I am a wildfire user from HK, and recently I rooted and flashed CM7 nightly by the procedure form 3xeno:
http://forum.xda-developers.com/showthread.php?t=1029318
Following is my case:
Since I have already OTA updated into 2.2.1 froyo, I downgraded the HBOOT and rooted with revolutionary method. Then I flashed CM7 with no problem occurred.
However I used the setcpu to overclock my device into 768MHz and i ticked the set on reboot by accident. I cannot reboot into CM7 loading screen so I flash the CM7 rom again and boot my device successfully. Then I also flashed the most updated kernel provided by 3xeno above. I haven't pay attention to the signal service since this point, no signal can be searched no matter what I did. I have already checked the APN setting and also doesn't work. The battery drain very fast (cell standby 82%) unless I turn on the airplane mode.
I reckon this is the problem of kernel/radio, and some developer said flashing radio is risky, so I flashed the RUU rom from Shipped ROM instead. I have tried both froyo and eclair RUU, even though some of the eclair disabled the touch input, but all the RUU cannot bring my signal back. Since the RUUs i flashed were with different radio version. I can still see the baseband version from setting=>about phone=> software information. The wifi can work with no problem.I didn't know what's wrong.
I have googled a lot and read a lot of threads in xda but still no idea. I decided to send it for repair. What should I pay attention to it before sending it for repair?
Maybe I forgot to mention something
In setting=>about phone=>Phone Identity
Model number : HTC Wildfire A3333
Phone number: Unknown
IMEI and Device serial number: same as the label under battery
IMEI SV: 01
In setting=>about phone=>Network
Operator name: Unknown
Signal strength: 0
Mobile network type: Unknown
Service state: Out of service
Roaming: Not roaming
I have tested my device with my friendsss' SIM cardsss, and the problem still persist.
ALL of the SIM cards, including mine, work well on the other phones.
Moreover, when I press down+power button, some sentences shown up:
SD cheking...
loading.. [PC49DIAG.zip]
no image!
loading.. [PC49DIAG.nbh]
no image or wrong image!
loading.. [[PC49img.zip]
no image!
loading.. [[PC49img.nbh]
no image!
after that it returned to the HBOOT menu and all become normal. They keep shown up no matter what RUU or CM7 rom I flashed. Is it a normal case or a sign of losing signal??
I have also installed the darktremor for app2sd before i flashed back the stock rom from RUU.
Sorry for my bad English.
Since you have s-off'ed your device with revolutionary, you have a custom bootloader, and thus no waranty anymore.. So it can and will cost you.
I don't know what is wrong with your phone.. perhaps stupid, but have you already tripple-checked your APN settings?
Erwin
Thanks for your suggestion. I've triple checked for the APN setting and sure that it is correct.
Maybe I forgot to mention something
In setting=>about phone=>Phone Identity
Model number : HTC Wildfire A3333
Phone number: Unknown
IMEI and Device serial number: same as the label under battery
IMEI SV: 01
In setting=>about phone=>Network
Operator name: Unknown
Signal strength: 0
Mobile network type: Unknown
Service state: Out of service
Roaming: Not roaming
I have tested my device with my friendsss' SIM cardsss, and the problem still persist.
ALL of the SIM cards, including mine, work well on the other phones.
Moreover, when I press down+power button, some sentences shown up:
SD cheking...
loading.. [PC49DIAG.zip]
no image!
loading.. [PC49DIAG.nbh]
no image or wrong image!
loading.. [[PC49img.zip]
no image!
loading.. [[PC49img.nbh]
no image!
after that it returned to the HBOOT menu and all become normal. They keep shown up no matter what RUU or CM7 rom I flashed. Is it a normal case or a sign of losing signal??
I have also installed the darktremor for app2sd before i flashed back the stock rom from RUU.
As far as i know apn has nothing to do with ur network unless you enable/ use gprs/3g internet connection.apn means access point name, and so it have nothing to do with the calls or network. I think ur problem is with radio, as u have a3333 u can try flashing a new radio, and some ruu does not contains radio,if it is a moded one,so there are chances that u have used one of them, go for it , try a new radio.
And in worst case it is a hardware problem,in which ovclck had done some thing wrong with ur processor or the radio module(hardware).in that case dont try to get ur motherboard replaced by htc,since u r out of warranty it will cost u a lot, so buy a new phn, nxt time go for wildfire s.
Sent from my HTC Wildfire using XDA App
showlyshah said:
As far as i know apn has nothing to do with ur network unless you enable/ use gprs/3g internet connection.apn means access point name, and so it have nothing to do with the calls or network.
Click to expand...
Click to collapse
Learned something new here
I would try the same as what howlyshah suggests: reflash your radio, without the whole blabla of RUU's.
You can try first the latest radio (ending with 20.10). If that doesn't work, you can try the one ending with 19.25.
The process is indeed not without risk, but so is s-off'ing and rooting your phone, and you did that already Just make sure that you have enough battery, you don't interrupt the process and be very patient (for example, it could be that the first boot takes longer than usual).
You can find the radio's in the wildfire index.
biteyou said:
Moreover, when I press down+power button, some sentences shown up:
SD cheking...
loading.. [PC49DIAG.zip]
no image!
loading.. [PC49DIAG.nbh]
no image or wrong image!
loading.. [[PC49img.zip]
no image!
loading.. [[PC49img.nbh]
no image!
after that it returned to the HBOOT menu and all become normal. They keep shown up no matter what RUU or CM7 rom I flashed. Is it a normal case or a sign of losing signal??
Click to expand...
Click to collapse
This is really really really normal. It is simply your bootloader searching for an update file. For example, if you are S-OFF and you rename an zip-file that you want to flash to PC49img.zip, the bootloader will automatically ask you if you want to flash that file (so no need to go into recovery). If you are S-ON, that will only work if the zip-file is signed by htc, of course.
Good luck!
ErwinP said:
Learned something new here
I would try the same as what howlyshah suggests: reflash your radio, without the whole blabla of RUU's.
You can try first the latest radio (ending with 20.10). If that doesn't work, you can try the one ending with 19.25.
The process is indeed not without risk, but so is s-off'ing and rooting your phone, and you did that already Just make sure that you have enough battery, you don't interrupt the process and be very patient (for example, it could be that the first boot takes longer than usual).
You can find the radio's in the wildfire index.
This is really really really normal. It is simply your bootloader searching for an update file. For example, if you are S-OFF and you rename an zip-file that you want to flash to PC49img.zip, the bootloader will automatically ask you if you want to flash that file (so no need to go into recovery). If you are S-ON, that will only work if the zip-file is signed by htc, of course.
Good luck!
Click to expand...
Click to collapse
Really thanks both of you! Finally I downgraded the CWM into v2.5.0.7 to flash the radio. I have flashed the radios ending with 20.10 and 19.25 and the problem still exists. Maybe it is the hardware problem.
showlyshah said:
As far as i know apn has nothing to do with ur network unless you enable/ use gprs/3g internet connection.apn means access point name, and so it have nothing to do with the calls or network. I think ur problem is with radio, as u have a3333 u can try flashing a new radio, and some ruu does not contains radio,if it is a moded one,so there are chances that u have used one of them, go for it , try a new radio.
And in worst case it is a hardware problem,in which ovclck had done some thing wrong with ur processor or the radio module(hardware).in that case dont try to get ur motherboard replaced by htc,since u r out of warranty it will cost u a lot, so buy a new phn, nxt time go for wildfire s.
Sent from my HTC Wildfire using XDA App
Click to expand...
Click to collapse
Thanks so much but I am a little bit confused by what you mentioned "out of warranty". Since I am still in the warranty period, is it still eligible if I flash the RUU froyo asia HK and flash the HBOOT 1.01.0002(S-on)? Or are you talking about the motherboard replacing service is out of warranty and they will charge me for the motherboard?
I am decided to buy a better phone now, I think it is a really good excuse Thank you guys!
Ya you have broken the security that htc implimented to protect their custom android os,which they use in wildfire,by s-offing ur phone.you can how ever fool them by flashing an ruu,and the s-on the drevice. I think there is some way to s-on the device.search the forum, u will find it, else flash an old ruu, like 2.1 or lower, connect to pc suite, update ur phn,and maybe htc will again update ur phone, and s-on it(i never tried it, but i think it will work,as most companies do the same like se,nokia etc), then you can get ur warranty back, save a bucket of buckz
Sent from my HTC Wildfire using XDA App
showlyshah said:
Ya you have broken the security that htc implimented to protect their custom android os,which they use in wildfire,by s-offing ur phone.you can how ever fool them by flashing an ruu,and the s-on the drevice. I think there is some way to s-on the device.search the forum, u will find it, else flash an old ruu, like 2.1 or lower, connect to pc suite, update ur phn,and maybe htc will again update ur phone, and s-on it(i never tried it, but i think it will work,as most companies do the same like se,nokia etc), then you can get ur warranty back, save a bucket of buckz
Sent from my HTC Wildfire using XDA App
Click to expand...
Click to collapse
The alpharev hboot has a version number 6.x The hboot from alpharev AND from htc are protected against downgrading: you can not install one with a version lower then 6 ATM. So flashing a RUU will NOT work.
Btw, we didn't broke the security, the phone is still S-ON. But the hboot thinks it's S-OFF.
However, I tought I've read somewhere here on the wildfire section a way to downgrade the alpharev hboot to a htc one. So you can take a look indeed.
Erwin
EDIT: I've just read this in an other toppic:
rashmifantasy said:
For maybe some more like me that want to go back to what it use to be with the hboot S-OFF, S-ON issue.
I had my phone S-OFF with alpharevx beta. Used CM7 -stable for couple days but decided i wanted to go back to all original. I first RUU my phone with the RUU_Buzz_Froyo_HTC_WWE_2.22.405.1_Radio_13.55.55.2 4H_3.35.20.10_release_160191_signed.exe file. Boot it up, made sured it runs, then did what is instructed below here;
To be able to do this you need HTC USB drivers installed. Install the HTC pakage, reboot, uninstall the HTC-
Sync software, keep the drivers! reboot PC again.
Power off your phone. Plug in your USB cable to phone. Press volume down and powerup your phone. After it
settle navigate down and choose fastboot option.
1. Unpack these files to your c:\fastboot
2. Open up your windows command promt (WinVista/7 users rightclick choose run as Administrator)
3. in command promt type CD\ then press enter
4. then your should be in C:\
5. type cd fastboot
6. then you should now be in dir C:\fastboot
7. Im bored to death typing, look below. Beware of each command ends with enter. After success, reboot.
C:\fastboot>fastboot oem mb 9C068490 1 30
... OKAY
C:\fastboot>fastboot flash hboot hboot_buzz_7225_1.01.0001.nb0
sending 'hboot' (512 KB)... OKAY
writing 'hboot'... OKAY
Files needed (Windows version): megaupload.com/?d=UO9L74I9
Works perfectly for me.
* NOTE: Im not responsible for your phone if you brick/kill it. These steps worked for me!
Click to expand...
Click to collapse
Thanks to all of you! All of your suggestions are useful and I finally got my wildfire S-on(fastboot: flash into Hboot1.01.0001, then flash RUU and become Hboot 1.01.0002) and sent to HTC for repairing. Finally they replaced the main board and it now works perfectly.
I am so scared my device will be broken again, so I want to seek a full guide here before I S-off, root and flash a new ROM again because of some bug of the stock ROM.
Q.1
Sometimes when I receive a call, I cannot unlock the lock screen, seems the touch screen is not working while ringing. Every time I encounter this problem, I have to reply the call after the the device stop ringing. It is really troublesome for me. Is flashing another ROM the only solution for solving this problem? any ROM suggestion for this problem??
Q.2
Before I sent the phone to repair, the Hboot 1.01.0002will check for update:
(SD cheking...
loading.. [PC49DIAG.zip]
no image!
etc..)However after HTC sent me back the repaired phone I found that the Hboot now do not search for the update anymore. In case I break the phone again by S-off, rooting andflashing a new rom, I need to S-on the phone again. But I am quite sure that If I S-on the phone again, the resulting Hboot will search for update and therefore different from the original Hboot after the phone repaired.
My question is: Is this device in the warranty in this case?
Q.3
I am also looking for a ROM supporting APP2SD/APP2EXT/Dalvik-Cache2SD/DATA2SD/DATA2EXT system (I am quite confused with the difference between them even after googled, can anyone tell me that?), any suggestion of the ROM supporting it?
I have used Darktremor before my phone broke for the app2sd but It is quite difficult to use since it involves inputing some command in the terminal emulator (and so scared to break the phone again by this). Actually it is very good, but I prefer some user-friendly apps that can perform the APP2SD/APP2EXT/Dalvik-Cache2SD/DATA2SD/DATA2EXT system.
I found some apps, for example, simple2ext(S2E) and link2SD but I dunno the pros and cons between them.
My question is, which system moving apps into sd card is most suitable for wildfire??
Thanks for your help!!
Related
So i hope this is the right place to ask. I updated the radio to 6.xx and the spl to 1.33.0013 and now i cant boot my custom rom or access the recovery screen, but i can access fastboot. Ive tryed flashing a new radio, recovery etc from the sdk cmd promt and no luck, keeps saying remote: not allow. IS there anything i can do from the fastboot to get my phone back. Sorry if this is realy noobish. Ive searched for 3 days and i've had no luck. PLEASE HELP ME
Sapphire pvt 32a sip s-on g
hboot-1.33.0013 (sapp31000)
CPLD-13
Radio-6.35.10.18
oct 21 2009,22:33:27
You are ok untill now..You have not bricked your phone....you can still recover it using fast boot or recovery...
serach for the correct topic on this fourm...you will surely get info
Ive tryed everything in fastboot and i cant get into recovery. If i could i would have fixed it by now
Tried Goldcard method as well?
I cant do a goldcard again. I cant access the operating system. I cant access the recovery screen. Al i can do is access fastboot. And from there i just get remote: not allow when i try to modify things. I just need a BIG reset button on this phone. Im hitting my head so hard against the wall trying to figure this out. I try to read up but everywhere you go its something different and its all soooooooo confusing. No one makes nay sense
If this is a bad place to ask this, please tell me. My head hurts and im very frustrated because i followed someones write up step by step and i got screwed over. I know it can be fixed!
OK dude, just breathe. By looking at your SPL you've got the myTouch 1.2 (the one with the 3.5mm jack) so you've got o use the goldcard method which is done through hboot and fastboot, if you can get one you can get the other. Let me get to a computer and we'll fix your problem. In the mean time post back and let me know your still here.
Sent from my HTC Magic using XDA App
You need to fastboot an engineering spl first.
I believe 1.33.2010 should do it.
Flash back to the operator's ROM and start all over again; safest approach if you are having a difficult time understanding how to troublshoot your problem.
I try to load a new sippimg.img ( from my understanding that a new spl) And everytime i load it, it says model id wrong and fails to load.
And in fast boot i cant load anything new cause i get the remote: not allow.
How am i suppose to create a gold card another gold card without having access to the phones main operating system?
I just went to http://forum.xda-developers.com/showthread.php?t=529019 and followed that and wasnt able to load the recovery image cause because remote: not allow. So im stuck
Try using this.
Sent from my HTC Magic using XDA App
I cant create a new gold card, i cant access the phone I created one before but it still gives me a the wrong mode ID code. And i cant do adb because i cant turn on USB debugging since i cant access the phone.
I followed the steps in the link. I loaded the sappimg.img and it loaded it but didnt ask to confirm the install, but it did show a loading bar and when it was completed it never said anything about restarting or anything. It just detected it, loaded it and then nothing. So after that i tryed to load the spl, radio and recovery and it still gave me remote: not allow.
It seems my gold card somehow undid its self. I need to figure out how to make one without being able to access the actual phone options. I realy do appreciate you guys helping!!!! If this gets fixed ill kiss all of you. JK!
How long have you had your phone?
3 days But i didnt buy through t-mobile, so no warranty for me
The only other option I can think of is to see if a friend with the same phone can let you borrow his. Luckily the stuff you need to do isn't phone specific, it's only specific to the SD card, so you can remake it with another phone and then use it to finish your's.
I believe the CID that you get (that ridiculously long number you have to copy) is specific to the SD card. I just swapped the goldcard I made for my phone into my wife's and the CID remained the same. Just not sure if using a different model phone will work.
You don't happen to have the CID still do you?
DonJuan692006 said:
The only other option I can think of is to see if a friend with the same phone can let you borrow his. Luckily the stuff you need to do isn't phone specific, it's only specific to the SD card, so you can remake it with another phone and then use it to finish your's.
I believe the CID that you get (that ridiculously long number you have to copy) is specific to the SD card. I just swapped the goldcard I made for my phone into my wife's and the CID remained the same. Just not sure if using a different model phone will work.
You don't happen to have the CID still do you?
Click to expand...
Click to collapse
I still have all the emails for when i originally made a gold card and the goldcard.img.
You can try doing the steps in Hex Editor, where you copy the lines from the goldcard image over to your SD card again. Then try flashing the sappimg again and see what you get.
On it! :cross fingers:
I did all the Hex editor stuff. And i still get Wong model ID when i try to install a new sappimg.img. I tried several times and double checked the hex editor.
I have a basic question,
I'm only asking because there's far too much
information available,
on here
and its not easy to find what best fits my
needs.
I have an unlocked A3335 wildfire ( Telstra NextG network 3g version), I'm using it on optus,
my boyfriend was useing it he dowloaded a
font change app for the phone,
but when he did it my phone went in to
bootloop mode.and keep't bootlooping again
and again
all i get is the start up screen,
with yes you guessed it
(Telstra NextG network 3g crap)
All I want to do is try and get my phone from
this bootloop mode and try and recover...
my phone back to how it was.
Its hard to explain,
ok when i go in to the boot screen
i have this on my phone
BUZZ PVT SHIP S- Off
HBOOT-1.01.0002
MICROP-0622
TOUCH PANEL-ATMEL224_16ab
RADIO-3.35.20.10
DEC 27 2010,
17:49:10
and it reads the sd card,
it said the Boot Image. is missing
dont know why a app would take this out
but this is what happen
So Now when i did the fastboot on my phone
it done nothing,
then did the clear storge.
then i did the recovery
it rebooted to a black screen with A
triangle shape with one of these things
! in the middle of it,
but still stuck
I can follow the regular guides for rooting,
can any one help me to get my phone back to
how it was please
And I really don't care about this part much,
but would be nice to have it off the phone
and remove all the telstra junk and restore
the phone back to how HTC would ship it,
(all the junk apps they include could easily be optionally installed from marketplace if you want their crap...)
(obviously I'm in Australia also)
There are so many ROMS and options available,
including the ones from shipped roms
(it wont let me post the link because I'm new).
I just want my phone back to how i got it,
can any one help me please....
please send me a private messages,
with a step by step guide to do so thanks..
Since you are s-off u can use fastboot flash from windows to flash a clockwork mod recovery. After you do that, every thing will be simple. Just download a rom in zip format,put it to sd go to recovery( just do what you have done to see the triangle in blackscreen. Note that if u flash cwm you will no longer see that triangle). Then use your volume down button to reach install zip from SD card. Hit it with joystick press. Choose zip. Install it. Just do a data- factory resetting before you install zip.
I prefer cyanogen mod 7. U may use latest stable or nightly build. Feel free to post any doubt you have. We are happy to help you.
Regards shah.
Sent from my HTC Wildfire using XDA App
thank you so much your a life saver it work't have my phone back now yay
K. Be in touch with xda. Find out more. Make your wildfire yours and not htc's.
Thank u
Sent from my HTC Wildfire using XDA App
well i got some bad news its gone back to how it was,
trying to do the same thing,
could you please give me a step by step guide thanks,
do i need to turn my sd card in to a gold card ?
its formatted to a FAT32
If you have any ideas where to go and get this would be a great help
aussiegirl said:
well i got some bad news its gone back to how it was,
trying to do the same thing,
could you please give me a step by step guide thanks,
do i need to turn my sd card in to a gold card ?
its formatted to a FAT32
If you have any ideas where to go and get this would be a great help
Click to expand...
Click to collapse
nope that gold card image will send to ur email..and u need to copy that gold card image to ur sd card...
Well if the hboot is 1.01.0002 with S-OFF then it must be done using xtc clip. So fastboot flashing shouldn't be working. And u don't need a gold card for S-OFF wildfire .
I would just suggest to flash a stock froyo WWE RUU which also removes the carrier bloatware. If ruu proccess gives errors u can copy the romzip from that ruu and use it with pc49img process from hboot menu. And ofcourse fat32 memory card is must for pc49img process
Sent from my Blade using XDA App
Hey can you explain what happened now? You said that yours is working now before 2 days. ( in second last post). So what happened now? What have you tried with your phone?
And...
So the gold card question, let me explain.
Gold card is just a patch tool, with the help of which you can unlock HTC boot loader , or in detail, you can unlock HTC 's boot loader protection(that's what we call as s-off) , which is commenly locked( that's we call as s-on) , for a user mode phone( a phone that is for sale to normal user), and it is done so because a normal user never need a root permission, over clocking etc. Also user defined kernal,rom,radio updates unless HTC provide them with updates.( and of cource to protect their device and its custom os made by HTC.
So being an s-off device, we can say in simple, unleash the potential of android.( that's what i said, make the device yours and not HTC 's).
And s-off. In can be done using many ways, find them in topic " complete wildfire index " , one of which is using goldcard method. It is also explained in topic/ stickies " downgrade hboot to xxxx". You can download an attached file called buzz downgrade from that topic, and its what you all need.
And about ruu flashing, i think its not a safe one for you, Coz your phone is a3335? Right? If so, original ruu flashing may cause problems with network( called as radio problems), so you can use custom/ safe ruu, instead. Which contains no radio image, check " complete wildfire index" else go for custom os like cm7.
But before all you should mention what you need.
1) r u trying to put custom os, or do you need original os?
2) do you want your phone to be a true android gadget, or just normal phone which is provided by HTC?
3) what kind of user r u? Normal user or a tech junky?
4) r u satisfied with android 2.2 or need 2.3?
Get us the answers, along with your current boot menu( where you find recovery option) details. So that we can help you properly.
That's all dude. Its 2.30 am here in India, so i should wish myself a good night, swtdrmz. Cu ltr.
Sent from my HTC Wildfire using XDA App
showlyshah said:
And about ruu flashing, i think its not a safe one for you, Coz your phone is a3335? Right? If so, original ruu flashing may cause problems with network( called as radio problems)
Click to expand...
Click to collapse
Oops. Completely missed that point, sorry.
But since the phone is S-OFF one can just flash the system.img and boot.img alone from wwe ruu to remove the carrier bloat and to continue on the HTC stock rom (only if u wish to). Same pc49img process here but with only system.img and boot.img along with android-info.txt .
Sent from my Blade using XDA App
bharatgaddameedi said:
Oops. Completely missed that point, sorry.
But since the phone is S-OFF one can just flash the system.img and boot.img alone from wwe ruu to remove the carrier bloat and to continue on the HTC stock rom (only if u wish to). Same pc49img process here but with only system.img and boot.img along with android-info.txt .
Sent from my Blade using XDA App
Click to expand...
Click to collapse
now im lost where do i fine the right one to use do you know how many there are out there this phone is doing my head in i try to flash the system.img and the boot.img and a stock rom and still nothing im ready to give up to be honest
Have you installed clockwork mod recovery? If not do it first. Use fastboot flash from windows or linux, then download latest cyanogen mod nightly and put it in your sd. Then use install zip option from cwm recovery to install cm7. Done. Its what you want. No radio harm will be done unless you flash a radio using any methods.
All info will be available on thread" complete wild fire index" in this forum. Tools, recovery, how to, rom, and every thing else are available in that thread.
Sent from my HTC Wildfire using XDA App
i have all of these things you said here what i dont understand i have tryed this so many times and still dosent work and its abit hard with work as i dont get much time to fix this phone for the past week has given me nothing but a pain in the rear end and its doing my head in...
ok let me show you and try to explain this ok i rooted my phone before so you know its s-off what im trying to do is to get it from the boot looping as its stuck until i put it in to HBoot and did a recovery it stop boot lopping then i did a search and come across this site read and read countless info trying a number of things first so then i did the clear storage then rebooted phone then i got the home screen with yes the Telstra NextG network then i took out the battery then put it back in did the same thing as before got in to HBoot then i read on here to turn the sd card to a fat32 which i did so i read more and more did that they said to do and so on now when i did that i got the home screen with Telstra NextG network then it changed to a black screen with a yes triangle shape with one of these things ! in the middle of it, so then i come here post this on here looking for help then i did what you said to do it work for 2 days then went straight back to how it was then i read the reply's to this done the same thing'y over and over still im with out my damn HTC hunk of junk to be honest this phone has become a big pain in the rear end and has done my head in for over a week i rooted a LG p350 and that hasn't been unlocked until i did it i have never in my life had so much drama with a HTC WILDFIRE A3335 until now i did all my mates smart-phones with no hic up now trying to do my own its like im at the end of my wits i have photos with this so you can see what i get when doing what you said ok the gold card thing'y already did it still phone will not read it as you will see first hand
aussiegirl said:
ok let me show you and try to explain this ok i rooted my phone before so you know its s-off what im trying to do is to get it from the boot looping as its stuck until i put it in to HBoot and did a recovery it stop boot lopping then i did a search and come across this site read and read countless info trying a number of things first so then i did the clear storage then rebooted phone then i got the home screen with yes the Telstra NextG network then i took out the battery then put it back in did the same thing as before got in to HBoot then i read on here to turn the sd card to a fat32 which i did so i read more and more did that they said to do and so on now when i did that i got the home screen with Telstra NextG network then it changed to a black screen with a yes triangle shape with one of these things ! in the middle of it, so then i come here post this on here looking for help then i did what you said to do it work for 2 days then went straight back to how it was then i read the reply's to this done the same thing'y over and over still im with out my damn HTC hunk of junk to be honest this phone has become a big pain in the rear end and has done my head in for over a week i rooted a LG p350 and that hasn't been unlocked until i did it i have never in my life had so much drama with a HTC WILDFIRE A3335 until now i did all my mates smart-phones with no hic up now trying to do my own its like im at the end of my wits i have photos with this so you can see what i get when doing what you said ok the gold card thing'y already did it still phone will not read it as you will see first hand
Click to expand...
Click to collapse
No expert but looks like you have an empty sdcard and system.I think you need to get a rom onto your sdcard (cm7 good choice) and then through recovery apply the rom. Zip and reboot after. DONT DO A WIPE.the telestra screen is just a splash screen which will always load before the system searches for data to load,next would be boot loading screen but yours by the looks and sounds of things does not achieve!! Probably cos its not present due to not having a rom installed.hope I helped if not best of luck. Members are very helpful here and cos you can access hboot I am 99% sure this will be fixed for you. Regards Slymobi.
Sent from my HTC Wildfire using XDA App
i have a rom on my sd card but the thing keeps saying FAILED? NO SUCH FILE FOUND ?
Download this: http://shipped-roms.com/download.ph...5.55.24H_3.35.20.10_release_160191_signed.exe
Enter HBOOT.
Wait until it finishes trying to load a zip file.
Choose FASTBOOT to enter FASTBOOT USB mode.
Run the downloaded file.
It should then install the original HTC rom.
Or maybe try PC49IMG method if you haven't already?
On your PC click start and type in the search box %temp%,
Keep your eye on this folder and doubleclick your ruu, a new folder should appear in temp folder,
Open it and search for rom.zip,
Copy it to your desktop and rename it to PC49IMG.zip then copy to your SD card and boot into hboot, it should find the zip and install.
Sent from my HTC Wildfire using xda premium
@scratches post. I couldn't remember the method but that's exactly how I got my ruu to install so I could revolutionize.
Sent from my HTC Wildfire using XDA App
i have done that already still no go
Hi , okay i lost my old MyTouch 4g from launch , and received a new one back in August. I decided to finally do the downgrade via ADB , i got through every step and when it was time to do the "manual Downgrade" i put the Rom on the root of the SD card and when i booted to the bootloader it said PD15IMG.zip was found but the nbh file wasn't found
SD Checking...
Loading... PD15DIAG.zip
No image!
Loading... PD15DIAG.nbh
No image or wrong image!
Loading... PD15IMG.zip
No image!
Loading... PD15IMG.nbh
No image or wrong image!
and it never performed a downgrade , now when i tried to reboot back to the current rom, it gets stuck at the MYtouch 4g sign
i have a G1, so im able to swap memory cards to move files if need be because im not sure if i could access the USB mass storage through the bootloader
More information i have is at the Bootloader is
GLACIER PVT SHIP S-ON
HBOOT-0.89.0005
MICROP-0429
RADIO-26.11.04.03_M
eMMC-boot
If I see and you type what there really is, then it didn't find any PD15IMG.ZIP.
That would be either because you have your card formatted in some weird way, or because you didn't follow the guide, didn't read the multiple warnings and unknowingly named your file PD15IMG.ZIP.ZIP (because your Windows isn't set to show file extensions).
So, formatting the SD card before use with regular FAT32 and making sure the name is right will solve that.
Moreover, you should check the MD5 of the PD15IMG. It will keep looking for .nbh only if the file is wrong.
no i downloaded the PD15IMG zip file from the guide i didn't have to change anything it was already named that file, so if i format the memory card all should be good ?, would i have to worry about doing the ADB again because i had multiple reboots by taking out the battery because of being stuck at the splash screen.
EDIT: Thank You Progress was made i just Formatted the memory Card now, its performing the Update through the Bootloader to 2.2.1 with the blue side bar , i'll keep this posted with another Edit
EDIT: 2.2.1 update wasunsuccessful it getts stuck at the purple "updating" words i went to a youtube video to see what the update process would be like its supposed to go "updating, OK, OK, Unzipping"
imma try to reinstall 2.3.4 then doing the ADB method if possible
EDIT: updating to 2.3.4 does nothing but the same thing 2.2.1 update did , now im stuck scratching my head
It means that the phone is stuck updating one of the partitions, which is bad.
You could attempt to flash Panache RUU on this thing. HTC have their own downloader, inaccessible through regular modes, which is invoked when RUU is being flashed using EXE file. You might also need a goldcard for your phone to attempt it. In the Mobilicity/Panache rooting thread in General section you'll see all the info on creating a goldcard. A bit of search will get you the Panache RUU .exe file
If the RUU is successful - you'll have HTC Panache for a phone. From there, you can attempt rooting and downgrading instructions in the Panache rooting thread.
If you still have warranty - I'd use it. Flashing Panache RUU, if it won't get you luckier with PD15IMG, will be irreversible, since I don't know of MyTouch 4G RUU in .exe format.
alright i have all the necessary files such as the RUU exes i tried to make the gold card but was unable to do so using the simple Gold card method , how would i go about turning my phone into the Panache if my phone cant even turn on fully ?
HTC software running on PC doesn't need your phone to be booted, it can automatically put the phone into HTC-specific download mode from any other mode.
Run the RUU.exe while the phone is in the bootloader, for example, and see if it flashes, and if not - what error does it show.
the RUU.exe says USB error, everytime i plug my phone in through the bootloader the computer comes up with a Android 1.0 New Hardware wizard i dont know if this is interfering with the .Exe not finding the phone
EDIT: Found Android 1.0 drivers , now the error was the phone not being charged LOL! , ill keep this posted with another edit after the phone is charged, thank you for the help i appreciate it.
Yes, you'll need the driver operational.
Use Windows 7 computer, it'll automatically find and install the needed driver.
Thank You So Much for your Help i went to T-Mobile , and my insurance covered for a new phone i took the option of going for the Sensation instead of getting another Mytouch 4g and running into the same problem,
I Enjoyed this community from my First MyTouch 4g of flashing multiple ROMS , this was and is a powerful phone i wish it had more dev/hacker support with this phone
Hi!, I've a not rooted HTC Desire Z.
After being very slow for some day today the device stay on the white screen with HTC for hours.
I've then tried to factory reset the device but when i select factory reset it stay stuck on the menu voice and i've to reboot removing the battery.
If i choose recovery it shows a green circle and an arrow in the center.
I've searched a bit on the forum but who has the same problem has not my model of phone and who has the same model has already unlocked the bootloder.. so... could anyone show me the right image/process to take to unlock/format the phone?
Put the og pc10 image for your phone and flash through flashboot. Start over. You're hanging cause your not rooted
Sent from my SGH-T989 using xda premium
where can i download this pc10 image?
---
in the meantime i've searched in the forum looking for this image... i've found two files i think that the good one is the one that end with "signed"
PC10IMG_Vision_TMOUS_1.19.531.1_Radio_12.21.60.09b_26.02.01.15_M2_release_149459_signed.zip
it need to be renamed in PC10IMG.zip ?
in meantime:
I've tried
putting the image with the firs and the second name but it stay in the same stuck white screen...
ok figured it going in bootloader mode with the file in the flash... but i can't find the original PC10IMG.zip to use.
I'm really lost in all the topics... please help
koma85 said:
where can i download this pc10 image?
---
in the meantime i've searched in the forum looking for this image... i've found two files i think that the good one is the one that end with "signed"
PC10IMG_Vision_TMOUS_1.19.531.1_Radio_12.21.60.09b_26.02.01.15_M2_release_149459_signed.zip
it need to be renamed in PC10IMG.zip ?
in meantime:
I've tried
putting the image with the firs and the second name but it stay in the same stuck white screen...
ok figured it going in bootloader mode with the file in the flash... but i can't find the original PC10IMG.zip to use.
I'm really lost in all the topics... please help
Click to expand...
Click to collapse
Uhh uhh uhh... until someone like niqper (or however you spell his name) comes in here and tells you to flash that PC10IMG, do NOT flash it, I'm not saying it will break your phone but considering you aren't rooted I'm thinking it's not at all necessary and I don't know the consequences.. So wait, can you access the bootloader by holding down + vol ? What happens exactly?
noneabove said:
Uhh uhh uhh... until someone like niqper (or however you spell his name) comes in here and tells you to flash that PC10IMG, do NOT flash it, I'm not saying it will break your phone but considering you aren't rooted I'm thinking it's not at all necessary and I don't know the consequences.. So wait, can you access the bootloader by holding down + vol ? What happens exactly?
Click to expand...
Click to collapse
Hi! and thank you for your interess:
The phone is unbranded and not rooted.
It's impossible to boot normally
And selecting the recovery or the factory reset just freeze on the bootloader screen.
I've tried putting the PC10IMG.zip that I've found on the web but seems that I need a later version because all the version I've used are too old.
Code:
VISION PVT SHIP S-ON
HBOOT-0.85.0013
MICROP-0425
RADIO-26.10.04.03_M
eMMC-boot
Apr 11 2011,23:36:27
Try creating a gold card, you'll find how to guides all over the web
Sent from my HTC Vision using xda premium
Here is the RUU for your phone RUU_Vision_Gingerbread_S_HTC_WWE_2.42.405.2_Radio_12.56.60.25_26.10.04.03_M_release_199043_signed.exe
You can try just running the exe, or extracting the zip from it (run it, until it loads (says press next or whatever) and go to the %temp% dir in windows, and do a search for rom.zip, should be roughly 250mb)
It will be safe to flash, but will wipe all your data.
I do have a suspicion that you have a fried emmc chip, you seem to have some of the symptoms, so if it hangs during the flash that will be why, in which case you can't fix it and will need to get a replacement.
-Nipqer
Nipqer said:
Here is the RUU for your phone
You can try just running the exe, or extracting the zip from it (run it, until it loads (says press next or whatever) and go to the %temp% dir in windows, and do a search for rom.zip, should be roughly 250mb)
It will be safe to flash, but will wipe all your data.
I do have a suspicion that you have a fried emmc chip, you seem to have some of the symptoms, so if it hangs during the flash that will be why, in which case you can't fix it and will need to get a replacement.
-Nipqer
Click to expand...
Click to collapse
Thank you, I've extracted the rom.zip and uploaded it on the SD.
The process starts updating but hangs on the first step (updating bootloader).
I think that you are right the emmc is gone...
koma85 said:
Thank you, I've extracted the rom.zip and uploaded it on the SD.
The process starts updating but hangs on the first step (updating bootloader).
I think that you are right the emmc is gone...
Click to expand...
Click to collapse
That's a real shame time to upgrade to SGS3 or One X ? I think sooo! I'm so glad we have a resident expert like niqper to help us out with general technical stuff though so when I make the change I'll definitely miss that !
Sent from my HTC Vision using XDA
noneabove said:
That's a real shame time to upgrade to SGS3 or One X ? I think sooo! I'm so glad we have a resident expert like niqper to help us out with general technical stuff though so when I make the change I'll definitely miss that !
Sent from my HTC Vision using XDA
Click to expand...
Click to collapse
I've sent the phone in repair. I'll update with new infos
Here is the RUU for your phone RUU_Vision_Gingerbread_S_HTC_WWE_2.42.405.2_Radio_ 12.56.60.25_26.10.04.03_M_release_199043_signed.ex e
You can try just running the exe, or extracting the zip from it (run it, until it loads (says press next or whatever) and go to the %temp% dir in windows, and do a search for rom.zip, should be roughly 250mb)
It will be safe to flash, but will wipe all your data.
My boot screen says:
Vision PVT ship s-on
HBoot 0.85.0013
Microp-0425
radio-26.10.04.03_m
eMMC-boot
Before it read:
Vision PVT Eng s-off
HBOOT-0.76.2000
MICROP-0425
RADIO-26.03.02.26_M
Its an HTC G2 but has the same problem with being stuck on the HTC screen
Is there an ruu for my phone? I tried the one above and it started fine, updated the first 2 then reset then when it reloaded it says "model ID incorrect"
You shouldn't of flashed that rom, thats for a DZ, not a G2.
You must've had fake S-OFF too.
You can try flashing this rom PC10IMG_Vision_TMOUS_2.15.531.3_Radio_12.52.60.25U_26.08.04.30_M3.zip
You better hope your main version is low enough to accept it though.
And that the DZ hboot accepts it (chances are it'll throw some sort of heap error)
You might be able to use a goldcard (which you need a functioning android phone to create) to allow the DZ stock rom to flash, though I can't guarantee anything.
Your phone not booting would be because the g2 hboot and dz hboot have their partition layout quite different, so its looking in the wrong place to try load android now.
-Nipqer
Hi guys,
I've tried many ways to fix and hope that some light could be shed from you
- Trying to get back to stock build after downgrading to 1.31 via this process wiki.cyanogenmod.com/wiki/HTC_Legend:_Full_Update_Guide
- The ‘rooting tools’ in step 2 of 2nd section were not available anywhere so tried other avenues to root
- None successful
- After lots of playing around – I decided to try and get back to latest stock build
- Ran the uncracking.bat file which was installed during the Cyanogenmod process (which I hoped would restore things)
- Not successful
- I’m thinking that maybe the adb shell command from the Cyanogenmod process may have caused some issue: /data/local/flash_image misc /data/local/misc1-2.img
- Trying the HTC OTA system update (from Android 2.1 to 2.2) fails while trying to update and goes into the recovery screen (red triangle with exclamation mark, black background) <<<<<<<<<
- Then, when pushing vol up and power the following error is shown:-
----> E:Error in /sdcard/download/OTA_Legend_Froyo_S_HTC_WWE_3.15.405.3-2.05.405.2_P_release_1603576x6ndkkwfpxcjvla.zip (Status 7) Installation aborted.
Any help would be greatly appreciated..
Doing a general factory reset does not seem to help.
I do not need to keep any apps or data, a complete wipe so I can start afresh would be great if possible!
Thanks
94 views and no replies.
Oh dear
I tried to return to stock rom by running the wwe rom from shipped-roms only got the error 155. Then extracted the rom.zip from the exe and flash that no go, couldn't work out a way to do it successfully.
Sent from my Legend using xda app-developers app
Cool.. It doesn't have to be stock. All I need is 2.2 or 2.3 (I was trying for cyanogenmod 7.2). At the moment it's stuck on a buggy 2.1!
I'm not sure of the current state, as I said I think going half way through the cyanogenmod kinda of changed something important ( eg. /data/local/flash_image misc /data/local/misc1-2.img via ADB).
Do you know of any way I could make either of these OSs work, with the minimum of hassle?
ranger4740 said:
I tried to return to stock rom by running the wwe rom from shipped-roms only got the error 155. Then extracted the rom.zip from the exe and flash that no go, couldn't work out a way to do it successfully.
Sent from my Legend using xda app-developers app
Click to expand...
Click to collapse
1st thing 1st, unlock your bootloader.
2ndly, once unlocked, flash cwm.
3rd, download any ROM you want (lets pick cm 7.2 for starting point since you said no need for stock ROM) then put into your sd card.
Lastly, boot into cwm. Wipe all (data, cache, dalvik cache) then Flash(install) ROM.
Thats it (assuming your device is not usb bricked or hard bricked and you do all the steps correctly).
How?
To unlock, go to htc web site or google "unlock bootloader+htc dev"
Flash cwm? Go to dev section, theres a thread of cwm, follow "s-off" method (of course after unlocking your BL.
Boot into cwm? Shut down/turn off your phone. Once it off, press power button and volume down at the same time, hold it fow few moment before release it.
Once in cwm, install from sd card (you will know once you in it)
Then? Enjoy ur legend and flash any ROM once you got bored with cm7!
Sent from my Legend using xda app-developers app
Thanks for the response.
Firstly: -
- HTC Sync is not reading my (I think needed for HTCDev boot unlock)
- I did try just running the HTC Dev RUU - but it said I need to update the ROM(?) (from Build 1.31), which I believe is done by the HTC OTA update, which doesn't work
HBOOT 1.00
S-ON
Build 1.31
Not allowing update as loops into recovery with E:Error in /sdcard/download/OTA_Legend_Froyo_S_HTC_WWE_3.15.405.3-2.05.405.2_P_release_1603576x6ndkkwfpxcjvla.zip (Status 7) Installation aborted.
feed3 said:
1st thing 1st, unlock your bootloader.
2ndly, once unlocked, flash cwm.
3rd, download any ROM you want (lets pick cm 7.2 for starting point since you said no need for stock ROM) then put into your sd card.
Lastly, boot into cwm. Wipe all (data, cache, dalvik cache) then Flash(install) ROM.
Thats it (assuming your device is not usb bricked or hard bricked and you do all the steps correctly).
How?
To unlock, go to htc web site or google "unlock bootloader+htc dev"
Flash cwm? Go to dev section, theres a thread of cwm, follow "s-off" method (of course after unlocking your BL.
Boot into cwm? Shut down/turn off your phone. Once it off, press power button and volume down at the same time, hold it fow few moment before release it.
Once in cwm, install from sd card (you will know once you in it)
Then? Enjoy ur legend and flash any ROM once you got bored with cm7!
Sent from my Legend using xda app-developers app
Click to expand...
Click to collapse
Curveau said:
Thanks for the response.
Firstly: -
- HTC Sync is not reading my (I think needed for HTCDev boot unlock)
- I did try just running the HTC Dev RUU - but it said I need to update the ROM(?) (from Build 1.31), which I believe is done by the HTC OTA update, which doesn't work
HBOOT 1.00
S-ON
Build 1.31
Not allowing update as loops into recovery with E:Error in /sdcard/download/OTA_Legend_Froyo_S_HTC_WWE_3.15.405.3-2.05.405.2_P_release_1603576x6ndkkwfpxcjvla.zip (Status 7) Installation aborted.
Click to expand...
Click to collapse
No, you dont need htc sync. i've never installed htc sync either. you only need the driver (which is logically will be installed along with htc sync but also can be installed separately and it is needed so that your device will be recognized when you boot it into fastboot mode) and no, you no need to upgrade ROM, you only need to upgrade your bootloader (that HBOOT 1.00) and it is not updated through OTA.
Seriously, it took me only 2 hours (including downloading and installing SDK, driver, waiting for unlock file from htc etc) last time i did it and i have done it twice which 2nd time (because i had usb soft brick) is much more shorter as i saved the unlock file and it seems can be reused. What takes longer for me at that time is to understand the whole process, reading and researching through multiple sites but now you have a guide, so all you have to do is to read the instructions carefully. Once you unlock your bootloader and flash cwm, everything will be super easy (assuming your device doesn't have any defects from the beginning.)
Ok, thanks very much feed3. Will try this again based your info and the mini guide I've just written myself.
But before I go ahead, I'd rather not touch it than to make it unusable.
What does USB Bricked and Hard Bricked mean?
Thanks
----------------------------------
My guide:-
After reading the latest reply at XDA decided to give the root another go:-
http://forum.xda-developers.com/showthread.php?p=29969951#post29969951
- Seems need to upgrade HBOOT (to use the HTC Dev boot unlocker)
o See here post 62 and poss (BEFORE THIS READ NEXT BIT) 74 http://forum.xda-developers.com/showthread.php?t=1498298&page=7
- READ HERE FIRST Looks like other people have had issues using stock Vodaphone 2gb SD card for goldcard. Get another and try. Go post that states ‘EDIT: It seems the LEGEIMG is not getting loaded’ that and the few posts after explain what’s happening. http://forums.whirlpool.net.au/archive/1657826
- So neeed to have a gold card in to make the above work <<
o Looks like this can do an auto gold card for you https://sites.google.com/site/roothtchero/goldcard-2. Remember to format to FAT32 in windows as opposed to phone. SEE Hubdolt POST WHICH TALKS ABOUT FORMATTING VIA THE CMD LINE (FOR VODAPHONE LEGEND)
Curveau said:
Ok, thanks very much feed3. Will try this again based your info and the mini guide I've just written myself.
But before I go ahead, I'd rather not touch it than to make it unusable.
What does USB Bricked and Hard Bricked mean?
Thanks
----------------------------------
My guide:-
After reading the latest reply at XDA decided to give the root another go:-
http://forum.xda-developers.com/showthread.php?p=29969951#post29969951
- Seems need to upgrade HBOOT (to use the HTC Dev boot unlocker)
o See here post 62 and poss (BEFORE THIS READ NEXT BIT) 74 http://forum.xda-developers.com/showthread.php?t=1498298&page=7
- READ HERE FIRST Looks like other people have had issues using stock Vodaphone 2gb SD card for goldcard. Get another and try. Go post that states ‘EDIT: It seems the LEGEIMG is not getting loaded’ that and the few posts after explain what’s happening. http://forums.whirlpool.net.au/archive/1657826
- So neeed to have a gold card in to make the above work <<
o Looks like this can do an auto gold card for you https://sites.google.com/site/roothtchero/goldcard-2. Remember to format to FAT32 in windows as opposed to phone. SEE Hubdolt POST WHICH TALKS ABOUT FORMATTING VIA THE CMD LINE (FOR VODAPHONE LEGEND)
Click to expand...
Click to collapse
in short, hard bricked means your phone is totally unuseable, usually because of hardware defects but also might be cause by flashing wrong ROM, for example flashing ROM that actually not built for your device. Usually, you cannot do anything with it, cannot enter fastboot, recovery etc. Soft brick is repairable, you still can boot to recovery or even to the OS. Might be caused by some partition corruption (in the case of usb bricked, it is /misc partition).
If you use htc dev path to unlock your bootloader, no need for gold card. Thats for sure.
If your phone is usb soft bricked (among the symptoms are you will be able to boot into the OS ONLY if your phone are pluged in into usb, and/or adb not working at all) then google or search in xda for "htc legend+usb brick" and fix it. I'm pretty sure only then you can update your HBOOT and therefore unlock your bootloader via htc dev.
Once done, go to HERE and flash cwm using s-off method (dont care about your s-on that you see in your bootloader, the "UNLOCKED" word in it is more important)
In response:-
Thanks for the clarification.
- when using the process here http://forum.xda-developers.com/showthread.php?t=1498298&page=7 - and trying to get the bootloader to run the LEGEIMG.zip file, it flashes up stating "no image or wrong image!", it runs too fast to read it exactly.
- then looking at the same error this guy was getting at (see the 'EDIT: It seems the LEGEIMG' post onwards) http://forums.whirlpool.net.au/archive/1657826 - they have the same Vodfone Legend as me, a gold card had to be used to do the above update process (which should update HBOOT).
- this is the only HBOOT update process I've seen, but isn't clear as they look like they're on 2.2 and HBOOT 1.01.
............................Good grief
feed3 said:
in short, hard bricked means your phone is totally unuseable, usually because of hardware defects but also might be cause by flashing wrong ROM, for example flashing ROM that actually not built for your device. Usually, you cannot do anything with it, cannot enter fastboot, recovery etc. Soft brick is repairable, you still can boot to recovery or even to the OS. Might be caused by some partition corruption (in the case of usb bricked, it is /misc partition).
If you use htc dev path to unlock your bootloader, no need for gold card. Thats for sure.
If your phone is usb soft bricked (among the symptoms are you will be able to boot into the OS ONLY if your phone are pluged in into usb, and/or adb not working at all) then google or search in xda for "htc legend+usb brick" and fix it. I'm pretty sure only then you can update your HBOOT and therefore unlock your bootloader via htc dev.
Once done, go to HERE and flash cwm using s-off method (dont care about your s-on that you see in your bootloader, the "UNLOCKED" word in it is more important)
Click to expand...
Click to collapse
Curveau said:
In response:-
Thanks for the clarification.
- when using the process here http://forum.xda-developers.com/showthread.php?t=1498298&page=7 - and trying to get the bootloader to run the LEGEIMG.zip file, it flashes up stating "no image or wrong image!", it runs too fast to read it exactly.
- then looking at the same error this guy was getting at (see the 'EDIT: It seems the LEGEIMG' post onwards) http://forums.whirlpool.net.au/archive/1657826 - they have the same Vodfone Legend as me, a gold card had to be used to do the above update process (which should update HBOOT).
- this is the only HBOOT update process I've seen, but isn't clear as they look like they're on 2.2 and HBOOT 1.01.
............................Good grief
Click to expand...
Click to collapse
EXACTLY the same error message that you got, HERE and the op solve it.
Btw, during unlocking my bootloader, i've never encounter (or did i forget already??) to requiring this zip file. Isn't bootloader RUU from HTCdev is all we need? I think thats the only file i have to get (apart from the unlock bin file of course) if my memory doesn't cheat me..
Sure - but as the guy mentions formatting to FAT32, that's usually associated with goldcard creation right.
I've ran the bootloader RUU from HTC Dev a few times, and it always says that the ROM (HBOOT, build(?)) needs updating. Thus trying the aforementioned process (post 62 http://forum.xda-developers.com/showthread.php?t=1498298&page=7) to try and get the Rom (HBOOT) updated, which didn't work, which then loops back round to dealing with the zip file read error.
feed3 said:
EXACTLY the same error message that you got, HERE and the op solve it.
Btw, during unlocking my bootloader, i've never encounter (or did i forget already??) to requiring this zip file. Isn't bootloader RUU from HTCdev is all we need? I think thats the only file i have to get (apart from the unlock bin file of course) if my memory doesn't cheat me..
Click to expand...
Click to collapse
I'm getting more confuse here. I've never use goldcard as i reluctant to "sacrifice" my one and only card but here i am with unlocked bootloader. The RUU file is the one that will update your bootloader. Read instructions at htc dev carefully.. good luck..
Sent from my Legend using xda app-developers app
You need to read this post by blay0, it instructs how to update hboot without going back to stock, using gold card or any other outdated method of rooting (unless your on hboot less than 1.00 then you should follow the s-off method of rooting)
http://forum.xda-developers.com/showthread.php?p=22613990
Sent from my Legend using xda app-developers app
I think the reason I can't do the blay0 method is because of the stock sd card I'm using. It's not picking up the rom zip file.
I've ordered another http://www.kikatek.com/P188409/SDC10-8GB-Kingston-MicroSDHC-8GB-Card-Class-10?source=froogle
Will try again, and if that doesn't work - try this other method (as the guy here has HBOOT 1.00 and a Vodafone Legend too) http://chrg.zxq.net/htc-legend-root.html.
Many thanks for all your help people.
Will report back any success for the benefit of others.
All the best
ranger4740 said:
You need to read this post by blay0, it instructs how to update hboot without going back to stock, using gold card or any other outdated method of rooting (unless your on hboot less than 1.00 then you should follow the s-off method of rooting)
http://forum.xda-developers.com/showthread.php?p=22613990
Sent from my Legend using xda app-developers app
Click to expand...
Click to collapse
Hi guys,
Good news! I unlocked the bootloader with my 'new' SD card using the blay0 process (from the last post).
This is the first time I've done this though, and am just trying to figure out how to flash CyanogenMod 7.2.
ROM Manager doesn't work with 2.1 (installed) any more.
Can someone please briefly explain how I would flash.
Many thanks
Curveau said:
I think the reason I can't do the blay0 method is because of the stock sd card I'm using. It's not picking up the rom zip file.
I've ordered another http://www.kikatek.com/P188409/SDC10-8GB-Kingston-MicroSDHC-8GB-Card-Class-10?source=froogle
Will try again, and if that doesn't work - try this other method (as the guy here has HBOOT 1.00 and a Vodafone Legend too) http://chrg.zxq.net/htc-legend-root.html.
Many thanks for all your help people.
Will report back any success for the benefit of others.
All the best
Click to expand...
Click to collapse
SOLVED
Ah, done !! Woohoo!
That was lots of work. Well, easy via the HTCDev method <<
To get 7.2 on followed here:-
see s-off method to install recovery image http://forum.xda-developers.com/showthread.php?t=1290841&highlight=clockwork
To get into the recovery – use the col down + power button
Follow Method via Recovery here http://wiki.cyanogenmod.com/wiki/HTC_Legend:_Full_Update_Guide
Good luck everyone and thanks again XDA
Curveau said:
Hi guys,
Good news! I unlocked the bootloader with my 'new' SD card using the blay0 process (from the last post).
This is the first time I've done this though, and am just trying to figure out how to flash CyanogenMod 7.2.
ROM Manager doesn't work with 2.1 (installed) any more.
Can someone please briefly explain how I would flash.
Many thanks
Click to expand...
Click to collapse
Hello,
take the recovery-clockwork-5.0.2.0-legend.zip , put it on your SD-card and rename it to update.zip. Then use th S-ON-method from here and you will have no problem.
so there is no way to return the legend back to stock rom after all ?