Hello Android master's
I got USB problem
I want to instal 2.3.2 rom
Right now I'm useing 2.3.7
When I plugged USB to the computer as mass storage divce
The recognized the computer
When I enter the bootloader the three color screen
It changed from serial to USB
But when I enter to magdlr mode and choose the
USB flash it said USB mode ... and nothing
Does someone has solution for me???
Thanks very much
My guess is that you are trying to flash CWM-recovery.?
If you do, dont connect phone until DAF asks you to and it says
-waiting for usb connection
If i connect it earlier, setup fails atleast for me.
Worth a try, good luck
Related
I'm trying to connect my phone to my PC but I also get this USB Debugging Connected, I mount it but as i go to my computer nothing don't show up so I can continue the next step to get froyo 2.2 some one help me what should I do?
What worked for me (others report different) was to first connect to the PC with USB Debugging ON. The PC installed some device drivers. Unplug and turn USB debugging OFF, Ask on Connection ON, then reconnect. Then the three options, Kies, .... showed up and worked.
Hope that helped.
I'm gonna try
It's not installing nothing
Dude ****ing thank you man you are the best I am gonna remember this for now on incase thank you
Hi there guys , Im currently in a bit of a predicament. I installed XboxMods 1.04 And have been using it for a few months now. Now ive noticed NoDo is the latest ROM available. And want to get the ball rolling and get it flashed. Theres a few problems
1. When i connect my Phone to my PC , I get no 'Installing Device Driver' on my Win7 PC , I used to be connected via Zune , But i did a hard reset and havent checked since then :S
2. When i try to 'flash' i get no USB device detected etc.
3. In the HSPL screen there is no USB either its either SERIAL or Blank.
The basis is , I cant flash / use zune or anything atm.
I HAVE tried numerous USB Cables , all to no avail , Ive done 2 more Hard resets. And atm im a bit stumped on what the hell i can do.
*** EDIT*** Clean Install of Windows 7 X64 Ultimate , Hard Reset Number 6. Still nothing. I have ONLY Been using MAGLDR to flash with via USB Flash mode. HSPL / Zune / MAGLDR Do not recognise that a USB Cable has been put in. The only thing that happens is the 'charging' portion. Could this be the data side of the port being damaged?
You wouldnt flash it through the HSPL anyway if you already have an older build of wp7. You would flash it through MGLDR.
Turn phone off. Turn it back on but hold the power button until mgldr loads it menu where you can choose usb flasher. Run that plug in via usb and run dwi.exe.
reeg420 said:
You wouldnt flash it through the HSPL anyway if you already have an older build of wp7. You would flash it through MGLDR.
Turn phone off. Turn it back on but hold the power button until mgldr loads it menu where you can choose usb flasher. Run that plug in via usb and run dwi.exe.
Click to expand...
Click to collapse
Im doing that , And it doesnt notice im plugged in via USB
Check the drivers in device manager. Forgot what the name is but I had this problem also once. I uninstalled the driver then when I plugged the phone in again in reinstalled the driver and all worked fine after that.
Edit: daf.exe installs drier
reeg420 said:
Check the drivers in device manager. Forgot what the name is but I had this problem also once. I uninstalled the driver then when I plugged the phone in again in reinstalled the driver and all worked fine after that.
Edit: daf.exe installs drier
Click to expand...
Click to collapse
There is nothing in device manager to uninstall , ive done a clean install of Windows 7 X64 to see if that was the problem. And no it still doesnt show up.
Im seriously doubting 2 cables can be dead. Ones pretty much brand new.
Plug phone in while in USB flasher and run daf.exe from the original magldr download. Should pick up and install drivers from there. Or check out the band Android section for more specifics on magldr that's where alot of results came from when I googled daf.exe
Sent from my hd2 using XDA Windows Phone 7 App
Im sure your not listening to what i say.
USB Flasher Mode and ALL USB Modes dont work.
USB Flasher mode
Wait USB....
**Plugs in USB** Nothing happens. It just stays on Wait USB and has done the whole time.
And again , i have NOT been trying to flash via HSPL i never said i had at all. I used HSPL to check to see if it noticed USB connection. As when your in HSPL and plug it into USB itll say USB... Not be Blamk or say Serial.
My feeling is that the Data Parts of the USB are dead, It still charges fine , just doesnt let any data through
As the title says, my phone wont recognize when I plug in the USB on to flash the DAF. I have done it several times before but now it doesn't work for some reason? So to clarify it's stuck on "wait USB..." and won't get to the point where it says "wait USB... USB".
Using MAGLDR v1.13
Does anyone have any ideas?
Restart your PC should solve your issue....at least it does several times for me.
icke said:
Restart your PC should solve your issue....at least it does several times for me.
Click to expand...
Click to collapse
yes
If not, you would need to uninstall the drivers needed to perform the usb connection. Then connect your phone again, and it should automatically install.
Reinstall driver and try another USB port, too
I don't really depend on "wait USB ... USB" as it is not very accurate .
Sometimes, I don't see " .... USB" until I double click DWF and hit next twice.
I do get the windows sound when you connect something with usb so maybe the "wait USB isn't accurate" just wasnt sure. Will try it, thanks
my comp never "recognizes" wait usb ... usb
i just start the DAF and all goes well. go ahead and give it a go ... whats the worst that can happen? worst case the DAF wont start right? :-D
Thanks for the help guys, got it to work
What always worked for me:
Open Windows Mobile Device Center.
Turn ON USB Connections.
Connect the USB cable to the phone.
Turn OFF USB Connections.
Flash
hello
i have a problem with my g928f
my issue is that it can not be regognized by the windows
i have tried at my desktop with win 10 and at my laptop with windows 7 and at both says unknown device,
i have tried everything i know of
unistall everything from the pc regarding samsung drivers
install it again , nothing
install smart switch , nothing
install kies, nothing
run odin , not even see the phone at download mode
made factory reset from recovery , nothing
charge is working just fine both from pc and my wall charger
i tried mhl hdmi and nothing happened
tried just now otg cable with a usb drive , again nothing
just a week ago i was using it just fine with my pc
should i take it to a store to check my micro usb port??
noone??
today i replaced the screen with a new one witch had a new usb dock on it and the problem is still here
i can not connect it to any pc.
i cann't flash the stock rom because odin is not see it also
is it possible to be a rom problem????
i can't flash the stock one because of the usb issue
but i think i can download another lollipop rom to give it a try.
Have you made sure that it is set as MTP?
Setting - Storage - USB.
Check if the device gets connected in Fastboot mode. If it doesn't then it would be your USB.
sideload is not working either
usb is brand new and original.
is there a way to flash stock rom via recovery?
my nexus 6 will only charge no data transfer and pc wont recognize it. When i connect it to the pc it goes staright to charge mode and the usb trident symbol doesnt ever appear. In developer options usb configure is stuck in "charge mode" only. Ive tried different roms from pie to mm . i reinstalled bootloader and radio, tried twrp back ups and still the same. Had new charging port put in phone thinking that was the problem but didnt help. Ive searched google but couldnt find anything. Any Ideas, really appreciate it thx
When I installed stock rom which was android 7.1 it changed phone back to encrypted. Now i have to format internal drive in order to install a pie rom. Does anyone think that formatting internal drive might fix problem with not being able to do anything but charge phone from usb port, because if that doesnt fix it there would be no way for me to put any rom on my internal drive to install it.. Does anyone have any suggestions
kanpol said:
When I installed stock rom which was android 7.1 it changed phone back to encrypted. Now i have to format internal drive in order to install a pie rom. Does anyone think that formatting internal drive might fix problem with not being able to do anything but charge phone from usb port, because if that doesnt fix it there would be no way for me to put any rom on my internal drive to install it.. Does anyone have any suggestions
Click to expand...
Click to collapse
Just to double check that adb devices shows your serial #. If not, it may be a driver issue.
Computer doesn’t see it, when I enter adb devices it doesn’t show up. Nothing shows up in device manager either: Also when I enter fast boot on the phone “power lower volume button” it says “connect usb data cable” I’ve trued numerous cables that work fine on my other phone. So it’s not the cable. After I plug them into phone it still says connect usb data cable.
I also have a thumb drive with a micro usb connecter that used to work on the phone. Now the phone doesn’t see it when you plug it in to the phone. But it works on my other phone so it’s not the thumb drive
kanpol said:
I also have a thumb drive with a micro usb connecter that used to work on the phone. Now the phone doesn’t see it when you plug it in to the phone. But it works on my other phone so it’s not the thumb drive
Click to expand...
Click to collapse
It sounds like a driver problem. Is it a windows PC? Have you tried installing the Google USB driver? I've had similar issues, and reinstalling the driver(s) has worked for me.
It’s windows 10 and I reinstalled driver, other thing is in my car when I plug it in to the usb slot for android auto, it doesn’t show up in my car either and it used too.
It’s like the phone is stuck in charge only mode and I can’t get it out of that
kanpol said:
It’s like the phone is stuck in charge only mode and I can’t get it out of that
Click to expand...
Click to collapse
When you connect your other phone to your PC, does its serial # show up in adb devices? If so, I'm out of suggestions.
1 more thing.. Have you enabled USB debugging in Developer Options?
Other phones shows up and in devolpers options in “usb configuration” you can set it to mtp but when you hit enter it goes back to charge only. I was on” aiop 14.0 rom” when it happened but it was working fine on that rom , then one day android auto kept saying connect usb, so when I got home I tried to plug it into pc and nothing. So I replaced charging port thinking that was problem but it didn’t help. Flashed other roms and even went back to stock, reflashed bootloader nothing helped. I was hoping someone here had seen this before cause I googled it and nothing like this could I find
kanpol said:
Other phones shows up and in devolpers options in “usb configuration” you can set it to mtp but when you hit enter it goes back to charge only. I was on” aiop 14.0 rom” when it happened but it was working fine on that rom , then one day android auto kept saying connect usb, so when I got home I tried to plug it into pc and nothing. So I replaced charging port thinking that was problem but it didn’t help. Flashed other roms and even went back to stock, reflashed bootloader nothing helped. I was hoping someone here had seen this before cause I googled it and nothing like this could I find
Click to expand...
Click to collapse
Forget USB configuration for a minute. In developer options, under debugging, USB debugging needs to be enabled.
usb debugging is enable also. even tried turning it off and back on again, didnt help.
you know when you connect phone to pc and you normally see the usb trident symbol on your phone, well when i connect it to the pc i dont see that symbol it just goes straight to charging but even charging i should still see the usb symbol and i dont,