[Custom] Pre jailbreak rom for (Asia SEA HD7 only) - HD7 Windows Phone 7 Development

Edit : (download)
RUU Schubert hTC Asia SEA WWE 1.57.728.02 Radio 5.52.09.16 22.33a.50.10 Signed SCHUBERT TEST jailbreak.rar
works on my Asia hd7..have not tested on other region phones. Do so at yr own . If it cannot be flashed, then the update will not continue so dont worry about bricking
Hi there frens, i have accidentally made a new technique for jailbreaking while playing around with ngh and spl files. it does not actually install any rom into yr device but prepares yr mango official to be jailbreaked by Cotulla DFT
the rom is based on 7004 test rom with OSPL 1.20 , with radio 5.51 from nodo,
when flashing this rom , it will get to 100% in romupdate utility u will get a error ( corrupt image)
but thats ok and u will be stuck in tri colour bootloader with the 1.20 Installed
At this point Run DFT RSPL on it and it will show cotulla ( jailbroken)
then u can install any custom ROm u want
will upload the package soon ..
so u may be asking whats the point of this>
1) allows u to skip extra step of flashing previous nodo stock rom, and allows direct flash of any rom u want after running RSPL
2) directly jailbreak
3) 5.51 radio after flashing custom rom which has batter battery life than the 5.69 mango radio
4) if u cant find SPL supported in DFT , ( 1.20 is supported)
i have confirmed this because this 5.51 radio while i was running on nodo gave me great battery life compared to the 5.65 and 5.69 radios which are faster but at the same time power consumption goes up

When you flash RSPL from the tricolour screen, it should show Cotulla anyway, but just for the first time: check after a soft reset.

i am not a developer or expert..
this si th ebest i can get.. will upload the files and if someone were to pick up on it
we can use it as a base to directly flash custom rom with custom NBH file

Magpir said:
i am not a developer or expert..
this si th ebest i can get.. will upload the files and if someone were to pick up on it
we can use it as a base to directly flash custom rom with custom NBH file
Click to expand...
Click to collapse
I've never tried but i think that, if you just use RSPL without HSPL, you can flash a ROM (one at time, of couse, because after that you'll have to RSPL again)

Cero92 said:
I've never tried but i think that, if you just use RSPL without HSPL, you can flash a ROM (one at time, of couse, because after that you'll have to RSPL again)
Click to expand...
Click to collapse
well i know that...
what i meant is those who downgrade and flash bootloader again to jailbreak yr phone

So you flashed hspl while in bootloader... Ok... Can do that turning off phone then turn back on while holding volume down.
I'm missing the point. Your allowed to flash custom roms with RSPL/HSPL that's the point of it.
I think your lost.
Edit: Oh I get it now. Your doing this from an official mango rom with the locked bootloaders that don't have a RSPL/HSPL yet. Ok
Sent from my HD7 T9292 using XDA Windows Phone 7 App

reeg420 said:
So you flashed hspl while in bootloader... Ok... Can do that turning off phone then turn back on while holding volume down.
I'm missing the point. Your allowed to flash custom roms with RSPL/HSPL that's the point of it.
I think your lost.
Edit: Oh I get it now. Your doing this from an official mango rom with the locked bootloaders that don't have a RSPL/HSPL yet. Ok
Sent from my HD7 T9292 using XDA Windows Phone 7 App
Click to expand...
Click to collapse
If u bootloader is the latest ( 4.5 SPL) , then u cant jailbreak it yet. so need to replace the bootloader with one of the SPL supported under DFT
yes but u need a full flashing rom( complete with wrappers and rom update utility) which is compatible with yr device region
since 7004 is the one i can find while searching online for my device
i just replaced the SPL & NBH from a 5.51 radio rom package from one of the ansar releases and replaced the ones found in the 7004 rom package
the process returns an error obviously because 7004 does not have a 5.51 radio which is based on later OS updates
this error simply means the OS has not been flashed.

tha package is ready for download

Related

Cannot uninstall HSPL after installing 1.66 wwe rom

My hd2 bricks after i tried uninstalling hspl with the help of stock rru_signed.nbh file. it is not working now. just a traingle with ! this coming.
any help.. hd2 i have is a vodafone uk stock rom.
mon_money said:
My hd2 bricks after i tried uninstalling hspl with the help of stock rru_signed.nbh file. it is not working now. just a traingle with ! this coming.
any help.. hd2 i have is a vodafone uk stock rom.
Click to expand...
Click to collapse
You must use a vodafone stock ROM then - the 1.66 HTC ROM flashes the stock SPL
which does not fit your CID, therefore you get the triangle.
thx for replying.
I had stock rom 1.48 before and then i installed HSPL so that i can install Stock 1.66 wwe rom into my hd2. It was a successful action. Rom installed and worked correctly without any problem.
But problem arise when I tried to uninstall the HSPL to original spl. I renamed the 1.66 rom .nbh file to LEOIMG.nbh and converted the card format into fat32 also.
when i inserted the card into hd2 and turned it on whilst pressing down volume button. its started into boot loader program and den asked me to press power button to start the process.
And then it ended with an error.. 00028002 NOT ALLOW something like that. which is for Invalid vendor ID..
Please help..
how to return to original spl with the latest 1.66 wwe rom.
thx in advance..
tictac0566 said:
You must use a vodafone stock ROM then - the 1.66 HTC ROM flashes the stock SPL
which does not fit your CID, therefore you get the triangle.
Click to expand...
Click to collapse
don't think you can, HSPL has to stay on...could be wrong though...
why do you want to take it off?
mon_money said:
thx for replying.
I had stock rom 1.48 before and then i installed HSPL so that i can install Stock 1.66 wwe rom into my hd2. It was a successful action. Rom installed and worked correctly without any problem.
But problem arise when I tried to uninstall the HSPL to original spl. I renamed the 1.66 rom .nbh file to LEOIMG.nbh and converted the card format into fat32 also.
when i inserted the card into hd2 and turned it on whilst pressing down volume button. its started into boot loader program and den asked me to press power button to start the process.
And then it ended with an error.. 02800 something like that. which is for Invalid vendor ID..
Please help..
how to return to original spl with the latest 1.66 wwe rom.
thx in advance..
Click to expand...
Click to collapse
Actually, you did everything correctly... except that you should use the stock ROM for your device, which is vodafone branded, isn´t it?
BTW, did you check the SPL version already? Because it might be already back to stock SPL, but then, you won´t be able to flash an original HTC ROM.
Being back at stock SPL (with vodafone CID) and trying to flash/launch an official HTC ROM on the branded device results in what you write!
Hmm.. is there any harm if i don't remove HSPL??? as m still trying to make my HD2 working..
error coming is 00028002 NOT ALLOW
EddyOS said:
don't think you can, HSPL has to stay on...could be wrong though...
why do you want to take it off?
Click to expand...
Click to collapse
mon_money said:
Hmm.. is there any harm if i don't remove HSPL??? as m still trying to make my HD2 working..
error coming is 00028002 NOT ALLOW
Click to expand...
Click to collapse
Get the original 1.43 vodafone UK ROM from here, and repeat what you did.
Follow the first link, select 1.43, then obviously the vodafone ROM.
EDIT PS:
In case you want to keep the stock SPL, but upgrade to the 1.66 HTC ROM, you must do this using SSPL (search for this here in the forum).
As of today, there is no other way of getting the stock SPL back than flashing your original ROM.
BIG thank you .. it is working now with the stock 1.43 rom.. and yes u are right.. it was showing me again 1.42 spl after uninstalling the HSPL.
u saved my hd2.. thx once again for ur great help..
tictac0566 said:
Get the original 1.43 vodafone UK ROM from here, and repeat what you did.
Follow the first link, select 1.43, then obviously the vodafone ROM.
EDIT PS:
In case you want to keep the stock SPL, but upgrade to the 1.66 HTC ROM, you must do this using SSPL (search for this here in the forum).
As of today, there is no other way of getting the stock SPL back than flashing your original ROM.
Click to expand...
Click to collapse
tictac0566 said:
Get the original 1.43 vodafone UK ROM from here, and repeat what you did.
Follow the first link, select 1.43, then obviously the vodafone ROM.
EDIT PS:
In case you want to keep the stock SPL, but upgrade to the 1.66 HTC ROM, you must do this using SSPL (search for this here in the forum).
As of today, there is no other way of getting the stock SPL back than flashing your original ROM.
Click to expand...
Click to collapse
Hi
Thanks for the link, however the 1.43 ROM is corrupt, I have tried downloading several times. I try to extra the RUU_Signed.nbh with winrar but it fails, the 1.66 and 1.72 Vodafone ROMs extract fine.
Basically I am trying to restore a Vodafone HD2 to stock ROM+SPL, reason being the phone they sent on an insurance replacement is rubbish e.g. the touchscreen isn't responsive. I tried changing to a custom ROM also Vodafone 1.66 and 1.72 to see if the problem would be fixed but it didn't help.
Now I just need to send the phone back for another replacement.
Does anyone have an alternative link for this 1.43 ROM?
I am having a similar issue.
I am trying remove HSPL, I have copied the .nbh file over to the SD already formatted as FAT 32 - I'm using my original ROM.
(RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Shp )
Also tried with ( RUU_Leo_HTC_WWE_1.43.405.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship )
When I start with volume down pressed, I get a message saying " Upgrade ROM code error please try again " then the multi coloured screen with SPL-1.42.0000 XE.
Please help, I fear I have broken my phone ...
chrisukhd2 said:
(RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Shp )
Also tried with ( RUU_Leo_HTC_WWE_1.43.405.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship )
Click to expand...
Click to collapse
Then your phone is probably provider rom locked.
SPL-1.42.0000 XE.
Click to expand...
Click to collapse
HSPL is already removed, which is why the WWE roms don't work. You need to find your provider released rom, or (far easier) run hspl2, choose 1.42.hspl, flash either of teh roms you mentioned above by USB, run hspl2 again, choose 1.42.0000 and done.
samsamuel
Thanks for the reply.
I can't use HSPL2 as the phone doesn't sink to my PC as it's stuck on the tri colour screen. Unless there is a way of doing this from the memory card.
I'm pretty sure my stock ROM was 1.43, which I have downloaded but can't re flash?.
I guess I need to download a 1.42 O2 ROM from somewhere?
chrisukhd2 said:
samsamuel
Thanks for the reply.
I can't use HSPL2 as the phone doesn't sink to my PC as it's stuck on the tri colour screen. Unless there is a way of doing this from the memory card.
I'm pretty sure my stock ROM was 1.43, which I have downloaded but can't re flash?.
I guess I need to download a 1.42 O2 ROM from somewhere?
Click to expand...
Click to collapse
No need to sync to pc. In bootloader, connect usb cable - when USB shows on the screen then run HSPL2
ClydeB1 said:
No need to sync to pc. In bootloader, connect usb cable - when USB shows on the screen then run HSPL2
Click to expand...
Click to collapse
pre - and indeed - cisely
OK this is using the 1.48 ROM
Used HSPL2 and hacked to 1.42.hspl, pressed power to start update image, and the ROM loaded but then goes back to the tri colour screen again. So I ran flashed through USB 1.48 ROM and got " Invalid Vendor ID " ?
I tried HSPL2 again to hack to 1.42.0000 and then re-flash through USB and got " invalid vendor ID again "
I even tried with HSPL I had before and the same result.
Argghhhhhh
What can I be doing wrong here ?
Working now
I downloaded the latest O2 ROM 1.72.0 etc and it's working now.
Thanks again guys, you helped me a lot
Once more thing my phone now say's it has SPL-1.66 - I guess when unlocking using HSPL2, I now need to choose 1.66.000?
mon_money said:
My hd2 bricks after i tried uninstalling hspl with the help of stock rru_signed.nbh file. it is not working now. just a traingle with ! this coming.
any help.. hd2 i have is a vodafone uk stock rom.
Click to expand...
Click to collapse
1. download stock ROM
2. unpack/unzip and place ruu_signed.nbh and ROMUpdateUtility in sd card
3. make sure you have >50% battery life
4. with the device turned off, put sd card in
5. enter boot loader, device will automatically detect ROM file in sd card and
then will install this, it will install stock spl as well so hspl will be removed
chrisukhd2 said:
OK this is using the 1.48 ROM
Used HSPL2 and hacked to 1.42.hspl, pressed power to start update image, and the ROM loaded but then goes back to the tri colour screen again. So I ran flashed through USB 1.48 ROM and got " Invalid Vendor ID " ?
Click to expand...
Click to collapse
sounds like you tried to flash over sd card, which as any fule kno first thing it does is resets the spl, so hspl is no longer installed so the rest of the flash fails.
I tried HSPL2 again to hack to 1.42.0000 and then re-flash through USB and got " invalid vendor ID again "
Click to expand...
Click to collapse
because its .0000
I even tried with HSPL I had before and the same result.
Argghhhhhh
Click to expand...
Click to collapse
used sd card again eh?
1 - boot the phone to bootloader. (Three coloured screen)
2 - run hspl2, choose whatever spl you like SO LONG AS it ends HSPL.
3 - when the phone reboots, keep volume down pressed to re enter bootloader
4 - run your rom flash over USB
5 - phone should now boot normally.
6 - if you now want to remove hspl again, re run HSPL2 and choose the spl you want, ENDING IN .0000
samsamuel
Yes Doh - I was flashing from SD and then trying to flash through USB. It all makes sense now. I got around it though by using the new O2 ROM that's just been released so I didn't need to unlock to bring my phone back to life.
Anyway it's all working fine now with the stock 1.72 O2 ROM, just flashed with HSPL2 and re-installed the Energy ROM.
Thanks again for all the help.
ahh good.
Its a good idea if you flash fairly regularly to do your flashing from bootloader, that way you are visually aware of your spl at every step. just get used to holding vol down as it reboots and you can do the whole thing, hspl, rom, radio, without ever having to pull the battery. just keep booting to tri colour till its done.

Telstra Rom - not flashing

Folks,
HD2 from Telstra ( 2nd May ) running 1.66. Tried flashing it with 1.48 and 1.43 Rom's -- so I could then go to HSPL and a custom Rom, but no luck.
The Rom Update Utility starts and tells me I have image version 1.72.841.0, I click to update to 1.43.405.1 ( or 1.48 - have tried both ), then the 4 colour screen which notes 1.66. Then it goes to a HTC screen with a deployment bar, gets to only 1%.......then boom - error 294 invalid vendor id.......
What am I missing here ??
you need to flash thedowngrade from sd card, then you can hspl, and THEN flash from usb
At least your effort got that far.... i couldnt even see the zip open.
OS 5.2.21869
Manila 2.5.20121431.1
Rom 1.72.841.0
If someone can confirm what I need to do with what i'd REALLY appreciate it.
Have the backup rom just incase already.
you missed out all the important info.
what zip can't you open? what phone? what you trying to achieve?
assuming telstra like the op,
1 right click the telstra 1.4 rom .exe choose unzip here, or extract here
2 find ruu signed.nbh copy it to sd card rename it leoimg.nbh
3 phone off hold vol down, tap and release power, keep holding voldown till you see three coloured screen, should quickly change grey and start a card flash.
4 when complete and phone restarts hold vol down to re enter bootloader
5 run hspl as administrator using a usb port round the back of the pc,
6 when it completes, and phone reboots, enter bootloader yet again, and check that it says spl 1.42.hspl.
now, so long as you don't sd card flash hspl will stay and protect against bad flashes, flash what you like.
tmenyweather said:
Folks,
HD2 from Telstra ( 2nd May ) running 1.66. Tried flashing it with 1.48 and 1.43 Rom's -- so I could then go to HSPL and a custom Rom, but no luck.
The Rom Update Utility starts and tells me I have image version 1.72.841.0, I click to update to 1.43.405.1 ( or 1.48 - have tried both ), then the 4 colour screen which notes 1.66. Then it goes to a HTC screen with a deployment bar, gets to only 1%.......then boom - error 294 invalid vendor id.......
What am I missing here ??
Click to expand...
Click to collapse
What 1.48 and 1.43 roms did you try? They need to be Telstra roms, as you can't just use any 1.48 or 1.43 rom and this is what is causing the invalid vendor id error. Once you are back to 1.42.0000 spl (after flashing a telstra rom) you can then run hspl and are then free to flash what ever your heart desires.
I have a Telstra HD2 as well (1.66)...got it recently and will flash it soon.
I don't understand the original poster's concern - why go through all that to flash HSPL, when apparently HSPL2 can be easily flashed over 1.66...which allows you to further flash any ROM ??? Is there a benefit of HSPL over HSPL2 that I am missing?
Thanks in advance
edit: my bad, just read in the HSPL thread that HSPL2 does not work with the telstra hd2.
TyII said:
I have a Telstra HD2 as well (1.66)...got it recently and will flash it soon.
I don't understand the original poster's concern - why go through all that to flash HSPL, when apparently HSPL2 can be easily flashed over 1.66...which allows you to further flash any ROM ??? Is there a benefit of HSPL over HSPL2 that I am missing?
Thanks in advance
Click to expand...
Click to collapse
keep reading, you still have lots to learn, hspl2 doesn't work on telstra.
Oh, my spl is 1.66.0000
I understand I must use HSPL (not HSPL2) on a Telstra ph. but can anyone recommend which rom to use? I've been reading for two days solid and can't decide!
I've copied all the guides etc so hopefully won't have a prob'... am just worried about warranty protection etc if it all goes pear shaped... i just want all this B.S. bloatware OFF MY phone!!!
Thanx in advance once again
I am in the same position, my Telstra ROM is 1.72 running SPL 1.66.0000.
HSPL utility tells me that "Model ID is invalid" or something like that.
okay, one more time.....
only the original hspl works on telstra,
hspl2 does not work. (bad model ID)
you need to downgrade to a 1.4 rom with spl 1.42.0000.
so, get the original telstra 1.49.8xx rom from HERE (registration required)
when its downloaded, move it to its own folder somewhere, then right click the .exe file and choose extract here. (if that option isnt available, install winrar)
when it has extracted, find teh file RUU_Signed.nbh, copy it to your sd card and rename it leoimg.nbh
restart your phone in bootloader mode, it should detect the leoimg.nbh and start to flash
this will reset your spl to 1.42.0000 and now you can use HSPL, and then flash any rom you like.
Thanks for the link to HTCpedia mate. I'd actually just found it myself by performing a thread search on the "Official HTC ROM's" thread. Downloading now.
Stupidly I've had problems after problems trying to get HSPL on my device. I actually started out on this ROM (1.49.x with SPL 1.42.0000). First I tried flashing from my Vista x64 machine, both HSPL2 and HSPL with errors, in my haste I thought I might need update to the latest Telstra ROM 1.72.x with SPL 1.66.0000 so I could use HSPL2 when in actual fact I just had the x64 USB driver problem, of course then the upgrade still didn't allow me to flash and made my situation harder as I had to find this original ROM again to downgrade.
Anyways I hope this works!
It works!
- flash rom back to 1.49.x with SPL 1.42.0000
- run HSPL with device connected via USB
- flash radio using CustomRUU
- flash ROM using CustomRUU
@rainey06au what Radio do you use with your Telstra HD2?
Got my Telstra HD2 running 1.49 last week and it's my first play with Windows Mobile .. couldn't wait to clear the Telstra image from the phone as my provider is Three.
Did plenty of reading and all the posts said to use the original HSPL first, this worked perfect first go.
Once done I tried the new Artemis_v110 rom, was very impressed except experienced 2 to 3 random reboots a day, even more while in YouTube player. Everything else woked well, reception, battery life, and clarity while on calls.
Decided yesterday to try another rom, first cleared all using Task29 format, then loaded HyperROM Ultimate v9.00 WM6.5.X but this didn't get through the first boot .. possibly due to radio required.
Now have flashed back to 1.48.4052 until I research some more.
Anyone recommend a rom and suitable radio for the Telstra HD2, anyone with Three?
Thankx
Thanks. Works a treat!
I knew I had to downgrade but couldn't find an old Telstra ROM.
samsamuel said:
you missed out all the important info.
what zip can't you open? what phone? what you trying to achieve?
assuming telstra like the op,
1 right click the telstra 1.4 rom .exe choose unzip here, or extract here
2 find ruu signed.nbh copy it to sd card rename it leoimg.nbh
3 phone off hold vol down, tap and release power, keep holding voldown till you see three coloured screen, should quickly change grey and start a card flash.
4 when complete and phone restarts hold vol down to re enter bootloader
5 run hspl as administrator using a usb port round the back of the pc,
6 when it completes, and phone reboots, enter bootloader yet again, and check that it says spl 1.42.hspl.
now, so long as you don't sd card flash hspl will stay and protect against bad flashes, flash what you like.
Click to expand...
Click to collapse
I am also using Telstra HD2 and recently flashed it with Miri Rom. I like Miri because it doesn't have any customization. It has many versions to choose from, with and without Sense UI. It also retain all the original WM icons and themes which I like.
But like all ROMs, I do experience reboot but only once so far with the new version of Miri v17. One thing to note is the Radio version for the ROM. Make sure you flash the exact correct radio version, down to the sub version, e.g. 2.07.50 is recommended for Miri and not 2.07.51 (which is the Telstra radio version).
Another advise is always flash from pc, not SD card as I have experienced bad flash using SD card.
Hope this helps. Miri is only available from the HTCPedia site.
Yep my radio version is also 2.07.50. I get good battery life out of it using CleanEX_UDT HyperROM Ultra v9.00 (6.5).
I use Lia Glass ROM and FallOut Theme.
Interestingly this ROM and radio has only unlocked 455.54MB RAM, not the full 576MB. There are threads about this and getting the right combo will unlock the remaining RAM and/or improve battery performance.
I am using Radio 2.08.50.05.
Anyone else have the same experience?
ajt320 said:
I use Lia Glass ROM and FallOut Theme.
Interestingly this ROM and radio has only unlocked 455.54MB RAM, not the full 576MB. There are threads about this and getting the right combo will unlock the remaining RAM and/or improve battery performance.
I am using Radio 2.08.50.05.
Anyone else have the same experience?
Click to expand...
Click to collapse
look in settings about phone hardware info ram size.
I bet it says 576
that's cos the hardware takes 128 for graphics.
look st a standard rom and hardware will show 448 whilst total available will show 336
Thanks samsamuel.
Hardware info does in fact say 576MB RAM
Thanks for the explanation - slowly but surely getting my head around the intricacies of the device

[Q] Flashing phone to stock ROM ?

Hi how do i go about flashing my HD2 back to stock English: 3.14.405.2 ROM ?! as i'd like to sell it now. i have an artemis rom, cotulla HSPL 2.08 and a splash screen from an old chucky ROm i'd like to get rid of !!
so how do i do this safely ?cheers dom
p.s will i still be able to boot into an sd build of android from a stock rom ??
into bootloader, 'serial' --> 'USB'
run hspl4 choose 2.08.0000 (or 3.03.0000, or in fact any that end .0000, teh next step will upgrade it anyway, so long as it ends .0000)
into bootloader, 'serial' --> 'USB'
run 3.14 rom .exe
done.
(this assumes you have the correct 3.14 rom, not just the default stock rom. i.e if your phone is from o2 you need the o2 3.14 rom)
PS yes
Oh right thank you for your quick reply! I think I'll just flash a stock rom so I can sell the phone as unlocked! Thanks again for your help! !!
Sent from my HTC Desire using XDA App
onisuk said:
so I can sell the phone as unlocked!
Click to expand...
Click to collapse
you cant relock an unlocked phone anyway, no matter what you flash.
Dont confuse sim lock and rom lock, Totally unconnected.
a sim unlocked phone will still need hspl to flash, and a flashed phone isn't sim unlocked.
samsamuel said:
into bootloader, 'serial' --> 'USB'
run hspl4 choose 2.08.0000 (or 3.03.0000, or in fact any that end .0000, teh next step will upgrade it anyway, so long as it ends .0000)
into bootloader, 'serial' --> 'USB'
run 3.14 rom .exe
done.
(this assumes you have the correct 3.14 rom, not just the default stock rom. i.e if your phone is from o2 you need the o2 3.14 rom)
PS yes
Click to expand...
Click to collapse
oh crap.
i just flashed straight back to stock without doing any of this... have i screwed up?
Also i did it because it keeps crashing and overheating so i was going to try it on stock and if it kept doing it i was going to send it back to htc - will they be able to tell i tried a custom rom?
(seems to be working fine though)
EDIT:
another question - will this have changed my radio back to stock too - or do I have to do this manually?
where can i download the new stock rom as the HTC site says its now for my phone....(probably because it was an O2 branded rom before)
theres an O2 update as well on the HTC website?
Otherwise the latest ones are on here:
http://forum.xda-developers.com/showthread.php?t=623283
I managed to sort mine - turns out you have to do it via SD and it does everything bootloader, ROM and radio. (although it failed the first time and i almost made a mess in my trousers)
If anyones interested the instructions are (taken from HSPL4 app):
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
I also formatted the SD before copying it over.
No there was only one for t mobile !
cheers for the link matey
yea its odd that, the o2 3.14 rom is there via direct link, has been since saturday, but still doesn't show if you navigate to the rom updates page on htc.uk
ok updated the hspl fine...but when i try to flash the new WWE rom i get an "invalid vendor id" at 1% and the flash fails
righty all sorted ! the O2 rom was on the UK site i was being dumb and look on htc Europe site !
all flashed and working fine now

[ROM]YardieROM v3(RUU_Mozart_S_HTC_Europe_5.01.401.04_5.71.09.02a _22 .51.50)Unlocked

Here is the new RUU_Mozart_S_HTC_Europe_5.01.401.04_5.71.09.02a_22 .51.50, unlocked and ready to go:
http://www.4shared.com/file/LgeeWQfG/Mozart_YardieROM_v3_501_7720.html
Changelog:
Developer Unlocked,max apps and prevent relock.
Custclear.provxml added to /windows
HTC theme replaced with grey theme
Alert tones 1-3 replaced with "you got Mail"etc
Internet explorer first run to google.
Added XBMods certs for update cabs.
SPL removed.
Instructions-
Be aware of XSPL issue with Mozart 4.XX & 5.XXroms, if required flash back to a NoDo rom before flashing XSPL.
1.Enter bootloader(Power on& vol-)
2.Flash RSPL(downgrade to NoDo if on 4.xx or 5.xx SPL)
3.Flash YardieROM using Rom Update Utility.
Respects out to Cotulla&DFT,bepe,ansar,XBMod,Football,Marvin_S,DaG,AnDim ,Ted973,Heathcliff74,airextreme&ceesheim for all the work they have put into WP7 development and creating the tools for us to play with.
--Reserved--
thank, after flashed will change the spl version? or stay with old hspl?
hengmy said:
thank, after flashed will change the spl version? or stay with old hspl?
Click to expand...
Click to collapse
It will remain with your original spl
Add Lang.
Is this rom able to work with RegistryEditor 1.2.0.0?
But it seems unable to save string I added.
thx
ps. I've managed to add Chinese to this ROM.
kevin3688 said:
Is this rom able to work with RegistryEditor 1.2.0.0?
I'm trying to add Chinese with RegistryEditor 1.2.0.0.
But it seems unable to save string I added.
thx
Click to expand...
Click to collapse
RUU_Mozart_S_HTC_Europe_5.01.401.04_5.71.09.02a_22 .51.50
Europe region... it means there is no chinese language pack in it.
The Registry Program 1.2.0 works
I need original theme, the new theme and Alert tones is not good.
I tried to flash your Rom it struck at 7%, luckily it didn't change my bootloader, back to Ansar's, thanks anyways.
the charging sound had been changed to "you got a voice message" not a big issue but.......
yardie.spike said:
It will remain with your original spl
Click to expand...
Click to collapse
Not good ... Is it reverssible ?
Caramel said:
Not good ... Is it reverssible ?
Click to expand...
Click to collapse
Whats not good?.....it means you can use XSPL and flash the latest roms rather than brick your Mozart.
Cheers Yardie boy
Loading it now
Be carrefull !!!
Begin flash with HSPL 1.32
Freeze while flashing
Reboot in bootloader to restart the flash.
Unable to flash again, Why ?
This rom put my Mozart in SPL 5.1, unable to go back in HSPL.
Caramel said:
Be carrefull !!!
Begin flash with HSPL 1.32
Freeze while flashing
Reboot in bootloader to restart the flash.
Unable to flash again, Why ?
This rom put my Mozart in SPL 5.1, unable to go back in HSPL.
Click to expand...
Click to collapse
No issue with HSPL 1.32 for me...no change in SPL either, what did you do different?
You could alwasy load an OSPL then put RSPL/HSPL on again.
The only little snag I noticed was connection set-up kept launching every reboot, which was resolved by deleting it...

Trouble finding TELUS 1.52 SPL

I'm sick and tired of not having tethering or custom alerts, so I want to install a custom rom on my surround. I'm trying to downgrade my SPL to 1.52 so I can install HSPL, but I can't find a TELUS one anywhre.
The only one I have seen is Ansar's, but his links are dead. I can't post the links yet as i don't have 10 posts.
Does anyone know of where I can get the stock TELUS 1.52 SPL from, or where I can get Ansar's?
Thanks in advance!
I have two Telus Surrounds and I used this rom from Cingular to roll back the spl so that I could unlock it with DFT HSPL Version 3, and then you can load any custom rom you want. If you can't load the rom you might have to use the gold card with a memory stick.
http://www.filefactory.com/file/b48...S_1.03.502.07_5.51.09.06_22.30.50_RELEASE.exe
http://forum.xda-developers.com/showthread.php?t=1597837
CrazyTegger said:
I'm sick and tired of not having tethering or custom alerts, so I want to install a custom rom on my surround. I'm trying to downgrade my SPL to 1.52 so I can install HSPL, but I can't find a TELUS one anywhre.
The only one I have seen is Ansar's, but his links are dead. I can't post the links yet as i don't have 10 posts.
Does anyone know of where I can get the stock TELUS 1.52 SPL from, or where I can get Ansar's?
Thanks in advance!
Click to expand...
Click to collapse
http://dl.vmall.com/c0m2gktk1f
mcsc said:
I have two Telus Surrounds and I used this rom from Cingular to roll back the spl so that I could unlock it with DFT HSPL Version 3, and then you can load any custom rom you want. If you can't load the rom you might have to use the gold card with a memory stick.
http://www.filefactory.com/file/b48...S_1.03.502.07_5.51.09.06_22.30.50_RELEASE.exe
http://forum.xda-developers.com/showthread.php?t=1597837
Click to expand...
Click to collapse
I tried that one but it said invalid vendor id. I assumed that was because I had a Telus phone and not a Cingular one.
I should mention that I'm running 7.8 with bootloader 4.22.2250.0(129185) and firmware 2250.21.40200.661
ofIIns and
jimmy110 said:
link
Click to expand...
Click to collapse
I was successfully able to download and install the rom onto my phone. Now it's readying SPL 1.4.2250.2(113577) and then tried to install RSPL, but the phone would not reboot. I tried resetting the phone as some others indicated, but to no avail.
I then upgraded the phone to NODO using cab sender successfully and tried to RSPL, again the phone wouldn't reboot after completion.
Any ideas?
CrazyTegger said:
I was successfully able to download and install the rom onto my phone. Now it's readying SPL 1.4.2250.2(113577) and then tried to install RSPL, but the phone would not reboot. I tried resetting the phone as some others indicated, but to no avail.
I then upgraded the phone to NODO using cab sender successfully and tried to RSPL, again the phone wouldn't reboot after completion.
Any ideas?
Click to expand...
Click to collapse
Great, now I can't even upgrade my phone using zune or cab sender anymore... I'm stuck on NODO.
Does anyone have the STOCK Telus ROM, and not the modified one like the one provided?
yup I have it
CrazyTegger said:
Great, now I can't even upgrade my phone using zune or cab sender anymore... I'm stuck on NODO.
Does anyone have the STOCK Telus ROM, and not the modified one like the one provided?
Click to expand...
Click to collapse
I am uploading it now
Hold that thought...got a free file host that doesn't suck? if not PM me I will stick it on my private FTP
rob243 said:
I am uploading it now
Hold that thought...got a free file host that doesn't suck? if not PM me I will stick it on my private FTP
Click to expand...
Click to collapse
PM Sent.
CrazyTegger said:
I was successfully able to download and install the rom onto my phone. Now it's readying SPL 1.4.2250.2(113577) and then tried to install RSPL, but the phone would not reboot. I tried resetting the phone as some others indicated, but to no avail.
I then upgraded the phone to NODO using cab sender successfully and tried to RSPL, again the phone wouldn't reboot after completion.
Any ideas?
Click to expand...
Click to collapse
Telus rom is a test rom
you flash telus just to take its touch driver and radio
then you flash default shipped rom (delete SPL_Signed.nbh from shipped rom to save the drivers you got from telus)
then you can go with spl tools
thnx
jimmy110 said:
Telus rom is a test rom
you flash telus just to take its touch driver and radio
then you flash default shipped rom (delete SPL_Signed.nbh from shipped rom to save the drivers you got from telus)
then you can go with spl tools
thnx
Click to expand...
Click to collapse
When you say Flash Default Shipped ROM, are you meaning the TELUS one, or the Cingular one?
I then update using RUU or GoldCard?
CrazyTegger said:
When you say Flash Default Shipped ROM, are you meaning the TELUS one, or the Cingular one?
I then update using RUU or GoldCard?
Click to expand...
Click to collapse
The Default rom that you can name it shipped is Cingular
u use TELUS ROM when you have a trouble with touch driver ( like lock screen bug ) , or when u have trouble in call transmission driver ( making , reciving call problems )
note: u can't flash telus rom with goldcard method else you have a security unlocked bootloader !!
u can flash TELUS ROM with rom utility that come with it
after you take benefit of flashing telus, u cannot go with it, u have to return to Cingular one, note: delete SPL_signed.nbh from Cingular Rom to save drivers that u installed from TELUS, then you go with spl tools
sorry for my bad english
jimmy110 said:
The Default rom that you can name it shipped is Cingular
u use TELUS ROM when you have a trouble with touch driver ( like lock screen bug ) , or when u have trouble in call transmission driver ( making , reciving call problems )
note: u can't flash telus rom with goldcard method else you have a security unlocked bootloader !!
u can flash TELUS ROM with rom utility that come with it
after you take benefit of flashing telus, u cannot go with it, u have to return to Cingular one, note: delete SPL_signed.nbh from Cingular Rom to save drivers that u installed from TELUS, then you go with spl tools
sorry for my bad english
Click to expand...
Click to collapse
I don't quite understand. My phone was bought for, and is on the TELUS network. I had upgraded it to 7.8 using cab sender, but really wanted some features (Wifi Tethering, Custom Alerts), so I tried the custom ROM route.
The only thing I've been able to successfully install on it is the TELUS Test ROM, and upgrade it to NODO using Zune (Mango updates failed - I think because it wants a newer firmware, which I have the cab files, but they fail installing)
The Telus Test ROM that I had downloaded uses firmware 22.50.09.10402.661 and bootloader: 1.4.2250.2 (113577).
If I try to install RSPL/HSPL right now, the phone does not restart after completion, thus never gets into RSPL mode to do HSPL.
I recall trying to use RUU to put on Cingular ROM, however it always failed, I believe saying that Vendor ID is invalid.
I'm really frustrated with this, but I don't know how to move forward to install RSPL/HSPL.
CrazyTegger said:
I don't quite understand. My phone was bought for, and is on the TELUS network. I had upgraded it to 7.8 using cab sender, but really wanted some features (Wifi Tethering, Custom Alerts), so I tried the custom ROM route.
The only thing I've been able to successfully install on it is the TELUS Test ROM, and upgrade it to NODO using Zune (Mango updates failed - I think because it wants a newer firmware, which I have the cab files, but they fail installing)
The Telus Test ROM that I had downloaded uses firmware 22.50.09.10402.661 and bootloader: 1.4.2250.2 (113577).
If I try to install RSPL/HSPL right now, the phone does not restart after completion, thus never gets into RSPL mode to do HSPL.
I recall trying to use RUU to put on Cingular ROM, however it always failed, I believe saying that Vendor ID is invalid.
I'm really frustrated with this, but I don't know how to move forward to install RSPL/HSPL.
Click to expand...
Click to collapse
steps to solve all of your problem
cus your device originally on telus network , you cannot install Cingular while you have locked bootlooader
solution :
1- search in forums about , unlocking boot loder
2- unlock your bootloader ( you know that your bootloader is unlocked when u see on the top of your screen , "security unlocked" when you enter the boot screen (4 colored screen)
3- install Cingular ROM and you will succeed in that after u unlock your bootloader\
4- using spl tools now u can unlock spl to get HSPL
5- install cerebellum 7.8 ROM that will find all features enabled on it ( internet sharing , etc)
and you don't need zune update anymore
note: you will find it hard to unlock your bootloader but it worth try
search in other devices forums , all are same
jimmy110 said:
steps to solve all of your problem
cus your device originally on telus network , you cannot install Cingular while you have locked bootlooader
solution :
1- search in forums about , unlocking boot loder
2- unlock your bootloader ( you know that your bootloader is unlocked when u see on the top of your screen , "security unlocked" when you enter the boot screen (4 colored screen)
3- install Cingular ROM and you will succeed in that after u unlock your bootloader\
4- using spl tools now u can unlock spl to get HSPL
5- install cerebellum 7.8 ROM that will find all features enabled on it ( internet sharing , etc)
and you don't need zune update anymore
note: you will find it hard to unlock your bootloader but it worth try
search in other devices forums , all are same
Click to expand...
Click to collapse
I was under the impression that installing RSPL/HSPL was used to unlock the bootloader. Is this something different entirely?
CrazyTegger said:
I was under the impression that installing RSPL/HSPL was used to unlock the bootloader. Is this something different entirely?
Click to expand...
Click to collapse
RSPL/HSPL is unlock bootloader not deeply enough to allow you to change the hole operator ROM , (change from telus to cingular)
you have to full unlock bootloader
jimmy110 said:
RSPL/HSPL is unlock bootloader not deeply enough to allow you to change the hole operator ROM , (change from telus to cingular)
you have to full unlock bootloader
Click to expand...
Click to collapse
Are there any good keywords I can use? unlock bootloader htc surround isn't working for me.
CrazyTegger said:
Are there any good keywords I can use? unlock bootloader htc surround isn't working for me.
Click to expand...
Click to collapse
search for unlock bootloader generally not for htc surround ( surround is poorest forum )
and all are the same way
jimmy110 said:
search for unlock bootloader generally not for htc surround ( surround is poorest forum )
and all are the same way
Click to expand...
Click to collapse
I'm really not finding anything useful here... I see a lot for Android, but nothing for an HTC Windows Phone. Are you referring to an IMEI unlock? ChevronWP7? Unbranding? Interop Unlock? WP7 Root Tools?
Thanks
I've now managed to developer unlock my Surround. What's the next step from here?

Categories

Resources