Related
Hi, this is a funny situation I'm in because 99% of the time I find solutions to my own problems searching this thread but I'm in a unusual situation and I'm looking for suggestions.
I was running MDJ cynogenmod 7 v.2.2 under CWM and MAGDLR 1.11 with no problem, however because some apps did not work in gingerbread I decided to go back to froyo, which I tried MDJ revolution also on MAGDLR under CWM, and got stuck on a bootloop. I blamed my partitioned (Fat/EXT4) SD card and formatted it (FAT)only and re-flashed REVOLUTION via CWM, still got bootloop so i went over CWM, and flashed it via USB Flasher to be stuck in bootloop again, just before i started crying about my dead HD2 I figured to flash windows 6.5 again and thankfully it worked. But after 5 minutes of using windows I needed android so I downloaded a SD version and tried to run it via Heret, and this is where the situation comes because I already tried many versions of android SD and none bootup. Yea it sounds like my SD but I have already formatted, any suggestions would be appreciated.
ralphsancho said:
Hi, this is a funny situation I'm in because 99% of the time I find solutions to my own problems searching this thread but I'm in a unusual situation and I'm looking for suggestions.
I was running MDJ cynogenmod 7 v.2.2 under CWM and MAGDLR 1.11 with no problem, however because some apps did not work in gingerbread I decided to go back to froyo, which I tried MDJ revolution also on MAGDLR under CWM, and got stuck on a bootloop. I blamed my partitioned (Fat/EXT4) SD card and formatted it (FAT)only and re-flashed REVOLUTION via CWM, still got bootloop so i went over CWM, and flashed it via USB Flasher to be stuck in bootloop again, just before i started crying about my dead HD2 I figured to flash windows 6.5 again and thankfully it worked. But after 5 minutes of using windows I needed android so I downloaded a SD version and tried to run it via Heret, and this is where the situation comes because I already tried many versions of android SD and none bootup. Yea it sounds like my SD but I have already formatted, any suggestions would be appreciated.
Click to expand...
Click to collapse
this might sound a bit daft but have you checked the radio version after flashing the winmo rom?
despy1989 said:
this might sound a bit daft but have you checked the radio version after flashing the winmo rom?
Click to expand...
Click to collapse
yes i have the same radio i always had 2.10.50.26
Just wondering, did you have the correct partition size for system?
Use "SD Card Formatter" and set it to FULL and ERASE ON.
thank you!
thanks for your quick help
after running windows for one day I decided to give MAGDLR another try and just like that it worked perfectly and flashed a very old MDJ Revolution build. it seems that after I formatted SD to FAT only I stupidly tried to flash a APP2SD nand build, which [i think] caused the problem [idk if this was it but my guess is that ap2sd builds only work if you have a [FAT]/[EXT] formatted SD Card (i thought it was kind of optional)]
as for running android via SD, no luck via windows, no luck via MAGDLR, but I have it via nand so I am very very happy
Thread closed
I was using Android on the phone and I decided to upgrade Android to a better version of Android lol. My android is gone and I am stuck in MAGLDR..I tried to copy android and CWR to sd card and boot it in MAGLDR but nothing happens.
Is my phone forever like this now? or is there a way?
Appreciate your help! thanks
dicksonjoe said:
I was using Android on the phone and I decided to upgrade Android to a better version of Android lol. My android is gone and I am stuck in MAGLDR..I tried to copy android and CWR to sd card and boot it in MAGLDR but nothing happens.
Is my phone forever like this now? or is there a way?
Appreciate your help! thanks
Click to expand...
Click to collapse
can u xplain more about ur issue
Sent from my HTC HD 2 powered by HYPERDROID
I'v got exactly the same problem.
After deleting the ''old'' android and updating MAGLDR from 1.11 to 1.13 it just wont run CWM...
So i'm running stock ROM right now, Sucks!
did you install the new CWM?
Yes i did !
because magldr 1.13 and the latest cwm now work differently.
old way - cwm on sd card - magldr option 2 'boot ad sd' started cwm.
new way -
flash magldr 1.13
get new cwm, and flash it, , it now flashes to the nand, and doesnt require anything on sd to run, just the new partition layout.
Then, magldr - option 8 AD recovery starts cwm.
1. Reflash Radio .. I recommend the 2.15.50.14 Radio If you have a T-Mobile 1024
2. TASK29 Phone .. this will Clear / Erase The Rom
3. Reflash MAGLDR And ClockworkMod Recovery in that order! ( Get Files From Link! )
4. FORMAT SD CARD! FULL WIPE and FORMAT .. I use Panasonic SD Formatter
5. COPY Android Rom ZIP USING SD CARD READER! .. If you dont have one BUY One!
Do Not Use MAGLDR And ClockworkMod Recovery to Copy Rom Zip To SD CARD!
IF AFTER YOU HAVE DONE ALL OF THIS AND IT STILL FAILS .. TRY A NEW SD CARD!
I Have Seen Many Times Its a Bad SD Card!
All Programs & Everything you need is in this thread!
click> http://forum.xda-developers.com/showthread.php?t=981811
Thanks man, You knew exactly what was wrong. I had to install hspl from bootloader and then radio. From there, I got MAGDLR 1.13, usb storage mass, copied CWR and Nand. Thanks so much!
replacing sd card worked for me
I was going though the steps to set up dual boot for android and wm 6.5. I haven't put an android version on it yet, but I can't get it to go into wm 6.5 to do it later. Please help to get to wm 6.5 Please can't use phone.
Oops, ignore this post.
I was able to successfully install CWM on one HD2 and is now running Android on it.
Well that HD2 the touch screen no longer work. So i purchase another HD2 and attempt to do the same, but once I install Recovery 150, I go to AD Recovery and I get stuck on "GO GO GO!" CWM won't load. Can anyone give me suggestion to what might be the problem.
What I have tried so far.
1. I reload HSPL3 to 2.08.HSPL
2. Flash Task29
3. Flash Radio 2.25.50.14
4. Flash MAGLDR 1.13
5. Flash Recovery 150MB
then when I boot in to AD Recovery I get stuck on GO GO GO!.
When I Flash 250 or 400 I get FATAL in red.
SO i attempt to flash the OEM T-MO rom it hang at 8% and crash. Don't know what I'm doing wrong. I can get into the bootloader fine.
itzstevo said:
I was able to successfully install CWM on one HD2 and is now running Android on it.
Well that HD2 the touch screen no longer work. So i purchase another HD2 and attempt to do the same, but once I install Recovery 150, I go to AD Recovery and I get stuck on "GO GO GO!" CWM won't load. Can anyone give me suggestion to what might be the problem.
What I have tried so far.
1. I reload HSPL3 to 2.08.HSPL
2. Flash Task29
3. Flash Radio 2.25.50.14
4. Flash MAGLDR 1.13
5. Flash Recovery 150MB
then when I boot in to AD Recovery I get stuck on GO GO GO!.
When I Flash 250 or 400 I get FATAL in red.
SO i attempt to flash the OEM T-MO rom it hang at 8% and crash. Don't know what I'm doing wrong. I can get into the bootloader fine.
Click to expand...
Click to collapse
first off once you do HSPL you don't ever need to do it again, and the radio you flashed was 2.15.50.14? once you flash the radio you don't need to reflash it again, unless changing to a different one.
Now I would suggest to start back at task29,
then MGLDR 1.13,
redownload the partition in case of any corruption,
are you using win xp or 7?
if on win 7 right click on the daf and run as admin.
I know there's not much difference from what you said but maybe you have a corrupted download and it's messing things up.
Try using the toolkit, it does a really good job:
[2 Jun 11][v3.9] HD2 NAND Toolkit - All in one Toolkit for HD2 NAND Users
I'm using windows vista & i tried the HD2 NAND toolkit still the same result. :/
so i gave the freezer cooling theory a try and it works. Now I got another problem on hand i can only use the phone no more than 20-30 min at a time before it locks up.
itzstevo said:
so i gave the freezer cooling theory a try and it works. Now I got another problem on hand i can only use the phone no more than 20-30 min at a time before it locks up.
Click to expand...
Click to collapse
Then you have a hardware issue with the phone itself!
Sent from my HyperDroidCM7 HD2
sebasmiles said:
Try using the toolkit, it does a really good job:
[2 Jun 11][v3.9] HD2 NAND Toolkit - All in one Toolkit for HD2 NAND Users
Click to expand...
Click to collapse
Thanx a lot, I solved problem "stuck on GO GO GO!" with HD2 NAND Toolkit!
I often encounter this problem,too
I really dont know sorry for u
hi there guys i need help i have TyphooN CyanogenMod 7.2 RC3 v3.8.5[2.3.7][A2SD+][tytung r1 nand rom installed,on htc hd2 working perfect but recently i wanted to access ad recovery in magldr it loads 123456 go go go,and then freezes ,i can not get in to clockwork recovery but i did not have that problem before can some one help please,thanks and i do not want to loose the nand rom ,im a newbiee
itzstevo said:
so i gave the freezer cooling theory a try and it works. Now I got another problem on hand i can only use the phone no more than 20-30 min at a time before it locks up.
Click to expand...
Click to collapse
i'm having exactly the same problem, i'm trying to install android because if i install the stock rom it stucks at the htc logo an when i install android it works for a few minutes but then it freezes
i've searched on google for it and they say that it can be a overheating problem
It was a touchscreen issue when i had this error. I had replaced the digitizer but the ribbon came loose during repair. If, when you boot to the tricolor screen (hold volume down + power), you dont see cotulla hspl 0x40 or 0x50 you have a touch screen problem.
Sent from my GT-N8013 using Tapatalk 2
stuck on go go go!
tanny1 said:
hi there guys i need help i have TyphooN CyanogenMod 7.2 RC3 v3.8.5[2.3.7][A2SD+][tytung r1 nand rom installed,on htc hd2 working perfect but recently i wanted to access ad recovery in magldr it loads 123456 go go go,and then freezes ,i can not get in to clockwork recovery but i did not have that problem before can some one help please,thanks and i do not want to loose the nand rom ,im a newbiee
Click to expand...
Click to collapse
seems like no body found a good way to resolve this issue. because I'm still struggling with it.
Please help.
jimani said:
seems like no body found a good way to resolve this issue. because I'm still struggling with it.
Please help.
Click to expand...
Click to collapse
Hi jimani, welcome to the forum. Please provide more information about your problem, which recovery? what size recovery partition? What have you tried? Hspl?
The more information you can give, the more likely someone will know what your problem is.
Robbie P said:
Hi jimani, welcome to the forum. Please provide more information about your problem, which recovery? what size recovery partition? What have you tried? Hspl?
The more information you can give, the more likely someone will know what your problem is.
Click to expand...
Click to collapse
Hi Robbie,
Actually I tried every thing:
At the first time it was a touchscreen issue, I replaced it and try to reinstall the android rom; i used the toolkit 4.3 to flash.
1.HSPL3
2.WIPE(Task 29)
3.Radio-Leo-2.15.50.14
3.MAGLDR 1.13
4.Repartition 280MB for system, 5 for cash.
But when I tried to go in AD RECOVEY, my phone stuck 1234 GO,GO,GO.
I perform this steps on two htc hd2( one is T-Mobile) but no success.
Please help.
Justin.
did you install hspl 2.08 using hspl3?
Which recovery have you installed and how did you install it?
Have you tried an sd recovery, booted from ad sd dir?
Robbie P said:
did you install hspl 2.08 using hspl3?
Which recovery have you installed and how did you install it?
Have you tried an sd recovery, booted from ad sd dir?
Click to expand...
Click to collapse
Hi Robbie,
Yes I installed hspl 2.08 using hspl3.
After DFT MAGLDR Boot loader is loaded I install the partition after that I go in ad recovery to load the Clockwork Mod Recovery then... stuck!
When I tried to boot from the sd card it's say : SD open kernel failed .
I don't know may be I'm mixing things. can you provide me a clear step by step doc?
Thanks in advance.
Justin.
Am at work now, have you tried using hd2 toolkit to install your nand recovery?
Else to use an SD recovery, you have to specify the folder that the zImage and initrd.gz files are in, using magldr ad SD dir, then boot from ad SD.
Robbie P said:
Am at work now, have you tried using hd2 toolkit to install your nand recovery?
Else to use an SD recovery, you have to specify the folder that the zImage and initrd.gz files are in, using magldr ad SD dir, then boot from ad SD.
Click to expand...
Click to collapse
Yes I tried many ways: hd toolkit, tools separately,...
also I tried to specify the folder that the zImage and initrd.gz files are in,but still giving that horrible message:SD open kernel failed
Someone please help me!! Before all i problems my phone kept freezing in boot and i tried everything by cleaning my sd, ad hard reset and changing builds and the same boot freeze kept happening. So after getting tired of that and having to hard reset everyday i eventually flashed TMOUS stock rom then after tried to do the magldr 113 isntall. I got magldr installed on my phone and then i choose the ad recovery. When i do i get this message "no boot source". I tried looking up on these forums and can't find anything to fix my problems. Someone please help me with a step-by-step guide. I don't want to own an hd2 running the crummy wm6.5 :/ I NEED ANDROID
download hd2 toolkit. afterward install magldr update recovery, follow the prompts to install and your done. in a nutshell...you were missing clockwork recovery. let me know if this helps
danielfc741 said:
Someone please help me!! Before all i problems my phone kept freezing in boot and i tried everything by cleaning my sd, ad hard reset and changing builds and the same boot freeze kept happening. So after getting tired of that and having to hard reset everyday i eventually flashed TMOUS stock rom then after tried to do the magldr 113 isntall. I got magldr installed on my phone and then i choose the ad recovery. When i do i get this message "no boot source". I tried looking up on these forums and can't find anything to fix my problems. Someone please help me with a step-by-step guide. I don't want to own an hd2 running the crummy wm6.5 :/ I NEED ANDROID
Click to expand...
Click to collapse
do this...depending on the recommended recovery size (typically 5-150-5 for non sense versions) download a recovery from here ..then restart you phone...go into magldr...go to flasher...once the usb is linked to pc run daf.exe from the recovery (extracted folder)...u will then have recovery installed
gdsbalaji said:
do this...depending on the recommended recovery size (typically 5-150-5 for non sense versions) download a recovery from here ..then restart you phone...go into magldr...go to flasher...once the usb is linked to pc run daf.exe from the recovery (extracted folder)...u will then have recovery installed
Click to expand...
Click to collapse
YOU SIR ARE GREAT!!! thanks so much!!!!! i can now use android! im glad it works.
Welcome...glad it worked
Sent from my HTC HD2 using XDA App
gdsbalaji said:
do this...depending on the recommended recovery size (typically 5-150-5 for non sense versions) download a recovery from here ..then restart you phone...go into magldr...go to flasher...once the usb is linked to pc run daf.exe from the recovery (extracted folder)...u will then have recovery installed
Click to expand...
Click to collapse
Great ! I will try it out as well. I have been getting this error for the last few times. I am not sure why this happened.
I installed a WP7 rom and then went back to android (hopeless battery drain with my SD card ... not sure if I can ever do something about that). I could not get back to AD recovery.
Thanks again !
gprash said:
Great ! I will try it out as well. I have been getting this error for the last few times. I am not sure why this happened.
I installed a WP7 rom and then went back to android (hopeless battery drain with my SD card ... not sure if I can ever do something about that). I could not get back to AD recovery.
Thanks again !
Click to expand...
Click to collapse
If you loaded WP7 it may have locked your SD Card - need to format in a Nokia phone. Or reduced the usable size to 200mb - this can be fixed with a partitioning tool from PC
when go back and forth between WP7 and Android the nand is overwritten ... thats why you loose your AD recovery.
REMEMBER - if you ever try WP7 and come back to Android dont forget youll need to task 29 (to clean out that nasty M$ dirt!), flash magLDR, flash recovery ( i usually stick with a 200 mb partition, as i usually run Hyperdroid, AND that way there are no worries about bad blocks), and then the rom.
although its not NECESSARY its recommended buuuut to avoid weird restarts, FCs, and any other random glitches that may occur down the short road ITS NECESSARY! :-D
good luck
hello everyone! I just installed android on my HTC HD2 successfully but when the phone reboot, shows me the MAGLDR says me that android booting from start and I have to setup android everytime I reboot the phone from the start. someone help me passing this step. thankyou in advance
Hello xda members i want to install an android rom on my hd2, as after i got the screen fixed it lost the rom I had installed and yhen i could not install new ones.. So followed instructions below and got stuck on the second paragraph
Connect the device to the USB port
Put the device into factory flash mode by booting it while pressing "volume down"
Install HSPL using the "Install HSPL" function inside HD2ToolKit - MAGLDR: Android / WP7 supports 2.08 ONLY!
Put the device into factory flash mode by booting it while pressing "volume down"
Do "Task29" (aka Complete Wipe) using the "Wipe (Task29)" function inside HD2ToolKit
Put the device into factory flash mode by booting it while pressing "volume down"
Install Latest Radio Firmware using the "Install Custom NBH/NB RUU" function inside HD2ToolKit - HD2 Radios
Put the device into factory flash mode by booting it while pressing "volume down"
Install Latest MAGLDR using the "Install MAGLDR" function inside HD2ToolKit
Boot into MAGLDR recovery menu by pressing the "shutdown/hangup" button while booting up
Choose "USB Flasher"
Click to expand...
Click to collapse
The above all appeared to work and go well
Flash the Latest CWR (Clockwork Recovery) with the appropriate partition sizes by using the "Repartition" button inside the HD2ToolKit: System: 200MB | Cache: 5MB
Boot into MAGLDR recovery menu by pressing the "shutdown/hangup" button while booting up
Insert MicroSD card with the ROM ZIP
Choose "AD Recovery"
Flash ROM ZIP
Reboot
Click to expand...
Click to collapse
Okay the problem is CWR (i downloaded the 150mb version as thought that will work with the rom) It will not install properly and I can not load the CWR menu up. 8. 'AD recovery' states in red "No sources".
Another error message I got is when I first start my phone I get this "Nand Kernal open failed"
Please help me I need to get this fixed as the phone is a present for someone.
Did you use the repartition option in the toolkit or you downloaded a separate package?
Use the option in the tool, and make sure you select the sizes according to the ROM you want to install.
Of course the device would say nand kernel failure, there is nothing in the device. After installing the recovery you need to flash a ROM, obviously.
Sent from my NexusHD2 using xda app-developers app
Marvlesz said:
Did you use the repartition option in the toolkit or you downloaded a separate package?
Use the option in the tool, and make sure you select the sizes according to the ROM you want to install.
Of course the device would say nand kernel failure, there is nothing in the device. After installing the recovery you need to flash a ROM, obviously.
Sent from my NexusHD2 using xda app-developers app
Click to expand...
Click to collapse
Thanks for getting back to me,
This is the rom i tried to install but any rom will be fine to be honest!
[17.DEC.2012║ROM] myMIUI 15 B5 [MAGLDR/CLK║Dorimanx║GB║myMIUI IDE©║zipA║MultiLang]
So i did a wipe 29 again, the radio is Radio-Leo-2.15.50.14 and i googled it to download,
just to make sure the repartition was done from the HD2 tool, all stages complete and repartitioned to rom specs 200mb and 5mb cache, so repartition from HD2 tool installs cwmod then?
8. AD Recovery - still stuck saying gogogo..
Which radio do you have installed?
Marvlesz said:
Which radio do you have installed?
Click to expand...
Click to collapse
Radio-Leo-2.15.50.14 I dont know if your supposed to see the radio show up on one of the screens in magldr or hspl? but i've not seen anything that shows the radio loaded other than "success" after the initial installation.
It was installed through HD2 toolkit after extracting the two files to desktop.
Also I downloaded the radio from file sharing website after I googled it as the links on xda were no longer working.
thanks,
Well, I am sorry but I am no expert in MAGLDR. All I know is that the infamous Stuck @ GOx3 had been fixed in MAGLDR v1.13.
If you already have v1.13, I am at the limit of my knowledge, sorry.
You could try to re-install though.
Marvlesz said:
Well, I am sorry but I am no expert in MAGLDR. All I know is that the infamous Stuck @ GOx3 had been fixed in MAGLDR v1.13.
If you already have v1.13, I am at the limit of my knowledge, sorry.
You could try to re-install though.
Click to expand...
Click to collapse
Okay mate thanks for your help anyway it was nice of you to take the time to try to help me .
I hope someone else on these forums will help me, I guess i can still go back to the old windows 6.5. I read someone else had similar problem and ended up going back to 6.5. It's a shame because i was giving the phone as a present and wanted it in good working order with android or at least the new windows mobile system..
Maybe the old methods of installing android on the SD card without magldr would work, I would need to find the posts with guides for that as it was such a long time ago when I went through those instructions I really cant remember.
repartition again, if it not work, try this way
gdsbalaji said:
do this...depending on the recommended recovery size (typically 5-150-5 for non sense versions) download a recovery from here ..then restart you phone...go into magldr...go to flasher...once the usb is linked to pc run daf.exe from the recovery (extracted folder)...u will then have recovery installed
Click to expand...
Click to collapse
that's all I can help
You know, you could hit the thanks button for Marvlesz
Anyway, I can't see where you're going wrong here. All your steps are (as far as I can see) perfectly fine. Just to double check, you have:
HSPL 2.08
Radio 2.15.50.14
MAGLDR 1.13
CWM (from the Toolkit)
right? If so, everything should theoretically work correctly. Try downloading an older CWM version such as the one from the guide in my sig and flashing that instead.
Thankyou tried that tin1203 and I found the 250mb and 400mb (old version) but couldn't download the 150mb version..Links dead
Still stuck on 8.AD recovery.
However instead of being stuck on gogogo, AD recovery simply stated "No Boot sources"
Anything else I can try? Or know a guide to at least get the phone back to working in some form? Cheers
Nigeldg said:
You know, you could hit the thanks button for Marvlesz
Anyway, I can't see where you're going wrong here. All your steps are (as far as I can see) perfectly fine. Just to double check, you have:
HSPL 2.08
Radio 2.15.50.14
MAGLDR 1.13
CWM (from the Toolkit)
right? If so, everything should theoretically work correctly. Try downloading an older CWM version such as the one from the guide in my sig and flashing that instead.
Click to expand...
Click to collapse
Yep HSPL 2.08 installed
Now how would i check the Radio? Install it again and receive confirmation once installed? Or is there another way to check?
MAGLDR 1.13 is installed
CWM from the toolkit will not load up - when installing it everything appears to work and install fine ( no errors etc) However 8. Ad recovery will not load up.
Anything else i can do to at least get the phone operational.
To check the radio, turn your phone off then on again. While it's booting up (on the first splashscreen) three lines of text will appear. The top one is something like R: 2.15.50.14 (or whatever radio you have, obviously) so try checking that line and making sure that it's a .50 radio. If it is, then everything worked fine when you flashed the radio. Also try the CWM version from the guide in my sig, it's supposed to be one of the most stable versions I think.
Hey i think i know what your problem is and since it's a present i hope that will work...there are two types of recoveries...the ones flashed on nand that can be booted from 8.ad recovery...and the ones flashed on the sd that can be booted from the 3rd option of mgldr..i think is called 3.ad sd..i really hope this will help!
eliaskammas said:
Hey i think i know what your problem is and since it's a present i hope that will work...there are two types of recoveries...the ones flashed on nand that can be booted from 8.ad recovery...and the ones flashed on the sd that can be booted from the 3rd option of mgldr..i think is called 3.ad sd..i really hope this will help!
Click to expand...
Click to collapse
Thanks for the help guys, after my previous post I decided to try installing windows 7 and all went well in terms of flashing the rom however although it appears to have loaded I have no touch screen, its completely not working
This could be due to windows 7 software or when it got fixed as I not used the touch screen since..
Oyeah thanks for helping, just need to get someone to fix the touch screen i guess.
It would be better for you if you install cwr from toolkit, just select the partition size(magldr repartition) for eg. 150 like you want and you'll get cwr v5.0.2.6.. Those recoveries that you're downloading from guide suck, didn't work for me too(ok, they worked but I couldn't flash anything even if I downloaded the 400 one).. Recommended.
EDIT: Sorry, haven't seen the second page of the thread where you already mentioned that cwr from toolkit won't boot.
Shaumaaa said:
It would be better for you if you install cwr from toolkit, just select the partition size(magldr repartition) for eg. 150 like you want and you'll get cwr v5.0.2.6.. Those recoveries that you're downloading from guide suck, didn't work for me too(ok, they worked but I couldn't flash anything even if I downloaded the 400 one).. Recommended.
EDIT: Sorry, haven't seen the second page of the thread where you already mentioned that cwr from toolkit won't boot.
Click to expand...
Click to collapse
Yeah thanks I really tried a lot of stuff and I know the basics been flashing since HD2 came out, I ended up flashing new windows and it actually loaded up but then guess what? The touch screen is not responding, ill be taking it back to where I got that fixed to complain.