Guys read this and give thoughts please!!!! - Galaxy S I9000 General

Ok this will be a bit lengthy but please bare with me and read...
Ive been running Darkyy 10.1 EE for months now and every has been fine.
Easily a couple of days battery, no force close issues of any sorts... Everything has been perfect.
Then the other day i noticed my battery started dropping fast. NO THIS IS NOT A BATTERY DRAIN THREAD SO PLEASE READ ON.
I took my phone off charge the other night within seconds of hearing the beep for battery full and the fully charged icon in the top right of the bar stayed there for a few seconds ( like maybe 10 ) and then the battery level dropped to 80%.
I thought hhmmm thats not right but left it and went to bed.
6 hours later i woke up to 31% battery.
I thought something must be running killing my battery so i did a reboot...
Now this is where it gets weird. Read on my friends...
after i rebooted the phone it kept rebooting itself every 2 minutes or so.
I pulled the battery of for 30 minutes and put it back but i had the same problem.
When i got home i did a factory rest and wipe cache partition and decided to flash Darkyy 10.2...
I had the same problems as above only now when my phone rebooted the battery lvl would drop by 20% then next time raise by 5% etc etc
NOW THIS BIT IS SCARY BUT READ ON!!!
I decided to flash back to froyo with ezbase using repartition to see if that would help.
I plugged my phone into the computer and nothing happened!!!! My computer wouldnt recognise my phone at all neither would my phone start charging whilst plugged into the computer.
I managed to get my computer to see my phone by booting into recovery and and then download mode and flashed ezbase.
Again same problems. So i thought OK this might be an insurance job so i flashed it back to stock JPY from samfirmware.com. I plugged it back into my computer and my PC says "the USB device you have connected has malfunctioned and windows cannot recognise..."
I have had my phone unplugged over night but the icon on the bar is still there showing USB connected, and in the pull down shade there is still the option to connect USB to copy files.
I have plugged it in this morning and it started charging but windows didnt even recognise that there was anything attached at all! No beep no fault deviced attached message... Nothing!
Oh i would also like to mention that when i flashed ezbase and tryied to do a reboot i would get the battery icon for a second like if you charged while the phone was off and then it would power down again... The only way i could get the phone to boot back up was to flash EZbase again with auto reboot ticked!
Yes that was very long sorry and thankyou to those who took the time to read it.
If anyone has any thoughts on why this would have happened please post.
Do you think this is something caused by the custom rom or is this a hardware issue completely out of my hands?
Thank you again for reading!

Have you tried another battery?
Sent using geek power

First, I would try to check if its a hardware problem.
For that burn a stock rom and see how it is doing. If its working fine with stock, without any problem, then obviously its ROM issue.
Else if the stock also gives you the same problem, then I would say its a hardware problem.

gsw5700 said:
Have you tried another battery?
Sent using geek power
Click to expand...
Click to collapse
I dont think its a battery issue because the battery wouldnt prevent the computer from seeing the device would it?
mammenj said:
First, I would try to check if its a hardware problem.
For that burn a stock rom and see how it is doing. If its working fine with stock, without any problem, then obviously its ROM issue.
Else if the stock also gives you the same problem, then I would say its a hardware problem.
Click to expand...
Click to collapse
Im running stock JPY right now and have the same problem

Could it be a damaged usb port, so that it doesn't always charge properly, and doesn't always detect the phone correctly when connected to the computer? That might explain the problems... Especially if that port is getting worse all the time.
Can you get it to detect on the computer if you wiggle the usb plug to the phone? Have you tried a replacement usb lead?
It does sound weird. Hope you manage to sort it out.
Mike
Garbled meaning induced by swype!

don wadte time if ur phone dosnt work on stock then its the port tht got damaged and the hardware,,,,something wrong .....better go to a service center..don expirement ,cause it might damage it more

I have just dropped it off at the shop i bought it from and they are sending it away for repair.
2 weeks of nokia 3210 magic for me!
Thanks for replies guys.

Related

8125 Dead

I have a 8125 and I was able to unlock it fine. After unlocking it I upgraded to the underground crossbow edition rom - which the 8125 rebooted and was running. I tried out a couple things and everything seemed to be running/working fine. It was getting late so I put it down and went to bed. This morning when I got up the phone was off so I went to turn it on and nothing happened. I figured it just ran out of battery power plugged in the charger and guess what no red light on. I have tried everything under the sun but I cant get it to charge or startup. Anyone have any ideas? It was working fine.
i know u said u've tried everything and i don't mean to sound like i'm takin the buscuit, but leave it on charge for n hour, then try bootloader. taking the battery out completely for a while could work.
i had so many problems with crossbow! think this was one of them.
Unplugged
Well so far I left the charger plugged into the phone with the battery in it for over an hour now - with no luck. The red charging light doesn't even come on. Did you have that problem? I also left the battery out and plugged in - still nothing. Tried taking the battery out and then putting it back in while plugged in - no go.
I have not tried the "bootloader" - but the phone will not turn on at all or respond in anyway. Its in a powered down state (or so it seems) - I dont think bootloader will work?? But I dont know anything about bootloader - is it on the ftp site and how do I use it?
Any chance the battery could have been completely discharged?..just a thought. I think i read that completely flat batteries wont charge up via usb. Disregard if thats a silly suggestion, just thought id offer my two cents.
try getting a new battery and see if it boots up...it can be your battery.and you are trying to charge with an AC adapter right?
Wall Charger
I am charing it via the wall charger (not usb) and I am going to try to get another battery. Just weird that I never had a battery problem until I install the wm6??!! Unless the damn thing drained my battery dry and somehow damaged the battery. I called Cingular and they are sending me another unit as its still in warranty. So we'll see when I get it - I will try the new battery. Strange. Very Strange - because everything was working last night.
Strange
Well after leaving the battery out all afternoon I took a go at the phone again, put in the battery then turned it on. It actually started booting up - showing the WM6 bootscreen. After about a minute it shut down like it was out of power. Strange. I know the phone is not bricked because if it was it wouldn't have just done what it did. Anyone have any suggestions how to fix it?
Could be a bad battery. You need to test out with some one else battery
HuddaDudda said:
Well after leaving the battery out all afternoon I took a go at the phone again, put in the battery then turned it on. It actually started booting up - showing the WM6 bootscreen. After about a minute it shut down like it was out of power. Strange. I know the phone is not bricked because if it was it wouldn't have just done what it did. Anyone have any suggestions how to fix it?
Click to expand...
Click to collapse
HuddaDudda said:
Well after leaving the battery out all afternoon I took a go at the phone again, put in the battery then turned it on. It actually started booting up - showing the WM6 bootscreen. After about a minute it shut down like it was out of power. Strange. I know the phone is not bricked because if it was it wouldn't have just done what it did. Anyone have any suggestions how to fix it?
Click to expand...
Click to collapse
u shud have plugged it in while it was booting...did u?
New Battery
Well I finally got the new battery I ordered today. When I put it into my phone it will boot into wm6 fine but will not sync with activesync 4.0 or charge via USB or plugged into the wall. I uninstalled activesync, rebooted my computer and installed Activesync 4.5 - but still no luck with the phone via usb syncing with my pc. Also when the phone in plugged into the wall via the wall charger it does not charge. I am beginning to think the port on the bottom somehow was disabled from the rom update, although I dont see any posts with people having that problem. I guess my next option is trying to reflash it to stock rom via a sd card since it wont connect via USB - however I can not find the information step by step how to do this. Can someone point me in the right direction?
Try going to the bootloader screen: Turn off your phone and then hold the camera button while you turn it on. When you are at the Rainbow screen (thats the bootloader) plug in your USB cord. You should see in the bottom left (above the left soft key) where it says USB. If it doesn't then I'd say your USB port is broken (I'm not aware of any ROM being able to disable that).
As for flashing from the SD card, I believe thats documented in the Wiki...

bricked phone??

hey all, like most people here, i've been flashing my phones like crazy for the past couple days to trying out all the new roms it's been fine for the last couple days and sundenlly it just stop working this morning. It wouldn't turn on or anything, when i plug the usb in, window gives me an error as it cannot connect to the phone. I try the charger and it wouldn't charge(the charging light on the phone wouldn't turn on). I just got my phone replace last week due to theft. So is my phone bricked? I've flashed my phone alot and each time i wipe everything, could that be the problem? if i take it back to sprint store you think they would send me a new one? thanks.
Take it in and find out...
Just curious... what rom were you running when that happened?
cptkool said:
hey all, like most people here, i've been flashing my phones like crazy for the past couple days to trying out all the new roms it's been fine for the last couple days and sundenlly it just stop working this morning. It wouldn't turn on or anything, when i plug the usb in, window gives me an error as it cannot connect to the phone. I try the charger and it wouldn't charge(the charging light on the phone wouldn't turn on). I just got my phone replace last week due to theft. So is my phone bricked? I've flashed my phone alot and each time i wipe everything, could that be the problem? if i take it back to sprint store you think they would send me a new one? thanks.
Click to expand...
Click to collapse
Pull out the battery, remove charger.
Put the battery back in and dont press anything. Plug it into the wall and see after ~60 seconds you get a charge light.
I just got my phone replaced with the exact problem. Took it to sprint and they ordered me a new one under the HTC warranty, no problem. I didnt say anything about flashing just that it stopped charging and would not turn on anymore.
natelw said:
I just got my phone replaced with the exact problem. Took it to sprint and they ordered me a new one under the HTC warranty, no problem. I didnt say anything about flashing just that it stopped charging and would not turn on anymore.
Click to expand...
Click to collapse
Just remember that if they get the phone to boot after you turn it in and they find out its rooted/ROM'd that they can fine you the entire price of the phone. Not trying to scare you but it has happened to people. However, it does seem there have been quite a few complaints about USB "issues".
dfbonney said:
Just remember that if they get the phone to boot after you turn it in and they find out its rooted/ROM'd that they can fine you the entire price of the phone. Not trying to scare you but it has happened to people. However, it does seem there have been quite a few complaints about USB "issues".
Click to expand...
Click to collapse
I too have had the usb charging issue. Try moving the usb cable around in the phone and see if it contacts. Mine does by lifting up on it. I called Sprint to see what they can do and they said that it is caused by the user. I laughed at them and said some not so nice words then hung up on them. Then took it to a Sprint store and they ordered a new one for me without any questions.
as a side note I am glad they are replaceing it cause now the speaker is blown and the paint is peeling from the power button.
Also, FYI, my kid's hero's charger died on him (the one out of the box). We thought his phone was broken because it would not charge or be recognized by the USB. Then we tried out my charger and, boom, all good.
Worth a shot....
alright guys, thx everyone for the reply, status update: I try everything that was mention here, pull bat and putting it back(several times), moving charging cables, letting the charger sit 60sec, none of it work. I know my phone wasn't out of batteries cuz when i went to sleep it was about 86% left, so i thought my bat blew out on me after a week of usage. so i just left my phone in my pocket and after a while it started getting hot, i was like wtf, and took out the bat immediately. i leave the bat out for about 30min, put that sucker in again, and voila, it power up, everything was back to normal...anyone know wth's going on? of course i'm very happy my phone is working again

Let Andriod die now have a paper wheight

ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Im guessing you cant run bootloader?
Maybe this is a warrenty jobby
If you know someone with another HD2, Try swapping the battery.
chrisizzle492 said:
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Click to expand...
Click to collapse
does it enter in bootloader mode?
retry flashing wm rom+radio
chrisizzle492 said:
i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
Click to expand...
Click to collapse
Hi Chris,
Please eleborate/clarify your OP, because I don't think anyone gets this... At least i don't! You say the screen doesn't turn on but the phone boots?! How do you figure that? Your device is actually on because you can receive/answer calls!?! :S
Sounds like your device has just BSOD (Black Screen of Death) which is discussed quite a lot here. Just press reset button or pull the battery (please tell me you have tried that before...).
If your device IS NOT powered on, please try this:
Does the device vibrate shortly when pressing the End-button? If so you should leave it connected to the charger for longer. If battery has drained too much it takes a while for the device to allow it to power itself up (prevention of overdrainage, which Lithium-batteries don't like very much).
Do you charge through USB, or with the supplied charger? I've had this before trying to charge it with a (different brand) microUSB charger. Turned out most chargers only give out 500mAh, whilst my normal charger (and car-charger) give out 1000mAh i believe. That might help.
You can order a cheap replacement battery from China (i got mine with dockingstation), which is already charged about 60% (for storage purposes).
BTW if your problem is fixed, please add the prefix [FIXED] or [SOLVED] to your topics title.
shufflez said:
Hi Chris,
Please eleborate/clarify your OP, because I don't think anyone gets this... At least i don't! You say the screen doesn't turn on but the phone boots?! How do you figure that? Your device is actually on because you can receive/answer calls!?! :S
Sounds like your device has just BSOD (Black Screen of Death) which is discussed quite a lot here. Just press reset button or pull the battery (please tell me you have tried that before...).
If your device IS NOT powered on, please try this:
Does the device vibrate shortly when pressing the End-button? If so you should leave it connected to the charger for longer. If battery has drained too much it takes a while for the device to allow it to power itself up (prevention of overdrainage, which Lithium-batteries don't like very much).
Do you charge through USB, or with the supplied charger? I've had this before trying to charge it with a (different brand) microUSB charger. Turned out most chargers only give out 500mAh, whilst my normal charger (and car-charger) give out 1000mAh i believe. That might help.
You can order a cheap replacement battery from China (i got mine with dockingstation), which is already charged about 60% (for storage purposes).
BTW if your problem is fixed, please add the prefix [FIXED] or [SOLVED] to your topics title.
Click to expand...
Click to collapse
i have restarted many times.
i use the wall charger.
but why would the phone boot but not turn on the screen or have the mic work?
remove your sd card and the battery. you may have to hit the rest button on the back after you plug the battery back in as well, but as long as you have the sd card out it should come back on. try plugging the phone into a charger and then remove the battery as well sometimes it'll wake it up so to speak. it's just a matter of playing with it. mine did the exact same thing and i freaked out for a little bit.
now if after all this it doesn't work and you've played with it for a while then yeah, best of luck to you =\. but whatever you do in playing with the battery and the charger, keep the sd card out until you can boot into winmo.
EDIT: never mind, i thought the phone wasn't booting. i misunderstood, but i went back and reread the original post. try reflashing your rom if you're in winmo and experiencing those issues. or take the sd card out and reboot.
i would suggest making an backup, as your phone turns on you should be able to estaplish a remote-connection with some (3rd-party-)software and do a hardreset.
if this wont work i would recommend setting it back to factory default (revert hspl if you have one and install stock rom) and send it in for warranty.
seems to be some major problem...
All this steps should be possible without screen turning on (working touchscreen may be needed for backup, but flashing doent need screen input)
if drive-mode is default for your usb connection and holding you from flashing you can do a hardreset and afterwards active sync will be default again and you can establish an active sync connection and flash
check if any of the pins that contact the battery are bended or broken, try to avoid removing the battery when you have to reset your hd2 because the pins are fragile
similar thing happened to me just last night!
I tried the jmz dual boot last night and I was nearly out of battery. I didnt look at any instructions I just installed it and restarted the phone to check out the new toy. it finally got done loading I chose android right away and I was walking towards the bedroom. when I went to see if android had fully booted and plug in the phone I had nothing! It was off. I decided that the battery must have died so I tried to turn it on and all that happened was the tmobile flash screen came up for a second and then it went right off, I got so desperate that I was going to do a hard reset but that wouldnt even work! the boot loader screen would just shut right off. I was suggested to try another battery we had at the house and bang it fired right up I took a wiff of my other battery and I dont know what happened but I think I let the magic smoke out cuz it is fried!
chrisizzle492 said:
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Click to expand...
Click to collapse
hello friend...i have a problem similar to this. basically when my phone is in android which i use alot if it dies in android, when i reboot it it will turn on for about a second to see my splash screen then turn itself off (the battery is obviously flat). so i plug my charger in and it stays on now but doesnt indicate charging....i boot it into windows mobile and the batt just stays at 0% but its still working. however once i unplug it it will die.....its like the battery is not in the phone. luckily i have two batteries and a dock which charges batteries, so i replaced the battery and everything works fine. once the battery that died in android was fully charged i tried it again and it was fine.................im guesing the moral to this story is dont let your phone die in android mode
I do notice my HD2 runs hotter while in android than while it runs in Windows.
I am not sure if that's an issue to this, which is why I never mentioned about it being hotter. Although my HD2 is noticeable hotter, it never gets to a point that I think I should unplug the USB due to overheating concern...
Just a few inputs from passed experience
I use TMOUS Stock 2.13.531.1 WWE ROM
2.12.50.2_2 radio (not stock)
k going to tmobile today to see if they have any extra batteries i can try.
then ill update
i went to tmobile. and while i was there i noticed the screen was turning on but very dim without backlight (barely noticable). but the rep helping me did not notice and i let it stay that way because tmobile is sending me a new refurbished phone as long as i send the old one (and the rep was totally cool he uses xda also and said they wont check my software and if they do they wont ask for the phone back). he also let me get insurance in case this happens again, instead i will just say its lost. so i basically killed 2 birds with one stone

[Q]Voodoo causing "battery is not connected" error?

Alright, so i sat down and did my first ROM flash (the clean update based off the DI01), then immediately downloaded ROM manager, and flashed the voodoo v0.2 with stock clock and voltage. Now every time I plug in the USB cable, I get the "battery is not connected" error. I have tried:
turning off phone, unplugging cable, pulling batt. then turning on, then plugging in cable
unplugging cable, pulling batt. while on, putting batt. in, turning on, then plugging in cable
... and every other possible configuration. I have left the battery out for 10 minutes now, and still no luck when I put it in.
suggestions?
EDIT:
waited a while longer, and it randomly worked. mods, feel welcome to delete this thread
It's been known to be related to phone being too hot.
hey..
That's what exactly what happened to me, so i actually flashed back to the stock rom
through the odin and wipe everything and started all over man..
I don't know..
Something is gotta be wrong with Voodoo kernel..
But in this way, i fixed it..
So i think im gonna stick with the lagfix for now..
and i guess when Dev comes out a different fixed verison, i'll take it again..
Good luck man
My phone was running at a fine temp to the touch, and I think the Battstat widget said it was at 30c, which should be fine. I think today i will flash over to a 1.1 or 1.2 Ghz voodoo kernel
Aidman...try this unplug the usb cord and shutdown pull the battery , then replace battery fire it up and charge....
post back results....
Voodoo busted my phone too. I could get the battery disconnected message to go away if I took the battery out and let it sit for a few minutes, but then it would come back later. It's a pain in the ass getting the message every time I try to charge my phone. Went back to stock until a fix can be found. My battery is nowhere near being hot when this happens, and I have only seen the message when using voodoo. I think I'll just wait for a later release. Too buggy for now...
Alright: for those of you who never read the full first post: THE PROBLEM IS SOLVED, thanks for everyone who decided to chip in. I had to try the battery pull about 10 times before it worked
Edit: I feel like an asshole after rereading my own post. I am sincerely sorry for my incredible stupidity.
aidman said:
Alright: for those of you who never read the full first post: THE PROBLEM IS SOLVED, thanks for everyone who decided to chip in. I had to try the battery pull about 10 times before it worked
Click to expand...
Click to collapse
I did read your post and understand the the problem wa solved for you, but not for me. I wanted to include my experience in case others are having the same issue. I was unable to fix the problem.
SnrSuave said:
Voodoo busted my phone too. I could get the battery disconnected message to go away if I took the battery out and let it sit for a few minutes, but then it would come back later. It's a pain in the ass getting the message every time I try to charge my phone. Went back to stock until a fix can be found. My battery is nowhere near being hot when this happens, and I have only seen the message when using voodoo. I think I'll just wait for a later release. Too buggy for now...
Click to expand...
Click to collapse
Not a lot of people get that error. I never did. And it never appeared either.
I had this issue too with the "no battery" indicator, and so did another individual in the lagfix release thread. No our phones were not hot, my own battery was nowhere near being hot, and we tried battery pulls, but that never worked. What worked for me was reflashing the voodoo 0.2 kernel on top of itself, the other guy tried that and had success with that too. You may give that a try, but I must say, that was only a temporary fix because after a while I got that annoying message back again.
I seem to have gotten rid of it for good, backed up all my apps in titanium, re-removed voodoo (be sure to get rid of "remove_lagfix" file when it's no longer needed), did a factory wipe, reflashed the stock Odin Kernel, did another factory wipe for the heck of it, then applied Voodoo, then reinstalled my data + app data using titanium backup (keep in mind I never wiped, restored, or returned system back to stock). Been running for a while, and I have yet to have the "no battery" annoyance and to be honest my phone boots quicker. So up to you, worked for me if you wanna give it a try.
Just wanted to update this thread. I have noticed that after flashing the voodoo kernel I too am getting the battery not connected error. However, I ONLY get this error when I have the usb cable plugged in when shutting down and starting back up again. If there is no usb cable plugged in when powering the device on, I have no problems with battery errors.
2 things stick out for me...
1. I had USB debugging on when doing the fix.
2. I removed the battery to go into initial Odin flash...PDA, etc.
The guide said my phone would reboot on its own, but it just sat at a blank screen. I had to unplug the cord and turn the power on. So do we have a fix for this yet?
i know earlier today my battery reading according tot he widget for setCPU said 66 degrees F.......which is kinda hard to believe seeing as the outside air temp is 80 degrees F outside and the inside air temp is 73 degrees F and my phone, although it had been sitting untouched for hours pluggen in inside, it was still on.....i cant believe the battery was running the best part of 10 degrees below ambient...even in idle state
Just flash the 1200 voodoo kernal u won't have that problem
Sent from my SCH-I500 using XDA App

[Q/Help] Phone will not turn off...?

When I turn off the phone, it vibrates to let me know it is off, and then it waits two seconds or so then turns itself back on.
I have done hard reset after hard reset, put the latest KE8 on and it still does it. Could it be a battery fault?
Do you have Advanced Power Menu installed?
Nope. It is now not letting me switch it on unless plugged into the charger.
If I switch it on away from the charger, it shows me a battery on the screen with a flickering yellow warning triangle with a thermometer next to it.
Any thoughts?
sorry to hear that!
i've had this problem about one or two months ago, after i flashed a new rom (can'r remember which one, was it lightning?). did almost everything i could
imagine (flashed other recovery, kernel, modem) and nothing helped. also a
complete fresh install (wipe everything before) didn't solve this!
the only thing which worked for me was to go back to my old rom. after that
everything was fine again!
so, i cannot say what causes this, but if you flash another rom it should work again! if not, try to repartition with odin, using one of the provided PIT files!
yep also had this problem when i first flashed cognition. my phone would reboot after turning it off. and if the battery went dead, when i plugged it into charge it would turn itself on instead of going to the battery charging screen. all i did was reflash the rom and all was fine.
This morning I updated to Android 2.3.4.
If I root like this:
http://androidflip.com/root-samsung-galaxy-s2-android-234-xxkg1-firmware/
Will it help do you think?
Just to update, it seems to be resolved now using this:
http://www.theandroidsoul.com/root-xxkg1-android-2-3-4-firmware-rom-on-galaxy-s2/
Thanks for your help guys!
And now its doing it again lol
I can live with it, but a couple of things like it thinking there is a USB cable connected seem to happen every now and again...?
hmm thats the same way as i did it but i didnt do the yellow triangle trick so im not sure about that. everything else is standard, thats how i flashed my rom and i only had your problem the first time i flashed. did you do the yellow triangle removal?
I did the remove triangle thing yea.
I do think it is a problem with the USB connector, it could be touching itself inside, possibly causing a shortage as it occasionally thinks a USB cable is connected.
So, if I turn off, it could be thinking that the charger has initiated connection and starts up to charge, but can't charge so just continues to boot.
I have plugged the usb cable in and with nothing at the other end, and nothing pops up. So it could be something like what I suggest. It has been ok for an hour or so now so fingers crossed lol!
lol that cud be it then. it wud make sence. might wanna get that looked at tho if you dont wanna risk damaging the phone. if its doing what you said, then it cud end up killing the phone if it shorts it out permantly. let me know how its going in a day or so.
Even on lock screen if you press and hold the power button for 8 seconds the phone does shut off, is it happening for ya?
I had this a few weeks back. Reflashing cf root kernel fixed mine.
minty1978 said:
I had this a few weeks back. Reflashing cf root kernel fixed mine.
Click to expand...
Click to collapse
Likewise, solved my problems with the phone rebooting itself instead of turning off.

Categories

Resources