Hi,
I've replaced the buttonbar of the HD2, however during assembly the mainboard connector was damaged and can't be closed anymore.
See the picture for the connector (next to the mylar). Can someone replace this connector or repair and assembly it again? Offcourse I will pay for the repair and postage!
http://db.tt/s1eOo86r Photo here...
Thanks!
That is not repairable you will need a new board or you can try to apply adhesive tape to it
Related
Hi
I need to repair my qtek 2020i. The connector for the charger is "broken" as the metallic cover that fix it to the mainboard (now the connector is completely detached). I have disassembled it following the guide, but the metallic cover is to ruined cause of mine trying to repair it.
Someone knows if is possible to order only those parts.
I will attach some photo so you can understand my bad explanation (I need the parts in the red circle- the first two photos)
qtek photos
this part needs a special soldering iron.not easy to do..id buy a replacement board of ebay
Images was too blur to see but I also do think ebay is the best place to find it...
In the middle of disassembling my Legend to replace a bad digitizer, I broke the ribbon cable connecting the power button to the PCB. I haven't reassembled it yet, but I can't see how it's going to work.
img710.imageshack.us/img710/6929/brokenn.jpg
img137.imageshack.us/img137/1346/powerkz.jpg
(Sorry I can't post links because of post count.)
If anyone knows what the best way to repair this would be, I would be most appreciative. Thank you.
EDIT:
It seems this is the piece I need to replace.
tinyurl.com/28a7t9u
tinyurl.com/36yj5tw
Anyone know where I could go about finding one of these? The part number turns up nothing on Google.
I would find a service center and ask there, or I would solder it , it's just two wires....
But be sure you purchase a part with the ribbon cable on it, what I've seen it didn't look like it was there...
Good luck...
Called HTC service center. Unfortunately they don't sell parts direct.
I thought about soldering it, however the ribbon broke so close to the base that I am not sure I would be able to get access to the conductor.
Anyone have a trashed Legend that I could buy for parts?
I need help with broken lcd flex cable connector on motherboard!
I want to now is another connector fits for Trophy
Nothing?
Nobody knows any solution?
I had this happen on my Touch Pro2, but the cable still worked fine after inserting it. Maybe try a bit of electrical tape on top? I don't know if the facing side on the Trophy connector (the side that is broken has any data carry over or not?)
It's some pretty high level damage to do either way.
I try, but not work.
I hate to say it, your out of luck. :/ Unless you can find someone that can do awesome high level soldering and has access to the parts to replace it... that's it. HTC might repair it at a cost, since the phone isn't under warranty anymore, but you'd have to contact them and ask them if they would and what the price would be.
I buy one with broken LCD and Touchscreen and now I have a working Trophy.
Only thing is to change stock ROM with custom ROM.
Hey, I finally just finished replacing the broken digitizer on my T-Mobile HD2 with a new one I bought online. I turned it on after reassembling and it booted up like normal, but now there's no touch
Is there anything I can try to resolve this? Or is my phone officially dead?
Hard to give an easy answer on this.
Could be a bad digitizer or could be issue in the fitting.
You need check the connections & this should of all been done prior to building it back up.
You will have to pop the chassis out & need check mainboard to LCD ribbon first off & try reseating it to see if digi function can be regained.
Always best to to test new Digi prior to build up as a PITA if don't due to bonding it all together.
I test mine with just mainboard with a spare button board connected & lcd/digi stuck in the ribbon port all laid out flat on a desk (main ribbon not needed) & attach a battery by hand & press the end key button & hope it boots & then lcd/digi can be reviewed prior to final build up.
Favourite cause of no digi is damage to the mainboard LCD connector due to bad handling.
The digi connector to lcd also needs to be checked if no other faults or reseating of lcd/mainboard flex helps :-S
May need get another digi prior to writing other things off as some of these cheap digi units are bad due to dirt cheap manufacture & no QC plus anyone stating tested prior to shipping is talking bull so don't rule out you got a dud digi ...
Mister B said:
Hard to give an easy answer on this.
Could be a bad digitizer or could be issue in the fitting.
You need check the connections & this should of all been done prior to building it back up.
You will have to pop the chassis out & need check mainboard to LCD ribbon first off & try reseating it to see if digi function can be regained.
Always best to to test new Digi prior to build up as a PITA if don't due to bonding it all together.
I test mine with just mainboard with a spare button board connected & lcd/digi stuck in the ribbon port all laid out flat on a desk (main ribbon not needed) & attach a battery by hand & press the end key button & hope it boots & then lcd/digi can be reviewed prior to final build up.
Favourite cause of no digi is damage to the mainboard LCD connector due to bad handling.
The digi connector to lcd also needs to be checked if no other faults or reseating of lcd/mainboard flex helps :-S
May need get another digi prior to writing other things off as some of these cheap digi units are bad due to dirt cheap manufacture & no QC plus anyone stating tested prior to shipping is talking bull so don't rule out you got a dud digi ...
Click to expand...
Click to collapse
Thanks for the tips. I opened up the phone again and went through all of the connections. Everything looks fine to me, no cracks in the tapes or anything as far as I can tell. It's probably the digitizer that was sent but I'm not willing to sink another $15 on it to find out
bit of a shame ...
If you decide to break it for parts & it the TMOUS version I could be interested in the mainboard ...
I have HD2 , it was used from another person and this person told me that he is experiencing non responsive digitizer from time to time . I was thinking that with digitizer change everything will be OK , yes but NO . No i have changed this phone digitizer and it is not working again
My question is : Is there a way to check this new digitizer ? A lot of people said that it was related to the power button , but i doubt that , maybe is loose connection somewhere or re flow must be done on the screen connector on board ?
Need more info really, is it socket or solder ? did you have any improvement with new digitizer for a while or is it exactly the same symptoms as old one ?
Some of the cheap digitizers are rubbish in terms of QC so plenty of bad ones get sent out.
Bad connection of socket or solder to LCD can cause issues & so can bad fitting of lcd ribbon to mainboard, have seen a few which needed tweaking to get lcd to mainboard connection good so digi worked. Check mainboard connector carefully as if clamp bar broken or plastic cracked on top of connector as they break very easy in the wrong hands.
Worth checking button board too as have had one HD2 that would have digi issues & faulty button board was causing it .
how much cost digitizer?
epidemija said:
how much cost digitizer?
Click to expand...
Click to collapse
About 16USD if you hunt on eBay a bit.