Related
So, I have an 8525, newest rom from Cingular/HTC, and a few apps.
The apps I am running are as follows:
SPB Pocket Plus
SPB Mobile Shell
SPB Diary
VibraSwitch
Device Lock
Jetware BT Fix
Clear Temp
and a few other irrelevant ones.
Anyways, I have the Device Lock mapped to the Comm Mgr button. So, I lock the device, and power off the screen. When I go to wake up the device, Instead of the usual unlock in the bottom right of the screen, first I get Password, so I hit it, then I have to hit unlock, then unlock again as normal....
Any suggestions? I have never set a password on this device, so I dont know why all of a sudden it is prompting me for it.
Thanks,
John
Same thing happened to me when I installed Shell on my touch.
that's wierd. I had the trial version for a while, then got the full version, and only started with the full version. Never happened when I had the trial version.
Do a so called hard reset:
Press and hold the Left SOFT KEY and Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom of your device. You will be presented with a menu saying 'press R to reset, X to exit', if you press R Your device will be set back to factory default settings.
(The L/R soft keys are the "--" keys just up the start and OK buttons)
This should do the trick!
Hermes 100 (8525 Cingular) (WM6 Flashed) Won't except PASSWORD
Hi all! I'm a new member here so the help is greatly appreciated.
So here's the deal. I just recently got married while doing the last minute prep for the big day my hermes 8525 decides to get devil possesed on me.
It started a few days before. Sometimes losing radio connection and other times locking up right after a call was completed but not fully ended. It was OK I guessed since I was able to powerdown and restart (remove the battery) and resume "normal" use.
BUT on the day before the wedding, That lil @#$% decides to lockup one last time and after a power down (removing battery) and restarting the unit, I was prompted to enter the password (as usual), BUT this time after entering my password for access, like I always do, I got the response stating that my password was not entered in correctly. AAAARRRRRGH! NO WAY! but yes way. The worst has struck.
After searching my ARSE off looking for a solution the best I came acress was a "hard reset". Another AAAARRRRGH!
From what I understand this would wipe off all my data. This would really hurt since I had recently entered many long lost (over 10 years) family members contact info that I was finally able to track down.
So, I'm reaching out to this community for something... anything that would HELP!!!
How can I get into my phone and get my contacts back???
TIA
I really appreciate any help on this one!
NEAR TEARS!
Still Stuck
THanks for the replies and the suggestion for the HARD RESET which I'm finding very hard to DO! Not that I can not just that I CAN"T!
I've been talking with an HTC tech in the hopes that this issue can get a better resolution than NUKE'n all my data. Didn't hear from him last night, guess he's still diggin for a solution. I'll have to call him in the morning. Hopefully he has figured out something.
Thanks Again ALL!!!
Hi all,
I have had loads of problems with this phone, so I decided to do a factory reset.
It rebooted as normal until it got to the Motoblur setup page
It asks for the Motoblur details to be entered, but once you have entered them and pressed the 'next' button, it goes back to the previous screen instead of the next step and then gets stuck in a never ending loop.
I've tried skipping the sign in process but instead of skipping it, it just goes back to the first Motoblur account setup screen instead.
Out of desperation, I have tried to make several new Motoblur accounts but every single time, it gets to 80% completion, then stops.
I have even left running all night (plugged in) and it still freezes at 80%
I can't do another factory reset because it won't get past the Motoblur setup screen.
I've tried to do a hard reset by holding x and powering the phone on but this doesn't work. It just brings up the triangle and android robot but it does not go to the next step despite me leaving it for several minutes.
Only had it for 7 weeks and am awaiting a response from Expansys on what to do.
Any help from you guys will be greatly appreciated.
Apply a debrand image of your system and do a full wipe
phorenzik said:
I've tried to do a hard reset by holding x and powering the phone on but this doesn't work. It just brings up the triangle and android robot but it does not go to the next step despite me leaving it for several minutes.
Click to expand...
Click to collapse
Have you pressed the @ key when you get to this step with the robot and the triangle? That should bring up the reset menu, and then you use the volume and camera buttons to choose and select the option you require.
Cheers,
Steve.
StevePritchard said:
Have you pressed the @ key when you get to this step with the robot and the triangle? That should bring up the reset menu, and then you use the volume and camera buttons to choose and select the option you require.
Cheers,
Steve.
Click to expand...
Click to collapse
I didn't know you had to press @
Thanks
I've done a hard reset, but I still have the exact same problem.
If I try to input my proper Motoblur details it instantly says connection failed (it doesn't seem to even try to connect as fails the instant you press 'next)
Creating a new account hangs at 80%
Any more ideas before I throw it against a wall?
I notice there was an option to boot from SD in the recovey mode.
Would this allow me to boot an official motorola rom?
If so, where would I get the rom from?
A walkthorugh on exactly how to do this would be appreciated if this method could fix my issues.
I'm really annoyed because I sold my HD2 for this phone and I'm regretting it.
Thanks
phorenzik said:
I didn't know you had to press @
Thanks
I've done a hard reset, but I still have the exact same problem.
If I try to input my proper Motoblur details it instantly says connection failed (it doesn't seem to even try to connect as fails the instant you press 'next)
Creating a new account hangs at 80%
Any more ideas before I throw it against a wall?
Thanks
Click to expand...
Click to collapse
I think you need internet connection in order to validate your account or create a new one. Check your APN settings first, or do it on wifi.
Hi,
I've tried it whilst connected to my wifi router. I've even tried it via the data connection but nothing happens.
It seems that despite the data/wifi connections being there, it just ignores them.
I think this is the issue. It's not connecting and I don't know why
The phone displays the wifi/3G data symbols in the task bar but it doesn't seem to be using them during the Motoblur setup
Mine is dead too!!!
Hello everybody,
Greetings from sunny, flooded, blown away, Queensland Australia!
Long time lurker, first time poster...
I have a...
Vodafone-Australian-2.2-Milestone2
2 weeks old and its an expensive paper weight. It was rooted and thats about it, had a bunch of root required apps on there, installed the bootstrap, but hadnt installed Xrecovery yet.
I was playing around the other day. changing settings, installing and uninstalling a heap of apps, testing them. Some app suggested I restart or it restarted itself, cant recall, and that was the end. Boots until it gets past the M, and then its just bootloop city.
Won't register on comp in RSD or anything. Will boot to stock recovery and cleared cache and data several times, but that didnt fix anything. Won't even charge the battery. It will run an update but has to be signed. Problem is, we havent had any updates yet on these phones in Australia and there are no custom roms. What update.zip could I get to try to fix it, because I think thats about my only hope.
While recovery was wiping the data and cache it would stop frequently and each time I would touch the ok in the bottom corner of the screen and it would continue, and seemingly despite the 10 or more stops, completes fine. Surely thats not normal.
Out of ideas, I would just send it back with a story but the vodafone boot animation is replaced with disco flashing lights. and thats all it does, non-stop. Do you think they will notice someone has been tinkering?
Ideas? Thoughts?
Oh, and forgot to mention, when I first got it I had the same problem with the Motorola sign in wizard on startup, for quite a while, cant remember how I got around it though. Stop trying to sign in and just get out of that wizard, install ADW Launcher or similar and dont go near any Moto apps. You are only required to do a Gmail sign in, not Moto.
That's the problem though.
I'm stuck at the Motoblur sign in and it will not skip.
Whenever I select skip, it just goes back to the motoblur sign in page instead of going to the home screen.
Basically, in a nutshell, this is what's wrong:
I can't sign in to motoblur (gets stuck in a loop)
I can't create a new motoblur account (crashes at 80% every time)
I can't skip the sign in process (takes me back to the motoblur sign in page instead of loading home screen)
This is my first and last Motorola phone. Not good at all.
So what happens if you press press home or back repeatedly instead of skip? And if all fails reflash new SBF
benking1972 said:
So what happens if you press press home or back repeatedly instead of skip? And if all fails reflash new SBF
Click to expand...
Click to collapse
It just goes back to the motoblur setup/signin screen no matter how many time I press home, back or skip. It's as if a dll is missing and it's unable to boot to the home screen.
How do I flash a new SBF?
Motorola have agreed to let me return it but if I can do it myself I'd rather do it.
I have found this guide http://forum.xda-developers.com/showthread.php?p=11155476#post11155476
but the link to the UK SBF is dead
Yeah, that's the one, and the link to UK SBF works fine for me. If you can't get it to flash that way, then you are going to have to do it the way I am about to do mine, which is...
http://forum.xda-developers.com/showthread.php?t=804088
Failing that, send it back and be done with it.
since its so new id send it back. you shouldnt be having this problem at all. the milestone 2 is a very solid phone. i had mine running for 90 days straight not even a reboot or crash or anything lol. sounds like you just got a duff one. with any piece of technology theres bound to be a few that slip through the net. even if you find a fix for your problem you dont know what is causing it. and if youve had problems before then somethings obviously wrong. since theyve agreed to let you return it then thats your best option.
Probably i should send mine one back as well.
Bought a new Milestone 2 yesterday (from ebay, Chinese guys but as per retail package phones are for UK market). Put the SIM in just to check before wiping out everything from my old Defy. Made a call, checked the version and the menu and put the SIM back to Defy to backup all I needed. Plugged Milestone to the mains. 3 hours later found promising "Fully charged" on the screen and put the SIM in. That was it... Since I can't power the phone whatever I do. I thought the Power button went off as I tried to perform hard reset (x+Pwr), BRM (Arrow up+Pwr) and nothing happent at all. But then I put the phone on the charger again and the Power button worked fine switching the screen off and back on.
Any other methods to get the phone running?
UPDATE: It's strange and weird, but I've just had an idea to remove SD card and it worked - the phone powered on immediately!! Formatted the card using card reader, put it back - the phone works flawlessly. Fantastic! =))
Have a nook color, cm7 - screen will not light. Power will cut on and off (i can tell because volume buttons produce noise when on). Screen gives no illumination when on.
Nothing software or programming updated or changed that would have caused it. I've charged it overnight and attempted to cut on while plugged in.
Plugged back into laptop via USB and I can see (nook color icon with yellow exclamation point) but still no screen.
I'm at a loss. Searched all posts but cannot find one similar. Thx!
I know that this happens and is fixable, although I cannot remember where I saw the "official" fix. If you have nandroid backups on a SD card, you could hard reboot the nook with the 8x reboot, and then reflash CWM and restore your backup.
Are you willing to lose your data and temporarily revert to stock?
I'll give anything a try.
Thanks for the idea. I'll try this in the morning and repost. I had thought about hard booting and taking it back but was worried they wouldn't replace it since it had been rooted. I'll go back and research the steps you mentioned. I'm not a techie so it will take a fresh mind and some coffee to pull it off. I was beginning to think it was a bad screen.
Power off nook, and power it back on. As soon as it begins to load, press n, power, and volume+ (I learned it with both volume keys, but I just heard it may only need the +) and hold for about ten seconds. The nook will flash off, release buttons. The nook will automatically restart, so after you release the keys, you want to repress them gain right as it starts to boot (where you would normally see the cyanogen logo). After the eigth time it will load into froyo firmware. If you. Misstime the sequence you will need Ronstadt over, so if it doesn't work the first time, just try again. Maybe a dark room, so you can see the slight illumination somewhat.
Bad screens do happen, I suppose, but the nook is unbrickable from a software standpoint. The primary boot is off the sdcard, so there is always a way to circumvent or preempt anything that may be corrupted internally. If you were to have a bad screen, after you hard reboot the nook, it will load the stock OS, but if you flashed CWM internally that will still be in your emmc. The way to get rid of the CWM is to follow the hard reboot with a factory reset through the froyo menu (standard nook OS for any future readers). If your screen is indeed bad, you can take your chances that they wont notice since they are replacing an obvious hardware issue, or you could hold it next to a working nook and base your touches approximately off that. There aren't that many steps, but you.do have to go through the B&N registration process, and your user name and password would be a *****.
I might just hard reboot and roll the dice myself, although I haven't personally heard of a bad screen yet. Good luck.
Solution worked!!
Thanks so much.....I couldn't get the 8x to work because the screen was not on and I couldn't time it right. The only way I could tell if it was on or off was with the power button making noises. So I held down power and N button together until flash. After the flash the cm7 open screen popped up. woot woot. and many thanks but I can only push the button once.
Hello all, I'm curious to hear your thoughts and advice.
My nook is completely unresponsive. It is not stuck at rooted forever.
In fact this has nothing with a root attempt/reset/restore/power on.
I had done a a fresh reset/root with touchnooter about four months ago and was happily and smoothly reading for about two months. I then got busy and put the nook down, did not touch or use for about another two months. I tried to use it about a week ago but found that it had run out of battery in sleep after the two months of disuse (not surprising). I put it on charge overnight and everything booted right and functioned well once it turned on, except that the battery indicator in the statusbar showed a "?" and the battery info in system info showed 100% "unknown". After alot of fruitless research I put it down with the intention of reset/restore/root when I had the time.
I just picked it up this morning and was faced with the expected "Press then button below to wake up your NOOK" screen. But when I pressed the "n" button nothing happened. Obviously holding the "n" did nothing as well.
I tried to power it off and on- nothing
holding power for 20- nothing
power for 30- nothing
8 failed boots- nothing
left right- nothing
left right power-nothing
random pushing and holding of power- nothing
all these with mem card in and out- nothing
all these plugged usb- nothing
all these pugged ac- nothing
I let it charge some more- nothing
None of the buttons do anything, the screen stays inevitably at the " press the n button to wake" screen. no activity whatsoever except that when It is plugged in, the green light shows. NO ORANGE LIGHT... it is fully charged by both usb and ac.
It is not detected at all by windows anywhere.
In Linux- lsusb, bklid, and df -h yield nothing. My nook might as well be the invisible stupid ereader.
I did not drop it, sumbmerge it, perform magic around it... It has been sitting on a shelf doing nothing.
To repeat, the only thing my nook does is light up green when plugged.
It is unchangeably stuck on poe's face...
If this isn't true brick, I don't know what is.
I'm exhausted. Any ideas? I appreciate the help.
Best,
Thomas
i don't know. i just know my dog ate mine and i'm now in the market for a new screen, so if you don't get it working sell me the unit and get some money for yourself to purchase a new one =D
or you could google the disassembly instructions and try unplugging the battery, not very hard to do. could be of .. some help perhaps?
I would definitely take you up on your offer, but i'm still under warranty.
However, I would still like to have my original, and figure out what is going on and why it happened.
Ideas?
Thank you.
similar problem were solved
Hi! I might have read about similar problem solved on USB host mode here http://forum.xda-developers.com/showpost.php?p=23475998&postcount=131
That's it, thanks so much.
if it help
if it helps let them know in the tread that you had same problem. they are wondering whether it is due to host mode
[N2E]: After automatic update to 1.1, Nook Touch Screen absolutely DEAD--Nothing Work
THIS WAS A POST FROM ANOTHER SITE AS TO MY PROBLEM:
I was reading on my N2E last night. I put it down for about 30 minutes and when I came back it was displaying the default "Authors" screensaver (I had switched to the Nature photos) and asking to slide to unlock. I thought, "Oh, the new software update must have downloaded and installed. I'll check it out." To my shock, the touch screen was completely unresponsive--no amount of swiping would unlock from the screen saver. I let it set for a while longer thinking perhaps the softare update was not yet finished. No such luck.
As a result of the new update, my NOOK is now completly DEAD! I tried powering off, but couldn't do that because you are asked to confirm power off on the touchscreen, which no longer works. So, I looked online and tried the soft reset/reboot by holding down the "Home" or "n" button and then pressing the power button for several seconds. Great--it started rebooting...and came right back to the "authors" screen saver and asking to swipe to unlock. I tried this rebooting process several times, always with the same result: back to screeensaver mode with completely unresponsive touchscreen.
So, looked at the online technical troubleshooting discussion and helps and decided to try a downloaded manual install of the software update. Plugged my NOOK into my computer and it recognized it. So, I downloaded the manualo software update and dragged and dropped it onto the NOOK as directed and sure enough, it started to reboot itself. I thought, "whew, maybe this will fix it". NOPE--came right back to the locked screensaver, with no mention of attempting to update software, and the touchscreen is still dead. (By the way, all of this was done initially with the NOOK showing about 94% charged, so it was not a battery issue.)
Reconnected the NOOK to my computer and the software update file was gone from its home directory, which implies it did something with it. So, I tried repeatedly to install the software update manually, always with the same result: NOOK comes back to locked default "authors" screensaver wtih a dead touchscreen.
Looked online for B&N technical support again saw that others had this problem (though only found a couple references). Found the instructions to do a factory reset and reluctantly tried that, desparate to make my NOOK work again, but frustrated that if it did I would have to rebuild everyting on it and download my 400+ B&N book library all over again. But, guess what, factory reset just comes up to the "Welcome to your all-new NOOK" screen (sounds like progress), BUT the touchscreen is STILL dead, so I can't hit the "Next" button onscreen to proceed with setting up my factory-reset NOOK. Tried rebooting again (as this seems to be the only solution offered in the online tech support) and now it just keeps coming back to the "Welcome to your all-new NOOK" screen with a dead touchscreen keeping me from doing anything.
So, now I am taking it back to my local B&N store in hopes they will exchange it for a new NOOK.
I really want to see a feature to disable automatic updates in the future. I specifically didn't download and manually install when the update came out, figuring I'd wait for the automatic download to give time to B&N to work out the bugs and perhaps issue a patch (as they have done in the past for the N1E). Instead I get no warning about the automatic download (happens while I am reading and set the NOOK aside for 30 minutes), and then the update KILLS my NOOK.
I am not a satisfied NOOK customer at this point.
MY POST: (from the that site)
Not Sure how to do this post or whatever, but I was happy until the update and everything that happened to you is the same with me. This is the first post that describes what happened to me. I'm out of warranty and refuse (and can't) to buy another one of these. If their updates can do this, I'm not sure I want to sink another $100 into the shareholders pockets. I'd really like to know if anyone knows what may be wrong with it.
In addition to what was already mentioned, I took the battery out several times(which seems intimidating but very easy but voids the warranty) and took it completely apart cleaning the screen very well with water and another time a glass cleaner. I tried rooting also. Not sure of what to do now. It seems software related due to working fine until the update. Still at the "Welcome to your all-new NOOK" screen with unresponsive screen. I wasn't sure if the last sentence from B&N was a personal message to me welcoming me to the "new" state of the my nook.
Thanks for any help from anyone.
Thanks.
Identical problem.... and no fix..
It is a shame you got no solution for this. and the worst, you are not the only one... it happened exactly the same with my Nook ST....
Hopeless...
Machiavelli_The_Man said:
THIS WAS A POST FROM ANOTHER SITE AS TO MY PROBLEM:
I was reading on my N2E last night. I put it down for about 30 minutes and when I came back it was displaying the default "Authors" screensaver (I had switched to the Nature photos) and asking to slide to unlock. I thought, "Oh, the new software update must have downloaded and installed. I'll check it out." To my shock, the touch screen was completely unresponsive--no amount of swiping would unlock from the screen saver. I let it set for a while longer thinking perhaps the softare update was not yet finished. No such luck.
As a result of the new update, my NOOK is now completly DEAD! I tried powering off, but couldn't do that because you are asked to confirm power off on the touchscreen, which no longer works. So, I looked online and tried the soft reset/reboot by holding down the "Home" or "n" button and then pressing the power button for several seconds. Great--it started rebooting...and came right back to the "authors" screen saver and asking to swipe to unlock. I tried this rebooting process several times, always with the same result: back to screeensaver mode with completely unresponsive touchscreen.
So, looked at the online technical troubleshooting discussion and helps and decided to try a downloaded manual install of the software update. Plugged my NOOK into my computer and it recognized it. So, I downloaded the manualo software update and dragged and dropped it onto the NOOK as directed and sure enough, it started to reboot itself. I thought, "whew, maybe this will fix it". NOPE--came right back to the locked screensaver, with no mention of attempting to update software, and the touchscreen is still dead. (By the way, all of this was done initially with the NOOK showing about 94% charged, so it was not a battery issue.)
Reconnected the NOOK to my computer and the software update file was gone from its home directory, which implies it did something with it. So, I tried repeatedly to install the software update manually, always with the same result: NOOK comes back to locked default "authors" screensaver wtih a dead touchscreen.
Looked online for B&N technical support again saw that others had this problem (though only found a couple references). Found the instructions to do a factory reset and reluctantly tried that, desparate to make my NOOK work again, but frustrated that if it did I would have to rebuild everyting on it and download my 400+ B&N book library all over again. But, guess what, factory reset just comes up to the "Welcome to your all-new NOOK" screen (sounds like progress), BUT the touchscreen is STILL dead, so I can't hit the "Next" button onscreen to proceed with setting up my factory-reset NOOK. Tried rebooting again (as this seems to be the only solution offered in the online tech support) and now it just keeps coming back to the "Welcome to your all-new NOOK" screen with a dead touchscreen keeping me from doing anything.
So, now I am taking it back to my local B&N store in hopes they will exchange it for a new NOOK.
I really want to see a feature to disable automatic updates in the future. I specifically didn't download and manually install when the update came out, figuring I'd wait for the automatic download to give time to B&N to work out the bugs and perhaps issue a patch (as they have done in the past for the N1E). Instead I get no warning about the automatic download (happens while I am reading and set the NOOK aside for 30 minutes), and then the update KILLS my NOOK.
I am not a satisfied NOOK customer at this point.
MY POST: (from the that site)
Not Sure how to do this post or whatever, but I was happy until the update and everything that happened to you is the same with me. This is the first post that describes what happened to me. I'm out of warranty and refuse (and can't) to buy another one of these. If their updates can do this, I'm not sure I want to sink another $100 into the shareholders pockets. I'd really like to know if anyone knows what may be wrong with it.
In addition to what was already mentioned, I took the battery out several times(which seems intimidating but very easy but voids the warranty) and took it completely apart cleaning the screen very well with water and another time a glass cleaner. I tried rooting also. Not sure of what to do now. It seems software related due to working fine until the update. Still at the "Welcome to your all-new NOOK" screen with unresponsive screen. I wasn't sure if the last sentence from B&N was a personal message to me welcoming me to the "new" state of the my nook.
Thanks for any help from anyone.
Thanks.
Click to expand...
Click to collapse
The factory restore does not actually fix every possible problem with your Nook.
If your Nook responds at all, try to boot it up on an SD card like ClockworkMod or noogie.
At least that way you can see what is happening.
The partitioning might have become corrupted which the "factory restore" does not touch.
If no response with anything, try disconnecting the battery.
You might also try booting over USB using the techniques in rooting the new white glow.
Hello I was wondering if I'm just screwed I bought 2 nook simple touch, one for me and one for a present to my mother for her birthday on march 16. I bought them at best buy for $40 a piece on January 30. I used mine and was perfect but when I tried to set up my mom it wouldn't load the license agreement, always got stuck or reboot or something, so I loaded cwm on an sd card just to play around, tested on my nook and was fine, then put it on my moms nook booted once then I didn't press anything and turn it off then I load the image but when I tried to boot again it got stuck on the load screen and wont do anything, no reset sequence will work with the sd card on or off the other nook boots with this sd card. at the end I exchanged with my mom she is happy with her nook an I have a useless unit do you think they will exchange it I didn't rooted it or did anything to it but has the n cwm splash on screen forever. I'm in Costa Rica right now and wont return home until May do you think I'll might be able to exchange it or should I just try to repair it.
I'm glad that your mother got the working one!
You say that that one will boot on your CWM SD card, but yours won't?
It may be hard to get your unit exchanged with a conspicuous screen on it, even if it's not your fault.
When you plug it into your desktop is there any indication of a new USB device found?
If it's charged and no amount of the power button gets a reaction, I'd open it up.
any news???
Hi endor43, same problem here, have been able to find any solution?
endor43 said:
Hello all, I'm curious to hear your thoughts and advice.
My nook is completely unresponsive. It is not stuck at rooted forever.
In fact this has nothing with a root attempt/reset/restore/power on.
I had done a a fresh reset/root with touchnooter about four months ago and was happily and smoothly reading for about two months. I then got busy and put the nook down, did not touch or use for about another two months. I tried to use it about a week ago but found that it had run out of battery in sleep after the two months of disuse (not surprising). I put it on charge overnight and everything booted right and functioned well once it turned on, except that the battery indicator in the statusbar showed a "?" and the battery info in system info showed 100% "unknown". After alot of fruitless research I put it down with the intention of reset/restore/root when I had the time.
I just picked it up this morning and was faced with the expected "Press then button below to wake up your NOOK" screen. But when I pressed the "n" button nothing happened. Obviously holding the "n" did nothing as well.
I tried to power it off and on- nothing
holding power for 20- nothing
power for 30- nothing
8 failed boots- nothing
left right- nothing
left right power-nothing
random pushing and holding of power- nothing
all these with mem card in and out- nothing
all these plugged usb- nothing
all these pugged ac- nothing
I let it charge some more- nothing
None of the buttons do anything, the screen stays inevitably at the " press the n button to wake" screen. no activity whatsoever except that when It is plugged in, the green light shows. NO ORANGE LIGHT... it is fully charged by both usb and ac.
It is not detected at all by windows anywhere.
In Linux- lsusb, bklid, and df -h yield nothing. My nook might as well be the invisible stupid ereader.
I did not drop it, sumbmerge it, perform magic around it... It has been sitting on a shelf doing nothing.
To repeat, the only thing my nook does is light up green when plugged.
It is unchangeably stuck on poe's face...
If this isn't true brick, I don't know what is.
I'm exhausted. Any ideas? I appreciate the help.
Best,
Thomas
Click to expand...
Click to collapse
There are times when a Nook gets in a mode where it won't accept a charge.
Opening it up and disconnecting the battery for a minute might fix this.
endor43 said:
That's it, thanks so much.
Click to expand...
Click to collapse
When this worked for you did the light turn orange right when you plugged the battery back in? I just took the battery out, plugged the nook into a charger, and with it plugged in plugged the battery back in and the light stays green the whole time yet I'm not able to use the nook at all.
My nook second generation is not responding to my touch I tried everything to get it to work and I eventually got it to completely power of what if it does not work when I turn it on what should I do
It could be power/battery problems.
Check to see if it makes itself known when the USB is plugged in.
If it reacts at all, that's an indication of life.
I rooted the Nook a while back and wanted to go back to a stock experience, so I rebooted it the six or eight times to get it to restore. However, when I did so, I could still get in to the ADW launcher that was installed. It began updating automatically shortly thereafter and has been stuck on the "Installing" screen. Nothing I have done has helped at all including:
- Charging the Nook
- Holding the power button
- Holding the power button and the bottom page buttons
- Holding the power button and the Nook button
- Holding the power button for sixty seconds, followed by holding the power and Nook buttons for sixty seconds (as per B&N support instructions)
- Removing the battery
When I called B&N support, they told me it was dead and they would replace it if it were within warranty, but it is not and I have obviously opened it up to remove the battery, so that probably wouldn't work anyways. It seems like the computer detects something when I connect it, but it does not show it as a storage device or anything.
Maybe someone here who is a bit more savvy can help me with this because I would have really liked to give this as a Christmas gift to my mom.
Also, my wife has a Nook with Glowlight and has just noticed a small crack in the screen. I recently had to open up the device to reseat the plastic around the USB port because the case popped it out when she removed it one time. Now, obviously, I opened it up, but I want to try to use the warranty to get the screen fixed. Any advice on getting B&N to honor the warranty or somewhere I can find the T5 screws with the sticker still on them or a cheap screen replacement. I didn't do anything to the screen, so it wasn't anything I did that caused this issue.
THANKS FOR ANY HELP!
You'll probably need to put together a clockworkmod micro sd card, and use it to install the latest update over your current system.
Once you're up and running, your apps will still be installed. The update doesn't touch /data. It'll just revert your /boot and /system partitions to stock. I'm not aware of an easy way to revert that without using a backup that you (should have) made before doing any modifications. As far as I know, you have to uninstall those apps manually (using adb if you have to).
Thanks for your response.
The big issue is that it won't budge from the installing screen. Once it gets off of that I could try, but as I said before, I think I have tried everything...