Related
Ok, so i got fed up with my phone freezing so i thought i would get SEUS to
re install the rom, (mr1, mr2 is not available to me yet).
The indicator got to about an inch along when a message popped up saying
update failed.
Now i cannot enter bootloader to try again, the phone will not turn on, SE refuse
to help saying it is not released in the UK so i am not entitled to support.
I have not yet had a reply from where i got it from.
Is there any way to get this piece of junk going again?
Thanks.
Try to charge your battery on another phone / external charger.
I encountered a similar problem when trying to flash the X2. I received the UPDATED FAILED error, pulled out the battery, Volume Down + Power and gave it another try.
SEUS shouldn't brick your phone, maybe it's a problem with your battery.
The battery is at about 80%, i have tried it in my X1 as it is the same battery.
I tried the X1's battery in the X2 as well.
When i press the volume down and power buttons it vibrates for a fraction of a
second and then just stays on a black screen.
Let's try then a forced bootmode connection.
1. Insert the data cable into the phone without the battery plugged in.
2. Open SEUS and go to the connection screen.
3. While the software is searching for the phone, keep VOL DOWN + POWER and insert the battery.
After the phone vibrates, the software should recognize the X2.
This procedure generally applies to dead phones and sometimes works.
Post the result.
Still nothing, i kept the buttons pressed for about 30 seconds, then vista popped up a message 'usb device not recognised' the phone stayed as it did before and SEUS did nothing.
Sadly the support excuse they are using is what a lot of manufacturers do if you are in an area where they don't support it. This is the downside of buying a device on eBay etc. before it is "officially" released in your area. Contact the point of sale and hopefully they can send it in for you. You might have to pay shipping costs.
Leave your battery out and unplugged for an hour and then try again after that to revive it.
I did not even realise it had not been released in the UK, i got it from a UK website.
I am still waiting for them to get back to me, as it is Sunday they won't be getting back to me till Mon Tue i would think.
SE were fast though, less than an hour to reply, about the only credit they get though.
I have had the battery out for more than an hour a few times so that does not work.
Thanks for the suggestions though, keep em coming if there are any more.
WINE GLASS said:
Ok, so i got fed up with my phone freezing so i thought i would get SEUS to
re install the rom, (mr1, mr2 is not available to me yet).
The indicator got to about an inch along when a message popped up saying
update failed.
Now i cannot enter bootloader to try again, the phone will not turn on...
Click to expand...
Click to collapse
The exact same thing happened to me today, but I did not even get the update failed message (but I got the inch )
The phone is now bricked. No bootloader no nothing.
I guess you guys have the Singapore English versions? A lot of those retailers in the UK were getting them through Malaysia and so on. Then selling in the UK but not informing buyers that SE wont support it in the UK yet. It's really sad
It's a French X2, and I got it in France. I think I will have no issue with getting my X2 unbricked (or replaced), SE support is pretty good over here.
But if in the mean time someone has an idea or a trick on how to unbrick a X2 (other than the tips already listed in this thread), I would be happy to test it
HI!!
I have a T3238+ with a K3 Proccessor, I flash it with a wrong ROM, when I try to reflash again the K3Aid tool display the following error message : "Read FTM State Error" after i click the download mode button, Anyone can help me??? thank you!!!
-kOS- said:
HI!!
I have a T3238+ with a K3 Proccessor, I flash it with a wrong ROM, when I try to reflash again the K3Aid tool display the following error message : "Read FTM State Error" after i click the download mode button, Anyone can help me??? thank you!!!
Click to expand...
Click to collapse
Wrong phone, wrong forum, wrong idea.
-kOS- said:
HI!!
I have a T3238+ with a K3 Proccessor, I flash it with a wrong ROM, when I try to reflash again the K3Aid tool display the following error message : "Read FTM State Error" after i click the download mode button, Anyone can help me??? thank you!!!
Click to expand...
Click to collapse
Learn to "Read" and use the "Search" function newb.
Hi!
This has happened to me also. The solution was to connect the original charger (I usually charge from the USB port on my PC).
Try this:
1. Disconnect all cables from phone.
2. Remove battery.
3. Insert battery.
4. Connect original SE charger and charge for 5 minutes.
5. With the charger still connected, press volume down and then power on simultaneously - hold until SE logo appears.
If not working, repeat from step 1 several times (i tried 3 times before it finally worked).
6. Connect PC USB and run SEUS update.
Seems to me like the phone does not always charg from USB, and that when it enters the "black-screen-after-short-vibration-after-power-on"-mode it does not charge while in this mode.
Mod edit: not rom dev related, moved to general
well... when it say update fail but if save the new rom to ur phone then its fine, take the battery out and restart ur phone.. it should load the new OS.. my one says fail everytime.. so no problem for me
Hi Guys,
I got into a problem here, and I need help! I have a milestone 2 with the latest Endlees CyanogemMod, Android 2.3.7.
I was trying to follow the steps into using the internal memory as a SD card (link http://forum.xda-developers.com/showthread.php?t=948887), but I wasn't successful.
Here cames what I did:
First I tried to follow the steps:
1- create a file image in /data and a folder in /sdcard
mkdir /sdcard/storage
su
dd if=/dev/zero of=/data/storage.img bs=1024 count=5242880 (1024x1024x5 --> 5Gb)
busybox mkfs.vfat /data.storage.img
But that didn't work, the terminal emulator just said that the directory couldn't be found.
Then I downloaded Busybox from Android Market, and installed it. But when I executed the program, the installation wasn't done because it was insisting that Busybox wasn't able to access the folder, and didn't have superuser access to root. Even with the permission on Superuser OK!
So after that, I tried to reboot my milestone 2, and now it won't even get to the boot screen of android (screen with the rotating square)
I tried to use the boot recovery tool, and wipe all system data, and reboot, mas it isn't working. Something I noticed on Recovery Tool is that apear a messagem saying "E: Can't Open /cache/recovery/command" and "E: Can't Open /cache/recovery/caller.
Even the battery light won't turn on. If turn off the cell and try to recharge it, appears a image of the battery with a "?" on it... I tried to connect the cellphone to the PC with the usb cable, but it isn't recognized...
I hope someone can help me, I just can't afford to lose this phone.... Thanks
Look in this topic http://forum.xda-developers.com/showthread.php?t=1344740 it should help you solve this problem
in general: firstly you need to charge your battery in another working Milestone 2 or in some universal battery charger (because bricked Milestone 2 is not able to charge battery) and then you need to flash SBF and it should be ok
Anonymous_ said:
Look in this topic http://forum.xda-developers.com/showthread.php?t=1344740
in general: firstly you need to charge your battery in another working Milestone 2 or in some universal battery charger (because bricked Milestone 2 is not able to charge battery) and then you need to flash SBF and it should be ok
Click to expand...
Click to collapse
I read somewhere else that even if the MS 2 is bricked the battery charges. Very very slowly, but it charges.
thanks for your tip... I read the entire topic, but there is a problem. My battery must be around 30% or something, but when a connect the milestone 2 with the pc via usb cable, the lateral light won't even lit... And the pc won't even recognize it...
edit: when I connect the cellphone to the pc, the light lit for 30s more or less, the appear the Motorola logo with the rabbit on the side, but then the light turn off and I get stuck in the same situation...
carpet55 said:
I read somewhere else that even if the MS 2 is bricked the battery charges. Very very slowly, but it charges.
Click to expand...
Click to collapse
I don't know, maybe it is possible, but I as far as I know, everyone, who had bricked M2, charged the battery outside his phone...
So he can try it in the bricked phone, but he can't be 100% sure it will charge, right?
colucci.ti said:
thanks for your tip... I read the entire topic, but there is a problem. My battery must be around 30% or something, but when a connect the milestone 2 with the pc via usb cable, the lateral light won't even lit... And the pc won't even recognize it...
edit: when I connect the cellphone to the pc, the light lit for 30s more or less, the appear the Motorola logo with the rabbit on the side, but then the light turn off and I get stuck in the same situation...
Click to expand...
Click to collapse
Yes, thats why I said here and even in the topic I referred to, you have to charge battery in another non-bricked Milestone 2 or in universal battery charger. When your M2 is bricked, it wont charge any battery (or maybe it will, but very very slow according to carpet55's post ).
So now you have to get some universal charger or working M2 (or another battery).. This is your step no. 1. Then you can flash it via RSDLite by SBF file.
ok Anonymous_!
I'm going to find a way to charge the battery and do what are you saying.
But RDS Lite can flash the android even if windows it isn't recognizing the cell phone on the usb?
thanks again! I'll return with more info when I get my battery fully charged..
After you will have charged battery, you will have to boot into bootloader by holding Power+Volume Down+Camera button, then windows should recognise it (maybe you will have to install drivers too) and then you can use RSDLite (don't forget to run it with administrator rights).
Anonymous_,
final question of the day... Where do I get the SBF file?
I'm from Brazil, so should be the brazillian version of this link?
and-developers.com/sbf:milestone2
You are on the right path
Grab Brazil 2.2 version from http://and-developers.com/sbf:milestone2 and it should be ok.
I can confirm that no, the battery does not charge when bricked. I left mine going for over 24 hours and nothing -_-. So ended up using a universal ac adapter set to 5 volts and some wires directly to the + and -. This didn't work after half an hour so I upped it to 7v and about ten minutes later, all good.
During my research to find how to fix it, someone was saying the charge sequence software in in the system or boot data, and since it was all corrupt - no charge.
But you perhaps allready have enough juice in there to load up bootloader successfully, so try what anon said and hold d-pad up and power on until the screen flashes blackish grey and let go. Then it'll tell you if the battery has enough charge to flash a sbf
Sent from my A953 using xda premium
Guys,
I'm thankful to everyone who tried to help me, especially Anonymous_!
Yesterday, in the same day I bricked my phone, I flashed it even without charging to 100%... and everything has gone well, but it was a close call, because my battery had only 5% left when the milestone returned to live!
Good to hear!
Sent from my A953 using xda premium
urgent help required, please help me fast...
I just got an Xperia X10 with 2.1 android, updated with PC companion, update failed now phone is not turning on just vibrates when pressing power button but nothing on screen, also tried SE update service but nothing worked, I really need ur help guyz, please tell me what should I do now..
I have downloaded the flash tool from here
http://forum.xda-developers.com/showthread.php?t=920746
but the link of firmware is dead, pls give me a link to firmware so i can unlock it
1) fully charge
2) then use SEUS - i suspect that if SEUS won't work then flashtool wont either.
search the x10 thread for firmware thread, it is there somewhere.
good luck
how to charge it when the phone is not working ? i put in the charger, green light turn on, after 1 minute it turns off then nothing
then i am afraid i have no idea
perhaps someone else will help, good luck.
PLEAASSSEEE people help me i got this phone today and haven't used for 1 hour and now it's dead.. pls pls help me ASAP
KashishGupta said:
PLEAASSSEEE people help me i got this phone today and haven't used for 1 hour and now it's dead.. pls pls help me ASAP
Click to expand...
Click to collapse
Lol
Go in pc companion and click repair and follow the instructions
Sent from my X10S using Tapatalk
*not responsible if this screws your phone up*
Once i had a similar problem, ages ago, phone would not charge after a failed SEUS repair. I used one of the battery calibration methods to force the phone to charge, it did and i was then able to re-flash firmware.
*please try the method mentioned above FIRST - i.e try using pc companion/flashtool/seus again*
The way i resolved my problem was as follows:
-remove battery
-plug in charger
-re-insert battery.
This forced my battery to charge, but it also forces the battery to say it is 88% charged (even if it was flat to begin with)
i don't know if this will work for you - or even if you should try it.
PLEASE, ONLY TRY THIS AS A LAST RESORT AND ONCE AGAIN - I AM NOT RESPONSIBLE IF YOUYR PHONE EXPLODES AND I DO NOT RECOMMEND THIS METHOD AS IT MAY DAMAGE EITHER PHONE OR BATTERY
hi all i bought defy about a year ago as a second phone from ebay with cm7 installed.last week i purchase another phone and give my 7 years old daughter. however i reset everything and phone turn old version blur mod then stuck on m logo i download rom and sort the problem.
real problem starts now i try to install cm 9 download all required files wiped the phone and install the rom however it didn't restart stuck on black screen and only white led when connected with usb also didn't connect or recognized by rds lite.I found tread battery wake up from i think was ''mggrager'' or something else finally rds recognized the phone and install another sbf but still stays same as black screen and white.i read so many threats on this side or others and each i installed custom roms without clearing cache
battery replaced with replacement battery also original
all drivers installed
it doesn't respond any buttons or usb connection
rds only with battery jump
please help what to do
I'm having the same problem as you are, i believe... I had cm11 (or 10, not sure) installed for about a month now (back in december) .... Went on a trip, and when coming back my phone battery ran out at the airport... I take my phone home, not really giving it much importance, and i noticed it would never charge and/or turn on, and that when I connect it to the pc, nothing happened other than the white led coming on.. RSD won't recognized it...
So i found out i had to charge the battery manually, and used a Universal Charger... Still, no recognition by RSD Lite...
Finally, i found a way:
1. Open RSDLite
2. Connect phone (no battery on it)
3. While holding Power + Vol Up, put the battery in
4. RSD will recognize your phone!
Problem is, it recognizes my MB525 as "S Flash OMAP0360"
And when i try to flash a .sbf i used previously to recover my phone (had bricked it by trying to change ROMs in a sloppy manner), it seems to flash smoothly, but when it's going to reboot the phone, the progress goes up to 100% and then asks me to reboot it manually.. I read somewhere that to fix that i should take the battery out, disconnect the phone, put it back in, and make RSD recognize it like i mentioned before...... and after RSDLite says flashing is PASSED, the phone still won't turn on... I have tried at least three times and gotten the same result... Help?
I don't know if i should make a thread of my own.. i think we have the same problem, and i REALLY need my phone back.. so i guess we could just help each other fixing it somehow....
The SBF i am using (because it helped me save my phone before) is:
JORLA_U3_3.4.2_107-9_SIGNED_USAJORDMR1B25TIGCOLA01E.0R_JORLAFROTIGCOLA_P009_A002_M010_HWp3_WIG146037_Service1FF.sbf
EDIT: Also, i read somewhere that when all you get is the white led (when connecting to PC) it means that your battery is not charged enough for flashing.. ?
i already tried several times this method however no luck i am really not sure what to do any more i think only option try to find latest rom or first rom then try again if any luck will update and give the links
pasha543 said:
i already tried several times this method however no luck i am really not sure what to do any more i think only option try to find latest rom or first rom then try again if any luck will update and give the links
Click to expand...
Click to collapse
bump 4 help
Reposting it here, since this is the Lenovo sub-forums. Probably may find more help here.
I was using the Allegro ROM for the A1000G and it was running fine and dandy without any problems. Last night I tried installing a game and after I restarted it, it didn't turn on. I thought that maybe the device had low battery or something. So I plugged it in and let it charge for an hour and it still didn't turn on. Than I let it charge overnight and in the morning, it still doesn't turn on. So I tried to flash the Stock ROM for Lenovo a1000g and I got an error saying the storage was different or something - Error 3182 Message: BROM ERROR: S_STORAGE_NOT_MATCH (3182) [Edit - Tried to find the error, this is the one]
It was probably because the Allegro ROM was installed before it stopped working. So after that failed attempt at Flashing the Stock ROM - I don't get the battery indicator anymore and no matter what I try inside SP Flash Tool, it doesn't detect the device and the flashing process doesn't work. I tried installing and uninstalling all the MTK and Mediatek drivers but still not working. It shows up as MediaTek DA USB VCOM (Android) but it doesn't disappear, unless I remove the usb cable.
Before when I flashed the Allegro ROM and as seen across other youtube tutorials and guide, the device would show up for 2-4 seconds before disappearing and the SP Flash Tool would start working. Now it is just blank and the MediaTek DA USB VCOM (Android) doesn't go, no matter what.
Please, I would appreciate help. Since I don't have much knowledge regarding this. What must I do? I am depending on you guys.
~Aaron.
Bump. Please someone help.
__PUMA__ said:
Bump. Please someone help.
Click to expand...
Click to collapse
Thread closed as duplicate. I have left this one open
https://forum.xda-developers.com/th...p-lenovo-a1000-g-indian-version-hard-t3630644
but closed the others. Please do not make any more duplicates
Sawdoctor