Database Users

[Q] Bricked!?!?!

I've heard about how it's pretty much impossible to brick the nook... Mine seems about as useful as a brick though. I was trying to set up a dual boot following these instructions. Basically, I had HC installed to the internal memory. backed it up, formatted system and data, then flashed update-nc-stock-1.2. CWM said that was successful. Then I rebooted with my CWM SD card out. Screen said "read forever" or whatever, then went blank. I waited for about 5 minutes, and pressed the power button. The screen went from an 'on' blank to an 'off' blank. Since then, I haven't been able to get it to turn on at all. Just an 'off' blank screen with no signs of life, even with charger cable connected. Tried it with CWM SD in and out. None of the buttons seem to do anything...
Thanks in advance!!

I'm pretty new to the Nook having just got it today, but I did some reading prior to attempting anything to see how easily I could back out if I had to.
Have you tried basically starting over (ie. Let go of the multi-boot dream for a bit and get back to basics)
You know, take a SD card, use diskimager to put the clockwork 3.0.2.8 image on it with the CM7 full ROM and boot to that, then format system, data and cache with clockwork and finally install the CM7 zip image (and gapps I guess) just to get going again.
If it all works, maybe take another run at whatever you are trying to do with the multi-boot stuff.

Thanks for the reply.
Sounds awesome; problem is I can't get the thing to do ANYTHING. boot period, into recovery or otherwise. I plug it in and it displays nothing - no 'wait 15 minutes and try again'. Just a black screen no matter what I do. I have an SD card with recovery on it, and i've tried making it do something with or without the SD card. No luck.
Good luck with your nook; I had really been enjoying mine.

So holding the power button for 10-15 seconds doesn't do anything?
Or when you plug in the power does it try to boot?
I mean in a complete worst case scenario you could grab yourself a T5 and open it up, disconnect the battery, and then reconnect it.

Then something is wrong with your Recovery SD card, as no matter what, hardware dictates that it reads the sd card first. The problem with what you did through dual boot methods is you resized partitions. So even if you do back out of all of this, you're going to be losing space unless you setup dual boot.
Recreate the CWM recovery card, either redownload the image and reburn it. Find a different one or something else, because it should load on startup.

Thanks for the help!
Reformatted SD again, then tried powering up with the power cord unplugged. Apparently it won't boot into recovery as long as the power cable is in, and whatever the boot was on EMMC was messed up. Happily running stock 1.2 now, next step, dual boot with HC!

Anyone know how I can delete this thread as it's pretty unnecessary?

[Q] Everything seems to be going wrong with my Nook Color

A couple weeks ago I bought a Nook Color on ebay. The first thing I did was turn it on and let it fully charge overnight. I noticed that it was in normal condition, but didn't bother going past the intro screen since an off the shelf Nook Color was not what I was interested in anyway.
The next day I flashed phiremod 6.2 on it with no problems (I have done this process successfully to two other Nook Color's by the way). I am able to connect to my wifi, setup my google account, and open the market. Life is good so far. Then I notice in ROM Manager that there is a phiremod 6.3 version out. I try to download phiremod 6.3 from ROM Manager for an entire day with no luck. The download just kept stalling on me. No problem I'll just download phiremod 6.3 onto my sdcard and flash it through clockwork recovery as normal (performing a full wipe first of course).
Then boot loop for no reason I can tell. Just a boot loop at "Touch the future of reading" with no way to get into recovery without restarting it with the sdcard.
So I put the sdcard back in and wipe and reflash phiremod 6.3 with the same results. Then I wipe and reflash phiremod 6.2...boot loop again. I repeat this process until my eyes start to bleed.
At this point I'm thinking, "There's no reason this should be happening. I wish I could just go back in time and start over." That's when I find this link: http://forum.xda-developers.com/showthread.php?t=914690
Ok, I'll just restore everything back to stock. No clockwork, no phiremod, just Barnes and Noble software just like the day it was born. So I go down the road of restoring the device to stock and instead of bootlooping at "Touch the future of Reading" it bootloops at the "N" screen. I'm running out of ideas so I perform the 8x method, get the OTA install, and still bootlooping at the "N" screen. Oh yeah, and "power + n" wont take it into recovery of any kind.
Now that it seems that I've failed to restore the device to stock, I try to flash phiremod 6.3 again because this is really my end goal anyway. This time it is a success. I connect to my wifi. The device says I am connected and the wifi signal is strong, but I can't establish a reliable data connection with google, or open the market, or browse the web. I turn the wifi off and on, I tell it to forget my connection and add it again, but nothing seems to work until a day later when it suddenly establishes a connection.
So everything seemed like it might be ok at this point except strange things started happening with the device. Power + n doesn't take it into recovery, and never did at any time it has been in my possession. When I try to go into recovery from ROM Manager after flashing CWR I go into a bootloop. This is even after updating Rom Manager and doing things like rebooting after flashing CWR. Wifi always says it's strong and connected but any app with internet access is often times painfully slow to the point of being unusable or at least impractical. Downloading a single app from the market is like pulling teeth, and I regularly get the "retry or cancel" popup over and over again. Sometimes when I tell it to reboot or shut off, I get the "rebooting" or "shutting off" message and it just grinds away endlessly.
The device is currently in a bootloop after just telling it to reboot (normal reboot not reboot into recovery), and I know how to pop in my sdcard with CWR and get out of it. However, my problem is that this is a gift for my sister, and I just cant seem to get this device into a normal working state that I can give to her.
I know that there are plenty of threads answering all of the little problems I have outlined here, but none have resolved them for me nor have I found a single thread that deals with a whole host of problems like this device seems to have.
Thank you for your patience in reading this.

Try restoring to stock 1.2:
http://forum.xda-developers.com/showthread.php?t=1050520
It can't hurt at this point, and it may get you fixed.

Thanks for the reply.
No dice. I tried both of those files. I made sure to format the system and data before flashing each time, and I'm still stuck at the "n" screen.

Alright so here's what I just did:
1) Format system
2) Format data
3) Flash B&N v1.1 "old" 1GB "/data", 5+GB "/media" partitioning zip from:
http://forum.xda-developers.com/showthread.php?t=1094371
4) Reboot
5) Flash Stock 1.2 update.zip from:
http://forum.xda-developers.com/showthread.php?t=1050520
6) Unmount sdcard
7) Reboot
8)Still stuck at the "n" screen.

The story so far:
I was forgetting to do the 8 reboots after repartitioning and flashing stock apparently.
I performed the 8 reboots, and my Nook did a factory reset and OTA update. Now it boots into stock v1.1.0. I see the pretty lady, there's a video, I get to accept a B&N agreement, I connect to either of my wireless connections, but after I enter my account name and password it always says "Error sorry we're having trouble setting up your Nookcolor. Please shutdown the device and try again...." It gives me a number to call so I do. After a long bewildering conversation with tech support, I'm told that my device was once registered to someone else (which I already suspected having purchased it on ebay). I'm told that in order to fix the problem they are going remove the old account from the device, and that when I restart it in an hour I will be one with the Nookcolor universe. It has been many hours, and I am still getting same error message.
Should I continue down this path with customer service (who are failing to inspire me), take it into the Barnes and Noble store this weekend (I don't have a receipt but it at least it boots into stock now), or just go ahead and load phiremod 6.3 (which is my end goal, but I want to make sure I don't take one step forward and then two steps back now that I've gotten this far)?

"Device Info" only has "back," "power off," and "reset."
I just tried holding the "power + n" for 10 seconds as demonstrated here Nook blocked after downloading latest software - Barnes & Noble Book Clubs. This guys seems very happy that this solution worked for him. I don't know why it wont work for me seeing as I have the exact same problem.

Barnes and Noble tech support came through and reset my device. It appears that I have a stock 1.1 Nook Color and all is well. I am even connected and able to browse the internet. Does this mean I am ready to start flashing new ROMs onto it, or should I do more testing while it is still stock?

So I made a nandroid backup of the stock system with no problem. Then I flashed phiremod v7 test. Everything was going well until I went to ROM manager, flashed CWR, and tried to make a backup. It went into a bootloop so I put in my sdcard with CWR. Immediately it started putting my backup on that card. I rebooted it through CWR, but it still went into a bootloop. I then did a factory reset, full wipe, and flashed phiremod 6.3... still bootlooping away. This is one of the problems I was having before I started this thread. The CWR on my sdcard is ClockworkMod Recovery v3.0.0.6.

Sorry to read that you're having so much trouble. FWIW I'm having one hell of a time using Phiremod on my NC, too. I've found solace with CM7 nightlies and the latest Dalingrin kernel.
CWR 3.0.0.6 is very outdated at this point. I use CWR 3.2.0.8 on my recovery SD. I think it was V3.0.0.6 that had problems formatting the data partition, but I could be wrong.
Hope you get it sorted out.

Thanks for the support. Do you know where I could find the latest versions of Clockwork?

There's a typo in my post above. The current version is 3.2.0.1
I read about it and got the files from androidforums.com, although I'd be surprised if they weren't on this forum, too.

I downloaded recovery-clockwork-3.2.0.1-bravo.zip, put in my sdcard, flashed the new version of CWR, and now it is endlessly scrolling through the CWR menu on its own. The log at the bottom says "ClockworkMod Recovery v3.2.0.0," then "Back menu button enabled," then "Back menu button disabled," then "Back menu button enabled," and seems to be continuing like that without end. After powering off, removing the sdcard, and holding the power + n buttons for about 8 seconds, the screen shows the cyanogenmod logo and says "booting into recovery" but does nothing. I've repeated this entire process several times while holding the power + n buttons for varying times and it still doesn't actually boot into recovery.

Wulfie6 said:
I downloaded recovery-clockwork-3.2.0.1-bravo.zip, put in my sdcard, flashed the new version of CWR
Click to expand...
Click to collapse
This is the problem. The nook color is the encore not the bravo. You have the wrong recovery image. Its a good thing its unusable...you might fubar your device if you were actually able to use that recovery.
Sent from my Phiremod Nook Color using XDA Premium App

I created a new boot disk with CWR 3.02.8 and successfully flashed Phiremod 6.3 and CM7 nightly 107. I was still essentially unable to use the internet on both of these ROMs even though my wifi connection said it was good. I did not try using my phone as a hotspot with these versions.
I'm on CM7 108 at the moment. I'm still getting sporadic internet access even though my wi-fi is pretty good (usually just shy of full bars). I connected to my phones wi-fi hotspot which produces full bars on the Nook with good internet results. This isn't practical though because I can't always have my phone creating a wi-fi hotspot. Doesn't this seem odd that my Nook is only internet reliable when it's connected to an excellent wifi connection, but functionally wont work when it's on a good wifi connection?
Also when I go into ROM Manager and try to flash the current version of CWR, it pulls up the "confirm phone model" (when it is actually connecting to the internet) but as soon I put my finger on the menu to scroll through, it selects the first one I touch. This is one of the problems I was having before on all ROMs.

So I just went into ROM Manager, flashed the latest version, then tried to make a backup through ROM Manager, and now I'm in a boot loop again except this is the kind of bootloop where I can't get it to turn off. It just sits there with the cyanogenmod logo saying "Loading..." When I hold the power down, it turns off and then comes right back on. When I hold power + n, it does the same thing but instead of saying "Loading..." it says "Booting into recovery..." I don't understand why this time it's different. If I take out the card that's in there now and put in my bootable SD card while it's in the boot loop, will it fry my cards?

Wulfie6 said:
S When I hold the power down, it turns off and then comes right back on.
Click to expand...
Click to collapse
sounds like it's plugged in

TheAmazingDave said:
sounds like it's plugged in
Click to expand...
Click to collapse
It's not plugged in.

Return to stock 1.2 - Stuck at n screen fix.
After you flash the 1.2 image with a clockwork recovery sd boot card, and are stuck at the n screen, you will need to restart and have the Nook software reset to default.
1. Hold Power+n for 8 seconds, release n, then power (it may take a couple of tries to get it right).
2. At the "Factory Reset" screen, confirm your intention to reset to defaults (press "home" n).
3. At the "Are you sure?" screen, confirm again (press "home" n).
It will then go to a "Clearing data..." screen and reboot to the stock nook software.
This procedure will reset your device to stock 1.2, just as it was when it shipped.

I second what JoeInternet says. You NEED to be on stock B&N 1.2 to be able to run the latest CM7 builds and ANY .32 Dalingrin kernels or it will not work.

Quick thought... The first thing that should have been done is an ATO 'deregister' to get that nook's ID dis-associated with the original BN account.

Nook Touch - completely bricked, no joke

Okay, I've seen a lot of "I bricked my Nook Touch" posts around, and floating everywhere but none of their solutions worked. I used the TouchNooter step by step, got the checksum right, did everything right.
Loaded the SD card, restart the nook, BAM! Got stuck on the dreaded "Rooted Forever" screen.
Here's what I've tried so far:
redoing the process
booting without sd card
booting again WITH sd card
8 failed boots
factory reset (bottom left and right and the power button)
30 seconds power button hold, 10 seconds without, 10 seconds holding it down
I think that's about it. i'm just about ready to throw this thing out, seriously. Any other ideas?
I think I'll keep on trying to do the 8 failed boots thing

wajanus said:
Okay, I've seen a lot of "I bricked my Nook Touch" posts around, and floating everywhere but none of their solutions worked. I used the TouchNooter step by step, got the checksum right, did everything right.
Loaded the SD card, restart the nook, BAM! Got stuck on the dreaded "Rooted Forever" screen.
Click to expand...
Click to collapse
As you're able to power down and reboot your Nook I wouldn't even call it bricked. Bricked is when your hardware fails or you manage to screw up your bootloader
I always get stuck on the "Rooted Forever" screen or boot animation when using either Noogie or TouchNooter image, but the process still works, so this doesn't really indicate that something went terribly wrong.
wajanus said:
Here's what I've tried so far:
redoing the process
booting without sd card
booting again WITH sd card
8 failed boots
factory reset (bottom left and right and the power button)
30 seconds power button hold, 10 seconds without, 10 seconds holding it down
I think that's about it. i'm just about ready to throw this thing out, seriously. Any other ideas?
I think I'll keep on trying to do the 8 failed boots thing
Click to expand...
Click to collapse
1,2,3: Unless a simple reboot without the SD card helped this ain't gonna do much good.
4: This usually helps if you can mange to trigger it, it will properly replace both boot and system.
5: This is completely useless. As far as I've seen all it does is clean your /data/app folder and not much more.
6: Never heard of this, can't imagine what it's supposed to do.
One thing you can try the original NookDevs rooting process , see if that kicks your boot into working order again. This is my preffered rooting method.
Your best bet is trying to trigger the 8-failed boot recovery. I've done this a few times on my N2 and it can be a little tricky.
May I ask what version you're running? 1.0.0 or 1.0.1 ?

Thanks.
As far as 6 goes, I saw it on a few forums on the 'net and it was said to break the boot cycle.
I suppose it's not "completely bricked" but I've spent so long with it, trying to get it to work that I'm really, about to ready to throw it away.
I'll try the original guide, hopefully that will trigger it.
It's a 1.0.0, I got it a week after it came out (and it's been bricked since the first TouchNooter came out).
Also, how should I try to do the 8 failed boot recovery? Half the time, it's hard to tell if it's booting, or if it's turned off o.o the only difference I saw is when the Nook is plugged in. Any ideas?

wajanus said:
Thanks.
Also, how should I try to do the 8 failed boot recovery? Half the time, it's hard to tell if it's booting, or if it's turned off o.o the only difference I saw is when the Nook is plugged in. Any ideas?
Click to expand...
Click to collapse
First you need to check whether long pressing power will reboot or just power down you Nook. From my experience a unit that "hangs" on boot will power down when the power button is pressed for at least 10 seconds, while a successfully booted unit will simply reboot.
The following is based on my experience with "hung" units:
Prereqs:
- No USB cable attached (not even charger!)
- No SD Card inserted
Steps:
1: 12 second press (to be sure) for power down
- most likely you'll see no change in the screen!
2: Wait 5 seconds for Nook to settle
3: Press power for 4 seconds to turn it back on
4: Goto step 1 as soon as you see the screen flicker!
- Do not wait for boot animation, a simple flicker is enough!
Repeat 8 times

Also, see this thread for a factory restore image

I wonder, if desperate, whether JTAG could be used.

It is REALLY too bad that some people are so impatient.
When it says "rooted forever", that does NOT mean that the process has completed. It means that the process has ONLY STARTED. Give it some time.
WAIT.
Wait 20 minutes.
It will complete.
Be patient.
If you have to, pull out the battery from the thing.
Then put in the special sdcard.
Plug the battery back in, plug the charge plug in.
Turn on.
WALK AWAY AND COME BACK TOMORROW.

Sorry, but I wouldn't call myself impatient. I pre-charged my nook to full charge before attempting rooting. I left the Nook alone without restarting it until I realized it may need charging again. It was THEN that I tried to restart it.
"WALK AWAY AND COME BACK TOMORROW" <- Yeah, I did that.
However, I do admit, I was expecting a quicker root/rom flash I'm used to my Samsung Vibrant

ros87 said:
First you need to check whether long pressing power will reboot or just power down you Nook. From my experience a unit that "hangs" on boot will power down when the power button is pressed for at least 10 seconds, while a successfully booted unit will simply reboot.
The following is based on my experience with "hung" units:
Prereqs:
- No USB cable attached (not even charger!)
- No SD Card inserted
Steps:
1: 12 second press (to be sure) for power down
- most likely you'll see no change in the screen!
2: Wait 5 seconds for Nook to settle
3: Press power for 4 seconds to turn it back on
4: Goto step 1 as soon as you see the screen flicker!
- Do not wait for boot animation, a simple flicker is enough!
Repeat 8 times
Click to expand...
Click to collapse
Will try. Currently, my nook doesn't even turn on -.-

wajanus said:
Will try. Currently, my nook doesn't even turn on -.-
Click to expand...
Click to collapse
If you can't get it to work, try nookRestore. It basically tricks the nook into thinking you've restarted eight times already.

wajanus said:
Will try. Currently, my nook doesn't even turn on -.-
Click to expand...
Click to collapse
How do you know it's not turning on?

Thread moved. Development goes in the development section, questions in the general section. Thanks.

okay, fast forward a few months forward. I did figure out that the nook DOES turn on but it's probably stuck on an infinite loop. I was successful in booting several different "recoveries". There was a tool a few months back that removed root. The "recovery" booted but didn't help.
Since then I tried the new CWR and it booted! I was so excited. I did the whole "factory reset" and deleted all of the caches. Didn't help, the screen still showed "Rooted Forever". I tried to use the "Touch Formatter", unfortunately, that didn't help either. I used the TouchNooter again but again, nothing happened.
Any suggestions? I haven't seen a "stock" image or anything like that to boot into anywhere.

If your partitions are still intact and you haven't overwritten your rom-partition by writing a touchnooter or cwm img-file directly to the nook you could try the following:
-Create a sd-card with cwm,
-download nook_1_1_update_cwm.zip from http://code.google.com/p/nst-recovery/downloads/list and copy it to the sd
-boot into cwm
-use the install zip from sd-card function to apply the update.
The nook_1_1_update_cwm.zip contains the original update to 1.1, it is just repacked to be usable with cwm. That means, if you want root, you have to root afterwards.

The nook_1_1_update.zip that you get directly from Barnes & Noble is a standard zip file with with a signature attached to the beginning. You can strip off the first 0x1A8 (424) bytes and open it with any unzipper.

Renate NST said:
The nook_1_1_update.zip that you get directly from Barnes & Noble is a standard zip file with with a signature attached to the beginning. You can strip off the first 0x1A8 (424) bytes and open it with any unzipper.
Click to expand...
Click to collapse
I actually found 7-zip can open it without having to do anything to the zip first.

you guys are AMAZING! I couldn't find the 1.1 anywhere. I'm downloading it and installing it later on today. Will update on progress

Steps work
ros87 said:
The following is based on my experience with "hung" units:
Prereqs:
- No USB cable attached (not even charger!)
- No SD Card inserted
Steps:
1: 12 second press (to be sure) for power down
- most likely you'll see no change in the screen!
2: Wait 5 seconds for Nook to settle
3: Press power for 4 seconds to turn it back on
4: Goto step 1 as soon as you see the screen flicker!
- Do not wait for boot animation, a simple flicker is enough!
Repeat 8 times
Click to expand...
Click to collapse
Steps 1-4 solved an infinite loop loading problem with Nook Simple Touch (firmware 1.1).

okay, that seems to have helped some. The Nook boots into a "Read Forever" with a "starting up" thing on the bottom (basically the way stock looks) instead of "Rooted Forever" but it seems like it's in a bootloop, stays on the same screen and never progresses. I'm going to try the n2T to trigger a factory reset. Hopefully, that'll work :/

n2t did not work. Not sure what to do next.

[Q] Nook CM-7 boot loops

I've read the other posts, and there are some similarities, but I still don't get a clear picture... So here goes...
I've had my Nook Color for about two years and created a SD card boot to CM7 that worked like a charm for these last two years, then...
the system a few days ago went into a boot mode automatically, and just looped. All I could do was turn it off by long press on the power button.
I removed the SD card and booted to the Nook operating system and all went fine.
Re-installed the SD card and started the boot process, it again went to continuous CM7 logo looping.
Tried recovery mode, which seemed to go well, although it shut itself down without completing the boot process.
I have tried every imaginable switch combination (volume, power, n), all to no avail. Depleted power, full power, power connected, etc. Nothing breaks the cycle.
Recent app installations were Netflix, a word document processor, a speaker amplification. Titanium backup was running sometime in the near past. Most apps were loaded to the SD card.
I would like to be able to save some documents on the SD card, but now what to do?
Reload a fresh copy of CM7?
Load a new triple boot of basic, CM7 and CM9?
Just jump to a altogether new CM10.1?
Any suggestions (remember the forum rules, now...).
Thanks a million.
Well, here's what I've done.
Burnt another SD card with CM10.1 - works like a charm but don't have any of my old files on the card -started all new.
Downloaded CWM on another card, booted to it, but got menu choices I wasn't sure about, so chose "SD boot". removed the CWM card, put in my old CM5.7 card, pressed the "N" (to start the reboot), and got the same old loop.
I guess I just don't know enough, and don't know where to go to get smarter.
And the rest of the story...
CM10.1 ran fine for two days, then this morning on power-on, I got a message of "Trebuchet" error - no matter what I did, the error message prevented starting any other program or a normal power off. So...on restart, got LOOPING AGAIN! CWMod doesn't help.
Back to Google and forums.

Problem solved! (But, other than getting a good installation, I don't remember exactly HOW!)

Urgent help needed I bricked the unbrickable nook color

Summary:
I bricked my sister's Nook Color. She bought it refurbished at a pawn shop for cheap and everything was working until I told my sister that I could root the nook and put an android rom on it. My biggest mistake ever.
I looked at a lot of forums relating to the problem and it seems like there isn't a fix. So basically I got to the point of having CWM working.
All was going so well and I decided to flash eyeballer's cm-9-encore-20120904-0700-unofficial.zip on it. The one on Goo.im. After looking at screenshots of CM9 I was impressed.
I did the factory reset on it and wipe the cache, I flashed the CM9 and it was installing and it seem that it was taking a long time and then the nook turned off.
The biggest mistake that I made was that I formatted the boot , I'm a noob, I figured I wasn't the only one so I came across a thread here http://forum.xda-developers.com/showthread.php?t=949699
I thought that CM9 got installed and when I went to turn it on, nothing whatsoever... It doesn't boot no more.
I tried putting the 1gb bootable CWM on a 1gb sd card with Win32 Disk Imager and the Nook didn't boot from the SD card either and I also did the same with an 8gb.
When I go connect the Nook on the computer it searches for a driver called Omap3630 but it doesn't install and it seems to disconnect itself.
I am was looking for more threads and found out that I'm in a similar situation as a user called Jiv_au here,
http://forum.xda-developers.com/showthread.php?t=1146065
3rd post. I also tried what he did with the 8 boot attempts, pressing power button for 60 seconds and pressing the power on, the N and the volumes.

Seakuza said:
Summary:
I bricked my sister's Nook Color. She bought it refurbished at a pawn shop for cheap and everything was working until I told my sister that I could root the nook and put an android rom on it. My biggest mistake ever.
I looked at a lot of forums relating to the problem and it seems like there isn't a fix. So basically I got to the point of having CWM working.
All was going so well and I decided to flash eyeballer's cm-9-encore-20120904-0700-unofficial.zip on it. The one on Goo.im. After looking at screenshots of CM9 I was impressed.
I did the factory reset on it and wipe the cache, I flashed the CM9 and it was installing and it seem that it was taking a long time and then the nook turned off.
The biggest mistake that I made was that I formatted the boot , I'm a noob, I figured I wasn't the only one so I came across a thread here http://forum.xda-developers.com/showthread.php?t=949699
I thought that CM9 got installed and when I went to turn it on, nothing whatsoever... It doesn't boot no more.
I tried putting the 1gb bootable CWM on a 1gb sd card with Win32 Disk Imager and the Nook didn't boot from the SD card either and I also did the same with an 8gb.
When I go connect the Nook on the computer it searches for a driver called Omap3630 but it doesn't install and it seems to disconnect itself.
I am was looking for more threads and found out that I'm in a similar situation as a user called Jiv_au here,
http://forum.xda-developers.com/showthread.php?t=1146065
3rd post. I also tried what he did with the 8 boot attempts, pressing power button for 60 seconds and pressing the power on, the N and the volumes.
Click to expand...
Click to collapse
The problem is that you formatted boot, and CM does not include all of the needed boot files if you formatted boot. You will need to flash the stock firmware back onto the device, and then you can proceed to flash whatever ROM you want on the device, LINK.
I am not sure what version bootable CWM you are using, but download and flash this one,LINK. Since you saw the Omap3630 driver prompt, it does mean that it still is alive and attempting to go through the booting process. As for getting it to boot from this card, you will not get any visual indication that the device is on or not, the screen will stay dark if it’s on or off. Since the device might have been on this whole time I recommend that you fully charge the device before proceeding forward. With no USB cable connected to the device, press and hold the power button for 30 seconds, then insert the SD card, then press and hold the power button for 5 seconds to turn it on. It should boot into the CWM recovery, if it does not press the power button for 30 seconds and try again. It might take a couple attempts, but you should be able to get it. Once you get the device to boot, wipe data/cache, and flash the stock image, and reboot the device. Once you have a working device, you can then boot into the CWM card, and flash the ROM that you want.

GMPOWER said:
The problem is that you formatted boot, and CM does not include all of the needed boot files if you formatted boot. You will need to flash the stock firmware back onto the device, and then you can proceed to flash whatever ROM you want on the device, LINK.
I am not sure what version bootable CWM you are using, but download and flash this one,LINK. Since you saw the Omap3630 driver prompt, it does mean that it still is alive and attempting to go through the booting process. As for getting it to boot from this card, you will not get any visual indication that the device is on or not, the screen will stay dark if it’s on or off. Since the device might have been on this whole time I recommend that you fully charge the device before proceeding forward. With no USB cable connected to the device, press and hold the power button for 30 seconds, then insert the SD card, then press and hold the power button for 5 seconds to turn it on. It should boot into the CWM recovery, if it does not press the power button for 30 seconds and try again. It might take a couple attempts, but you should be able to get it. Once you get the device to boot, wipe data/cache, and flash the stock image, and reboot the device. Once you have a working device, you can then boot into the CWM card, and flash the ROM that you want.
Click to expand...
Click to collapse
You gave me a bit of hope but its not booting. The nook is dead... thanks for the help.
edit: I heard that pressing Power + N is like forcing a shut down so I hold those for 30 seconds and then put the SD card in it No boot.
I tried it again and put the Sd card in it and then press the power button still nothing. I believe this is definitely dead. I wish she had bought it at the B&N store. I think I'm getting her a Nook tablet. I owe it to her.