Database Users

ALL WIZARD USERS-do u all face the problm nd how u resolve it

hello wizard lovers....iam currently using t-mobile vario just same as imate kjam.i love using this handset,but the one and only problem iam facing is the--LOOSE SLIDER PROBLEM.mine i 6-8 months old,but from last 5-10 days i had observed tht slider has got too loose,nd in the keyboard closed position the gap beetween the upper slider nd lower is also gone big.now here in india one technician tells me he can resolve it by tightening some screws after disassembling it,i just want to inquire from u guys tht is it reaaly possible or he is faking,coz i had searched some previous threads nd noone actually came to a final result,so plz help me nd if possible then add the solution in wizard wiki as well.t nks in advance

Tightening the screws will fix the loose slider issue. And you do have to remove the motherboard to get to the screws.

I had that issue.
look up the wizard service manual in Google or Prodigy service manual.
I took my phone apart.
I inspected it.
Saw the broken piece of plastic inside the phone that has a stop for the bevel on the stylus.
GLUED THAT PIECE WITH EPOXY
Took a foam earplug and cut it (after compressing it) to fit the gap between the stopper and the body of the phone. (to make a spring)
put he phone back together. no problems since march.

Wouldn't that be a fix if your stylus wouldn't stay in? I think mayur9890 is saying the phone is coming apart when he slides the keyboard out.

Definatly the cuase of a loose screw or broke part, its nessesary to take appart to gain access to the screws that hold the slider part together, its fairly simple procedure. Should only take 10 minutes (be carefull not to loose the screws there very small and fidgity)

You could probably do the repair yourself, using one of these manuals: http://forum.xda-developers.com/showthread.php?t=244446

Looking for screws!

I've been searching high and low for replacement screws for my case. I recently moved and in the move managed to lose the screws I had in supply from a friends busted tilt. I believe they were T6? I'm also needing the spine screws that hold the top panel to the keyboard panel (I think they were small philips head.)
If anyone can give me an idea on where to go either locally or online to purchase fitting screws for my device I would greatly appreciate it!

I have a broken Tilt, the screws are present-no one wants to buy the Tilt (it's water damaged), but you are welcome to the screws for a few bucks...

Still on the hunt for some screws, if anyone can help!

Found out from the service manual that the screw I need is Screw,M1.4,L2.3,(D3.5*H0.2),Kaiser
I'm out looking for micro screws that fit the dimensions, and if I can't find them I may have to resort to some home brew soldering and rigging.

I now have a small bag of screws available from Kaiser...please PM me with the exact type of screw you need and I'll send you pictures and we can see if it's the right thing.

Broken Digitizer Help

Hi
I damaged my digitizer on my Touch2, I have ordered a replacement part and it has arrived.
I have stripped the phone down now, but I am stuck as to how to get the screen out.
I don't want to use too much force so any pointers as to how I can get my screen out and replace the digitizer will be greatly appreciated.
Paul

Dude, the only thing i got in my mind is youtube, there you can find anything. Try writing the something like Change digitizer on HTC Touch2 and may be you will find it, good luck

I've looked on u-Tube and found nothing for the Touch 2.
Was hoping someone on here might have more information.

Still no luck on this. Anyone?

I replaced many digitizers on blueangel and always used razor blade to seperate the lcd frame from the digitiser. The only issue was soldering the digitiser in to the lcd ribbon cable as they are soooooo thin, never opened the touch 2 yet but I can imagine its probably all cramped in there

I successfully changed my digitalizer.
I used book to help myself with added book.
Code:
www[dot]mikechannon[dot]net/PDF%20Manuals/OSeven%27s%20Disassembly%20Guide%20to%20the%20HTC%20Touch%20-%20Elf%20.pdf
Firstly, remember what you do, photograph your phones "guts" if you wnat
I, like in other video tutorials, started with removing 4 screws, after that gently half-opened corner gap between silver and front side and put in that gap plastic thing which came with digitizer.
When successfully lifted back off then you gonna see main board. In top right corner there is little screw which comes out hard in my situation. An you have to take off LCD connector wire (in left side) and digitizer connector (in left top corner). Don't forget after change of digitizer to put them back like they were or you will have to disassamble again !!!!
After doing that GENLEY lift main board off of screen. BE CAREFUL. YOU Have to pull of that black sticker on right side on board which connects from volume control to main board. Don't forget to put it back.
So you have the front side on your hand. Now push gentley but hard it from inside out. It is glued with some kind of glue. It seems it won't come but it comes (in that book it is showed).
So change your digitizer to new one and put everything back together.
You are done. Sorry I don't have pictures because it didn't came in my mind to picture it
I hope this tutorial will help you.

This is not for the Touch 2 but thanks for the help.
Still nto replaced it yet, phone is in bits in a box.

http://www.pdacenter.ru/razborka/htc_touch2_t3333/
Tutorial is in Russian.Just look at the pictures.
greetings

not sure
Sent from my generic using the XDA mobile application powered by Tapatalk

[Q] Epic Disassembly - How can I open it up?

I'm on my 3rd Epic, and this one is going back, too.
Before I send it back, I'd like to disassemble it. I think that the current problem (speakerphone returns static to whoever I talk to) is a soldering issue and may be easily debugged and fixed if I could open up the phone.
Opening up this guy is not easy.
I can remove the visible screws.
I can remove the two screws hidden under the serial number sticker / battery mat.
Even after removing these screws, I can't get the back plate off.
How do I do it?

IBNobody said:
I'm on my 3rd Epic, and this one is going back, too.
Before I send it back, I'd like to disassemble it. I think that the current problem (speakerphone returns static to whoever I talk to) is a soldering issue and may be easily debugged and fixed if I could open up the phone.
Opening up this guy is not easy.
I can remove the visible screws.
I can remove the two screws hidden under the serial number sticker / battery mat.
Even after removing these screws, I can't get the back plate off.
How do I do it?
Click to expand...
Click to collapse
Opening it voids your warranty and you will be unable to return it if your repair fails.

scriz said:
Opening it voids your warranty and you will be unable to return it if your repair fails.
Click to expand...
Click to collapse
It only voids your warranty if they can tell you opened it. I haven't run into any tamper-proof stickers.
So do you know how to get into it farther, or were you just poopoo'ing my attempt?

IBNobody said:
It only voids your warranty if they can tell you opened it. I haven't run into any tamper-proof stickers.
So do you know how to get into it farther, or were you just poopoo'ing my attempt?
Click to expand...
Click to collapse
lmao @ ====> or were you just poopoo'ing my attempt?[/QUOTE]
hilarious!

http://www.chipworks.com/samsung-epic-4g.aspx Shows some pics of it disassembled. Maybe it will provide some insight as to how to open it, and maybe not. Better than nothing. Try searching Samsung Epic teardown and digging a little deeper than the first page.

los1223 said:
http://www.chipworks.com/samsung-epic-4g.aspx Shows some pics of it disassembled. Maybe it will provide some insight as to how to open it, and maybe not. Better than nothing. Try searching Samsung Epic teardown and digging a little deeper than the first page.
Click to expand...
Click to collapse
Searched disassembly, not teardown. Thanks.
The link actually helped.
The Epic has 2 microphones?

start up at the top by the power button and use something plastic to wedge between the pieces. DONT user metal, it will scratch or break something.

Kcarpenter said:
start up at the top by the power button and use something plastic to wedge between the pieces. DONT user metal, it will scratch or break something.
Click to expand...
Click to collapse
I've found a teardown picture that illustrates the difficulty...
https://fjallfoss.fcc.gov/eas/GetApplicationAttachment.html?id=1311529
The problem was the two tabs. I didn't realize how long they were.

There are clips where the back casing sticks to the silver band around the phone. You have to use a thin flat head to separate it. Be careful since the silver band is made of plastic and will crack if bent.
I had to take apart 2 Epics and swap out a faulty keyboard with another one before returning it.

arashed31 said:
There are clips where the back casing sticks to the silver band around the phone. You have to use a thin flat head to separate it. Be careful since the silver band is made of plastic and will crack if bent.
I had to take apart 2 Epics and swap out a faulty keyboard with another one before returning it.
Click to expand...
Click to collapse
Once I saw how the back cover was snapped on (wide indents that snap to the silver), I was able to remove it. I used a credit card, sliding it down from the volume button, parallel to the phone. Every so often, I'd use the card as a wedge to pry the top off. Eventually, it snapped open.
Unfortunately, I am unable to find a problem. The main microphone works. It just doesn't work in speakerphone mode.
Oh well... I'm on my 4th Epic. I'm holding off on returning them to Amazon. I'll have 3 of 'em sitting around in case I need to make a FrankenEpic.

Do you see any way to tighten the screen slider?
Sent from my SPH-D700 using XDA App

Hey, if/while you're still in there... do you see a MLF-type chip (these are the ones that look like a plastic box with no visible pins because the metal pads are entirely on the underside) that's approximately 3mm x 4mm that has something like "FSA 9480" (or just "9480", or even "Fairchild") written on it? Probably near the USB port? I've read about its existence inside the Epic (and all Galaxy S models), and it seems to be getting enumerated by the kernel during bootup, but I didn't see any actual chip bearing the name in any teardown pics I've looked at. I'm starting to suspect that the "9480" *might* just be IP that Samsung licensed from Fairchild and incorporated into one of their own ASICs (with "9480" being the "IP name" of the chip Fairchild sells as the 9280), but it's really hard to tell.
For anyone who didn't see my other post, or the thread in the I9000 board, the FSA9480 is a USB switch that enables the USB port's two data pins to be repurposed for a) serial UART Txd and Rxd, b) Stereo audio left and right out, c) mono headset with audio out and mic in, and d) JTAG via a special interface called "JIG" that's kind of like Atmel's Debugwire and serializes the various pins of a JTAG interface. It's not actually using USB... it electronically disconnects the two pins from the USB interface, and connects them to the audio/uart/JIG pins elsewhere inside the phone.
Also, if you can see anything that resembles a manufacturer or part number for the USB port, that would be awesome. I know that someone, somewhere HAS to make them, but trying to find nonstandard, offbeat connectors in the millions of items sold by companies like Digikey, Arrow, Avnet, Mouser, etc. is like looking for a needle in a haystack unless you already know the exact part number you're looking for.

didnt really llook too hard, but i didnt see any

How difficult is it to replace the entire screen/lcd? Is it possible to easily remove the entire top off the slider and replace it?

Yes its rather easy you take off the back cover use something like a guitar pick to pop the back snaps apart then from there undo the connections to the main board remove it a few more screws under the sticker and one under the main board i think there is a ribbon cable you have to be genital with they rip really easy also make sure its put back the way it needs to be.. when replacing the screen there are tear down guides all over the new that show it in detail...
Edit: Found a Video for you... http://satmedia.co.uk/sprint-samsung-epic-4g-galaxy-s-sph-d700-take-apart-tear-down-video-mpg/
Chabsin said:
How difficult is it to replace the entire screen/lcd? Is it possible to easily remove the entire top off the slider and replace it?
Click to expand...
Click to collapse

Pry bar and hammer should do it!
Sent from my '' Bag Phone ''

[Q] Digitizer replacing

Today I aquired a HTC Trophy with a cracked screen.
It was not cost effective to have it replaced by the workshop, so I'm attempting to replace it myself.
Following the MicroSD replacement guide by DominikZ, it's been a fairly simple and straight forward process, but I have now come to a point which I'm not sure how to proceed.
I've gotten to the point where I have the two ribbon cables disconnected, and have now separated the systemboard from the front. The front frame now contains the LCD, digitizer and speaker.
Does anyone have some tips on how to proceed from here?

What about the other 3 (black) screws? Torx 6?

nlamer said:
Today I aquired a HTC Trophy with a cracked screen.
It was not cost effective to have it replaced by the workshop, so I'm attempting to replace it myself.
Following the MicroSD replacement guide by DominikZ, it's been a fairly simple and straight forward process, but I have now come to a point which I'm not sure how to proceed.
I've gotten to the point where I have the two ribbon cables disconnected, and have now separated the systemboard from the front. The front frame now contains the LCD, digitizer and speaker.
Does anyone have some tips on how to proceed from here?
Click to expand...
Click to collapse
hey man, i hope that the following site can help you abit.
i was mugging around at the "xda cn" just a minute ago,
and i saw some one had a post tutorial about how to rip out the HTC 7 Trophy safely.
(the site is below my comment), well it is all in chinese, i guess you properly won't be able to read it but the good news for you is....all these stuff is always with photos...and not just one and two...is alot...alot of photos
the photos are very details, i guess it should be able to help you out with something even a little.
Good luck with that, and once you jump in to the site...once you finish looking at the first pic, click the page 2 it will brings you to the second page, and keep looking, u should be fine with that even you don't understand the chinese..
The site:
.............
damn i'm not able to post link as im a new user in this forum
let see if you can read the link below(replace the lttp to http,xxx to www)
lttp://xxx.xda.cn/newshow.php?snid=1017&page=&pages=1
Kind Regards
Lance

Thanks for the tip Lance The pictures were easy to understand, especially when I don't read chinese.
However they did not cover removing the LCD and digitizer.
matthijs81 said:
What about the other 3 (black) screws? Torx 6?
Click to expand...
Click to collapse
The three screws on the back of the lcd casing is not screws. Those are threaded cylinders, for attaching the front with the back.

Hey there
how far have you got with repairing the screen as I also acquired a HTC Trophy with a cracked screen. The phone still works so there is no rush but I need to know what I need to repair this unit?

Hey.
No progress so far. I'm not sure how the glass is attached to the front housing, but I have an idea that it might be glued on from the front.
You may be able to extract the glass from the front by using a hairdryer and something thin, like a razorblade. However I have not tried this yet, so I can't say for sure.
Good luck ;-)

There are digitizer replace videos for the htc desire:
youtube.com/watch?v=sXZqIjtFoAU
If the Trophy is build in a similar way you can see how you to remove the glass at 4:00
You can use a hair dryer instead of an oven.

Hi folks, been a long time lurker, came here after looking for a solution to this very problem, so, nlamer here's how to do it, be warned though it's not an easy repair.
(och, I cant post image links until I have made 8 posts :-S )
see attached photos, i'll prob need to do a few replies to post them all.
1:- Strip your phone down and remove the logic board from the chassis, carefully remove the lock tabs to release the ribbon for the LCD & digitizer
2:- Use a heavy duty knife ( I used a stanley blade ) to slice the adhesive holding the LCD to the digitizer, it's only held round the edges so you dont need to go too far in
3:- Peel back the cracked digi and just slice the ribbon, it's attached to the back of the LCD and your not going to be using it again anyway
4:- The LCD is held in place with the light grey adhesive strips, use a spudger to remove it, just be careful not to put too much pressure on it or you will damage the LCD, in my experience it's always better to have a replacement on standby just incase

5:- A quick check to make sure the LCD is still ok, you never know!!!
6:- On the old digi you will need to remove the three clear plastic tabs at the bottom and transfer them to the new one, these feed the LED's to the capacitive button's on the bottom, they are held in place with some adhesive & are not difficult to remove
7:- Remove all the old adhesive and apply some knew strips, I used 3M stuff here and trimmed it to fit but I dare say there are adhesive kits available on eBay
8:- Do the same to the LCD

9:- Line up the LCD with the marks on the digitizer and press it into place, the digitizer ribbon has a small piece of adhesive to attach it to the back of the LCD
10:- Place the display into the chassis, make sure the ribbons go through the gaps in the chassis and everything lines up before committing to pressing down
11:- If all goes well after re-assembly it should be looking sweet again.
Hope that helps yourself & other's out ;-)
Regards

Thanks for the instructions irepairtechstuff. It is greatly appreciated. I almost have my device wrapped up, and ready to go, but I'm having some trouble with the digitzer.
It seems behave as it pleases, and does not register pushes and swipes as it should be. Any tips on this?

Nevermind the last post.
I cleaned the connector with some alcohol, and now it works perfectly

I just got a trophy, I don't understand the adhesive verry well. I though you had to put adhesive on the underside of the touchscreen digitizer (along the edges of the screen) and on the metal frame, under the lcd or the underside of the LCD, but in this turtorial you see adhesive along the edges of the upside of the LCD?????

HELP!
Is there nobody who can help me?

Try private messaging the users who manged to get this to work. They should receive and email and might be able to come back and look at this thread.