Hi I tried to update the rom and now i'm unable to do anything
i can get it onto the tri colour screen with the following info
PB81100 HX-BC SPL-2.08.HSPL 8G XE CotullaHSPL 0x30
once i try to load anything else it get stuck in a new screen with this
LEOPB81100 HX-DC
cLK-1.6.5.0
HSPL 8G XX
Radio -unknown
boot recovery
boot sboot
continue normal boot
boot fail ! check boot/recovery partition try again!
tried to do all of these just returns me back here
i have printed a partition table and the largest size is
user data blocks 1960 size 245 mb
is my beloved leo destine for the bin??
help please
i don't think you bricked...just something got wrong with cLK. Try again every steps from task29
hi i tried task 29 but it just sits for ages and then comes up with an error message!
hi just tried it again, this time it loaded, but it now just shows the front HTC screen, whilst turning it on held the on key to try and get into cLK but nothing
of course, because task29 cleared cLK from nand...just flash cLK or magldr as usual, and then flash the recovery, and then install a rom from zip
sorry, just flash maglar v1.13, when it booted up it said kernel was missing??
trash2 said:
sorry, just flash maglar v1.13, when it booted up it said kernel was missing??
Click to expand...
Click to collapse
its normal after flashing mgldr. now you must find a rom. then make a cwm partition according to the needs of rom. then flash the rom from sd.
sorry to be a pain.
i wanted to put clk on but every time i go into usb flasher and try i get
An error has occurred
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (736)
Error Description: EnterBootloader missing
Info: .\RSPL\BootLoader.cpp (176)
i'm running window 7 does that make a difference
Flash clk from bootloader not magldr (but of course you knew this didnt you? having thoroughly read and understood the clk thread post 1, right?)
Related
An error has occurred
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (725)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (304)
How to fix this error please help.
I'm betting that's because you didn't read the first post for magldr 1.13 which clearly states run romupdateutility.exe to flash. I bet you ran daf.exe
faizan113 said:
An error has occurred
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (725)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (304)
How to fix this error please help.
Click to expand...
Click to collapse
it happend to me once too.. but that was becuase a txt file wasn't extracted
Hi Guys,
I have Energy.Leo.21683.Sense2.5.Cookie.Nov.02 currently running. Radio version perfect...
Everytime I use MAGLDR113 it reboots after i do the ROMUpdateUtility and does not go into the bootloader...
Any ideas?
I am going to try MAGLDR 1.11 now and see what happens.
@Clydeb1 when you said romupdate utility how to run that is it inside the magldr folder?
I found update utility ill try tommorow and btw when ill install magldr 1.1.3 will I have to reinstall nand android or not?
faizan113 said:
@Clydeb1 when you said romupdate utility how to run that is it inside the magldr folder?
I found update utility ill try tommorow and btw when ill install magldr 1.1.3 will I have to reinstall nand android or not?
Click to expand...
Click to collapse
If all you are doing is updating MAGLDR from an existing version to the latest version (1.13) then no, you won't have to reinstall anything afterwards. But, to be safe, I would still recommend doing a backup via CWM first.
deamace said:
Hi Guys,
I have Energy.Leo.21683.Sense2.5.Cookie.Nov.02 currently running. Radio version perfect...
Everytime I use MAGLDR113 it reboots after i do the ROMUpdateUtility and does not go into the bootloader...
Any ideas?
I am going to try MAGLDR 1.11 now and see what happens.
Click to expand...
Click to collapse
When you run the RUU does the phone reboot into the tri-color screen (bootloader) and then flash anything? Does the RUU indicate that it flashed successfully? Have you tried running the RUU with the phone already connected in the bootloader, rather than via ActiveSync in Windows Mobile?
The max that could happen is this that my android on nand would be erased, but then I could easily reflash it using magldr 1.1.3 .. correct me if im wrong
Im having the same issue.
Ran the update utility fine and now running the DAF.exe file but getting the error
An error has occurred
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (725)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (304)
Makes no difference if i run it as admin or not it does the same thing.
Please help ASAP as im just done it.
magdlr trouble.
i cant update it to 1.13 either. it says its doing it. but then starts giving errors. and once i get back into the boot menu its shows 1.12 and quits reading the sd card and/or nand memory... i basically hav to reinstall the android...
Hello!
WP7 is not booting up for me. MAGLDR shows:
1234FATAL HIT 4
Tried different WP7 roms, radios, did task29 reflashed MAGLDR.
Anyone know how to fix this?
I read somewhere else about this...
Try re-flashing a WinMo 6.5 stock ROM via freshly formatted SD card (FAT32), then re-install HSPL, Radio ROM 2.15.50.04, MAGLDR 1.13 and the WP7 ROM of your choice.
Also, make sure your SD card is good for WP7.
Esh.. today I've had a while and reflashed stock rom ect (which worked well).
Now...
When I'm trying to flash DFT_LEO70_RELEASE an error occurres:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: flash write failed.
Info: .\RSPL\RSPL.cpp (710)
Click to expand...
Click to collapse
And after flashing f.e. blackSideSeven v1.2.7004 MAGLDR shows:
1234FATAL HIT 4
Also I have problem with booting android nand roms...
What if my nand memory has been corrupted?
So i installed HSLP and radio on my HD2 and MAGLDR 1.13.
So i downloaded stock gingerbread 2.3 and when i go to USB flasher and run ''RUN.EXE'' ,
it gave me this error in DFT ANDROID FLASHER
Happen error
Read below for more information
Error Description: send partition data failed
Info: .\RSPL\RSPL.cpp (802)
Error Description:
Info: .\RSPL\RSPL.cpp (545)
I also tried doing this with the sd card out of my phone.
I also tried flashing to my stock rom and when HTC LOGO comes up with the white backround,it auto reboots.
I also tried task 29.
Any suggestions?
dazkyl said:
So i installed HSLP and radio on my HD2 and MAGLDR 1.13.
So i downloaded stock gingerbread 2.3 and when i go to USB flasher and run ''RUN.EXE'' ,
it gave me this error in DFT ANDROID FLASHER
Happen error
Read below for more information
Error Description: send partition data failed
Info: .\RSPL\RSPL.cpp (802)
Error Description:
Info: .\RSPL\RSPL.cpp (545)
I also tried doing this with the sd card out of my phone.
I also tried flashing to my stock rom and when HTC LOGO comes up with the white backround,it auto reboots.
I also tried task 29.
Any suggestions?
Click to expand...
Click to collapse
Well i had the same problem las night. The solution that worked for me was very simple.
I flashed an WM6.5 ROM and after that i`ve installed again MAGLDR 1.13 and i flashed my HTC HD2 with an android rom.
Please reply if worked for you too. Thnx
Hello,
I am running android 2.3.7 [typhone v3.6.9- magldr]. I wanted to upgrade my rom, so I got into magldr and then to recovery, but when I choose "ad recovery" I get an error massage in red "ERROR: ERROR: Cannot read ramdisk image "
plese help ...
How can I solve this problem ?
thank's
Reflash recovery and then see it it's reproduces or not.
If you have do a task29,you have to reflash MAGLDR and the recovery who is needed for this ROM.Task29 delete MAGLDR and Recovery.
Maybe you need reflash your device recovery.
You really don't have to task29 your device.
Just download HD2 Toolbox, connect your HD2 to your PC and hit update in the left corner.
Thats it
Hi All,
I have this device for a long time and I have flashed many roms...
Suddenly it's not possible to enter the "AD Recovery" in Magloader ClockworkMod Recovery.
it stuck after "1234 GO GO GO!"
I have tried the following:
1) Re-flash MAGLDR1.13.
2) Repartition with HD2Toolkit (I have European device so I repartition to 200)
Any suggestions?
Flash win mobile 6.5 and then flash magldr again
Sent from my HTC HD2 using Tapatalk 2
Hi All,
I m trying to go back from android to winmobile and my device is stuck...
In bootloader (3 colors) i have the following error: "upgrade rom code error please try again"
I have tried to flash different winmobile roms include RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2. 15.50.14_LEO_S_Ship and i have tried to flash HAED SPL 4 and i received error in device id...
In bootloader it appears correctly with SPL-2.08.HSPL 8G XE, and in the white eare it write Serial in in the begining and when I try to flash it change to USB.
The main problem is that I have tried to flash Energy.Leo.21916.Sense2.5.Jul.04 above android it stuck on 4% and I can't reflash anymore, when i try to reflash it stuck on 0% no matter what I do.
In bootloader (3 colors) i have the following error: "upgrade rom code error please try again"
Please advice...
sagytb said:
I have this device for a long time and I have flashed many roms...
Suddenly it's not possible to enter the "AD Recovery" in Magloader ClockworkMod Recovery.
it stuck after "1234 GO GO GO!"
Click to expand...
Click to collapse
Been having the exact same problem (http://forum.xda-developers.com/showthread.php?p=29868470#post29868470) still noone with any ideas how to fix this?