Hi experts,
I have a HTC HD2 (T-mobile).I am using it as unlocked with Wind Mobile, Canada.I like to use Android froyo but not sure which rom and version of froyo I should consider.After seeing so many forum I understand that not all roms are for the T-mobile HD2.Does any one has little time to suggest me?As it was an expensive cell phone for me, I want to use all of its features including camera flashing,wi-fi and ofcourse Skype over wifi,G-sensor too.please help me.
Before you can get the correct rom you need to know a few things about your HD2. I have just done this (with a lot of help of people both on and off this forum) so I will sread what knowledge I have.
1) Figure out which SPL you have (restart your phone whilst holding down the volumn down key).
2) Download the correct HSPL for your phone.. so if you have SPL 1.66 then download and install HSPL 2 (as it covers 1.66, .172 etc
3) Verify that your Radio is 2.08 or above. if it is not then upgrade it
4) download your choose Andriod rom -- I brought down Froyo 1.8 mattcleofroyo1.8
5) your SD card has to have at least 2 gig free
6) unpack your android rom and you will get an Android folder - copy that to the root of your SD Card.
To start Android
============
NOTE: the first time you do this it will takes ages so DON'T PANIC - it can take up to 15 minutes
1) make sure you have at least 50% battery power or are on main power for the first start
2) go into the android folder and run the program CLRCAD - it will see to do nothing but that is ok
3) Run the program HARET... this will load and boot Android.
That it.. it isn't as complicated as it sounds. The important bit is the prep work making sure you have the minimum Radio version etc.
Good luck
TonyOCL said:
Before you can get the correct rom you need to know a few things about your HD2. I have just done this (with a lot of help of people both on and off this forum) so I will sread what knowledge I have.
1) Figure out which SPL you have (restart your phone whilst holding down the volumn down key).
2) Download the correct HSPL for your phone.. so if you have SPL 1.66 then download and install HSPL 2 (as it covers 1.66, .172 etc
3) Verify that your Radio is 2.08 or above. if it is not then upgrade it
4) download your choose Andriod rom -- I brought down Froyo 1.8 mattcleofroyo1.8
5) your SD card has to have at least 2 gig free
6) unpack your android rom and you will get an Android folder - copy that to the root of your SD Card.
To start Android
============
NOTE: the first time you do this it will takes ages so DON'T PANIC - it can take up to 15 minutes
1) make sure you have at least 50% battery power or are on main power for the first start
2) go into the android folder and run the program CLRCAD - it will see to do nothing but that is ok
3) Run the program HARET... this will load and boot Android.
That it.. it isn't as complicated as it sounds. The important bit is the prep work making sure you have the minimum Radio version etc.
Good luck
Click to expand...
Click to collapse
hi TonyOCL,
I am just curious to to know, does every single function worked for you?
I mean all hardware functions?did you find any difference in battery life
between winmo and android?Can you still boot winmobile os?
Anyways, thanks for reply.
mlhazan said:
hi TonyOCL,
I am just curious to to know, does every single function worked for you?
I mean all hardware functions?did you find any difference in battery life
between winmo and android?Can you still boot winmobile os?
Anyways, thanks for reply.
Click to expand...
Click to collapse
Sorry I can't answer your questions as I only finished doing this last night. Until I fully sync my contacts - I can't play with android.
I also will be downgrading my radio to 2_12 to improve stability. Obviously it will take a week or so before i can comment especially on battery.
The instructions I gave will give you android but Windows Mobile will still be your initial OS. So you will boot WM then start android.
Like you .. I won't make Android my default OS until I have tested everything you mentioned.
Hope this helps.
Ok.....First I will admit I am new at all of this, second , I am a girl. Not that, that is a big deal but you get my drift. I have spent the last 24 hrs trying to find a good version of android 2.2 to install on my HTC HD2. I have tried quite a few versions, only one has installed that was the FroyoSense. However, none of my status lights worked, personal ringtones didn't work, picture preview didn't work. I create themes for the market and wanted to run android on this phone to help me out with my themes.....can anyone point me in the right direction? Thank you so much in advance.......that is if anyone is up as late as I am.... : )
Mickey
Hi Mickey,
The best builds I've used are NexusHD2 1.8 (if you want completely stock Android) and MDJ Froyo HD 4.6 (if you like the HTC Sense look). You will need to flash your HD2 using ActiveSync with a new '.50' radio. They can be found here (2.15.50.14 is the one I'm using). Without the new radio you'll be unable to boot.
I'm currently running MDJ Froyo HD 4.6 and it's quick and stable with pretty good battery life. I experience trouble with 'robot voice' when calling on NexusHD2, however everything else works just fine. Once you get a bit more confident you can have a play with custom kernels and whatever else.
To install one of these builds follow the link and download the package, then extract everything. I take the MicroSD out of my phone and use a card reader plugged into my PC to format the MicroSD FAT32. Quick format works fine for me. Then I copy the files into a folder called 'Android' (do not use all capitals) in the root of the SD card. Then boot into Windows, use file explorer to find your 'Android' folder and run CLRCAD.exe (nothing will happen - that's fine). Then run HARET.exe, click 'yes' when told about an unknown publisher, and it will proceed to boot you into Android.
First boot may take up to 10 minutes, as the device creates a virtual 'phone memory' for your apps and sets up the kernel. Once it's booted and at the lock screen, leave it for fifteen minutes. After fifteen minutes, unlock and power off your phone completely. Rinse and repeat the booting process, and your Android should be working perfectly.
I'll keep an eye on your thread in case you have other questions. Make sure you flash that radio first, or you'll be in all kinds of trouble.
Good luck!
Justin
This is exactly what ive been looking for Juzz. can you elaborate on activesync and the radio more? installation, etc? and that froyo work with gen. y? If not, whats a good dual boot?
Truaim,
ActiveSync isn't actually called ActiveSync anymore, it's Windows Mobile Device Center on Vista and Windows 7.
When you connect your HD2 running Windows to your computer with the USB cable, you are asked (on the phone) what kind of mode you want to select. ActiveSync is first, then USB Mass Storage, Internet Gateway etc. ActiveSync is the mode where you can update new firmwares, install HardSPL, and (if you use them) sync Outlook calendars, mail and contacts.
I am assuming you have HardSPL installed, which you use to flash custom Windows ROMs? It's not necessary (strictly speaking) for Android, but makes flashing radios easier. Let me know if you need me to cover that more.
Android on the HD2 only works with radios that follow the '2.xx.50.xx' format. They MUST have that .50 or you'll run into trouble. Flashing a new radio is just like flashing a new ROM. You download the installer, extract and run CustomRUU.exe, which launches the update process. Your phone needs to be in ActiveSync mode for this to work.
If you follow my previous link to the radio thread, you'll find all the .50 radios at the top. I'd go with the 2.15.50.14 radio first. Download it, connect your phone, unzip and run CustomRUU. Then follow the prompts. Your phone will do a few odd things, reboot and be running the new radio. It doesn't change Windows in any way, shape or form. It just updates your radio. You won't see any changes, except in the 'About' page where it lists the radio version.
Hope this helps!
Justin
Also, I run the 1.66.405.2 Generic WWE HTC Windows 6.5 ROM. I don't use any kind of bootloader (I'd rather be sure CLRCAD was run myself). There are a couple of stripped-down Windows ROMs floating around, but I find battery life isn't affected a whole lot by running a regular Windows ROM.
Cheers.
Just in case the radio package you get doesn't have CustomRUU...
The most recent stock ROM (3.14) is reported by many to be a very good ROM for running Android with. I use it myself and have had 0 issues. (It comes with radio 2.15.50, which is great for Android.)
It also means that, for once, my phone is in a perfectly "legit" state and I could send it off for repair without worry.
And I'm sorry, but there are no "best builds" for Android. The ones that are regularly updated are all running very well, so it depends what you want from it. I'd recommend ignoring recommendations and trying a few different ones yourself, as that's the only way you'll find what you like.
I bought my HD2 used, so I wont be sending it in. in fact, if it were possible id remove windows entirely. where can i see if i already have that radio installed?
Truaim said:
I bought my HD2 used, so I wont be sending it in. in fact, if it were possible id remove windows entirely. where can i see if i already have that radio installed?
Click to expand...
Click to collapse
Reboot your phone and look out for the info in the bottom left of the screen when you get the first white screen with HTC logo. The number next to R is the radio version you have.
My radio is currently 2.8.50.08... is this compatible with mdj sense 4.6 suggested above?
Should be fine mate. Give it a whirl.
Good luck!
my radio is 2.05.51
will this work or do i need to go back to 2.xx.50 ?
stramvaier said:
my radio is 2.05.51
will this work or do i need to go back to 2.xx.50 ?
Click to expand...
Click to collapse
Please read up about subjects before asking questions in future.
It is stated all over the forums that you need at least 2.08.50 (don't use a .51 radio).
I have an HTC HD2. I'd like to run Android so I can use the Intuit credit card processing software....
I'm looking for simple, idiot-proof, acronym-free instructions on finding and installing a current, stable, functional Android...
I'm sure the folks that hang out here all the time know what all the acronyms are, but I'm a touch baffled... I figured out "sd" means the SD card in the phone. But, "NAND", "CWM" "MAGDLR", and some of the arcane terminology is confusing, and I don't know what I NEED to know and what I can safely ignore...
So, I can guess and pick some Android installation (it appears there are dozens of notes touting competing versions) but it would be simpler if someone in here can recommend something for a computer literate user that doesn't want to be a cell phone O/S expert...
Recommendations?
instructions:http://forum.xda-developers.com/showthread.php?t=893948
nand tools:http://forum.xda-developers.com/showthread.php?t=1090783
rom(cm7):http://forum.xda-developers.com/showthread.php?t=933951
rom(miui):http://forum.xda-developers.com/showthread.php?t=1028693
rom(sense):http://forum.xda-developers.com/showthread.php?t=954369
simple flashing order:make hspl 2.08 using hspl4-task 29-flash radio 2.15.....-flash mgldr-flash proper cwr partition for selected rom-if you use eu hd2 make sd-ext partition in sd(this can be done by mgldr)-put your rom.zip in sd-in mgldr choose ad recovery-install zip from sd-choose zip from sd-after installation complete press back then reboot.ask again if you stuck
Not to sound ungrateful 'cause I'm sure there's a lot of useful information in there somewhere, but this is exactly why I'm requesting something idiot-proof...
simple flashing order:make hspl 2.08 using hspl4-task 29-flash radio 2.15.....-flash mgldr-flash proper cwr partition for selected rom-if you use eu hd2 make sd-ext partition in sd(this can be done by mgldr)-put your rom.zip in sd-in mgldr choose ad recovery-install zip from sd-choose zip from sd-after installation complete press back then reboot.ask again if you stuck
Why am I flashing anything?
What is hspl 2.09 and why would I need it?
what on EARTH does "hspl4-task 29-flash radio 2.15" even MEAN?
why do I need a "proper cwr partition"?
and what rom am I selecting?
and on and on......
OK, so I presume the above is either a test or a bit of humor at the uninformed observer's expense (that'd be me)...
So, can I have all this translated from phone geek to dumb end user now?
Again, I presume I can just put Android on the SD card without a lot of pain and anguish, so still wondering what's a good, stable, fully-functional installation that'll run the GoPayment software and let me swipe credit cards through the phone...
my question, did you read the links? i mean really really read them? not just click and say "oh ****, that's a lot of text, i need help?" trust me....read them...then read them again...then read it again. it will start to make sense. your questions--
best read for a lot of your questions (besides what was posted above):
http://forum.xda-developers.com/showthread.php?t=1021837
Why am I flashing anything?
- you said you wanted android. technically you could use an sdcard rom, but he was just trying to give you what you asked for. guess the question should be why are YOU flashing anything?
you should ask - do i want windows mobile and android, only android (get rid of windows mobile all together) or windows phone (wp7) and android. only then can we point you in the right direction.
What is hspl 2.08 and why would I need it?
- read my thread above!!!!!! cuz you can't flash android without it (this is a custom bootloader that allows your windows mobile phone to install magldr or clk which allows you to install android to nand - aka install android to your phone)
what on EARTH does "hspl4-task 29-flash radio 2.15" even MEAN?
ignore the task 29 (i have never done this).
hspl4 will install hspl2.08 to your phone. this unlocks the bootloader. layman's terms - allows you to install magldr or clk to install android (or windows phone 7)
you need a particular radio to make this all work. that radio is 2.15. a radio is what allows your phone to make calls/data/etc. don't ask why this is, this is just the way it is. the radio your phone came with is likely different.
why do I need a "proper cwr partition"?
- cuz this allows you to install android. too small a partition, android won't fit. too large a partition, wasted space. just right partition = all good. you need to READ the rom thread to know what is the right partition.
and what rom am I selecting?
- you need to READ about the flavors of roms. there are a bunch. take one and try it. if it doesn't work, find another.
Again, I presume I can just put Android on the SD card without a lot of pain and anguish,
- yes, this is true
so still wondering what's a good, stable, fully-functional installation that'll run the GoPayment software and let me swipe credit cards through the phone
- beats me. but why not just try something? sdcard roms cannot in anyway hurt your phone.
now go read. and read. and read. and then experiment. good luck.
here is the best idiot proof way to get android on your phone. it is a winmo rom that has android already built in so you wont have to figure out what is what. its so easy even a cave man can do it.
Well, as usual, the secret to getting the right answer is asking the right question. And the trick to asking the right question is knowing most of the answer....
I didn't........
What I'd LIKE to do is have some current, fully functional version of Android available so I can process credit cards through my HD2 using a swiper. Over time, I may attempt to migrate other things to Android - like contacts and such. But initially, I'm just concerned about the CC processing.
So, as I understand what I want to do, putting Android on the SD card will work, and I just need to figure out which one of the umpteen versions is a good one. I'd like a home page that looks at least somewhat like my current Windows page. I"d like the buttons to continue to work as they currently do (as much as possible)....
I went out and started looking at the various SD Android versions here and selected the nexushd2-gingerbread v2.8 one because of a reply in a previous note asking for a "good" Android......
Installed it, and it works fine, although I"m not particularly fond of the home page. Put the GoPayment application on, plugged in the swiper, and ran a charge.... Appears to work fine, so it solves my primary problem...
Now, since I've figured out I'd prefer to use an SD installation, and have one that works, is there a "better" one that I should try? One that looks and feels more like the Windows Mobile 6.5 I'm used to? Or, is there one that has a different look and feel, but some functionality that makes it superior to the others?
This ROM I'm about to recommend dates back to last November...
However, I have tried every SD ROM since that time, used them for either a few hours/days/weeks, and still always returned to this one. It is just flawless, albeit Android 2.2.
Just download it, throw the 'Android' folder into the SD Card, and run the two files (CLRCAD.exe which appears to do nothing, but does enable the sound, and then Haret.exe)
http://forum.xda-developers.com/showthread.php?t=847631&highlight=black+blue
If you decide to move off WinMob, then NANDs are good, but personally I just have a WinMob program which runs on boot and then executes those two files)
Enjoy!
dkperez said:
Now, since I've figured out I'd prefer to use an SD installation, and have one that works, is there a "better" one that I should try? One that looks and feels more like the Windows Mobile 6.5 I'm used to? Or, is there one that has a different look and feel, but some functionality that makes it superior to the others?
Click to expand...
Click to collapse
do you like sense base builds or would you prefer 1 that doesn't have sense like cm7 or a miui ROM?
AmeriCanAndroid seems to be a favorite for a lot of people and is updated rather often but i personally like RafDroid HD found here. if you want to take a look at other android builds for the htc hd2 found here on xda check out this webpage. it will also give you some info about each ROM like the base, build, when it was updated & if it has sense or not. when you find one you want just click it & it will link you back to the page found on XDA.
Am I correct that "Sense" is the user interface used on the Windows Mobile HD2? If so, yes, I like it, but probably because I"m used to it. I'd have to try some different versions with different UIs to see what's most comfortable.
I'm currently running the nexushd2-gingerbread v2.8 one I downloaded yesterday. The UI is enough different that it's taking a little getting used to.
I'll have to give the others you mentioned a try, and go look at the web page that shows the different builds. I"m amazed at how many there are.
Just for fun I downloaded the AmeriCanAndroid 08/1/11 version and put it on the SD card..... Tried to run clrcad.exe and got the "CLRCAD annot be opened" error. Tried haret and got the same error. Both say "Either it is not signed with a trusted certificate, or one of its components cannot be found..."
So, am I missing something simple or is there a problem with this build? I found a couple topics in here about problems with clrcad but they seemed to wander aimlessly without any resolution...
I've now looked through a couple DOZEN topics over the last year with complaints of exactly the problem I'm seeing with clrcad and haret... I don't see a resolution in ANY of them......
Yesterday, copied the files onto the phone for the nexus gingerbread Android, ran clrcad and haret and was up and running.......
Now, I've tried three different builds, including reinstalling the nexus one, and NONE of them will run. I get the same error for clrcad and haret every time.
Shutting down the phone didn't do anything.
I figure there's got to be a simple, obvious answer sitting here but I'm not finding it.
sense for windows mobile & sense for android are two different things. i personally dont know of any android rom or app thats availible in the market that will give you a windows mobile look or feel. i would find a rom that you want and then try & find a video on youtube that matches it so you can see what its like before you go through all the steps to flash it.
did you unzip AmeriCanAndroid or did you leave it in a zip file? i have since moved to nand builds so im going from memory which is starting to fail me in my old age but i think it needs to be unzipped using something like 7-zip. i think you just put the android folder on the root of your sd card. there is a video in the thread that shows you how to do the install. you can find that here.
so you tried to re-install something that worked for you yesterday but now you cant install it again? how long did you wait because with some builds it can take as long as 10-15 mins to install everything correctly. could you give me the steps you took step by step to try to install AmeriCanAndroid? i think thats the only way i would be able to help.
Yesterday I downloaded the Android 7z file. Unzipped it on the PC and let it create an android folder with all the files. Plugged in the phone and copied the android folder to the root of the SD card on the phone. Ran clrcad and haret on the phone and IT WORKED PERFECTLY.........
Today, just to try one of the builds recommended in here I downloaded a different android. did EXACTLY the same thing - unzipped with a 7z unzip, copied it to an android folder in the root of the phone, ran clrcad and got the error. Ran haret and got the same error........
Cleaned off the android folder on the phone, rebooted, tried a soft reset, etc.
Copied the nexus android build from the PC to the phone - EXACTLY AS I DID YESTERDAY WHEN IT WORKED. Ran clrcad and got the error......
I don't know what's going on with the phone or the Android builds or what, but there are a LOT of entries here and elsewhere on the web about people having exactly this problem. And so far I haven't seen the answer that makes this problem go away......
My recollection is that I had EXACTLY the same problem about 6 months ago. Installed an earlier version of Android and after the first time I rebooted the phone I could never get Android to run again. Just got the same clrcad and haret errors...
So, SOMEBODY, what's causing this and how do I get rid of it WITHOUT having to do some hard reset the destroys everything on the phone?
Back up any data on you sd card you need (I.e. pics, vids, music, whatever you feel important.) Download the Panasonic sd formatter and format your sd card. Copy over the android folder that is in the 7zip that you have unzipped. You should be able to boot ok from there.
Sent from my AmeriCan NANDroid HD2 r727 magldr
Formatted from the PC.
Installed the formatter on the PC. Formatted the SD card. MAKES NO DIFFERENCE. Copied the Android folder (the identical folder I copied yesterday) to the SD card, and STILL get exactly the same error from clrcad.....
Is this something that happens a lot? 'Cause so far, the two times I've had Android on this phone this has happened. And there are a LOT of topics out there with exactly this problem, and a lot of unsuccessful "do this" that don't appear to work. Does ANYBODY had a real fix for this? It worked perfectly 24 hours ago, now it doesn't. My BIG concern is that if Android is flaky and unreliable on the SD card I can't use this thing to do credit card processing if it's going to randomly fail and not be bootable.
dkperez said:
Yesterday I downloaded the Android 7z file. Unzipped it on the PC and let it create an android folder with all the files. Plugged in the phone and copied the android folder to the root of the SD card on the phone. Ran clrcad and haret on the phone and IT WORKED PERFECTLY.........
Today, just to try one of the builds recommended in here I downloaded a different android. did EXACTLY the same thing - unzipped with a 7z unzip, copied it to an android folder in the root of the phone, ran clrcad and got the error. Ran haret and got the same error........
Cleaned off the android folder on the phone, rebooted, tried a soft reset, etc.
So, SOMEBODY, what's causing this and how do I get rid of it WITHOUT having to do some hard reset the destroys everything on the phone?
Click to expand...
Click to collapse
your suppose to copy the unzipped android folder to the root of your sd card and not your phone. i think thats why your getting an error.
example: download rom and unzip using 7-zip. take the "Android" folder not AmeriCanAndroid from within that file and drag_drop or copy_paste to the root of your sd card. then using a file manager from within winmo go to the android folder & run clrcad and then haret. it should run fine. you can also use a program called Rundroid that automats some of the work. its a great app that will allow you to dual boot android but i think you might find it useful as well, you can find it here. RunDroid will allow you to run several android builds from your sd, not just 1.
fwiw, I can't (won't) say anything bad about any custom ROM offered on this board. My own favorite (to use) is a personal choice, which doesn't make it superior to any other - though it may be. It's just what I'm used to, what works for me and what I'm satisfied with.
Doesn't matter if you use a stock HD2 WinMo setup, or a custom WinMo ROM on your HD2. An Android SD build won't interfere with it. And so... (personally) I use AmericanAndroid (ACA). It IS used by a majority of folks for good reason. - BUT - I'm trying my best to be careful and clear with YOU that it may not be the best solution for you or anyone else in particular. We don't play favorites on this site for good reason! For me though... it is an extremely easy ROM to implement.
So you're having a bit of trouble with clrcad & haret... No Problemo.
Google is your friend... find and install under WinMo the 'exceller bootloader'. You'll boot WinMo... and then run Exceller. It will shut down WinMo and run clrcad & haret.
Make sure you've properly installed ACA on your SD card first. No need to partition your SD card. Make sure you're clear with the instructions on the first page and be sure to edit the startup.txt file (before installation) to change the LCD pixel density from 167 (default) to 240... unless you have eagle eyes or like tiny icons & text.
This is your simplest solution, and... get to know it a bit before you swap it for something that might (possibly) not be better. There's a reason a majority of users have chosen to use this Android build.
I'd wish you good luck, but luck has nothing to do with these things. Have fun with it! -Rob
Yes, EVERYTHING was copied to the Android folder OF THE SD CARD......
I have no problem installing yet another piece of software to (hopefully) get the necessary clrcad and haret files to run, but THIS WORKED TWO DAYS AGO. Without a bootloader or anything else. It worked.....
And yes, Google is quite effective. It showed me dozens of topics in forums where people complained of EXACTLY the problem I'm having. What it DIDN'T show me was a fix that didn't involve reformatting the SD card, REPLACING the SD card, doing a hard reset on the phone, and (this one I haven't seen before) installing a boot loader to hopefully get around the issue... BTW: all the above with the exception of the boot loader were tried by people with no success.
FWIW: I"m not criticizing any of the Android builds in here. I'm sure they're largely excellent, with slightly different flavors. And they represent a huge amount of work, of which I'm cognizant and appreciative.
I presume the problem is with Windows Mobile, NOT the Android builds, but it would be comforting to have somebody provide a solution to why it works when installed, and doesn't work after a reboot. Did all those other people that had the same problem do what I did six months ago and just give up on Android as being more work than it was worth? This isn't an isolated problem, there are dozens (and probably hundreds) of instances of people not being able to get Android to boot.
Anyhow, I"ll go find an exceller bootloader and try that. Hopefully, the thing is controllable so if things still fail I can get back to Windows...
I spoke too soon....... It's early here (having started this again at 04:00), and maybe my brain just isn't working yet, or it could VERY possibly be that I'm just too stupid to be allowed to mess with this whole thing, but I eventually found a copy of EBL2.1a._PlusUbuntu.CAB and downloaded it to the PC.
Then I went and found instructions on installing a cab file on the HD2. According to them I just COPY the cab file from the folder on the pc to My Documents on the SD card of the phone, then disconnect the phone from the PC, navigate to the folder, and click on the cab file.......
OK, sounds simple enough....... Did so.
Got a popup on the phone that said it was "Installing ..." At the bottom I got "The program is from an unknown publisher... Do you want to continue?"
So, I clicked YES...... Again, fairly idiot-proof........
And got "Installation of EBL2.1a._PlusUbuntu.CAB was unsuccessful."
Nothing else.... Just the message on a blank screen...
I"ll leave out the amount of screaming and swearing I"m doing at this point.....
Ive for an HD2 im going to give to my friends girlfriend to replace her current T-Mobile phone thats junk and has a cracked screen.
I have installed HSPL 2.08 to match the stock SPL, but now ive come to a stand still.
I only have a 4GB card right now (unless someone can tell me how to format one from a WP7 device, Windows wont recognize it).
Im getting confusing info about the US devices and radio's as well.
Isnt there a one step install for Android to SD card? Even the 'easy for noobs' directions has many confusing steps.
Unfortunately, no. The easiest way would be sd android run with haret from within windows mobile, but even that requires an updated radio.
Just put windows mobile back, update the radio (which is relatively easy if you read enough) and drop any sd build on your sd card and then click on "clrcad.exe." then "haret" from File Explorer on your phone.
That's the easiest.
Never took WinMo off but i did manage to get a 16 gig card to use. How do i tell what radio it has?
Go into settings > software information > radio.
That's it.
I recommend flashing 2.15.50 (if you don't already have one that is 2.08 or above)
2.15.50.14? Cause thats the one i've seen said 'use' and 'dont use'.
Ok, its got that radio on it. So i guess im good and can just find an image to put on the SD.
Just go into the SD android development, pick a ROM, download it and extract it into /Android/ on your sdcard.. then follow my first post.
Which Android version it is more suitable for the HTC HD2
I have an HTC HD2 running the original windows professional 6.5. and I m interested to install the Android OS in order to get
a faster an easy OS.
But after reading several posts and watching a lot of vieos on Youtube I feel lost which Android version it is more suitable to my smartphone
and if it is possible to get a little bit of more speed I woul be very happy.
As far as I understand i will require to burn or change my ROM first and then install the Android. But there are the Rafdroid version, the Ice Cream the Jelly Bean and so. Today I read a notice somewhere that a a guy have obtained 1.66 Ghz of speed at the HTC HD2 that it is amazing.
A little of speed would be great but the most important it is to have the Android because it is easy and may allow me to view videos ouside
youtube.
I will appreciate you advice and comments how to decide about the Android version.
Marvlesz said:
Just go into the SD android development, pick a ROM, download it and extract it into /Android/ on your sdcard.. then follow my first post.
Click to expand...
Click to collapse
Well, i did, i found AmeriCanAndroid. But when i launch Haret it says it cant find the zImage which is not in the NativeSD folder, but in the kernal/boot folder. Also in following the guide for this on YT, when i copy it to the SD its only 123 megs, not 232 like in the video. So im lost as to whats going on.
Also, my ex-wife had an HD2 briefly that had Android on it that you could launch from a shortcut on the home screen. Any idea how to do that?
Ok, i got this resolved. Once i realized MAGLDR wipes WinMo off i found an EXCELLENT video on YT for dual booting WP7 and Android. Thanks to the guy who made it, very thorough and had the links to the required software in the comments.