[HELP] Stuck screw\nut, can't get it out! - Galaxy S I9000 General

Hi.
I replaced my screen, then I lost my radio signal. So I wanted to open the phone again to check what went wrong.
I lost some of the original screws, so I got some "hex screws" (I don't know what they're called). Anyway, the heads worn out!
I have two left, in the most unlucky positions! Top two corners (if anyone knows what that looks like in an I9000!).
So, Anyone got any ideas how to get those out.
Thanks.

OK, so I have been drilling my phone for the last half hour or less. With absolutely no luck. lol
Please advise.

A grinder might work only joking you need to buy a left hand drill bit it spins in the other way so removes screws

you can buy a bit that removes screws with worn heads, have a search on google
http://www.google.co.uk/products/ca...=f1_LTr70B4OXhQfrycHeDQ&sqi=2&ved=0CHYQ8wIwAQ

You may find that you are able to force in the next size TORX (star shaped) driver, or even use a dab of epoxy glue to glue a hex drive, TORX or even a straight bit screwdriver into place to give enough purchase to get them out and replace them.
Phil

Thank you everyone. Problem fixed.

Related

dismantling O2 Atom housing

Hi,
I have just bought a new O2 atom housing (as my old one is scratched to death), and am currently trying to find a guide or instructions on how to dismantle the phone housing.
I know there are two T screws with void stickers on them that need to be removed at the bottom end of the phone one you slide the battery cover off. I can't see any other screws visible. Apparently there are meant to be 4.
Does anyone have detailed instructions on how to change the housing? I have searched this forum and google, and have come up with nothing much.
Thanks everyone!
There is a fully descriptive video on dismantling the Atom, I cant find it but I had it last year and Im sure you will find it just keep looking. Basically you must remove the camera housing cover and there are two more screws under that, then you run you finger nail between the front and back cover to open the housing, good luck and remember nothing needs to be forced.
try this...http://bible.younet.com/files/2007/03/30/369427.shtml
you have to pop the top half of the rear cover off. it is particularly difficult, and the black strip that runs right around the devices is very soft plastic which gets mashed real easy. try using your fingernail (even that will dent it) and run it around the edge. Once it pops off you will see the other two screws. they also has void stickers on them.
Good luck
this more details http://bbs.pdafans.com/thread-322511-1-1.html
I know there are 4 screws that need to be removed. have taken the top cover off so can see the other 2 screws have an old nokia T tool but it does seem to fit the screw heads
can anybody tell me... what sort of tool do you use to take the screws out?
hmm i use a precision screwdriver set , try all the size and see which one it fits =)
palah said:
I know there are 4 screws that need to be removed. have taken the top cover off so can see the other 2 screws have an old nokia T tool but it does seem to fit the screw heads
can anybody tell me... what sort of tool do you use to take the screws out?
Click to expand...
Click to collapse
be careful with a small plain screwdriver, you'll be ok
i tried dismantling it.. but my objective was to actually remove the camera. couldnt find a way to remove it.. is it possible?
Hi all,
do you know if a Atom Exec housing is compatible with a Xda Atom "classic". Same dimensions i think.
Thanks a lot !

Keyboard is getting too loose!

Hi,
just another question by a lam3 user
After some day using my tytn, i noticed that the keyboard is very loose, just after locking it under the lcd.
to explain better: video
http://www.youtube.com/watch?v=Pj56htWOHEk
as you see, the keyboard is very loose just after locking it.
My device id is 640, so it is affected by some keyboard sliding problems(is a v1605)...but my question is: There is something i can do to fix this?
i tried to tighten the screws i signed here
but without significative improvement.
this is a minor issue,i think, but if i can fix it my tytn will go better in my huge hands
however, no problem if the fixing procedure involves to remove the warranty sticker up the screw, the tytn is on italy and i do not think that vodafone uk will change it
many many thanks
gtazok
The screws you've tightened are just for the housing. To make the keyboard tighter, you need to take the device apart
These 2 links explain everything you need:
http://michael-channon.spaces.live....BlogPart&_c02_owner=1&partqs=cat=Hermes+Fixes
http://www.howardforums.com/showpost.php?p=9119842&postcount=1
Good luck!
underneath your main board is 4 screws tighten those and you should be set. If not you may need to by a new housing. I hope the tighten helps though.
omg, this will really need to open all the device!
damn, there is no other way?
I couldn't really tell from your video if it is the standard loose keyboard problem you've got, but my keyboard was loose in the way that when closed it could 'fall' open pretty easily.
I used the guides above, and while it does invalidate your warranty (unless you're able to remove the warranty sticker without breaking it), it is very easy to do and put back together.
my problem is, as shown on video:
when i try to press the power button, i apply some force to my forefinger to tighten the grabbing around the phone.
when i apply this force, the upper part of the phone(the part where is the buttons of mail and iexplore) slide off the housing, and go for about 2 mm (as shown in the video).
i will like to tightnen this, to do that the phone will never slide the keyb without apply *Decent* pressure.
the keyboard,however, stay solid when fully opened, and *decent* pressure is needed to restore it from the full opening to housing closed.
was i *almost* clear? i'm very sorry but i understand that my english is a mess and really confusing, but if someone could guide me, i can do photo, pictures and so on.
thanks
gtazok
Yep, that sounds exactly the same as my problem!
The 2 links above should help, as long as you're happy to take the phone apart. If you are willing, it is pretty easy to do, but will invalidate your warranty if you still have one.
A couple of taps on the indents on the sliders with a screwdriver will make the sliders much tighter, and you can test the tightness before putting it back together.
I went a bit overboard with mine and overtightened it, but now I prefer it that way -there's no way the keyboard will slide out without some effort
StarMonkee said:
Yep, that sounds exactly the same as my problem!
The 2 links above should help, as long as you're happy to take the phone apart. If you are willing, it is pretty easy to do, but will invalidate your warranty if you still have one.
A couple of taps on the indents on the sliders with a screwdriver will make the sliders much tighter, and you can test the tightness before putting it back together.
I went a bit overboard with mine and overtightened it, but now I prefer it that way -there's no way the keyboard will slide out without some effort
Click to expand...
Click to collapse
great, that was exactly was i searched so!
but..a couple of taps...i have noticed that the indents are "stamped", there is the possibility i will break it with too much force?
and, for opening the tytn, where i can find all the needed in one pack? i live in italy, but i have no idea of what screwdriver and things must(and where)buy.
maybe there is some omnicomprensive pack that could be shipped to italy without problem.
many thanks, i appreciate much
Gtazok
The metal is quite soft in the sliders so it is possible to hit it too hard, but I don't think you're likely to do that if you start softly and keep testing the slider tightness until it's right.
The only 'special' screws are the ones holding the case in, but they can be opened pretty easily with a small flat screwdriver. From what I can remember, the screws inside the phone are just small normal screws.
gtazok said:
omg, this will really need to open all the device!
damn, there is no other way?
Click to expand...
Click to collapse
Okay If you do tighten those screws it will help that. I've seen them to be soo bad that if you tilt the device it slides open. Soo basically if you still under warranty send it to your provider other wise follow this guide.
ftp://ftp.xda-developers.com/Uploads/Hermes/Hermes_Manual_Hyins/Hermes_Service_Manual.pdf
This will guide you through the entire process of taking apart your Hermes. Good luck if you have any questions.
[email protected]
HI!!
just managed to re-close my hermes (first time i closed it without inserting the last cable LOL...i forgot it, but before powering off he comed to my mind..omg what i have risked not plugging last cable before closing??)
however, i did manage do disassembly only with a standard little screwdriver, not without problems
i just arrived to disassemble the keyb, and get rid on the rails.
I must admit that i NEVER have seen so much dust in a phone(i think mine was re-assembled from another).
i have extracted the rails, the 2, and tried to gentle tapping the indents.No way to go, i tapped *gently*(sometimes a little hard) but i really noticed no improvement
so,i thinked:
"if i change the rails, i will have a perfectly mirrored situation, with the keyboard closed it will be ok, with keyb opened it will be a little loose"
(remember, the keyb was loose when try to open it, not when to close)
So i changed the rails, switching them...
and now it's really better, the phone rarely go off his housing, closed, and go down a little more easily(but is acceptable, because i never do any "forcing" when it's open..)
maybe, with time, the opening will become a problem, with the keyb sliding to close when it's open.
However, maybe this not occour.So for now i'm happy
last thing. I noticed that on the page where the man tried to adjust the rails, he suggested
1)to tap the indents( tried, work very very little)
2)to insert pieces of ribbon
i not tried the second suggestion, because i have not understand WHERE to insert those pieces.Maybe he was suggesting to insert them at the end of the rails? where the carts block? if it is, why? i tried to pull up the small piece of "sheet"(i don't know if it's the correct term, sorry for my bad english ) on the border of the cart where it don't block, but whitout results..so inserting ribbon what improvement would have done?
thanks for the patience to read all my messed up english and many thanks
gtaz
the sliders are becoming loose as the beginning.
someone knows where to buy the sliders as a spare parts?
anyone know?
ok no way?
gtazok said:
anyone know?
Click to expand...
Click to collapse
Take a look in this thread & mikechannon's link; if not there, then just pm / ask mikechannon...
http://forum.xda-developers.com/showthread.php?t=298784
galaxys said:
Take a look in this thread & mikechannon's link; if not there, then just pm / ask mikechannon...
http://forum.xda-developers.com/showthread.php?t=298784
Click to expand...
Click to collapse
thanks
gtazok said:
the sliders are becoming loose as the beginning.
someone knows where to buy the sliders as a spare parts?
Click to expand...
Click to collapse
I think you just need to increase those indents a bit more than you did. It is more successful to tap the indents using a small flat blade screwdriver and a small hammer. (Go easy of course and keep testing as you tap. You want a very firm click into place. You should hear the click and it should be really quite hard to move the slider over the indents using your finger tips)
The tapping technique is probably better than just pressing a screwdriver blade onto the indent. Pressing rather than tapping is likely to simply bend the entire metal strip and curve it slightly. This might improve the grip for a while but as the curve gradually straightens out again the slider will just become loose again. Using the tapping method I did mine well over a year ago and I have never had to redo it and it takes a very firm push an audibl clicks to open the device.
(Buying new sliders will not solve your problem. The vast majority, it seems to me were made withy too shallow indents. It may be worth buying new ones if the micro welds have sprung apart however)
Mike
hi
i dismantled my hermes one more time. This time i put out an hammer(a big hammer,indeed)so i "gently" hammered with a flat screwdriver the indents.
result? the keyb is now "really locked" when i open it..but the opening problem remain.
when i try to open it when it is closed, with my finger, i notice that the slipping of the upper left part(seeing the phone from the front) is EVER too loose, i reopened 2 times and tapped "not so gently" the incriminated indent, but i noticed no result. i also tried to exchange the sliders (the lower with the higher) but no improvement was done.
i think that is a defective implementation, because the "centre of pressure" is located in the upper part of the phone, so the phone is like to open more easily when it is closed. Did anyone noticed that?
however, the overall is increased, i think, about 30-40% more tighten as before, and that is no bad.
shame it has no solved my problem, but life it so bad that i can will be live happy with a little loose tytn
thanks
Gtazok
I agree that my the upper left keyboard slider has always been looser than the bottom...
good, that confirm my idea.
let us know if any other noticed the same thing.
thanks
gtazok

Overlapping Sliding Case

Hello,
Recently whenever i close my case on the vx6800 it overlaps now. When its open and i look at it from the back i notice that there are two metal like pins that also move with the opening and the closing. Has anybody had any experience with this problem? Its a minor problem but VERY offsetting.
when i had an issue with overlapping i found out it was one of the stoppers. Basically if you look at the tracks the phone slides along there is two little metal pins on each one that stop it from going so far. the plastic had broken and the piece had fallen out, resulting in the overlap. my phone was less than 3 months old so i took it in for warranty. my quick fix while i was waiting to take it in was hot glue gun. i put a dab in then took an exacto knife and trimmed it down.
Yep, sounds like a rubber bumper fell out if it is a very slight overlap.
Thank you for the replies. I'm going to try a quick fix because i really do not wnat to go through the hassle to downgrade SPL to undo my ROM to turn it in. I guess I'll see this through. I'll post my results if any

How difficult is to take apart an HTC Ozone?

Hi all,
My wife spilled a glass of beer on my PDA, and now the top front buttons don't react like before. Sometimes you don't hear the 'click' and you can feel like they got stuck.
The keyboard looks fine, so the problem is only the with the top buttons at the front of the PDA.
Have anybody tried to take apart this PDA? Would be easy to open it and clean everything before putting everything back?
Thanks a lot
I completely soaked my Ozone about a week after I got it... knocked it in the sink. I like to think that I was among the first to void my warranty, Lo..l?
The phone is really well constructed for what you need to do. All of the critical electronics are very well shielded on the board, nothing difficult about separating the board from the case.
Six 'star drive' screws on the case (that's where the warranty sticker is), one tiny phillips on the board - board pulls up off of pins, away from the usb connector and Bob's your uncle. The keypad is not fastened to the case, pull it right out.
Watch the ribbon cable for the lcd - I would not recommend disconnecting it. there should be enough play to allow you to work. Make sure you're working in a really clean environment, and check the inside of the plastic lcd cover obsessively right before reassembly. If you're anything like me that one little catpet fiber or cat hair or whatever the hell will drive you to take the phone apart again 4 days later...
Sorry about the ramble... it's late. Short answer is: Nothing to it.
Good luck!
Thanks a lot for your post. It was really helpful.
I will probably try it this weekend.
I'll post here the results
Cheers
So if I wanted to buy a different color keypad (dont like the green) it shouldnt be hard to take apart??...I change screens in Env/Voyagers a bit so have a little knowledge...

Looking for screws!

I've been searching high and low for replacement screws for my case. I recently moved and in the move managed to lose the screws I had in supply from a friends busted tilt. I believe they were T6? I'm also needing the spine screws that hold the top panel to the keyboard panel (I think they were small philips head.)
If anyone can give me an idea on where to go either locally or online to purchase fitting screws for my device I would greatly appreciate it!
I have a broken Tilt, the screws are present-no one wants to buy the Tilt (it's water damaged), but you are welcome to the screws for a few bucks...
Still on the hunt for some screws, if anyone can help!
Found out from the service manual that the screw I need is Screw,M1.4,L2.3,(D3.5*H0.2),Kaiser
I'm out looking for micro screws that fit the dimensions, and if I can't find them I may have to resort to some home brew soldering and rigging.
I now have a small bag of screws available from Kaiser...please PM me with the exact type of screw you need and I'll send you pictures and we can see if it's the right thing.

Categories

Resources