[Q] Help needed updating 32B radio&spl - myTouch 3G, Magic General

Hey guys,
Firstly...
PVT 32B
HBOOT-1.33.0013
CPLD-10
Radio-2.22.23.02
I'm pretty new to this game but I just installed Rushness' Frosense 0.9 on my Magic and it has been a MASSIVE improvement over CM 6.1 which came pre-installed on my phone that I ebay'd from Hong Kong. 6.1 was so slow it was unuseable.
Anyway, I would like to update my Radio/SPL to the latest version. I've done a lot of searching but have run into a few problems, mostly understanding lingo.
I have Radio: 2.22.27.08 & SPL: 1.33.0013d downloaded (I assume these are the ones I want) and I have backed up my SD card to PC. I figured the process would be the same as flashing the Frosense ROM, enter clockwork mod, hit clockwork recovery, hit "flash alternative recovery", power off, home + power, nand backup, wipe, flash radio, flash SPL, flash Frosense again. However after I "flash alternative recovery" and power off, pressing Home + Power just takes me to the MyTouch screen where it freezes. If I pull battery and power on as usual phone works ok. I decided to try and partition my SD through CWM (wasn't sure if this was necessary) but I'm not sure if the partition worked, phone started to reboot then froze on MyTouch screen again.
I'm assuming I'm doing something incorrectly. Sorry if I seem as "fresh" as I am, but I'm keen to learn and would be appreciative of some easy to understand steps if someone wouldn't mind.
Thanks,

See my guide found in my signature.
Just skip the rooting part if you already rooted.
Flash the recovery and continue with the eng spl.
Once you have the eng spl, you should do the following:
1)Download fastboot commander from my signature and reboot into fastboot
2)Flash the new radio
4)If it goes well, flash the new spl
5)If it goes well, restart into recovery and flash your rom. Remember it must have a compatible kernel.
If any step fails, STOP and post here.
For ref, see this thread: http://forum.xda-developers.com/showthread.php?t=831139

Here is some insight from my recent experience. I am new at this.
Started with:
Sapphire Pvt32 Dev s-on g
Hboot-1.33.3004 (sapp30000)
CPLD-10
Radio-2.22.19.26I
Version 1.5
Stepped to:
Hboot-1.33.3005 Eng
Then installed Amon Ra Recovery
Then BIG Step to:
Sapphire Pvt32 Dev s-on g
Hboot-1.33.3013d
CPLD-10
Radio-2.22.27.08
Version 2.3.5
Keys to success:
1. Get used to searching for what you need then READ as much as you can on Recovery, Radio and SPL(hboot) prior to starting any of the changes.
Especially helpful:
(Newbie resources: http://forum.xda-developers.com/showthread.php?t=794445)
http://forum.xda-developers.com/wiki/HTC_Sapphire_Hacking
(Magic SPL) http://forum.xda-developers.com/showthread.php?t=529019
(2708 Radio) http://forum.xda-developers.com/showthread.php?t=831139
2. When comfortable with how to set up Android SDK, root, installing custom recovery, fastboot and adb, you are ready to start:
3. Find an Eng S-off SPL(I used 1.33.2005) so you can fastboot flash:
fastboot flash boot [c:/boot.img]
(Magic SPL) http://forum.xda-developers.com/showthread.php?t=529019
4. Then flash amon ra recovery once then test (press/hold home + power....)
Search in XDA for this thread. fastboot flash recovery [c:/recovery.img]
5. fastboot flash new radio! (I tried using Amon Ra recovery radio.zip to install new radio but it stuck on unbox screen) After 40 min. I freaked out, pulled battery and luckily no damage/brick.
6. adb push your ROM of choice to /sdcard/
I just followed these steps by jeff72k. Note that these instructions are on the G1 forum but G1 is same as HTC Magic/Sapphire 32B. This worked very well especially for step-by-step through the partition setup for Ginger Yoshi which is working GREAT!
http://forum.xda-developers.com/showthread.php?t=1178665

Related

[FIXED!] HTC Magic need help! phone bricked?

Hey guys
I'm so desperate and you are my last hope. I was looking for hours in several forums but didn't find any solution.
What I did:
I updated the phone to 6.35 Radio and 1.76.2007 SPL and installed a Eclair ROM. Everything went well until I installed ROM Manager app. Then I installed Cyanogen mod through ROM Manager and since then nothing works!
What's the problem:
When I switch phone on it sticks on the HTC boot screen and nothing happens.
I can go to fastboot mode but ADB doesn't recognize my phone.
I also can go to recovery mode and ADB sees the device but I cannot install any image and I cannot choose any item from the menu.
What I tried:
connect with fastboot usb: phone isn't recognized
flash via fastboot in recovery mode: <waiting for device> no response.
Install a sappimg.nbh from sdcard: Fail! main version is older.
My version:
SAPPHIRE PVT 32A SHIP S-ON G (why G??? isn't that the 32B version?)
HBOOT-1.33.0013 (SAPP10000)
RADIO-6.35.10.18
Thank you very much for your help!
LOL, I almost started cracking up. "Help me, you are my only hope" (Star Wars)
Anyhow.
Start over. Download the stock Rom, radio and spl for your MT3G. I ran into something similar with mine. I had to erase system from the CLI (command line) fastboot and wipe the phone. Then used the stock sappimg.img to get mine functioning again.
This will "Unroot" your phone
I had to plug the phone in via usb. Go to terminal or dos, and fastboot.
fastboot erase system -w
fastboot erase boot
fastboot flash boot boot.img
from there I turned the phone off, and then I copied sappimg.img to the memcard, and then booted using the vol down + power and let it install the factory rom, radio, spl and recovery.
Or you also stated that you have yours rooted. You're going to have to download the original radio, and rename it to radio.img and then flash it over using fastboot. (fastboot flash radio radio.img). This would get you to the original radio. Then I would revert back to the original ROM w/root ROM.
This worked for me. Im hoping that someone else will chime in and say if this is the correct method to use. Im not an expert. I did this at my own risk.
Someone else want to chime in?
Thanks for your help!
I wasn't conscious that I cited a Star Wars quotation :-D
First I tried to follow your steps but without succes. When I run "fastboot erase system -w" it says: remote not allow. It seems my phone isn't rooted anymore.
Also the command "fastboot flash radio radio.img" doesn't work.
Where can I get the stock ROM? Is there a possibility to extract these files from the RUU_Sapphire_HTC_Europe_3.05.401.3_release_signed_NoDriver.exe tool?
Nevertheless I keep going on although I'm a little bit tired of this issue. However, it's my mistake.
The reason why I wanted to flash my device was because I was sick of this old, boring and lame Android 1.5. Why isn't HTC getting ahead and supplies us more up to date software? An ambitious single programmer is able to provide Android 2.1 but HTC with its high-paid engineer team isn't. That's weird!
It looks like you have to put on one of the engineering SPL's first in-order to wipe the device. By the way, mine is a 32A board, and has "G" also. Weird I know.
I believe the RUU ROMS are stock. So flashing these to the phone should unroot your phone. There is a list of all the RUU ROMS and guides here:
http://forum.xda-developers.com/showthread.php?t=659403
or
http://forum.xda-developers.com/showthread.php?t=682243
These are great sources of information. I'm not an absolute expert, more of a novice. I'm new to the AC but, reading guides and such, you should get your answer and you can try a few things (within reason).
BTW, when you said that fastboot flash radio radio.img doesn't work, have you downloaded the stock radio and spl and copied them to the AndroidSDK\Tools folder? That's probably the reason it isn't working. You have to have the SDK downloaded and installed. (Read The Guides provided to help you) "Use the Force!" HAHA!
So I tried many different ways to save my htc. But by now no success!
As I described I can go into fastboot but I cannot run any commands (remote not allow). I haven't root anymore!
When I go to recovery mode it sticks. I cannot choose any item from the menu.
The only way to get the phone working is via the sdcard. It's possible to install a sappimg.zip but it says: "Fail! Main version is older!" So i have no chance to downgrade. I need a sappimg that has a higher version than my current one.
Also rooting seems not to be possible due to I have to access recovery mode (which isn't working).
Finally, the only way I see at the moment is trying some stuff that works only via the sdcard.
Thank you guys
If you are getting that sort of error that indicates that you have not created a correct goldcard. You need to have that in order to flash these devices.
Go to theunlockr.com and read that tutorial about how to create one. Or click here:
http://theunlockr.com/2010/03/10/how-to-create-a-goldcard/
Are you really sure that`s because of a wrong goldcard? I´ve tried 2 different sdcards several times but every time with the same error (Main version is odler).
No further ideas?
I can't do anything. recovery mode always crashes, no root access, goldcard doesn't work.
Finally I'm back on Android!
I could solve my problem. I found a sappimg.zip (http://rapidshare.com/files/266290371/sappimg.zip) that turned my phone to:
SAPPHIRE PVT 32A SHIP S-ON H
HBOOT-1.33.0009 (SAPP10000)
RADIO-6.35.10.18
After that, I was able to flash trough the _HTC Magic_RUU_Sapphire_HTC_Europe_2.20.401.2_HTC_CH_release_signed_NoDriver.exe.
Now I'm running on a stock ROM
madboy87 said:
Finally I'm back on Android!
I could solve my problem. I found a sappimg.zip (http://rapidshare.com/files/266290371/sappimg.zip) that turned my phone to:
SAPPHIRE PVT 32A SHIP S-ON H
HBOOT-1.33.0009 (SAPP10000)
RADIO-6.35.10.18
After that, I was able to flash trough the _HTC Magic_RUU_Sapphire_HTC_Europe_2.20.401.2_HTC_CH_release_signed_NoDriver.exe.
Now I'm running on a stock ROM
Click to expand...
Click to collapse
Good to hear.
I'll take the liberty of modifying the title of your original post and close this if you will no longer be needing any assistance. Should you or anyone else decide to need it re-opened, just send me a pm. Thanks!

can no longer boot into recovery

I have a rooted unlocked Magic 32b and have flashed many roms on it but it has suudenly stopped booting into recovery.
If i hold power and home it now just hangs on vodafone splash screen.
any ideas?
if you have an engineering SPL installed on the phone, you can use fastboot from the SDK to flash a new recovery image (assuming you can still get into fastboot mode on the phone)
Or you can go to Android Market and download ROM Manager & flash recovery through that application (both ClockWorkMod & Amon_RA supported). If the first flash fails don't worry just reflash the same recovery (2nd flash works every time)
Thanks for the help, I reflashed AMon-Ra recovery via fastboot and all is well.
I'm having exactly the same problem.
Think I flashed the 32a instead of 32b onto the magic uk vodafone device:
sapphire pvt 32A eng s-off h
hboot-1.76.2007 (sapp10000)
cpld-10
radio-6.35.10.18
aug 21 2009,18:19:15
Could you link to the recovery you managed to flash your phone using please? I've tried loads of versions via adb/flashboot and none work sadly.
Hoping I don't have to buy another phone
I have similar issue to original poster, I've flashed many roms over the last year and all have been fine until now
VOLDN+POWER, HOME+POWER, BACK+POWER are all no go.. all stuck on bootloader splash. Can someone confirm I've finally bricked my 32B?
Last SPL i put on was 1.76.2007 i think (cant confirm no fastboot..) radio was 2.22.19.26I

[Q] Cannot turn security off (S-OFF) on rooted Rogers 32A Magic

I've rooted my Magic, got Cyanogenmod running nicely, etc. I was then trying to flash a new splash screen, and noticed that my security in fastboot shows as begin on (S-ON). Sure enough it wouldn't let me flash the splash screen, it said the signature was not valid.
So, I tried flashing every single engineering SPL possible, and it never changes to off.
Here is my info from the fastboot/hboot screen.
SAPPHIRE PVT 32A ENG S-ON H
HBOOT 1.33.2010 (SAPP5000)
CPLD-12
RADIO-3.22.20.17
June 2 2009, 17:27:03
Thanks!
Find zipped hboot, put it in your sd card and flash it trough recovery...
pera987 said:
Find zipped hboot, put it in your sd card and flash it trough recovery...
Click to expand...
Click to collapse
That's what I've done. I've flashed every single engineering hboot file I can find and each one still shows S-ON during fastboot/hboot, and I"m unable to flash through fastboot.
Follow these steps (you should find it in this Mytouch Room)
1. Create your goldcard.
2. Comeback to 1.5 version by flashing rom 1.5 from goldcard.
3. Install Recovery Flasher (RF).
4. Run RF, chose Flash Cyanogen 1.4 img
5. Copy new E-SPL to root of Sdcard, Boot to Recovery mode, flash this file SPL
6. You can flash new recovery img (like 1.7.0G) by fastboot mode through your PC.
Check your new SPL now and S-ON becomes S-OFF.
I've successed on Magic 32B with perfect SPL 1.33.0006 and S-ON.
vinamilk said:
Follow these steps (you should find it in this Mytouch Room)
1. Create your goldcard.
2. Comeback to 1.5 version by flashing rom 1.5 from goldcard.
3. Install Recovery Flasher (RF).
4. Run RF, chose Flash Cyanogen 1.4 img
5. Copy new E-SPL to root of Sdcard, Boot to Recovery mode, flash this file SPL
6. You can flash new recovery img (like 1.7.0G) by fastboot mode through your PC.
Check your new SPL now and S-ON becomes S-OFF.
I've successed on Magic 32B with perfect SPL 1.33.0006 and S-ON.
Click to expand...
Click to collapse
Thanks. I'll give this a shot when I get home this afternoon.
PaulieORF said:
That's what I've done. I've flashed every single engineering hboot file I can find and each one still shows S-ON during fastboot/hboot, and I"m unable to flash through fastboot.
Click to expand...
Click to collapse
If this currently a 1.33.20** spl with s=off and a custom recovery can you please do the following
Run 'adb shell dump_image misc /tmp/misc_dat.img'
Then
'adb pull /tmp/misc_dat.img misc_dat.img'
Then send me the resulting image somehow (pm me a rapid share link or ask for my email.. there ought not be any identifiably info in misc but just in case)
This may or may not clear up why there is an issue.. and let a better process to fix it be created.. untill then try unrooting (or installing a stock spl) and re-rooting as was mentioned, just onto forget radio versions may change in the process requiring caution not to skip ahead of yourself and brick.
UPDATE:
So I got the file, misc was nearly all blank without the usual data (boot mode, CID and some other data) this is easily fixed by re-flashing misc from recovery.. I think this can even be made into an update.zip.. (since all magic/dream misc partitions are essentially the same besides the CID, and the CID is still being passed to the recoveries command line when stuck in this state.

[Q] Help. I have problem with 32b. Stuck on image.

Hello.
I have a Htc Vodafone Magic, de version.
A few days ago i rooted and install cyanogen 5.0.7 and the i've upgraded to 5.0.8.
I used titanium backup, made a backup, and then i need it to restore. After that i couldn't use the phone.
Then i inserted the goldcard made it earlyer, where i had the rom, and update it.
It was a rom 5.0.7 with no app and no android market, and no root.
Now started in fast boot (vol down + power) and i have :
sapphire pvt 32b eng s-off H
Hboot-1.33.2010 (SAPP10000)
cpld-10
radio3.22.20.17
jun 2 2009, 17:27:03.
When i try to instal a rom it said that he cannot find any rom.
I used the link [How-To] Root and un-root the T-Mobile myTouch 3G
to revert to 32b since i so that i have 32b eng s-off H and i thought that is the problem.
i used this commands
fastboot flash radio radio.img
fastboot erase system -w
fastboot erase boot
fastboot erase recovery
It did not work.
No the phone starts and locks on the image with HTC MAGIC.
Thank you for your help.
fastboot flash recovery recovery-RAv1.2.0G.img
No the phone starts and locks on the image with HTC MAGIC.
when the phone stats with usb in it appears fastboot on a red background.
And i cannot use adb commands.
It is bricked?
the fastboot option works. i send recovery-RA-sapphire-v1.7.0G thru fastboot and the message was okay.
I think you can download radio 2.22.23.02 as zip file, put it on root of memory card, boot to recovery mode, apply this zip. Everything will be OK.
I flashed it 2 days ago for udating for my Magic radio version from 2.22.19.26I.
You can find the file on this room or I will attach it later.
thank.
i used Revert to 32B Radio and ROM procedure and made it.

Myouch 3G 1.2 Cant flash anything

So i had to fix the SPL on the mytouch because i kept getting the Fastboot Remote Not allow, So i did the SPL Fix and rebooted and i had a black HTC Magic screen, Got some progress then it said to throw a rom on there but i couldnt get to recovery, i try to flash a recovery and i get remote signature verify fail. So i tried flashing the SAPPIMG again and it is stuck on unzipping, Rebooted again and tried to flashboot boot recovery.img it transfers the recovery and reboots and stuck ad the black htc magic screen again.
Well i made some progress i can flash recovery and stuff now but it wont boot to recovery, i got the recovery to flash successfull but for some reason when i hold home and power it sits at the magic screen
As of right now i have
SApphire PVT 32a eng s-off h
hboot-1.76.2007
cpld-13
radio-6.35.10.18
Well i think ive done everything to this phone............ would be nice to figure somthing out. Been working on it since about 10AM this morning and i got nothing, does anyone have a fix?!
Any help would be appreciated!! Thanks Guys!!
Its bricked. The mytouch 1.2 can only run 1.33.0013 spl and the 2..x radio. Its a hybrid hardware. 32a board with a 32b radio.
NetrixTardis said:
Its bricked. The mytouch 1.2 can only run 1.33.0013 spl and the 2..x radio. Its a hybrid hardware. 32a board with a 32b radio.
Click to expand...
Click to collapse
I can flash a new radio on it and a new SPL on it, it takes that when i flash it
To root the phone you need to use the ENG spl 2010 flash your custom recovery, then stock radio and spl. After that, flash ROMs thru recovery. You can not use any other radio/spl at this time.
NetrixTardis said:
To root the phone you need to use the ENG spl 2010 flash your custom recovery, then stock radio and spl. After that, flash ROMs thru recovery. You can not use any other radio/spl at this time.
Click to expand...
Click to collapse
I think i bricked it now..... it stuck on a 0009 SPL and i cannot do a sappimg it wont unzip and i cannot flash a different spl it does the signature verify fail
Does your phone have the 3.5mm jack? Are you sure you've got a 1.2?
Well, If your phone still turns on and your have a working goldcard, try the ENG 2010 SPL from the Magic SPL thread. once you are back down to 1.33.2010 SPL and 3.22.x radio, fastboot your custom recovery, flash stock mytouch 1.2 radio then spl.
At that point, you won't have any OS tho. so, go into recovery, wipe all (but NOT your SD goldcard). Then flash custom ROM+gapps (if needed)
What is your fastboot info RIGHT NOW....
Remember that if you have a MyTouch 1.2 (with 3.5mm headphone jack) you MUST have the following AFTER you flash your custom recovery.
Radio: 2.22.23.02
SPL: 1.33.0013
So use the engineering SPL (2010) and 'fastboot flash recovery recovery.img' with a Amon_Ra 1.7.0G or Clockwork Recovery for MyTouch devices (NOT MAGIC).
Afterwards reboot to your recovery by holding HOME while booting. If you can boot into recovery then flash your stock spl (1.33.0013) back. Then flash your rom.
supercobaltss said:
So i had to fix the SPL on the mytouch because i kept getting the Fastboot Remote Not allow, So i did the SPL Fix and rebooted and i had a black HTC Magic screen, Got some progress then it said to throw a rom on there but i couldnt get to recovery, i try to flash a recovery and i get remote signature verify fail. So i tried flashing the SAPPIMG again and it is stuck on unzipping, Rebooted again and tried to flashboot boot recovery.img it transfers the recovery and reboots and stuck ad the black htc magic screen again.
Well i made some progress i can flash recovery and stuff now but it wont boot to recovery, i got the recovery to flash successfull but for some reason when i hold home and power it sits at the magic screen
As of right now i have
SApphire PVT 32a eng s-off h
hboot-1.76.2007
cpld-13
radio-6.35.10.18
Well i think ive done everything to this phone............ would be nice to figure somthing out. Been working on it since about 10AM this morning and i got nothing, does anyone have a fix?!
Any help would be appreciated!! Thanks Guys!!
Click to expand...
Click to collapse
I had the same issue the other day while experimenting on my mt3g 1.2. What worked for me was using adb to push the stock mt3g hboot and radio and then rerooting my phone. You can download the files you need from the unlockr.com web page and skim his how-to for android in the unrooting section. Hope this helps.
does it still boot into fastboot, hboot, or recovery?
supercobaltss said:
I think i bricked it now..... it stuck on a 0009 SPL and i cannot do a sappimg it wont unzip and i cannot flash a different spl it does the signature verify fail
Click to expand...
Click to collapse
if it boots into fastboot, hboot, or recovery you are not sunk yet. you will need the "official" sappimg.zip or .nbh on your gold card, but it should go through the steps and re-image it.. this will get your phone back to stock.
are you using a Tmobile MyTouch 1.2? or are you using a Rogers Magic?
the files will be different as the hardware requires differnent drivers.
there are many links on this site, or theunlockr.com that will get you the correct files you will need. make sure you check the md5 sums on anything you download to make sure its not corrupted before trying to flash it.
hope this helps.

Categories

Resources