Related
So I bought a nook color, downloaded BN v1.2 software and went about installing CM7 on my 8GB Sandisk Class 4 microSD. I am using a Macbook to flash on the sd card.
First trial: used verygreen's instructions on this site (many thanks). Installed CM7 successfully (yay), downloaded gapps and tried to do 2 finger recovery boot (as per instructions). Didn't work, so started ROM manager, installed CWR, downloaded gapps thru ROM manager then tried to boot into recovery. This didn't work. I then read a thread which said I had to do a regular restart after installing CWR for the installation to be complete. So ...
Second trial: reinstalled CM7, started ROM manager, installed CWR, powered down, powered up, tried to install gapps thru ROM manager, and internet connection hung up. Didn't want to mess with it, so ...
Third trial: reinstalled CM7, started ROM manager, installed CWR, powered down, powered up, powered down, powered up (just in case), install gapps thru ROM manager, and still couldn't boot into recovery. Then there was a suggestion to place CM7 zip and gapps zip on my sd card at the same time prior to first run of CM& on nook, so ...
Forth trial: flash CM7 and gapps zip on sd card. Put sd card into nook, booted, installed CM7, got 3 more apps in folder, but no marketplace (which is the reason I am going through all this frustration in the first place). Started ROM manager, installed CWR, powered down, powered up, powered down, powered up, install gapps thru ROM manager (again?), and still couldn't boot into recovery.
Note: through all these iterations, I have tried booting into recovery mode
1. via ROM manager
2. via reboot options (as opposed to power off)
3. via holding the nook button and power button in different order/time lengths.
I have been messing with this for over 4 hours last night and a couple of hours today. I know that it should not be this hard, but ...
I had planned on overclocking the machine next, but I can't seem to get beyond this step.
I found the installation guide for installing overclocked CM7 with CWR on eMMC on this site, but with as much trouble as I'm having with sd card installation, I'll end up bricking the "unbrickable" nook.
Prior to all this, I tried the HC instructions, but had trouble with marketplace install then too. I figure this was more stable, most of the bugs were worked out and had more support. Any assistance with this is greatly appreciated.
So, after the last trial, and several power on's later, Marketplace showed up -> I don't need to figure out ROM manager/boot recovery right now. I don't know when it showed up though, as I was not looking for it and wasn't paying attention (O_O).
In case this might help someone else, here is my guess as to what happened. It likely showed up after one of my recovery boot attempts. I held the N button and the power button. I kept holding it after the first startup screen faded, returned, then went away again. It booted into the installation screen I got when I first installed CM7 with the penguin in the upper left hand side (in landscape mode; this is NOT the recovery screen based on the youtube vids and other images I've seen). It was very brief, and only had <20 lines of text, one of which stated something to the effect that CM was installed and it would not need to install it. My guess is that it found the gapps zip file I had put in the boot drive along with CM7 update zip file prior to installing it in the nook, and unpackaged it and installed it then.
Reference points: when I installed CM7 without the gapps, I had 25 apps on my nook. After I co-installed them, I had ~28 (not 100% sure; one of them was talk). When I found marketplace (ie after the funky recovery boot attempt mentioned above), I had 31 apps.
Shiny1 said:
So I bought a nook color, downloaded BN v1.2 software and went about installing CM7 on my 8GB Sandisk Class 4 microSD. I am using a Macbook to flash on the sd card.
First trial: used verygreen's instructions on this site (many thanks). Installed CM7 successfully (yay), downloaded gapps and tried to do 2 finger recovery boot (as per instructions). Didn't work, so started ROM manager, installed CWR, downloaded gapps thru ROM manager then ... /snip
Click to expand...
Click to collapse
And there's where you started making it very complicated.
If you had read through verygreen's thread, you'd have realized that the "2 finger recovery boot" is timing sensitive. Hold N button down, hold power button, keep holding both buttons while it boots up, start counting to three only when you see "Touch the future..." come up on screen, release the N button on three but keep holding down the power button for another few seconds. And it will go into recovery.
And, you need to have wi-fi set up and enabled to install gapps/market, you can install both CM7/gapps at the same time but market won't show until wi-fi is running and a lot of people get confused. That's the reason why the instructions tell you to install CM7 first, set up your wi-fi, and then only add gapps/market after. You didn't mention setting up wi-fi, I guess somewhere along the line you did enable it and that's when market showed up.
For anyone reading this and contemplating installing CM7/gapps/market onto SD card, make sure you follow the directions in verygreen's post to the letter. It works.
I originally got CM7 and gapps working fine on my SD card in my nook. But today, I wanted to start over with another SD card. Using verygreen's step-by-step instructions again, CM7 loads fine, but for the life of me I can't get the nook to boot into recovery mode to install gapps. I swear I have tried every timing combination I can think of, but still can't get into recovery mode. I might just add gapps to the SD card when adding CM7. Then turn on wifi.
Trouble getting into Recovery Mode
Same problem here... I originally installed CM7 on an 8GB SD card back in late March, adding gapps at the same time. It's been working flawlessly, through many, many nightly updates, until yesterday when it refused to boot into Recovery mode. Now it hangs on the "Future of Reading" screen. I'm going to try wiping the SD card and starting over.
EDIT: OK...Used Easeus Partition Manager to wipe the SD card. Was then able to use verygreen's tools and steps to recreate CM7 bld 68. Then successfully updated to bld 69. Obviously lost all my data, but at least everything seems to be working.
Can't enter recovery mode either
I'm running CyanogenMod-7-05252011-NIGHTLY-encore in kernel version 2.6.32.9 [email protected] # 174, Android version 2.3.4 on a nook color I bought five days ago. I've gotten CM7 to boot.
Following the instructions to install Android Market and Google Apps on Nook Color CM7 at the-ebook-reader.com/nook-color-cm7.html hasn't worked. I can't get into recovery mode, never get the "Touch the Future of Reading" display (don't get this in B&N nook color mode either, just "Read Forever" since I installed software version 1.2.0).
I've put the gapps-gb-20110307-signed.zip file 'as is' (NOT unzipped) into the microSD card's root directory.
What happens is this: I hold down the 'n' and the main power button. The screen flashes white very briefly, then the white lettering on green cyanogen appears for less than a second before disappearing. The nook color is powered off then.
Anybody know what's going on, and how I can get into recovery mode to load the google apps pack and android market?
Got gapps to load using ROMmanager to enter recovery mode - no problems now.
Me, too--I hate to say...
I've got CM 7.0.3 running from an SD card, and everything went well until I tried to reboot into recovery mode. I've followed the instructions in the beginning of Verygreen's thread, the ones listed above (which are slightly different), tried from Rom Manager, the power button>reboot>recovery method, as well as various other tutorials and even videos. I'm still unable to get my NC to reboot into recovery mode. I double checked, and the gapps .zip file is in the correct partition, as well. I'm at a loss at this point. Any help would be greatly appreciated, and I'm sorry for all the bother.
Thank you.
UPDATE: Reformatted my sd card (on a Mac), then tried again using 7.0.3 and the 93 nightly instead of 94, and everything is working fine now. Thanks very much anyway, though!!
I am having the same issues. Brand new nook. Installer VeryGreen's instructions. Booted using sdcard, setting up wireless. Rebooted. Attempted to go into recovery mode using the key press method, using ROMmanager and via the Reboot menu option. In all instances, it just boots up normally. I also re-imaged the card with the latest stable release of CM7 but that did not make any difference.
Thoughts?
And given that I can't install the Marketplace, is there anyway to install apps? Right now I have a vanilla install, while nice, does not give me what I need in terms of functionality.
thx.
Got mine working!
I had the same issue - generic uSD v1.3, CM7 7.0.3 Stable, and couldn't get into recovery no matter what.
With nothing to lose, I started from scratch and put gapps on the uSD boot partition along with CM7, and it worked. The device was sluggish while going through the setup wizard (just decline to connect/establish an account until you exit the wizard and have enabled WiFi), but after a reboot, market is there. There were 29 apps before, and now there are 31. I think market and talk are the new ones.
Now I'm happily busy installing my apps.
Thanks to all the smart guys who make this possible.
I am having a lot of trouble getting recovery mode to actually run
I have followed the instructions and have asked a coworker for help. My 1st attempt was using the 7.0.3 stable build.My nook seems to be running CM7 fine and I was able to install the Amazon app and then download additional apps from there, but was unable to get the nook to rebot in recovery mode. I have tried a number of ways.
1) the time sequence suggested on verygreens thread (not sure I did it right)
2) power up the nook. hold the power buttong until I get a menu. select reboot in recovery mode and the select ok.
3) open the ROM manger and select reboot in recovery mode.
I have tried various repeated attempts with these while holding power,or the n button... etc. nothing happens except it boots like normal. I went into the ROM manager and updated clockwork. I also ran set permissiones in the ROM manager. then tried the various ways of rebooting in recovery mode.
I then read on here that the nightly builds worked better than 7.0.3 for one person so I formatted the SD and reattepted every listed above with the 8-8-2011 (cm_encore_full-154) nightly build. It is still not able to reboot in recovery mode.
I had 1 minor success when I turned the nook off and removed the micro SD it DID go int recovery mode. I reinserted the micor SD and used the menu to install the zip file... but after rebooting nook I still don't see any new apps.
Please someone give me some suggestions.
To all:
The installer image 1.3 from verygreens thread does not work with 7.0.3 or below. Use the 7.1.0 RC or recent nightly. 150 is supposed to be pretty good.
---
- Sent from my LG Optimus V using Tapatalk
I just picked up a Nook Color and an 8gb MicroSD. I went through the instruction here to make a Android 2.3 boot disk.
http://forum.xda-developers.com/showthread.php?t=1000957
It all worked fine until the very end where I installed the file with the Market and googleapps. I put that on the SD and put it the NC, rebooted into Recovery mode. It seemed to work and shut itself off. When I started the NC again it seemed to start, but it gets stuck at the circle logo with the spinning arrow... forever (okay, I waited 20 minutes). I can shut it off, but can't get it to ever go past this screen. I redid the whole process a second time and got the same result.
Any ideas?
What CM7 did you use? 7.0.3 stable isn't supported by that installer, only the more recent nightlies (may as well start with 150 at this point) or the 7.1 release candidate.
Were you able to boot into CM7 and set up Wi-Fi before you tried to install gapps?
The next step is probably to re-download CM7 and gapps (in case the files were corrupted) and boot into recovery to install again.
I was able to boot up before I put the gapps on there and went online (weak signal from a neighbor for internet, but I got the google home page to load).
I think I used cm_encore_full-151.zip , which one should I use?
Everything runs smoothey until I try to install gapps, it seems to install them, but when I reboot it just loops on the spinning arrow animation forever.
Try the steps from this site and make sure you use CWR ver. 3.2.0.1.
http://mrm3.net/nook-color-how-to-install-cyanogenmod-nightlies/
Note, you do not have to boot up CM7 first. You can install CM7 and the app pack during the initial install. Just install the ROM .zip before you install the app .zip.
patruns said:
Try the steps from this site and make sure you use CWR ver. 3.2.0.1.
http://mrm3.net/nook-color-how-to-install-cyanogenmod-nightlies/
Note, you do not have to boot up CM7 first. You can install CM7 and the app pack during the initial install. Just install the ROM .zip before you install the app .zip.
Click to expand...
Click to collapse
He booted it off the uSD, m8
Nothing I do seems to help. I can get a nice Android 2.3 tablet, as long as I don't try to install gapps. If I install them it just loops forever in boot. Is there any other way to get gappos on it besides putting a zip file on the SD and rebooting?
Did you try installing both CM7 and gapps at the same time (putting both zips on the SD together)? If it works, just make sure to opt-out of account set-up and get Wi-Fi configured.
ETA: also, if nothing else you should be able to install the Amazon app market.
Nothing seems to work. Every time I boot up with gapps it just has the spinning ciricle boot screen FOREVER.
I have a NC 1.2. I am able to root using a CWM 3.0.2.8 Msd card with Manual Nooter no problem. The problem occurs when I shut it off and then reboot. It gets to the part where the words "Nook Color" start scrolling across the screen. "Nook Color" completes one time successfully and when it starts scrolling again, it stops halfway through the first "o" in "Color", and just repeats indefinitely. The only thing I could do is completely reset, eight failed boots. At first I thought it may be an older version of CWM on my Msd card so I made a new one with v. 3.0.2.8 and rooted successfully, but first time I shut it off and rebooted, it happened again. I am thinking only thing to do is never turn it off. Any ideas would be greatly appreciated.
reebz said:
I have a NC 1.2. I am able to root using a CWM 3.0.2.8 Msd card with Manual Nooter no problem. The problem occurs when I shut it off and then reboot. It gets to the part where the words "Nook Color" start scrolling across the screen. "Nook Color" completes one time successfully and when it starts scrolling again, it stops halfway through the first "o" in "Color", and just repeats indefinitely. The only thing I could do is completely reset, eight failed boots. At first I thought it may be an older version of CWM on my Msd card so I made a new one with v. 3.0.2.8 and rooted successfully, but first time I shut it off and rebooted, it happened again. I am thinking only thing to do is never turn it off. Any ideas would be greatly appreciated.
Click to expand...
Click to collapse
What version MN are you using? You’re not wiping anything when you flash MN, right?
reebz said:
…At first I thought it may be an older version of CWM on my Msd card so I made a new one with v. 3.0.2.8 and rooted successfully, but first time I shut it off and rebooted, it happened again. I am thinking only thing to do is never turn it off.
Click to expand...
Click to collapse
Are you saying that after you flash MN, you remove the SD card, it will fully boot up into the OS, then when you turn off the device and try to turn it back on, it will then not boot up? Or, are you saying that after you flash MN, you remove the SD card, and then the device fails to boot?
It sounds to me like you are wiping the system before you flash MN, but until I get the answers to the above questions, I can’t say for sure. MN is a add on pack for the stock OS, not a full rom, so you don’t wipe before you flash.
I have latest version of MN. I do not wipe anything. I boot into CWM and install MN with a msd card. Upon successful installation of MN, I remove msd card and reboot successfully that one time into a rooted NC. I can use Gmail app, download and install from both Android and Amazon markets. However, if I power down completely and reboot, it loops as explained in my OP.
reebz said:
I have latest version of MN. I do not wipe anything. I boot into CWM and install MN with a msd card. Upon successful installation of MN, I remove msd card and reboot successfully that one time into a rooted NC. I can use Gmail app, download and install from both Android and Amazon markets. However, if I power down completely and reboot, it loops as explained in my OP.
Click to expand...
Click to collapse
Are you updating Adobe Flash? You can't directly update Adobe Flash from the Nook Color. The most common issues that will cause a boot loop on a NC after having a fully working device, are installing the wrong kernel, and updating Adobe Flash from the Market. If you updated Adobe Flash, download the attached file, and flash with CWM. The file should delete the old flash player, and install the updated one. This should give you a working device again. If it does work for you, please report back here so others will know what the fix it.
GMPOWER said:
Are you updating Adobe Flash? You can't directly update Adobe Flash from the Nook Color. The most common issues that will cause a boot loop on a NC after having a fully working device, are installing the wrong kernel, and updating Adobe Flash from the Market. If you updated Adobe Flash, download the attached file, and flash with CWM. The file should delete the old flash player, and install the updated one. This should give you a working device again. If it does work for you, please report back here so others will know what the fix it.
Click to expand...
Click to collapse
I have updated Flash Player from the Market after rooting. If I remember correctly, I've powered down after rooting and installing numerous apps, including Flash, and rebooted . Maybe that's the culprit. I have not installed a different kernel. I'll go ahead and install the attached zip, with much thanks, but I don't know if I want to power off and reboot, for fear of dreaded boot loop.
Ok, I installed Flash Fix and rebooted, and the same boot loop is occurring. Looks like time to reset and reroot, and for now, never turn it off.
reebz said:
I have updated Flash Player from the Market after rooting. If I remember correctly, I've powered down after rooting and installing numerous apps, including Flash, and rebooted . Maybe that's the culprit. I have not installed a different kernel. I'll go ahead and install the attached zip, with much thanks, but I don't know if I want to power off and reboot, for fear of dreaded boot loop.
Ok, I installed Flash Fix and rebooted, and the same boot loop is occurring. Looks like time to reset and reroot, and for now, never turn it off.
Click to expand...
Click to collapse
I just realized that I missed a step in the install script for that file, that is why it did not work for you. Yes, adobe flash is your problem. To update Adobe Flash on the nook color, you have to uninstall the old version, and then install the new adobe flash.
For all future references, I have attached the working Adobe Flash fix file. It includes flash version 10.3.186.3, that was released today. It has been tested to work, and you can allow auto-update in the market without future problems.
Ok, thanks, I will reluctantly give this a try when I get home from work.
Edit: Ok, now. I'm trying to uninstall Flash Player and having difficulties. It doesn't show up in the app drawer, so I go to Market to see if there is an uninstall option, but there is only an update option, so I updated, and then uninstalled to see if that would work, but it still showed up in "my apps", in market. I opened up app drawer and selected manage apps and found it, but selecting the uninstall button does nothing. I then tried installing Titanium Backup and after installing, Titanium Backup won't open and doesn't even show up in my app drawer. So, I'm a little stymied now. Unsure what to do next
reebz said:
Ok, thanks, I will reluctantly give this a try when I get home from work.
Edit: Ok, now. I'm trying to uninstall Flash Player and having difficulties. It doesn't show up in the app drawer, so I go to Market to see if there is an uninstall option, but there is only an update option, so I updated, and then uninstalled to see if that would work, but it still showed up in "my apps", in market. I opened up app drawer and selected manage apps and found it, but selecting the uninstall button does nothing. I then tried installing Titanium Backup and after installing, Titanium Backup won't open and doesn't even show up in my app drawer. So, I'm a little stymied now. Unsure what to do next
Click to expand...
Click to collapse
Titanium Backup is going to be your best bet to do the uninstall process. When you selected update Flash from the market, then went and uninstalled it, you were only uninstalling the update. If TB installed, then it should show up in the app drawer of Zeam launcher. You can go into the market, and select to open it from there. Sometime it will not open on first attempt, because it is trying to ask you to give it root permission. If you still have trouble with it not opening, then uninstall it, and try to install it again. You can also open up the “Superuser” app to make sure that it has not been denied root permission.
TB definitely didn't appear in Zeam app drawer. I'm charging now and give it another shot in a bit.
Edit: Success. I got TB installed. I made a stupid error. I only installed the paid app, not the free also. I got Flash uninstalled and installed your Flash Fix.zip with numerous reboots with no boot loops.
GMPOWER, Thanks for your assistance
GMPOWER said:
For all future references, I have attached the working Adobe Flash fix file. It includes flash version 10.3.186.3, that was released today. It has been tested to work, and you can allow auto-update in the market without future problems.
Click to expand...
Click to collapse
I don't normally bump old threads, but this just saved me
Thanks a lot, I was at wits end figuring out why it was boot looping.
dreadwing said:
I don't normally bump old threads, but this just saved me
Thanks a lot, I was at wits end figuring out why it was boot looping.
Click to expand...
Click to collapse
Same here. Big thanks to GMPower! (My first post here, now I can use the Thanks button!)
Total noob question. This is my first time rooting. I got the root to work fine but updated Flash before finding out about the loop. I'm not sure what I'm supposed to do to fix this problem. OP in this thread said he reinstalled MN 4.6.16 via bootable SD with CWM and could get his nook to boot up. I tried that and rebooted but I'm still getting stuck in the loop.
Do I need to wipe my nook before reapplying MN?
dahcheet said:
Total noob question. This is my first time rooting. I got the root to work fine but updated Flash before finding out about the loop. I'm not sure what I'm supposed to do to fix this problem. OP in this thread said he reinstalled MN 4.6.16 via bootable SD with CWM and could get his nook to boot up. I tried that and rebooted but I'm still getting stuck in the loop.
Do I need to wipe my nook before reapplying MN?
Click to expand...
Click to collapse
Use the zip file in post #7 (in this thread). Drop it onto the same SD card you used to load MN 4.6.16. Put the SD card in and it'll boot to CWM....then flash that zip file the same way you flashed MN. Then, power off the NC, remove the CWM SD card and put in your regular SD and turn the NC back on. That should be it...no more boot loop.
I've got the same issue as the thread started and I downloaded the zip from post 7 and flashed it just like I flashed MN, but it's still boot looping. It gets a bit farther into the "Nook Color" logo but keeps repeating.
Boot Loops NC 1.3
GMPOWER said:
For all future references, I have attached the working Adobe Flash fix file. It includes flash version 10.3.186.3, that was released today. It has been tested to work, and you can allow auto-update in the market without future problems.
Click to expand...
Click to collapse
This problem started for me on Rooted 1.3. October 5th, Applied this fix.
Thanks GMPOWER
I figure I will explain my problem in more detail. I am working with my girlfriend's Nook trying to get it rooted. The first time I did she had 1.2 stock and I rooted it successfully. She updated flash not knowing that it would cause a boot loop. I had no idea how to fix it so she set it back to factory settings and procedded to update to 1.3 to see if that would solve the boot loop. I rooted it again and it started boot looping again. I found this thread and the flash fix. I flashed it onto the Nook and it fixed the loop problem.
Well she found out that the marketplace has limited visibility with 1.3 and wanted to go back to 1.2 to have her full visibility back. So she factory reset it again, I rooted it again and it started boot looping again. This time though the fix from post 7 isn't helping. I flash it and then reboot and it loads the "Nook Color" logo once fully and then stops and starts it over again and gets stuck at "Nook Col".
Is there anyone who might be able to help me with what the problem is, or am I gonna have to reset it back to stock, use Titanium Backup to remove flash and then use the zip from post 7? I know that it's not a root problem because I successfully rooted my mom's Nook before my girlfriends and her's is working fine.
Followed your instructions and my problem solved, many thanks!
johnny15 said:
Use the zip file in post #7 (in this thread). Drop it onto the same SD card you used to load MN 4.6.16. Put the SD card in and it'll boot to CWM....then flash that zip file the same way you flashed MN. Then, power off the NC, remove the CWM SD card and put in your regular SD and turn the NC back on. That should be it...no more boot loop.
Click to expand...
Click to collapse
my first post. thanks GMpower
just had this happen to me too. I've tried the flash update, and I get slightly more of the nook color boot graphic but it still hangs.
any thoughts?
hey i just attempted to root my wife's nook color, 1.3, using this method http://forum.xda-developers.com/showthread.php?t=1054027
i have made the boot disk and pushed both nooter zips to disk, cwm comes up and it runs both zips just fine, ive tried both one after other ten reboot, reboot in between, wipe dalvik and the run but i always get stuck in the boot loop
can anyone tell me what im doing wrong here
and the plot thickens... so i did the 8 failed manual reset, and rebooted to stock, repeated process.. im out of bootloop but it appears the touch screen doesnt work anymore???
yeah so no matter how many times i 8 fail reset still no touch screen, all other buttons work, tried reinstalling clockwork and nothing...i bought the insurance, do i need to run it over cause im outta ideas, my first thought was ui was missing file but it should go back if i reset shouldnt it???
just shoot me..please
ok back to stock, re root, boot loop again, re stock , cm7 (update-cm-7.1.0-encore-signed) + gapps (gapps-gb-20110307-signed) and now application setup wizard has stopped unexpectedly.....stuck...thoughts? please am i over thinking/looking something
day two...
i created sd boot img with cwm 3.2.08, im seeing that i need to use cwm 3.2.01 in a few places.. when i get the file from clockwork (recovery-clockwork-3.2.0.1-encore) and try to write the image to the sd card something is wrong, its not a format that the windows recognizes and so i cant add zips to it and i get nothing in the nook. ive tried to reformat from the pc and in an old android phone i have but its always the same when i try to write to sd , is this the wrong image, can i find it somewhere else
i am using same 8gb sd card i made first boot disk out of, do i need to use a new one??
i got it to work i have good cwm 3.2.01 on nook...
stock + root?
ok it seems that cwm 3.2.0.8 was definitely my problem, i switched to recovery-clockwork-3.2.0.1-encore which i got from http://tinyw.in/0Vw
problem remains that when i flash man nooter 18 then 16 i get nothing, I was stuck on "n" load screen not even a boot loop
i then pushed cm7 again and i am operating as a full android tablet, i want the stock nook image with gapps can anyone help.. im leaving be till i get a answer, didnt want to update to 1.4 or downgrade to 1.2 havent seen a stock img of 1.3 anywhere
Nook color running Racks triple boot via micro SD card. Micro SD card is a Sandisk 8GB class 4 card.
Was previously running fine for many months with the 2/2/12 roms. I would run CM7 99% of the time and I would get a random reboot here and there, but otherwise very stable.
A couple days ago, I had a random crash and tried to reboot CM7. I could get passed the boot loader screen, but then would have a continuous boot loop with the blue android symbol.
Thinking something was corrupted with the rom, I booted to recovery and tried flashed the rom along with gapps. Still boot looping.
I booted to CM9, and was able to run. So I downloaded the latest CM7 and CM9 roms for Racks triple boot. Flashed both along with the gapps and CM9 fix. Apparently I got lucky and was able to boot into CM7.... once. Thinking everything was OK, I went on with my life and ran the new CM7 happily.
Now, a few days later, I've tried to reboot and I'm back at the same boot loop with the arrow spiraling around the a blue skateboarding android. Note, in that short time that I was running the newest Racks triple boot CM7 rom, I did not run a backup, so, I'm basically out of luck with recovery via CWM.
I've flashed the 2/2/12 rom as well as the latest rom to see if either would work again. nothing... still boot looping... for hours now.
Any suggestions other than wiping the SD clean and starting with a fresh install?
Thanks all.
~mike
Bump...
Been a bit, no responses yet. Anyone have any ideas?
Thanks,
~mike
I think the fresh install will help since you already tried partial reinstalling the roms.
Produced by NookColor at ICS AOKP 4.0.4
Nook Color stuck in load screen
I have a nook with CM7 installed on it. was going return my nook to stock to give it to my little sister, but when i went to install the stock stuff back on it got stuck in a loop. It won't boot from an uSD card with clockwork on it and when I tried the 7 hard boot in a row trick, it didn't do anything. Did i really brick the thing? or can it be recovered?
doodlebug81 said:
I have a nook with CM7 installed on it. was going return my nook to stock to give it to my little sister, but when i went to install the stock stuff back on it got stuck in a loop. It won't boot from an uSD card with clockwork on it and when I tried the 7 hard boot in a row trick, it didn't do anything. Did i really brick the thing? or can it be recovered?
Click to expand...
Click to collapse
You are in a recovery bootloop with no recovery installed. Go to my tips thread linked in my signature. Read item A8. You need to make and use my special bootable CWM SD (select the 'larger' image). Then if you want to return to stock, read item A15.