Related
So I bought a nook color, downloaded BN v1.2 software and went about installing CM7 on my 8GB Sandisk Class 4 microSD. I am using a Macbook to flash on the sd card.
First trial: used verygreen's instructions on this site (many thanks). Installed CM7 successfully (yay), downloaded gapps and tried to do 2 finger recovery boot (as per instructions). Didn't work, so started ROM manager, installed CWR, downloaded gapps thru ROM manager then tried to boot into recovery. This didn't work. I then read a thread which said I had to do a regular restart after installing CWR for the installation to be complete. So ...
Second trial: reinstalled CM7, started ROM manager, installed CWR, powered down, powered up, tried to install gapps thru ROM manager, and internet connection hung up. Didn't want to mess with it, so ...
Third trial: reinstalled CM7, started ROM manager, installed CWR, powered down, powered up, powered down, powered up (just in case), install gapps thru ROM manager, and still couldn't boot into recovery. Then there was a suggestion to place CM7 zip and gapps zip on my sd card at the same time prior to first run of CM& on nook, so ...
Forth trial: flash CM7 and gapps zip on sd card. Put sd card into nook, booted, installed CM7, got 3 more apps in folder, but no marketplace (which is the reason I am going through all this frustration in the first place). Started ROM manager, installed CWR, powered down, powered up, powered down, powered up, install gapps thru ROM manager (again?), and still couldn't boot into recovery.
Note: through all these iterations, I have tried booting into recovery mode
1. via ROM manager
2. via reboot options (as opposed to power off)
3. via holding the nook button and power button in different order/time lengths.
I have been messing with this for over 4 hours last night and a couple of hours today. I know that it should not be this hard, but ...
I had planned on overclocking the machine next, but I can't seem to get beyond this step.
I found the installation guide for installing overclocked CM7 with CWR on eMMC on this site, but with as much trouble as I'm having with sd card installation, I'll end up bricking the "unbrickable" nook.
Prior to all this, I tried the HC instructions, but had trouble with marketplace install then too. I figure this was more stable, most of the bugs were worked out and had more support. Any assistance with this is greatly appreciated.
So, after the last trial, and several power on's later, Marketplace showed up -> I don't need to figure out ROM manager/boot recovery right now. I don't know when it showed up though, as I was not looking for it and wasn't paying attention (O_O).
In case this might help someone else, here is my guess as to what happened. It likely showed up after one of my recovery boot attempts. I held the N button and the power button. I kept holding it after the first startup screen faded, returned, then went away again. It booted into the installation screen I got when I first installed CM7 with the penguin in the upper left hand side (in landscape mode; this is NOT the recovery screen based on the youtube vids and other images I've seen). It was very brief, and only had <20 lines of text, one of which stated something to the effect that CM was installed and it would not need to install it. My guess is that it found the gapps zip file I had put in the boot drive along with CM7 update zip file prior to installing it in the nook, and unpackaged it and installed it then.
Reference points: when I installed CM7 without the gapps, I had 25 apps on my nook. After I co-installed them, I had ~28 (not 100% sure; one of them was talk). When I found marketplace (ie after the funky recovery boot attempt mentioned above), I had 31 apps.
Shiny1 said:
So I bought a nook color, downloaded BN v1.2 software and went about installing CM7 on my 8GB Sandisk Class 4 microSD. I am using a Macbook to flash on the sd card.
First trial: used verygreen's instructions on this site (many thanks). Installed CM7 successfully (yay), downloaded gapps and tried to do 2 finger recovery boot (as per instructions). Didn't work, so started ROM manager, installed CWR, downloaded gapps thru ROM manager then ... /snip
Click to expand...
Click to collapse
And there's where you started making it very complicated.
If you had read through verygreen's thread, you'd have realized that the "2 finger recovery boot" is timing sensitive. Hold N button down, hold power button, keep holding both buttons while it boots up, start counting to three only when you see "Touch the future..." come up on screen, release the N button on three but keep holding down the power button for another few seconds. And it will go into recovery.
And, you need to have wi-fi set up and enabled to install gapps/market, you can install both CM7/gapps at the same time but market won't show until wi-fi is running and a lot of people get confused. That's the reason why the instructions tell you to install CM7 first, set up your wi-fi, and then only add gapps/market after. You didn't mention setting up wi-fi, I guess somewhere along the line you did enable it and that's when market showed up.
For anyone reading this and contemplating installing CM7/gapps/market onto SD card, make sure you follow the directions in verygreen's post to the letter. It works.
I originally got CM7 and gapps working fine on my SD card in my nook. But today, I wanted to start over with another SD card. Using verygreen's step-by-step instructions again, CM7 loads fine, but for the life of me I can't get the nook to boot into recovery mode to install gapps. I swear I have tried every timing combination I can think of, but still can't get into recovery mode. I might just add gapps to the SD card when adding CM7. Then turn on wifi.
Trouble getting into Recovery Mode
Same problem here... I originally installed CM7 on an 8GB SD card back in late March, adding gapps at the same time. It's been working flawlessly, through many, many nightly updates, until yesterday when it refused to boot into Recovery mode. Now it hangs on the "Future of Reading" screen. I'm going to try wiping the SD card and starting over.
EDIT: OK...Used Easeus Partition Manager to wipe the SD card. Was then able to use verygreen's tools and steps to recreate CM7 bld 68. Then successfully updated to bld 69. Obviously lost all my data, but at least everything seems to be working.
Can't enter recovery mode either
I'm running CyanogenMod-7-05252011-NIGHTLY-encore in kernel version 2.6.32.9 [email protected] # 174, Android version 2.3.4 on a nook color I bought five days ago. I've gotten CM7 to boot.
Following the instructions to install Android Market and Google Apps on Nook Color CM7 at the-ebook-reader.com/nook-color-cm7.html hasn't worked. I can't get into recovery mode, never get the "Touch the Future of Reading" display (don't get this in B&N nook color mode either, just "Read Forever" since I installed software version 1.2.0).
I've put the gapps-gb-20110307-signed.zip file 'as is' (NOT unzipped) into the microSD card's root directory.
What happens is this: I hold down the 'n' and the main power button. The screen flashes white very briefly, then the white lettering on green cyanogen appears for less than a second before disappearing. The nook color is powered off then.
Anybody know what's going on, and how I can get into recovery mode to load the google apps pack and android market?
Got gapps to load using ROMmanager to enter recovery mode - no problems now.
Me, too--I hate to say...
I've got CM 7.0.3 running from an SD card, and everything went well until I tried to reboot into recovery mode. I've followed the instructions in the beginning of Verygreen's thread, the ones listed above (which are slightly different), tried from Rom Manager, the power button>reboot>recovery method, as well as various other tutorials and even videos. I'm still unable to get my NC to reboot into recovery mode. I double checked, and the gapps .zip file is in the correct partition, as well. I'm at a loss at this point. Any help would be greatly appreciated, and I'm sorry for all the bother.
Thank you.
UPDATE: Reformatted my sd card (on a Mac), then tried again using 7.0.3 and the 93 nightly instead of 94, and everything is working fine now. Thanks very much anyway, though!!
I am having the same issues. Brand new nook. Installer VeryGreen's instructions. Booted using sdcard, setting up wireless. Rebooted. Attempted to go into recovery mode using the key press method, using ROMmanager and via the Reboot menu option. In all instances, it just boots up normally. I also re-imaged the card with the latest stable release of CM7 but that did not make any difference.
Thoughts?
And given that I can't install the Marketplace, is there anyway to install apps? Right now I have a vanilla install, while nice, does not give me what I need in terms of functionality.
thx.
Got mine working!
I had the same issue - generic uSD v1.3, CM7 7.0.3 Stable, and couldn't get into recovery no matter what.
With nothing to lose, I started from scratch and put gapps on the uSD boot partition along with CM7, and it worked. The device was sluggish while going through the setup wizard (just decline to connect/establish an account until you exit the wizard and have enabled WiFi), but after a reboot, market is there. There were 29 apps before, and now there are 31. I think market and talk are the new ones.
Now I'm happily busy installing my apps.
Thanks to all the smart guys who make this possible.
I am having a lot of trouble getting recovery mode to actually run
I have followed the instructions and have asked a coworker for help. My 1st attempt was using the 7.0.3 stable build.My nook seems to be running CM7 fine and I was able to install the Amazon app and then download additional apps from there, but was unable to get the nook to rebot in recovery mode. I have tried a number of ways.
1) the time sequence suggested on verygreens thread (not sure I did it right)
2) power up the nook. hold the power buttong until I get a menu. select reboot in recovery mode and the select ok.
3) open the ROM manger and select reboot in recovery mode.
I have tried various repeated attempts with these while holding power,or the n button... etc. nothing happens except it boots like normal. I went into the ROM manager and updated clockwork. I also ran set permissiones in the ROM manager. then tried the various ways of rebooting in recovery mode.
I then read on here that the nightly builds worked better than 7.0.3 for one person so I formatted the SD and reattepted every listed above with the 8-8-2011 (cm_encore_full-154) nightly build. It is still not able to reboot in recovery mode.
I had 1 minor success when I turned the nook off and removed the micro SD it DID go int recovery mode. I reinserted the micor SD and used the menu to install the zip file... but after rebooting nook I still don't see any new apps.
Please someone give me some suggestions.
To all:
The installer image 1.3 from verygreens thread does not work with 7.0.3 or below. Use the 7.1.0 RC or recent nightly. 150 is supposed to be pretty good.
---
- Sent from my LG Optimus V using Tapatalk
I'm having a little trouble getting everything to run smoothly on my Nook Color CM7 install. I originally tried the latest night release and ran into a lot of force closes, apps that wouldn't run, and overall sluggishness.
So I installed 7.0.3-Encore which is supposed to be the latest stable release. I can't boot into Recovery to install gapps. I was able to boot into Recovery with the night release, but not 7.0.3-Encore. I tried 7.0.2-Encore and had the same problem.
I tried choosing "reboot" and then "boot into recovery". It just boots normally. I tried booting into recovery through the rom manager. Same thing happened.
What am I doing wrong, or what do I need to do to get this working?
Just to give a few more details. I did some more research about getting this thing to go into Recovery Mode. When I boot, I don't get the "Touch the World of Reading" text. It goes straight into "Loading". Every post that I read about getting into recovery mode says that you're supposed to release the buttons after the "Touch the World of Reading" appears. I don't get that text at all. I'm not sure what I'm doing wrong.
Next time, asking question, pls indicate you are running ROM on eMMC or booting it off uSD.
I'm pretty much having the same problem
dna59 said:
I'm pretty much having the same problem
Click to expand...
Click to collapse
I think that I figured mine out. There are two ways that you can get around this.
The easiest way is to bypass using Recovery at all to install gapps. When you put your ROM image on the SD card, put your gapps image on there as well. When it boots and installs the ROM, it will automatically install the gapps as well. Just make sure that you're in a wifi hotspot so that you can log in when you sign into gapps.
I think that my issue was that Clockwork recover wasn't installed on my system. If you to into the ROM Manager, there is an option at the top to install Clockwork Recovery. After you install it, choose the option in the ROM Manager to reboot into Recovery. This worked for me.
I changed to an internal memory install and EVERYTHING is 100% better. Don't do a SD Card install unless you have the correct type of sandisk class 2 card. Any other SD Card will make things super slow and will cause lots of force closes.
Much better to just do an internal memory install and then an overclock. Right now I'm running the latest nightly release and haven't had a single issue. Plus it lets you overclock it to 1200 Mhz right out of the box. Hope that helps!
Yea I bypassed recovery for the gapps install. However I did instal CWM through ROM manager and i still can't boot into recovery
I can tell you that I switched to Nightly build 152 and that I can also boot into recovery with the button combo at bootup. I hold the power button until the screen flashes and then press the Nook Button for about a second. When the loading screen appears I release both buttons, and it says that it's booting into recovery.
With this build I can also boot into Recovery from the ROM manager. You might want to consider trying out this build if you're still having trouble.
I have a NC 1.2. I am able to root using a CWM 3.0.2.8 Msd card with Manual Nooter no problem. The problem occurs when I shut it off and then reboot. It gets to the part where the words "Nook Color" start scrolling across the screen. "Nook Color" completes one time successfully and when it starts scrolling again, it stops halfway through the first "o" in "Color", and just repeats indefinitely. The only thing I could do is completely reset, eight failed boots. At first I thought it may be an older version of CWM on my Msd card so I made a new one with v. 3.0.2.8 and rooted successfully, but first time I shut it off and rebooted, it happened again. I am thinking only thing to do is never turn it off. Any ideas would be greatly appreciated.
reebz said:
I have a NC 1.2. I am able to root using a CWM 3.0.2.8 Msd card with Manual Nooter no problem. The problem occurs when I shut it off and then reboot. It gets to the part where the words "Nook Color" start scrolling across the screen. "Nook Color" completes one time successfully and when it starts scrolling again, it stops halfway through the first "o" in "Color", and just repeats indefinitely. The only thing I could do is completely reset, eight failed boots. At first I thought it may be an older version of CWM on my Msd card so I made a new one with v. 3.0.2.8 and rooted successfully, but first time I shut it off and rebooted, it happened again. I am thinking only thing to do is never turn it off. Any ideas would be greatly appreciated.
Click to expand...
Click to collapse
What version MN are you using? You’re not wiping anything when you flash MN, right?
reebz said:
…At first I thought it may be an older version of CWM on my Msd card so I made a new one with v. 3.0.2.8 and rooted successfully, but first time I shut it off and rebooted, it happened again. I am thinking only thing to do is never turn it off.
Click to expand...
Click to collapse
Are you saying that after you flash MN, you remove the SD card, it will fully boot up into the OS, then when you turn off the device and try to turn it back on, it will then not boot up? Or, are you saying that after you flash MN, you remove the SD card, and then the device fails to boot?
It sounds to me like you are wiping the system before you flash MN, but until I get the answers to the above questions, I can’t say for sure. MN is a add on pack for the stock OS, not a full rom, so you don’t wipe before you flash.
I have latest version of MN. I do not wipe anything. I boot into CWM and install MN with a msd card. Upon successful installation of MN, I remove msd card and reboot successfully that one time into a rooted NC. I can use Gmail app, download and install from both Android and Amazon markets. However, if I power down completely and reboot, it loops as explained in my OP.
reebz said:
I have latest version of MN. I do not wipe anything. I boot into CWM and install MN with a msd card. Upon successful installation of MN, I remove msd card and reboot successfully that one time into a rooted NC. I can use Gmail app, download and install from both Android and Amazon markets. However, if I power down completely and reboot, it loops as explained in my OP.
Click to expand...
Click to collapse
Are you updating Adobe Flash? You can't directly update Adobe Flash from the Nook Color. The most common issues that will cause a boot loop on a NC after having a fully working device, are installing the wrong kernel, and updating Adobe Flash from the Market. If you updated Adobe Flash, download the attached file, and flash with CWM. The file should delete the old flash player, and install the updated one. This should give you a working device again. If it does work for you, please report back here so others will know what the fix it.
GMPOWER said:
Are you updating Adobe Flash? You can't directly update Adobe Flash from the Nook Color. The most common issues that will cause a boot loop on a NC after having a fully working device, are installing the wrong kernel, and updating Adobe Flash from the Market. If you updated Adobe Flash, download the attached file, and flash with CWM. The file should delete the old flash player, and install the updated one. This should give you a working device again. If it does work for you, please report back here so others will know what the fix it.
Click to expand...
Click to collapse
I have updated Flash Player from the Market after rooting. If I remember correctly, I've powered down after rooting and installing numerous apps, including Flash, and rebooted . Maybe that's the culprit. I have not installed a different kernel. I'll go ahead and install the attached zip, with much thanks, but I don't know if I want to power off and reboot, for fear of dreaded boot loop.
Ok, I installed Flash Fix and rebooted, and the same boot loop is occurring. Looks like time to reset and reroot, and for now, never turn it off.
reebz said:
I have updated Flash Player from the Market after rooting. If I remember correctly, I've powered down after rooting and installing numerous apps, including Flash, and rebooted . Maybe that's the culprit. I have not installed a different kernel. I'll go ahead and install the attached zip, with much thanks, but I don't know if I want to power off and reboot, for fear of dreaded boot loop.
Ok, I installed Flash Fix and rebooted, and the same boot loop is occurring. Looks like time to reset and reroot, and for now, never turn it off.
Click to expand...
Click to collapse
I just realized that I missed a step in the install script for that file, that is why it did not work for you. Yes, adobe flash is your problem. To update Adobe Flash on the nook color, you have to uninstall the old version, and then install the new adobe flash.
For all future references, I have attached the working Adobe Flash fix file. It includes flash version 10.3.186.3, that was released today. It has been tested to work, and you can allow auto-update in the market without future problems.
Ok, thanks, I will reluctantly give this a try when I get home from work.
Edit: Ok, now. I'm trying to uninstall Flash Player and having difficulties. It doesn't show up in the app drawer, so I go to Market to see if there is an uninstall option, but there is only an update option, so I updated, and then uninstalled to see if that would work, but it still showed up in "my apps", in market. I opened up app drawer and selected manage apps and found it, but selecting the uninstall button does nothing. I then tried installing Titanium Backup and after installing, Titanium Backup won't open and doesn't even show up in my app drawer. So, I'm a little stymied now. Unsure what to do next
reebz said:
Ok, thanks, I will reluctantly give this a try when I get home from work.
Edit: Ok, now. I'm trying to uninstall Flash Player and having difficulties. It doesn't show up in the app drawer, so I go to Market to see if there is an uninstall option, but there is only an update option, so I updated, and then uninstalled to see if that would work, but it still showed up in "my apps", in market. I opened up app drawer and selected manage apps and found it, but selecting the uninstall button does nothing. I then tried installing Titanium Backup and after installing, Titanium Backup won't open and doesn't even show up in my app drawer. So, I'm a little stymied now. Unsure what to do next
Click to expand...
Click to collapse
Titanium Backup is going to be your best bet to do the uninstall process. When you selected update Flash from the market, then went and uninstalled it, you were only uninstalling the update. If TB installed, then it should show up in the app drawer of Zeam launcher. You can go into the market, and select to open it from there. Sometime it will not open on first attempt, because it is trying to ask you to give it root permission. If you still have trouble with it not opening, then uninstall it, and try to install it again. You can also open up the “Superuser” app to make sure that it has not been denied root permission.
TB definitely didn't appear in Zeam app drawer. I'm charging now and give it another shot in a bit.
Edit: Success. I got TB installed. I made a stupid error. I only installed the paid app, not the free also. I got Flash uninstalled and installed your Flash Fix.zip with numerous reboots with no boot loops.
GMPOWER, Thanks for your assistance
GMPOWER said:
For all future references, I have attached the working Adobe Flash fix file. It includes flash version 10.3.186.3, that was released today. It has been tested to work, and you can allow auto-update in the market without future problems.
Click to expand...
Click to collapse
I don't normally bump old threads, but this just saved me
Thanks a lot, I was at wits end figuring out why it was boot looping.
dreadwing said:
I don't normally bump old threads, but this just saved me
Thanks a lot, I was at wits end figuring out why it was boot looping.
Click to expand...
Click to collapse
Same here. Big thanks to GMPower! (My first post here, now I can use the Thanks button!)
Total noob question. This is my first time rooting. I got the root to work fine but updated Flash before finding out about the loop. I'm not sure what I'm supposed to do to fix this problem. OP in this thread said he reinstalled MN 4.6.16 via bootable SD with CWM and could get his nook to boot up. I tried that and rebooted but I'm still getting stuck in the loop.
Do I need to wipe my nook before reapplying MN?
dahcheet said:
Total noob question. This is my first time rooting. I got the root to work fine but updated Flash before finding out about the loop. I'm not sure what I'm supposed to do to fix this problem. OP in this thread said he reinstalled MN 4.6.16 via bootable SD with CWM and could get his nook to boot up. I tried that and rebooted but I'm still getting stuck in the loop.
Do I need to wipe my nook before reapplying MN?
Click to expand...
Click to collapse
Use the zip file in post #7 (in this thread). Drop it onto the same SD card you used to load MN 4.6.16. Put the SD card in and it'll boot to CWM....then flash that zip file the same way you flashed MN. Then, power off the NC, remove the CWM SD card and put in your regular SD and turn the NC back on. That should be it...no more boot loop.
I've got the same issue as the thread started and I downloaded the zip from post 7 and flashed it just like I flashed MN, but it's still boot looping. It gets a bit farther into the "Nook Color" logo but keeps repeating.
Boot Loops NC 1.3
GMPOWER said:
For all future references, I have attached the working Adobe Flash fix file. It includes flash version 10.3.186.3, that was released today. It has been tested to work, and you can allow auto-update in the market without future problems.
Click to expand...
Click to collapse
This problem started for me on Rooted 1.3. October 5th, Applied this fix.
Thanks GMPOWER
I figure I will explain my problem in more detail. I am working with my girlfriend's Nook trying to get it rooted. The first time I did she had 1.2 stock and I rooted it successfully. She updated flash not knowing that it would cause a boot loop. I had no idea how to fix it so she set it back to factory settings and procedded to update to 1.3 to see if that would solve the boot loop. I rooted it again and it started boot looping again. I found this thread and the flash fix. I flashed it onto the Nook and it fixed the loop problem.
Well she found out that the marketplace has limited visibility with 1.3 and wanted to go back to 1.2 to have her full visibility back. So she factory reset it again, I rooted it again and it started boot looping again. This time though the fix from post 7 isn't helping. I flash it and then reboot and it loads the "Nook Color" logo once fully and then stops and starts it over again and gets stuck at "Nook Col".
Is there anyone who might be able to help me with what the problem is, or am I gonna have to reset it back to stock, use Titanium Backup to remove flash and then use the zip from post 7? I know that it's not a root problem because I successfully rooted my mom's Nook before my girlfriends and her's is working fine.
Followed your instructions and my problem solved, many thanks!
johnny15 said:
Use the zip file in post #7 (in this thread). Drop it onto the same SD card you used to load MN 4.6.16. Put the SD card in and it'll boot to CWM....then flash that zip file the same way you flashed MN. Then, power off the NC, remove the CWM SD card and put in your regular SD and turn the NC back on. That should be it...no more boot loop.
Click to expand...
Click to collapse
my first post. thanks GMpower
just had this happen to me too. I've tried the flash update, and I get slightly more of the nook color boot graphic but it still hangs.
any thoughts?
Since the screwy Youtube update won't work with 7.0.3.encore and read it was working with nightly 151 I decided I wanted to try to install a newer version. Following the directions I have read on the forums, I downloaded the newest nightly 155 and placed it on the boot folder of the SD. Then I selected boot device: sd and recovery, but it just hung at the boot menu screen. I let the NC sit for about 10 min to see if it was doing anything (it wasn't) and then had to do a power off-N.
I changed back to the standard boot file, restarted, then from cm7 rebooted into recovery. CM7 started normally and still didn't apply the update.
What am I doing wrong?
Imbroglio said:
Since the screwy Youtube update won't work with 7.0.3.encore and read it was working with nightly 151 I decided I wanted to try to install a newer version. Following the directions I have read on the forums, I downloaded the newest nightly 155 and placed it on the boot folder of the SD. Then I selected boot device: sd and recovery, but it just hung at the boot menu screen. I let the NC sit for about 10 min to see if it was doing anything (it wasn't) and then had to do a power off-N.
I changed back to the standard boot file, restarted, then from cm7 rebooted into recovery. CM7 started normally and still didn't apply the update.
What am I doing wrong?
Click to expand...
Click to collapse
What does that mean?
What is the standard boot file? and what did you do b4 changed back?
I am using the multi-boot that allows you to select from sd or emmc.
Got it.
Since I don't do "dual boot" so I have no experience, can't help much here, m8
I'm sure others will help you.
OK, so I bought a new Sandisk 16GB Class 4. I just figured I'd build up from scratch. Went and flashed the new CM7.1 stable, everything was fine. Enabled WiFi, configured it, turned it off. Put GAPPS on the boot partition, rebooted into recovery, it flashed GAPPS fine. Rebooted normal - and it stuck at the spinning skateboard logo.
Thought, "I musta dorked something up".
This time, reimaged the card, flashed CM71 and GAPPS at the same time (verygreen's size agnostic does CM7, then looks for GAPPS and does that next).
Same thing, gets stalled at the skateboard logo.
So - something with this combination of card, CM71, and GAPPS is flaking out on me and not going anywhere. If I *just* put CM71 on it, everything is fine. If I try to put GAPPs on it, it freezes at the boot logo. I tried the most recent, and the June version of GAPPs, too.
Any ideas?
Suggestion: do one at a time (just re-do your first procedure), if it hangs on boot, force shut down and power back up again and see what happens.
votinh said:
Suggestion: do one at a time (just re-do your first procedure), if it hangs on boot, force shut down and power back up again and see what happens.
Click to expand...
Click to collapse
It wasn't any better. I ended up rebooting a few times before installing gapps and that seemed to work. I am back up and running.
Sent from my NookColor using xda premium
Glad it's up and running now.