened.
Any assistance would be appreciated!
U
caseystain said:
I don't mean to thread-jack, but I am also having problems with gapps.
Following this thread: http://forum.xda-developers.com/showthread.php?t=1000957
The version of CM7 I placed on my card is "cm_encore_full-253.zip". The steps all the way through putting that on the card, putting that in the Nook, booting, it all worked fine. I DID notice the line that said something along the lines of looking for the gapps installation, not finding it, and skipping that step.
I downloaded the Gapps ("gapps-gb-20110828-signed.zip") onto my computer. I shut off my NC, took out the SD card, and went to put it into my computer. Lo and behold, my computer can't read the SD card. It tells me it needs to be formatted before it can be used.
Uh. How am I supposed to get anything on the sd card?! I can't even format it to start over - Windows fails to format it.
I tried plugging in my NC to my computer - I at least got the CM7SDCARD to open, but it doesn't appear to be everything (there's no "boot" folder there). I tried moving the zip file to just the main directory of what I saw, and booted into recovery mode, but nothing happened.
Any assistance would be appreciated!
Click to expand...
Click to collapse
Look at my post here. It tells you how to make the boot partition show up in your system. In your case download the rar rev 1 and follow the directions (per edit 2) on how to manually put the file on your system.
http://forum.xda-developers.com/showthread.php?p=22858059
Edit: You sound like a newby, so in order to do this you need the program "root explorer" which you buy on the market. Very useful program for later use too.
If you don't feel like trying this, get a different card reader or computer to see if that helps reading the card.
Edit 2: Also look here for a more recent nightly that has a few bugs fixed. It was built in January and 253 was in November.
http://forum.xda-developers.com/showthread.php?p=23198390
I bought a used nst glowlight (bnrv350), I made a backup, and then I tried to root using glownooter, but had a limited success : I could not install google market or opera mobile.
So I tried to restore the backup, but after "read forever, your nook is starting up", nothing happens, the message just stays there. I can boot with the back button, but it does the same.
I then tried to restore the factory image several times, using all the methods I could find in the internet, but it does the same as above. It has been going on for 24 hours.
The problem might have originated when I could not use winimage in my windows 10 computer to make the backup, and I used windows xp in a virtualbox in my linux computer instead. I used also dd, but I am afraid I don't remember the exact order. The backup size is 426.8 MB.
I reverted back to windows 10 with win32diskimager, with the same result.
Can anything be done ?
sinlog said:
I bought a used nst glowlight (bnrv350), I made a backup, and then I tried to root using glownooter, but had a limited success : I could not install google market or opera mobile.
So I tried to restore the backup, but after "read forever, your nook is starting up", nothing happens, the message just stays there. I can boot with the back button, but it does the same.
I then tried to restore the factory image several times, using all the methods I could find in the internet, but it does the same as above. It has been going on for 24 hours.
The problem might have originated when I could not use winimage in my windows 10 computer to make the backup, and I used windows xp in a virtualbox in my linux computer instead. I used also dd, but I am afraid I don't remember the exact order. The backup size is 426.8 MB.
I reverted back to windows 10 with win32diskimager, with the same result.
Can anything be done ?
Click to expand...
Click to collapse
That backup is too large, I think. Should be more in the neighborhood of 250 MB? Have you tried the factory re-image where you just see the booting up screen and then hold down the two bottom hardware buttons until you get a prompt?
It's difficult--but not impossible--to damage the factory image unless you've been messing with the partitions. If that method does not get you there, consider making a NookManager card and trying to access the re-image routine from its menu.
Thank you for your reply. I just used nookManager. After 5 seconds, it said the backup was successful, but there was no backup in the card. Similarly, it said that rooting was successful, but when I removed the card, it did the same as before : "starting up..." and it stays there.
Do you have another idea ? I downloaded the 1.2.2 update from the b&n site. Can nookManager install it ?
PS: The nook was already 1.2.2
Yes, I used the two lower buttons trick.
sinlog said:
Thank you for your reply. I just used nookManager. After 5 seconds, it said the backup was successful, but there was no backup in the card. Similarly, it said that rooting was successful, but when I removed the card, it did the same as before : "starting up..." and it stays there.
Do you have another idea ? I downloaded the 1.2.2 update from the b&n site. Can nookManager install it ?
PS: The nook was already 1.2.2
Yes, I used the two lower buttons trick.
Click to expand...
Click to collapse
5 seconds is not enough time for NookManager to correctly make a backup. And, backups can only be seen on the card if you connect your NSTG to your PC while NookManager is running. Otherwise the partition is invisible.
It's hard to know since I have no experience with the NSTG. If it were an NST I would suggest that you perform the region change flash, but it's not clear if that will remove your light function or, indeed, if the flash is deep enough to rewrite the areas of your device that appear to be preventing boot. AFAIK there are no ROM images for the NSTG available. But there might be. Somewhere.
I guess if you have exhausted all the possibilities, rather than trashing the device I would try the region change (just flash the US firmware again--I assume that's what's on there already). It may or may not preserve the glowlight capability, but it might at least produce a functioning e-reader. But only as a last resort.
Edit: Hmm.... seems like I've been down this winding road before: https://forum.xda-developers.com/showpost.php?p=72551413&postcount=57
But I emphasize that this process worked for a plain NST, not the NSTG, so it is an absolute last resort (and might not work anyway because you could have a completely different situation). Next thing is to look at the innards of the 1.1 updater and see if Glowlight updates could be substituted...
O.K. So here is a thread that contains a link to an NSTG image and the instructions to write to your device (read down in the thread).
https://forum.xda-developers.com/showthread.php?t=2608815
What "may" happen: your device could end up with a mismatched serial number and or MAC address depending on how this image was made. There is information on this forum for correcting the MAC address. Just a disclaimer. I don't know. IF this is successful, you can then do a manual update to 1.2.2 and then root with the updated NookManager. I've checked the link to the image and it is still good. I got a file that is about 245 MB--seems about right. Presumably you use the image in place of your backup in the restoring process described in the thread.
I am very grateful for your help, but I am afraid I need more. The nook is now functioning and I might not have done it without your hints. As you suspected, the serial number and mac address have changed (I wrote them down before all this). I suppose that's why it did not automatically upgrade to 1.2.2 . Also the device says it's connected to the internet, but it doesn't seem to be.
I searched xda (nstg mac address, nstg serial number), but I didn't find anything meaningful to me (there are posts by Renate and by ros87 but too complex). Can you help, please ?
sinlog said:
I am very grateful for your help, but I am afraid I need more. The nook is now functioning and I might not have done it without your hints. As you suspected, the serial number and mac address have changed (I wrote them down before all this). I suppose that's why it did not automatically upgrade to 1.2.2 . Also the device says it's connected to the internet, but it doesn't seem to be.
I searched xda (nstg mac address, nstg serial number), but I didn't find anything meaningful to me (there are posts by Renate and by ros87 but too complex). Can you help, please ?
Click to expand...
Click to collapse
Oy.
I didn't think you would act so rashly with all my disclaimers. Well, it's done. I actually don't think the MAC address is a big deal unless you begin to have issues.
Did you actually manage to register? If so then the serial number must not currently be in use and the change you effected was deep enough to pass muster. If not....well battery life is said to be shorter for devices that have skipped registration.
Correcting the MAC address is described (sort of) here: https://forum.xda-developers.com/showthread.php?t=1483600
As far as I can guess it involves editing a hex file. Doable, but maybe not needed. There is no way to correct the serial number. It is heavily encrypted with private keys. Again, if you managed to register then this is all moot.
How are you judging lack of internet connectivity?
I was not given the opportunity to register and I don't care about registration, but I'd like to have connectivity. The link you just gave me is for the ros87's thread that I mentioned, and I don't know how to use it. So I suppose I cannot upgrade to 1.2.2 . Should I root the device ?
PS : ros87's last activity was 2 years ago
EDIT : I copied nook_1_2_update.zip in the device and it was installed. I have now 1.2.2
sinlog said:
I was not given the opportunity to register and I don't care about registration, but I'd like to have connectivity. The link you just gave me is for the ros87's thread that I mentioned, and I don't know how to use it. So I suppose I cannot upgrade to 1.2.2 . Should I root the device ?
PS : ros87's last activity was 2 years ago
EDIT : I copied nook_1_2_update.zip in the device and it was installed. I have now 1.2.2
Click to expand...
Click to collapse
You didn't answer my question about connectivity. Are you not able to make a connection? With only the stock device there is nothing to connect to other than B&N. What does it say about "Owner" in the Settings?
Yes, you should root. Be sure to use the NookManager update or it won't work.
Before we even think about the MAC address issue you need root access and some way to tell if you actually have an internet connection. That means some kind of functioning browser, etc.
Do you still have that weird backup? If so, keep it safe somewhere. You may want that someday.
I tried to download a book and I got this : Unable to download, Internal error...
I can ping the nook from the computer.
I will look into rooting the device in 2 or 3 hours and then post again. I suppose this is what you're referring to :
https://forum.xda-developers.com/nook-touch/development/nst-g-updating-nookmanager-t3873048
Thank you for your patience with me.
sinlog said:
I tried to download a book and I got this : Unable to download, Internal error...
Click to expand...
Click to collapse
There is an entire galaxy of mystery contained in that statement. Download from where? Download with what? Do you have an sdcard inserted for storage?
nmyshkin said:
There is an entire galaxy of mystery contained in that statement. Download from where? Download with what? Do you have an sdcard inserted for storage?
Click to expand...
Click to collapse
I meant to download a book from the home page of the nook, where it says New reads. I am still unrooted and I don't leave an sdcard inserted.
sinlog said:
I meant to download a book from the home page of the nook, where it says New reads. I am still unrooted and I don't leave an sdcard inserted.
Click to expand...
Click to collapse
Hmm... I'm surprised there are any books populating that section at all since the device is not registered. In any case, that is no test of connectivity since without registration the NSTG will spit out all kinds of generic messages about connections and failures if you attempt anything that requires access of B&N servers--like buying/downloading a book (which you can't do unless you are registered).
Rooted with nookManager updated. Opera mobile needs to be reinstalled. I can connect to the computer using es file explorer, so wifi is ok. BUT I can't use nookManager because I can't read the icon labels. I'll restore the backup tomorrow and I will try another rooting method. There are 2 more, I think : tiny and glownooter. Are there others ?
sinlog said:
BUT I can't use nookManager because I can't read the icon labels.
Click to expand...
Click to collapse
? Do you mean ADW Launcher? You can fix the icon label issue in the Settings. As I recall the default font color is white. That needs to be changed to black. The size can also be changed. Depending on what icon style you pick the label will either be on one line or, if longer, on two. LOTS of Settings in ADW. Don't write it off without spending some time working with it.
Sorry, I used glownooter. It's a lot like touchnooter, with which I am familiar. I still have to sign in to my google account and to install opera mobile. I'll be back when finished.
Opera mobile is installed and working. I still can't sign in to google but I can use yalp store and that's good. Thanks again, nmyshkin, you saved my nook glowlight.
Hello, ladies and lads!
Here's a short version of where I'm at: after installing Wondershare' s dr.phone Recovery on my mom's PC and using it on her phone:
its screen won't respond to touch (can't enter SIM card's PIN nor open screen lock)
the On/Off button won't turn off the phone on long press (maybe due to screen lock)
on restart there's a yellow text that reads "Set Warranty Bit : kernel"
the physical buttons still work
I can see the phone's files and folders only through PC's command prompt, using ADB ('This PC\Galaxy Grand Prime' folder in Win Explorer says it's empty).
Ideally I want to keep her data (FB Messenger, Skype, Chrome, WiFi passwords, etc), and her phone to function again. What do you think I should do?
I think I need an advice and suggestions from someone more experienced than me - I don't even know trusted sites where to download the firmware roms from.
The phone's details are (I'm afraid you'll have to walk me through to get more details to this list, as I'm new to the forum):
Phone: Samsung Grand Prime
Model name: SM-G530FZ
Firmware version: G530FZXXS1BQC2 (Android 5.0.2 with Baltic bloatware, I guess)
Now in detail:
My knowledge and experience regarding the smartphone software & restoration is very basic (I've only restored the firmware to a LG-L70 once some years ago, and that's it).
Before the problem I lost some over 600 media files from that phone by Cutting and Pasting a folder from phone's internal SD to PC's disc. Now I learned never to Cut-Paste important or irreplaceable files. The files ended up on the phone, because a folder with over 800 files couldn't be uploaded to the Google Drive (the camera's folder had over 1k files in it, so I moved some of them to another folder, which the phone created on the internal partition rather than the SD Card, where the original folder was from).
Instead of using a trusted software, I foolishly Googled a photo recovery program for phones, using my mom's PC. A list of bogus recovery program sites appeared (had to look them up on her PC, as I found only legit, widely trusted programs now, using my laptop. Those darn Google's personalized search result algorithms!).
Before using the dr.fone Recovery software I synced most of the data to her account.
Used the "free" dr.fone Recovery software as per its site's instructions, the phone did a restart and the touchscreen went unresponsive to touch. Later the software showed the lost files it found, and offered to restore them for a sum. Naturally I declined.
The software said that to return the phone to normal I need to disconnect the USB cable. I did so, but the phone's screen remained unresponsive to touch, even after restart (long-press [Pow] + [Vol-]).
I tried connecting an USB mouse via the dongle, but the mouse cursor didn't appear (maybe this phone doesn't have this functionality).
Now, after using that FAIL-covery program, I was overly cautious not to make things even worse.
I wanted to make a copy of the phone's internal SD state (or is it called a phone's hard drive?), to get the media files from the clone and to have a backup of mom's files.
But I failed: I downloaded APK, ncat, KingoRoot and BusyBox. Tried to follow the steps in this video: youtu[dot]be/KKkvkCgMeMA. Got stuck at "busybox not found" at about 10:27 mark in that video ("dd if=/dev/block/mmcblk0" "busybox nc -l -p 8888"). Turns out you need to run some of the apps from that phone prior to that step, and I don't know any workarounds.
Then I remembered that the files were on the external SD in the first place. Well duh! I then connected the Micro SD card to PC's reader via a Micro SD adapter. To make a copy of the SD card's 1s & 0s, and to restore the media files from said copy I used ZAR (Zero Assumption Recovery) z-a-recovery[dot]com/. The backup creation (an .ISO file or some such) and media recovery are free of charge.
Now I only need to remove duplicates and blurry pics (I think I had a Moleskinsoft's Clone Remover from an old PC magazine's CD lying around somewhere for the latter). Oh, and I better not forget to run a malware scanner on her PC and remove the mr.fone installed services and folders from it. Went a bit off-topic here, sorry!
Last I pulled a wifi passwords file with "adb pull /data/misc/wifi/wpa_supplicant.conf" command as per instructions on this page: mashtips[dot]com/see-wifi-password-android/. I don't know whether putting the file back on that phone will do the trick or not.
That's pretty much all.
I hope the situation can be resolved and I appreciate your input! :fingers-crossed: Maybe someone has come across a similar post, has constructive commentary or knows something obvious that I haven't come up with? Thank you in advance!
Edit 30 Jan '19: Got the phone working. Accessed the phone with a Chrome browser extension (name here). All accounts except some mail account were gone. WiFi didn't work.
Found a stock ROM here: (address here).
Found the Odin3 tool here: (address here). It came with a different locale ROM.
Flashed the 1st ROM with Odin. The screen started to work.
Flashed the 1st ROM with Odin again. The WiFi started working.
I'll update this with links soon.
I've got the exact same problem after using Dr Fone app!
Hi there.
I've got the same problem with my Samsung Galaxy Grand Prime after using Dr Fone, like you. I contacted Wondershare website from which I downloaded the app but they haven't bothered replying. Not happy at all!!
I contacted Samsung's support team and after trying different things (the usual stuff: reboot; remove the battery and SIM card; restart in Safe Mode; etc) which didn't solve the problem, they ended up telling me to reset the phone to the factory settings but that didn't work either.
Now my phone is stuck on the Samsung Galaxy Welcome screen which asks me to choose the language I want on my phone. The touchscreen is still unresponsive.
How did you manage to fix the problem if the touchscreen was unresponsive?
Thanks in advance for your help!
Your-Mum said:
Hello, ladies and lads!
Here's a short version of where I'm at: after installing Wondershare' s dr.phone Recovery on my mom's PC and using it on her phone:
its screen won't respond to touch (can't enter SIM card's PIN nor open screen lock)
the On/Off button won't turn off the phone on long press (maybe due to screen lock)
on restart there's a yellow text that reads "Set Warranty Bit : kernel"
the physical buttons still work
I can see the phone's files and folders only through PC's command prompt, using ADB ('This PC\Galaxy Grand Prime' folder in Win Explorer says it's empty).
Ideally I want to keep her data (FB Messenger, Skype, Chrome, WiFi passwords, etc), and her phone to function again. What do you think I should do?
I think I need an advice and suggestions from someone more experienced than me - I don't even know trusted sites where to download the firmware roms from.
The phone's details are (I'm afraid you'll have to walk me through to get more details to this list, as I'm new to the forum):
Phone: Samsung Grand Prime
Model name: SM-G530FZ
Firmware version: G530FZXXS1BQC2 (Android 5.0.2 with Baltic bloatware, I guess)
Now in detail:
My knowledge and experience regarding the smartphone software & restoration is very basic (I've only restored the firmware to a LG-L70 once some years ago, and that's it).
Before the problem I lost some over 600 media files from that phone by Cutting and Pasting a folder from phone's internal SD to PC's disc. Now I learned never to Cut-Paste important or irreplaceable files. The files ended up on the phone, because a folder with over 800 files couldn't be uploaded to the Google Drive (the camera's folder had over 1k files in it, so I moved some of them to another folder, which the phone created on the internal partition rather than the SD Card, where the original folder was from).
Instead of using a trusted software, I foolishly Googled a photo recovery program for phones, using my mom's PC. A list of bogus recovery program sites appeared (had to look them up on her PC, as I found only legit, widely trusted programs now, using my laptop. Those darn Google's personalized search result algorithms!).
Before using the dr.fone Recovery software I synced most of the data to her account.
Used the "free" dr.fone Recovery software as per its site's instructions, the phone did a restart and the touchscreen went unresponsive to touch. Later the software showed the lost files it found, and offered to restore them for a sum. Naturally I declined.
The software said that to return the phone to normal I need to disconnect the USB cable. I did so, but the phone's screen remained unresponsive to touch, even after restart (long-press [Pow] + [Vol-]).
I tried connecting an USB mouse via the dongle, but the mouse cursor didn't appear (maybe this phone doesn't have this functionality).
Now, after using that FAIL-covery program, I was overly cautious not to make things even worse.
I wanted to make a copy of the phone's internal SD state (or is it called a phone's hard drive?), to get the media files from the clone and to have a backup of mom's files.
But I failed: I downloaded APK, ncat, KingoRoot and BusyBox. Tried to follow the steps in this video: youtu[dot]be/KKkvkCgMeMA. Got stuck at "busybox not found" at about 10:27 mark in that video ("dd if=/dev/block/mmcblk0" "busybox nc -l -p 8888"). Turns out you need to run some of the apps from that phone prior to that step, and I don't know any workarounds.
Then I remembered that the files were on the external SD in the first place. Well duh! I then connected the Micro SD card to PC's reader via a Micro SD adapter. To make a copy of the SD card's 1s & 0s, and to restore the media files from said copy I used ZAR (Zero Assumption Recovery) z-a-recovery[dot]com/. The backup creation (an .ISO file or some such) and media recovery are free of charge.
Now I only need to remove duplicates and blurry pics (I think I had a Moleskinsoft's Clone Remover from an old PC magazine's CD lying around somewhere for the latter). Oh, and I better not forget to run a malware scanner on her PC and remove the mr.fone installed services and folders from it. Went a bit off-topic here, sorry!
Last I pulled a wifi passwords file with "adb pull /data/misc/wifi/wpa_supplicant.conf" command as per instructions on this page: mashtips[dot]com/see-wifi-password-android/. I don't know whether putting the file back on that phone will do the trick or not.
That's pretty much all.
I hope the situation can be resolved and I appreciate your input! :fingers-crossed: Maybe someone has come across a similar post, has constructive commentary or knows something obvious that I haven't come up with? Thank you in advance!
Edit 30 Jan '19: Got the phone working. Accessed the phone with a Chrome browser extension (name here). All accounts except some mail account were gone. WiFi didn't work.
Found a stock ROM here: (address here).
Found the Odin3 tool here: (address here). It came with a different locale ROM.
Flashed the 1st ROM with Odin. The screen started to work.
Flashed the 1st ROM with Odin again. The WiFi started working.
I'll update this with links soon.
Click to expand...
Click to collapse
cacerts.bks file updated 12-6-20
On May 30, 2020 another certificate in our ancient cacerts.bks file expired. This was one of the certificates used by FBReader to sync with a Google Drive directory of your designation (see books.fbreader.org). I'm assuming at this point that it was the critical certificate in the link because not long ago it was possible to work around login issues as described in my earlier post here: https://forum.xda-developers.com/nook-touch/general/setting-sync-fbreader-t3957311
I was contacted by another XDA member about this issue and noticed in a logcat that the certificate had expired. I have never had any luck updating certificates, despite the description of the process by XDA member @tshoulihane. It took many a year for the basics to penetrate my thick skull and I finally decided to look at it again. I will prepare a post on this topic in a bit so the information won't die with me
Meanwhile, I have updated both certificates in a cacerts file I extracted from a Honeycomb ROM and have been using on all my NST devices. It also includes the updated Amazon certificate so the Kindle app still functions. It contains many more certificates than the file that came with the NST (some expired). At least now I see a way forward.
To update your file, download the zip below and extract the cacerts.bks file. Transfer to the SD card of your NST and then use a file manager with root privelages to copy it into /system/etc/security, overwriting the file that is already there. If you feel queasy about this, first rename the old cacerts.bks file to cacerts.bak, then move the new one in place. File permissions should be rw-r-r
Reboot.
No need for the workaround I wrote about in the earlier post now. I tried this with both Opera Mobile and Opera Mini, signed in on both browsers before starting. Opera Mini failed. Opera Mobile, with the appropriate settings for TLS 1.2 etc. as I have described in another post, balked a little but succeeded. And once you are signed in, you never need to go back to the browser (I think).
Here's what may happen:
1. You may sail through the sign-in process from FBReader (Network Library>FBReader book network) and see your file information appear. Done.
2. More likely than not you will get an "unable to establish a secure connection" or similar. This is a sadly common occurrence in Opera Mobile these days and has been roundly trounced on old Opera discussion boards. There appears to be no fix for it except to access the "Settings" window (from the "O" button). Then go to "Privacy" and then "Clear cache". Now back out of the Settings windows (Back button) and finally hit the "refresh" icon. Voila. This is a general "fix" for pages which don't want to load properly even though you have a valid certificate. I've tried running a script to delete the Opera cache before opening Opera but to no avail. Sometimes you are lucky (especially if you have not encountered any errors in a session before exiting), sometimes you are not. Like I say, once you get past this with FBReader, you should not need to go through it again. Just remember, you want to be signed in with your email, etc. on the Google homepage (the same account for your Google drive you set up with FBReader) before you go through all this.
I tested this with FW 1.2.2, but not 1.2.1
Hello!
Thanks a lot for this information, I was struggling with exactly this yesterday and came here to post this issue, but you already have a solution.
I installed Opera Mini v7.6.4 but couldn't connect to FBReader, so I tried to use the default browser and voilà. Now it's working again.
Thanks again, I really thought it was impossible to fix lol.
I haven't checked if kindle app is working, but it surely does.
Thank you!
How does one install or enable a file manager with root access? I've been googling for hours now and it's such a broad topic that I just can't for the life of me figure it out
xrupa said:
How does one install or enable a file manager with root access? I've been googling for hours now and it's such a broad topic that I just can't for the life of me figure it out
Click to expand...
Click to collapse
If your device is rooted, then you just need a "good" file manager. The version of ES File Explorer I use has an option for enabling root access. Attached.
Ah, that's the release version I have installed, I'll try and find the option, couldn't spot it earlier but that gives me hope
many thanks
Cheers, that's got me on a step or two, I think I just need to disable two step verification next as opera or the standard browser is repeatedly doing the 'failed connection' thing you mention at that stage, lightly infuriating, but at least I'm getting closer to getting my fbreader library back, many thanks!
xrupa said:
Cheers, that's got me on a step or two, I think I just need to disable two step verification next as opera or the standard browser is repeatedly doing the 'failed connection' thing you mention at that stage, lightly infuriating, but at least I'm getting closer to getting my fbreader library back, many thanks!
Click to expand...
Click to collapse
The stock browser is useless. For Opera Mobile don't neglect to make the TLS 1.2 change and, of course, update cacerts.bks
Ah great thanks, I've found that TLS thread, I'll do that and hopefully that'll be it!
nice one @nmyshkin
OMG It's done, im back into the network library on my ancient nook!
thanks so much, months of trying allsorts, nice one, thank you!