23/2/11,My windows 7 phone samsung Focus, I clicked on the button for the update in Zune, it started updating, but now it stays at step 7 from 10, the backup, it is on 100 % for already more than 2 hours but it doesn't continue to the next step. and then Zune display the error.Error code is C101002E
when I rePower on My phone , the phone screen display:Use usb to connected the computer! my phone can not boot into the OS !
I search a lot of fix ideas,but all is no work !
can anyone help me? thans a lot
Try the 3 button format on page one of your user manual. Press and hold the vol down, camera, then power and hold all 3 until it says do you want to format. Follow on screen instructions. This is to be done with the phone off...
If it can't be fixed, supposedly carriers will exchange it for a new one.
Hi,
Omnia 7 had been working fine up until now, steps leading up to the event:
* Debranded registry using chevron tool to install a regedit app.
* received pre nodo update and installed
* Used vpn workaround to install nodo update
* Phone worked fine for a month then when the 'walsh tool' was released I ran that. Went through OK and phone was still useable.
* A few hours later I was browsing the market place and phone rebooted itself and was stuck at the Omnia7 logo. Started phone in USB mode and connected to Zune to restore - got to 34% and errored saying "phone not responding".
* Power cycled again into usb mode and connected to PC but now the device is not recognised at all in Windows (nothing showing in device manager)
* restore mode is disabled but I have ordered a 'jig' tool.
My concern is that if USB mode is no longer picked up in Windows, that restore mode won't be picked up either. I should have the 'jig' in the next day or so.
I had the same problem about a week after I got my Omnia 7 in October last year.
Obviously I hadn’t used any tools for debranding or anything then, It seems like a fault with the phone to begin with, not due to anything you done.
I rang Orange and they sent me a brand new phone the next day. So try ringing your provider.
I tried connecting the phone again tonight and zune picks it up, gets to 99% complete on restore then stops. Seems the USB is being detected again - I did have the battery out of it overnight.
I have the same exact problem but without any jailbreaking
please I you find any solution just tell me
beacuse I don't have warranty I bought it via Ebay
Using the "jig" tool, I was able to enter download mode and reflash the device. I now have a "Welcome to your Samsung Omnia7" screen.
So I can confirm this method works.
Hi
In the Microsoft answer forum someone wrote that the problem was form the battery. So, I will go first with this one.
Regarding the download mode I have problem as well. When I hold pressing the volume up, camera and the power button it display the USB connection logo same as the one in the update. I don't know why!!!
Abd654 said:
Hi
In the Microsoft answer forum someone wrote that the problem was form the battery. So, I will go first with this one.
Regarding the download mode I have problem as well. When I hold pressing the volume up, camera and the power button it display the USB connection logo same as the one in the update. I don't know why!!!
Click to expand...
Click to collapse
That is because your bootloader does not support the Download Mode and enters the Zune Recovery Mode instead.
Hi! try with this
http://windowsteamblog.com/windows_...spx?utm_source=twitterfeed&utm_medium=twitter
Did you try Hard reset?
1. Press and hold down the Power button + Volume down button + Camera button all at the same time until the device vibrates, then let go of the Power button while continuing to hold down the Volume down button and the Camera button.
2. Shortly you should see the message displaying "Are you sure you want to format?", you can now release the Volume down button + Camera button.
I just formated and same problem appear again and again
I don't what to do
please help
in addition to that I don't have the download mode
You will have to get the jig tool to enter download mode to reflash, or send away for repair.
My phone is still playing up, random crashes then stuck at Omia logo. To get it started again I have to reinsert the battery and even then sometimes it gets stuck at the Windows Phone logo. I will try one more flash and if I still have problems I will be raising a warranty claim.
This happened to my phone this morning. Tried to open Beezz, but it wouldn't start (went right back to home screen).
I obviously tried a reboot, but it got stuck at the Samsung Omnia 7 -screen.
So far I have:
(no difference between the steps)
Installed the samsung update patch\fix
Hard reset
Reflash via download mode to KB2
Hard reset
Reflash via download mode to JK1
No success so far. At the moment I'm letting it stay turned on, and every minute or so it flashes black, but returns to the logo screen.
Any help would be appreciated :d
Mine seems to work for a day or so after a reflash, then starts playing up again. Sometimes stuck at logo until I take the battery out and then put back in. I had a problem opening the messaging app, would get the tile animation then back to homescreen. I have arranged to have my Omnia sent back under warranty so will see what they find.
After a power surge, my Omnia hanged then when I rebooted, its now stuck at that Logo Screen. Did everything possible (hard reset, flash rom, go into recovery mode which gets stuck after zune reboots the phone....)
Used the windows support tool and I get this message: The phone is not in the 'Connect to PC' state. Please, make sure that you follow the instructions and your phone shows the 'Connect To PC' image
Any help would be greatly appreciated
Sounds like you have tried everything I would have already. I would send it for repair / warranty.
Turns out my phone WAS faulty and it has been replaced - should receive replacememnt today (Has taken over a month)
Hello. I was using windows 10 on my phone since it was released as insider preview. Today I decided to go back to 8.1 via the microsoft official tool and then update again to 10, because of the new updates that I wasn't able to get by the normal way. I have done this before, totally works. I connected the phone into the PC via the USB and the software started to download the package, then started installing. In the middle of the installation, the connection between the PC and the phone broke.(Later on I discovered that the USB didn't work properly....) and yeah, after that the only thing that was on the phone was a RED screen(I see this for the first time and yet I have done this before) with Nokia text on it and a progress bar. I tried to turn off the phone, but it didn't work. Couple of minutes ago the phone turned down itself and that was it. Since then, I can't turn it on. I tried holding the volume down button + power button - nothing, I tried with holding the volume down button + power button + camera button - still nothing. When I try to connect it to my PC(with working USB lol) it only says that the device is not recognized....
So, is there any way I can fix this without returning it to the store? I still can't figure out why the screen was RED and why an installation failure didn't just sent me back to the version I was on, instead of doing this... Any suggestions?
my Dell venue pro 10 5130 freeze after reset from windows recovery menu. I bought it with windows 10 installed. I did a reset from recovery menu in windows 10, the process complete and when the system turn back on, the screen says 'lets get aways with few things, English and Chinese, and ok. button at bottom. The screen freeze, not able to click on ok button. The only way to turn it off is to hold the power button until power off.
how to fix this? is there a way to get into safe mode or windows recovery mode?
citrix80 said:
my Dell venue pro 10 5130 freeze after reset from windows recovery menu. I bought it with windows 10 installed. I did a reset from recovery menu in windows 10, the process complete and when the system turn back on, the screen says 'lets get aways with few things, English and Chinese, and ok. button at bottom. The screen freeze, not able to click on ok button. The only way to turn it off is to hold the power button until power off.
how to fix this? is there a way to get into safe mode or windows recovery mode?
Click to expand...
Click to collapse
What was the reason to cause you to do a reset?
I found out maps and weather app is opening correctly. When I click on maps, it open for 2 seconds it gone, same for weather.
Try doing a hard reset. If you don't know what that is Google Dell Venue hard reset. That doesn't work I would call Dell tech support. There might be something physically wrong with your tablet
I also posted a thread on Android Central.. Sorry I can't post links
Hi guys,
So last night when I was working on a website design, I decided to test it on a tablet too. So I asked my dad if I can take his tablet and he told me that I can and once I'm done to restore it because it's very slow. I decided to restore it before using it so I don't lose time while long loading happen.
Initial status:
- rooted
- Android 4.2 or 4.4 (he doesn't remember)(I don't remember since I used Nexus Toolkit with auto detection)
- debugger mod activated
- about 50% battery
So yeah, I plugged it to my computer. I chose Auto Detect Device from nexus toolkit. I selected "Device is on/Normal" from Flash Stock + Unroot. The Nexus 7 was unlocked.
The process started.. the Nexus 7 was on my desk and I was browsing the web when I realized that it was stuck on the Bootloader screen for some long minutes.. I stopped what I was doing and looked at it for 2-3mins and nothing changed. Then I took a look at the logs and I saw some errors that I don't remember.. I tried to use the volume buttons to switch the Bootloader options and nothing worked.. Then I decided to unplug the tabled and press Power Button and Volume Down. It stopped and never booted again.
Current status:
- can't boot
- can't reach Bootloader
- when I plug it to Windows, I hear the sound that Windows detected some USB but nothing popup
- when I press the Power Button and both Volume and the tabled it's plugged, I head some sounds like USB disconnect/connect
- no little flashing light at the bottom
- black screen
I tried all Power and Volume buttons combinations, plugged and unplugged.. nothing worked..
It's possible that my Bootloader was deleted? Anything I could try?