Database Users

frozen tablet after partial update, copied fron the wrong forum

original Post
Going Bald here. I have searched this forum and the more I am reading the more confused I am becoming.
After a partial update my Acer Iconia A 500 froze. I tried rebooting and it took me to the start up screen where the lock is and nothing. Frozen solid.
I got acer support and they told me to Hold the vol button while turning the power on for 3 seconds the turning the screen lock on off on off. I get a green robot with a yellow exclamation mark. I am guessing this is called bricked!
I purchased the Tablet at Best Buy in the USA and brought it home to Australia.
The Acer support wants me to send it in for repair and also says...quote "However, considering that your device has been flashed to the US firmware, there may be an issue with resetting the unit to Australian standards."
I have read about OTA and kernels Roms.... YIKES. Most say download the OTA for your tablet ( how do I know what one if I cant get into it)
Can some Guru here please explain in clear English what I should do. Where I should go. You guessed it total Newbie here. HELP
Thank you in advance
Answer from FLOATING FATMAN.....thank you
There are several things you can try.
First, on the right hand side of the device there's a little hole. This is a reset hole (but doesn't wipe RAM). Try pressing this. You might have to reset a couple of times. If that doesn't help, read further.
Next, the step they describe is to force a wipe of the device. But it depends which volume button you pressed. With the device in landscape mode, it needs to be the side of the rocker furthest from the power button. Hold both down, then when you get the text, release the (I think) power button only, and toggle the orientation lock a few times.
If THAT doesn't work, contact the user sc2k on these boards via PM and he may be able to help you recover your tablet.
Question. When you tried to update your ROM, was it with an official OTA? And did you use Clockworkmod? If you used CWM, did you use the custom one in the A500 section, or the one from the market. The one on the market WILL BRICK YOUR TABLET.
My answer
Tried the reset, tried the power button. To answer the question.. The update flashed up on the screen so I thought it was a normal update. ummm Clockworkmod???? I havent updated from the market. Didnt know you could.
I am totally lost and ignorant here. SC2K will you please help me.
Thank you

ClockworkMod is a recovery menu for rooted roms.If you have'nt rooted then no need to worry about that.Ok power off,hold the volume button down from the left side,turn on your tab while holding down the volume button until you see small text pop up in the top,left corner,press the volume button again to wipe the tab completely(total reset)the pin hole on the side of your tab does the same thing.If this doesnt work,turn off the tab and plug in the usb cable to the tab and connect to your computer,your computer will try to install the driver,you might have to search for the driver on the acer site,then after it installs,you should be able to access your sdcard.You will need to search for the update or fix,not sure what tool is used for acer.

Is there anymore help out there. I dont want to download anything until I know for sure exactly what Im doing. I hate this tablet!

sassybees said:
Is there anymore help out there. I dont want to download anything until I know for sure exactly what Im doing. I hate this tablet!
Click to expand...
Click to collapse
OK, let's take this a step at a time. At the very least, we should be able to get the tab functioning again for you.
First, you're going to need a new ROM. I don't know what region Australia is, but at this point I don't think is really very important, so for now I suggest you flash am international ROM. We can worry about the region later.]
Download this file: http://vache-android.com/v1/download.php?fileID=75
This file is NOT encrypted in any way. Extract the update.zip from this file.
Now, you need a microSD card. Sometimes these cars have trouble reading (this often causes the yellow exclamation point), so you might want to format it first (format it to FAT filesystem, not NTFS). If possible, do this in an Android phone.
Copy the update.zip to the card. Must be in the root of the card.
Put the card into the A500, then boot into recovery (Hold down power and volume down, the one closes to the power button in landscape). Keep BOTH of these held down until you see a few lines of text in the top left of the screen. Once that is visible, release the buttons and the device should update.
At this point you should have a working tablet with an international ROM.

i had the same problem with sassybees.
i've tried to download the file but the page is locked...

I have download the update.zip full package but i just don't know which version. I'm a malaysian. Is it need a specific version for countries? I had tried the 4.010.22_COM_GEN1 and the 4.010.40_COM_GEN1 but it seems not working cause when updating, the loading bar stops about 80% and the gear animation stop rotating. The tablet restart and freeze at the android text loading screen again.
I'm so confuse about cwm or other things.. i just need a simple steps to get back to original android system.
How can i solve this problem. My acer tab is useless if it just showing android loading text forever...

The steps really don't get any simpler than the ones I've already given...
Have you tried different SD cards? I've already mentioned these are a common point of update failure.

yeah... i had tried 2 sd card... formatted wit fat system..
just wondering which version i must use? i'm searching in the dev section and found so many version.
the link u had given is somehow locked.. how can i access it?

thelock_bp said:
yeah... i had tried 2 sd card... formatted wit fat system..
just wondering which version i must use? i'm searching in the dev section and found so many version.
the link u had given is somehow locked.. how can i access it?
Click to expand...
Click to collapse
That link works fine for me. Right click it and choose "Save As..."
As for the SD card, have you formatted it in a PC or an Android phone? Better to do the latter if you can. As for the version you need to use, what was your current ROM? There are plenty of threads in the dev section describing what the versions are...

Hi Floating Fat Man
Sorry about the delay in answering. ( Time difference).
We are having issues with the only SD card we have. ( super expensive here) We also have the Nokia N8 android phone but no where can we find how to format the SD card ( we can format the phone but not the SD card ).We managed to get it to show on the PC and we can format but to a generic format and not the FAT filesystem. I know the Nokia N8 android is a rare phone in the USA cos all the phone shops were swooning over it and saying WOW, we dont have that. So help on formatting the SD card is proving hard to come by. Do you have any suggestions. Oh we copied the file you mentioned to the root on the generic formatted SD card and again got the yellow exclamation mark which was no surprise. I know I have bricked the tablet but I will be using it as a real brick very soon as it goes out the window LOL
Acer support has suggested I send it in for repair and that may be the only option left if we cant get this SD card up and running
I thank you for your help, I certainly have learned alot so far and I have a feeling its only the tip of the iceberg.
Thanks again

Your PC should give you an option to format the card to FAT32, which is the right format. Alternatively, a link to a format tool been posted on these sections recently in one of the many threads discussing the same issues, but I don't have a link handy, sorry.

[Q] Error message written in red

Hello and sorry for my English I watch it on my tab Iconia if there had an update and me to find but when he finished it restarts and now I have a message written in red marked with "Boot verified failes ... "that appears every time I start it and I even entered the art that make recovery and I hope it's not Gave thank you kindly help me

sounds like RED text could be in BOOTING or recovery area?
maybe do a "HARD RESET" to the left of your USB port on right side.
You'll see word "RESET" and a pin hole to the right. use a small pin to reset Tablet.
Sounds like you never can get to Home screen.
I'm guessing, you have a STOCK ACER BOOT Recovery, so this might not help.
Try to BOOT into recovery MOD (just in case you have a CWM Recovery).
I don't think you have a Mod'd recovery. (but doesn't hurt to check and see)
HOLD down [Volume Down (left side or closest to power button)] + [POWER] long press = boot Recovery
This maybe best solution (if all else fails)...
1. Download a ACER A500 HoneyComb v3.1 of a stock acer ROM (cus it's easier to ROOT (optional), and work on. If it works, you'll have 3-4 updates from OTA to get to v3.2.1 (most current) or you can use it to easily get to any CUSTOM ROOTED ROM.
2. place any STOCK ACER ROM on your EXTERNAL SD Card and rename it to "update.zip". The tablet on boot should look for any "update.zip" file before proceding to Desktop. This might wipe all your data + old ROM, but if works at least you'll be fixed. (getting past boot screen)
*** "update.zip" can only be a stock Acer a500 ROM (not custom). Acer will only be able to read it's own versions (coded)
ROM's Here, get one that is v3.1 (not 3.2 my opinion, cus v3.2, v3.2.1 has bootloader locked and is tuffer to work with, especially since you already have problems) http://forum.xda-developers.com/showthread.php?t=1113878
I suggest this GEN_1 (since you are probably not in USA) Acer_A500_4.010.41_COM_GEN1 : http://www.multiupload.com/DLBRQWGE03

[Q] Acer iconia A500 Tablet wont go into recovery mode

I have had my acer iconia tablet for 2 months.
I am a total noob when it comes to rooting, flashing or installing new roms on any android device. Never done anything like it.
My tablet just boot loops and all i get is "green android icon holding a yellow triangle with an exclamation point".
What can i do. I have seen a youtube video of a user holding down the volume down + power key and he is presented with a menu to factory reset and cache resetting and all that good stuff. I do not get any of that. Any help would be appreciated.

the menu that you seen in the video. was likely CWM RECOVERY. You do not have that menu due to the fact you do not have a custom recovery installed. the android with exclamation leads to believe you have acer recovery. Its limited Only able to flash a ACER Signed update.zip only .
Reply back with exactly what you did with details about rom version and so on . So someone can better help you. To get the right help we need to know how you broke it..
At this point Do not do anything until you know you are doing the correct fix for your situation.. You are NOT Bricked.. you just have a bad UPDATE.ZIP FILE OR Bad format on your sd card..
Help is close by..

To be honest i really do not know what rom version was used. Like i mentioned before. I myself have never rooted or altered an android device.

From where you are right now in a boot look .. where do you want to end up.. ROOTED ... STOCK TO WHERE YOU can accept the acer OTA. when they push them..
sounds like you may be able to reset the tablet withe hole next to the usb port.. You have to push quite hard to get it to push the Button..
Im guessing due to the lack of information you are providing.. Sorry..

Thanks for your help. The darn thing is still doing the same thing. Guess i got to do a little more research.

If you're asking for help you need to describe what actions exactly you have taken in order to reach this state (as Erica suggested) of your tab. From your post 1 thing is clear - your tab is unable to boot, but what has been modified before remains a mystery.

joester818 said:
I have had my acer iconia tablet for 2 months.
I am a total noob when it comes to rooting, flashing or installing new roms on any android device. Never done anything like it.
My tablet just boot loops and all i get is "green android icon holding a yellow triangle with an exclamation point".
What can i do. I have seen a youtube video of a user holding down the volume down + power key and he is presented with a menu to factory reset and cache resetting and all that good stuff. I do not get any of that. Any help would be appreciated.
Click to expand...
Click to collapse
Yeah, probably my guess, is you tab started to do an OTA update, and as in a lot of cases, it failed. And you're stuck with where you are now.
If using the pinhole reset near the PWR button doesn't work (a hard reset), then I suggest ;
1. Make sure your tab is charged.
2. Go to this thread, and select one of the rom update packages.
3. http://forum.xda-developers.com/showthread.php?t=1113878
Use one of the HC 3.2 update files near the end. Note that the Megaupload file no longer works.
Note that some of the packages are encrypted, so you will need to use the "decrypt" tool he has listed there in his 1st post. Copy it to PC, run it, select your encrypted rom, and let it do it's thing. This will give you the same rom, only states "decrypted" at the end of the file name.
4. Open the rom using Winzip or 7zip. Remove the update.zip (do not extract the contents of it), and copy it to the SD card (replacing a current update.zip if there's one there).
5. Holding either Vol- press and hold PWR. This should force the tab to install that update.zip (you should see some text on the screen, then you can release both buttons. Hopefully it will install.
Post back results please.

Just to complement Moscow Desire's advise: It's Vol (-).

drkalo said:
Just to complement Moscow Desire's advise: It's Vol (-).
Click to expand...
Click to collapse
Thanks! I can never remember which one, as I've never had to use it
Edited the instructions.

Moscow Desire said:
Yeah, probably my guess, is you tab started to do an OTA update, and as in a lot of cases, it failed. And you're stuck with where you are now.
If using the pinhole reset near the PWR button doesn't work (a hard reset), then I suggest ;
1. Make sure your tab is charged.
2. Go to this thread, and select one of the rom update packages.
3. http://forum.xda-developers.com/showthread.php?t=1113878
Use one of the HC 3.2 update files near the end. Note that the Megaupload file no longer works.
Note that some of the packages are encrypted, so you will need to use the "decrypt" tool he has listed there in his 1st post. Copy it to PC, run it, select your encrypted rom, and let it do it's thing. This will give you the same rom, only states "decrypted" at the end of the file name.
4. Open the rom using Winzip or 7zip. Remove the update.zip (do not extract the contents of it), and copy it to the SD card (replacing a current update.zip if there's one there).
5. Holding either Vol- press and hold PWR. This should force the tab to install that update.zip (you should see some text on the screen, then you can release both buttons. Hopefully it will install.
Post back results please.
Click to expand...
Click to collapse
Those vache-android.com links are not working. Do i need to have all of those files per update for the whole thing to work.

joester818 said:
Those vache-android.com links are not working. Do i need to have all of those files per update for the whole thing to work.
Click to expand...
Click to collapse
Be patient. Try later. Vach's server is probably overloaded due to the leaked ICS Rom.
You only need to get 1 of the A500 update roms. It's actually a fully signed rom in the file "update.zip" Just decrypt rom you the original rom you downloaded using the instructions, use winzip or 7zip to open the decrypted rom, remove the update.zip and copy it to your sd card.

And Then?
joester818 said:
Those vache-android.com links are not working. Do i need to have all of those files per update for the whole thing to work.
Click to expand...
Click to collapse
Hi,
did u succeed?
Rgds,

trying to recover A500 - boot recovery failed
Hi - I'm trying to reset and recover my son's A500 tablet. I copied one of the HC 3.2 Update.zip files to a microSD card, then held down Power and Volume - buttons. As long as I hold down the Volumn down buttin, the tablet seems to be stuck in a never ending cycle of loading the update and booting recovery image kernal, then restarting, then loading the update.zip file and booting recover image kernal, etc.... If I let go of the Volume Down button, I get in red letters "Boot Verification Failed" message, and it stops.

im trying to help fix an a500 tablet. apparently the tablet gets stuck at the acer logo. when i hit power and the volume button i get some lettering in the top letft. I took the advice here and went and downloaded one of the HC 3.2 updates. copied the update.zip onto the root of the Sd card and then put it back in. I hit the same buttons again and the letters came up. so i assumed things were working. all of a sudden i get an android with a blue diagram in its belly (kind of like it was loading) and then it froze. after waiting for a second I got a second android that popped on the screen and this one is laying on its back with its chest open and a red triangle is showing....So I don't know exactly what I did wrong here. Any help would be appreciated. I am not exactly sure what he did to mess it up. I believe he was trying to install a custom rom and did not go about it correctly and therefore messed up an update and now he has nothing. so im not sure what to do exactly.

Moscow Desire said:
Yeah, probably my guess, is you tab started to do an OTA update, and as in a lot of cases, it failed. And you're stuck with where you are now.
If using the pinhole reset near the PWR button doesn't work (a hard reset), then I suggest ;
1. Make sure your tab is charged.
2. Go to this thread, and select one of the rom update packages.
3. http://forum.xda-developers.com/showthread.php?t=1113878
Use one of the HC 3.2 update files near the end. Note that the Megaupload file no longer works.
Note that some of the packages are encrypted, so you will need to use the "decrypt" tool he has listed there in his 1st post. Copy it to PC, run it, select your encrypted rom, and let it do it's thing. This will give you the same rom, only states "decrypted" at the end of the file name.
4. Open the rom using Winzip or 7zip. Remove the update.zip (do not extract the contents of it), and copy it to the SD card (replacing a current update.zip if there's one there).
5. Holding either Vol- press and hold PWR. This should force the tab to install that update.zip (you should see some text on the screen, then you can release both buttons. Hopefully it will install.
Post back results please.
Click to expand...
Click to collapse
I to have had the same problem with my Acer Iconia A500. I followed the instruction and booted the Acer...got to the screen with the Android robot standing upright with the spinning in his stomach...goes to about 1/4 of the way and doesn't go any further....looks like it's trying to continue but has been at the same place for over an hour. Do I need a different rom perhaps?? I used A501.000.00_4.037.01.emea_tmp

mizzle54 said:
I to have had the same problem with my Acer Iconia A500. I followed the instruction and booted the Acer...got to the screen with the Android robot standing upright with the spinning in his stomach...goes to about 1/4 of the way and doesn't go any further....looks like it's trying to continue but has been at the same place for over an hour. Do I need a different rom perhaps?? I used A501.000.00_4.037.01.emea_tmp
Click to expand...
Click to collapse
Well, you can try this. Below are links to update.zip files already decrypted on my server. I have renamed them, only so you can keep them separate. You will have to change the name to "update" (update.zip) and copy one to ext sd card. Reboot holding Vol (+ or -) and PWR. See if they install. You may have to try each until one installs as there is no way to predict which one will work.
http://d-h.st/KXl
http://d-h.st/gw8
http://d-h.st/2cm
http://d-h.st/Zf8
This is probably the easiest method to try first.
MD

the "41-125-03-update.zip" seem to work for me. The status bar finally is showing but it doesn't seem to be moving. It moved to 1/4 of the bar and it stayed there. Last time it did this, it stayed there for over 2 hrs. I hope it's working this time. Anything else I could try?
My tablet was working fine and I left it there to go to work, coming back I found it on the Acer logo. Many search brought me here.

update ========
tried and tried and tried.......a few times that the status bar did come up, many times it stuck at around 25%. A few times it got all the way to 75% of the bar. It refuse to go farther when I left it there all night. It finally died when the battery was complete drain.

Acer A500 Stuck on ACER Logo (not rooted) finally fixed!
Just wanted to post some positive things for a change. My ACER A500 tablet (not rooted and running ICS 4.0.3) was working fine two months ago and I wanted to watch an ESPN3 football game on the tablet which I then hooked to my HD TV via the HDMI cable. For about an hour, all was fine then the tablet did an uncommanded reboot and then I had the android figure with an opened belly followed by an android laying on it's side with an exclamation mark. On the next restart, my tablet would not pass the ACER logo screen. After reading many posts with the stuck ACER logo, I was not sure how to proceed exactly. I have rooted a 7 inch tablet last year but I could not get my act together on the exact steps to revive my tablet. Finally I came across this post with the ACER ROMs already decripted which removed many questions I had about the exact steps to create an "update.zip" file for my SD card. Based on just downloading the file from your web site and renaming the file to "update.zip" and moving a copy to a formatted SD card, I was ready to try the process to load another ACER file to my tablet. On my first attempt, I tried the file named "206-03" based on a guess of the naming convention used or maybe blind luck. I preformed the PWR button and Vol down button combination with the "update.zip" file on the micro SD inserted in my tablet. The tablet started with three lines of text and then the android figure with it's door open and activity inside the android. This screen stayed then with a completion bar followed by a large text screen warning not to turn off tablet. After about 15 minutes total, my tablet was alive with a request to select my country. Bottom line, taking the steps to put the decripted file on your server and the simple button combination to start the reload process allowed me to get my tablet working great running ICS 4.0.3. I just wanted to post a success story and follow up. Thank you Moscow Desire for taking the extra steps to help the uneducated user!

Anyway I can check if my ROM hardware are working properly? I have tried all the update.zip and all of them show a dead android at the end. I can't even tell if it read from the microSD.

My tf101 is bricked !! Please help!!

My tf101 cannot enter recovery anymore
when i try to enter recovery ,
there is a " ! " on the robot , then tf101 reboot automatically
then freeze on the ASUS logo page
I cannot boot up the machine in normal mode too !
my tf101 is B70 version, someone help..thanks

! with the Android guy is recovry, stock recovery.
instead of Vol up to get into revovery, wait till you get options to cold boot or wipe device.
try booting that way.
also what were uou doing when it gotvstuck at that screen?

baseballfanz said:
! with the Android guy is recovry, stock recovery.
instead of Vol up to get into revovery, wait till you get options to cold boot or wipe device.
try booting that way.
also what were uou doing when it gotvstuck at that screen?
Click to expand...
Click to collapse
i tried cold boot , but it said cold booting up linux .. but no response
i tried wipe device , but it still freeze on ASUA screen too
yesterday, i try to root and install CWM via Prime V4.5
then the device comes this .....
Thanks ...

Never heard of that root utility before. You may not have used the right rooting utility for your device which can cause a brick situation. Also, are u sure u dont have the tf 101 and not thr tf prime? The vipermod utility found in the tf prime forum will root ics for both the 101 and prime. My suggestion is that u make sure u have the right device and search the right forum for brick recovery, unroot, or return to stock threads. They are usually found in the development sections.
Sent from my SGH-I777 using XDA

viperMod PrimeTime 4.5 will only root the TF101 and shouldn't be used to install CWM. That's why it bricked.

cholywell said:
viperMod PrimeTime 4.5 will only root the TF101 and shouldn't be used to install CWM. That's why it bricked.
Click to expand...
Click to collapse
i had an issue that was caused by lack of sleep last night that i might be able to help this guy out.he never used it to flash CWM.. he rooted it and never flashed from within the CWM app. The stock recovery doesn't have options for choosing files ect..

victor1144 said:
My tf101 cannot enter recovery anymore
when i try to enter recovery ,
there is a " ! " on the robot , then tf101 reboot automatically
then freeze on the ASUS logo page
I cannot boot up the machine in normal mode too !
my tf101 is B70 version, someone help..thanks
Click to expand...
Click to collapse
I might be able to help you... I saw your post around 4am. I had the same problem kinda. Was asleep most the day (got done at 6am).
I rooted with viperMod PrimeTime and it worked !
BUT i forgot to FLASH CWM RECOVERY from inside the app and proceeded to install the new ROM after root was made USING the CWM app. What happened in my case , the CWM app restarted trying to flash the new ROM, WITHOUT CWM being my recovery instead rebooted to STOCK recovery and something glitched up. I had the same thing as you stuck on Eee pad never re-starting. Cold boot wouldn't work or full wipe..In my case something conflicted.
Below is the NVFlash of the 3.2 Build of 8.6.5.13 (Latest Build). You need to re-flash again using APX threw your USB connected to a PC (it self installs) :
http://www.tabletroms.com/forums/tr...stock-3-2-recovery-roms-unbricking-tools.html
the links are in Grey btw and says US version, ect ..read everything but its very straight forward... ill explain what i did toward the end of the post to simplify it since it took awhile to figure it out. Ill add side comments threw the process that explains better than the link.
Attention: These tools are designed to bring your device back to working condition. They are great for getting back to stock if you need to send your device in for repair or you need to downgrade to stock in order to root your device, etc.
Instructions for Windows users:
1. download the file from the original link i gave above. NVFlash of the 3.2 Build of 8.6.5.13 (Latest Build) USWindows
2. unpack zip to desktop.
3. Press Volume up and Power at the same time on your Transformer to enter APX mode, connect to pc (hold for about 7 seconds). Basically, Power off.. THAN, power and Volume up at the same time to enter APX mode. IMPORTANT!! the screen remains BLACK like its frozen ,with no writing or indication something is happening. that's normal and the original poster in the link never mentioned it. That is APX mode..
4. drivers for APX are in there if you need them..inside the windows downloaded file its called NVFLASH towards the bottom
On your PC go Device manager.. if APX is working correctly and the Transformer is in APX mode it will appear as an exclamation on the device manager named APX.. you cant miss it.. it stands out. On my Windows 7 PC it changed and said Asus USB (or something like that)
5. double click Run Download.bat file and let run! everything is prepackaged so no copying files, etc. In the same file you downloaded that you unzipped named Windows its the 4th file that says "download" with a gear looking icons.
Your Transformer (based on what happened with mine) will go threw a self install like its pushing files and flashing it..the black screen looks like its being pushed the files and reflashing without a recovery. Your going back to stock. if you dont see anything on your Transformer screen after running/double clicking the Download.bat file ....Right click on APX in the device manager , properties, Drivers, update Firmware, choose manual install and find the Downloaded.bat file and click it. That should do the trick..I did both and only noticed the Transformer lighting up after manually pushing it threw APX.
6. After the device reboots power it off. Then hold vol- and power until you get the option to erase your data.... Select the option to wipe data.
7. Download the latest update from the Asus website if applicable and follow the manual instructions. This step may not be necessary if your OTA update worked or my nvflash is the latest version. US update on there site is 9.2.1.17.Its the only one...
What i did was go back to stock since i didn't see any interesting ROMS..Point is THAT unbricked my device by flashing it in APX mode when it was connected to the PC.
I did use ViperMod again to Root, but used the Clockwork mod app in my Transformer to FLASH CWM RECOVERY to try a few ROMS out.
After trying a few of them out i choose to revert everything to stock, unrooted and reflashed STOCK recovery.
Hopefully that helps you out.. it did work for me...

Thank you so much it worked great

Lantek23 said:
Thank you so much it worked great
Click to expand...
Click to collapse
Glad i could help

Sorry to dig up slightly old threads, but I have a question for you. I have a TF101 that I was trying to update to ICS. It is currently running 3.2 courtesy of the unbricking tool listed in this thread. I had to unstore it as it was bricked from a bad install. That was many moons ago. It won't show an updaate listed, so I decided to go with the manual route. I downloaded the appropriate update (my device lists WW version) loaded it on an SD card had the install prompt come up and rebooted to install... For a split second it shows the android with the gears like it is installing the update and then shows the android with a triangle and exclamation mark. After that, nothing. I have to reboot to get it off that screen. Upon booting, I get a message saying system update failed (2) unknown error. Any ideas?

If Im not mistaken, the zip file you download (I guess from asus?) contains another zip.
Thats the zip you should place on your SD card, did you do that?

Also try renaming that zip to EP101_SDUPDATE.zip (the one extracted)

I already had the zip extracted, and renaming didn't do anything.

Killa357 said:
I already had the zip extracted, and renaming didn't do anything.
Click to expand...
Click to collapse
Are you rooted? Did you remove any system apps?
Another thing to try is on your micro sd card, make a folder name ASUS and inside that folder another folder call Update, inside the Update folder put the extracted zip file (don't rename). Turn off TF and turn it back on, see if it will detect the update file.
If that fail, you did mentioned you use the unbricking tool, use that NVFlash to flash a compatible ICS ROM

It isn't rooted anymore since I ran the unbricking tool, and no system files were modified. Placing it in Asus>Update folder didn't work. I may end up having to really do things manually...

Killa357 said:
It isn't rooted anymore since I ran the unbricking tool, and no system files were modified. Placing it in Asus>Update folder didn't work. I may end up having to really do things manually...
Click to expand...
Click to collapse
You don't need to be root to use NVFlash.

Just when with a slightly older version of the update and it worked. There may be something wrong with the file Asus has hosted.

Hi
I have a slightly different problem. I have rooted my B60 serial number, it has the ICS from ASUS on it and it boots fine, its rooted and it works. Now the problem is I thought lets try a clockwork mod and play with custom roms.
So I set my win 7 up to adb etc, and pressed power button volume button - and off to recovery I went...
but all I got was a little green android on its back chest open and an exclamtion mark. No adb fastboot devices command.
I seem not to have a recovery nor a way of forcing a custom recovery.
Should I NV flash or just be happy the tab works and leave well alone?
Any other answers since a lack of recovery may come back to haunt me sooner or later.
I also tried the power button vol uyp for 7 secs and nothing happens I can get to the cold boot erase data option on power down, don't want to do that yet since Im not sure what data gets erased and I may have a totally non working tab.

Use RecoveryInstaller to install cwm recovery

Use RecoveryInstaller to install cwm recovery
This is my problem I can't get recovery - nor can I get adb to see the device. It shows as a hard drive/storage device but not in adb.

[Q] Cannot get CyanogenMod v0.9 to install - can't get CWM to reboot into recovery

ThinkPad Tablet A400
Android v. 4.0.3
Have an app that needs to run on Android 4.1 and quickly found out this 2 year old device was pretty much left unsupported since about 3 months after I bought it in May of 2012. So, I located the links to xda-developers and dove into the install process.
Got the device to Root following install directions etc.
Cannot get the device to reboot into recovery mode from ROM Manager nor via ROM Installer.
Tried installing the CyanogenMod v0.9 anyway from inside either aforementioned utility (from the .zip file), just reboots back to the normal state.
I'd pay to download & install Android 4.1 on this device, seriously...just lost 6 hours of time attempting to do this ROM upgrade.
any suggestions?

First thing that comes to mind is that you should use the volume up button multi-press on device power-up to get to Recovery Mode.

pwstein said:
First thing that comes to mind is that you should use the volume up button multi-press on device power-up to get to Recovery Mode.
Click to expand...
Click to collapse
I've tried various combinations of that Vol button....still stubbornly refuses to go to CWM.
Now, I am running Android 4.0.3..perhaps that is the issue, ie. perhaps the CWM image file was intended to be used on TPTs running Android 3.x.
It'd be nice to go to a site and buy a $50 OS load....

Well....wonders never cease. I happened across a post talking about the TECHNIQUE to reboot the TPT into CWM...so, sure enough...I got the puppy into CWM.
HERE 'tis for the rest of us nuves out there:
Entering/Booting CWM Recovery on the Thinkpad Tablet
Shut down your Thinkpad Tablet
Press the power button until the Tablet vibrates
Keep pressing and releasing the volume up button until you see Booting Recovery Kernel Image in the upper left corner. It's all about timing of when the volume up button is pressed. That's why it's a good idea to just keep on pressing and releasing the button until the message appears.

Well i continued on with the Jelly Bean load from the xda-developers...and after reboot to ver 0.92 the tpt seemed to freeze on the os boot screen.
So, i fell back to the 4.0.3 os and will read-up on what can freeze the reboot into 4.1 android.
CWM is a cool program..gotta say it.

Can't get it to install CWM
Tried numerous times but now I have lost my original recovery and it just loops,
Changed permissions but won't go and when I am in the recovery boot after pushing the volume button it just reboots as there is nothing there suggestions?

Honestly, the best thing you could do is get something newer/better supported. I hate saying that, because I bought the 64gb version right around the same time you did. The tablet had so much potential with the pen, USB, sd slot, and even pci-e, but it suffered from non-existant Lenovo support, and very little dev support. Koshu's work on it was amazing, but without trim I feel like I have to constantly wipe and start fresh to do anything with it. Clearing dalvik from time to time helps, but not as much.