Hi,
I tried to upgrade from v2.1 to new Android 2.3.5 Gingerbread For LG Optimus GT540 and I followed instructions exactly, but I am stuck at number 8, I did this:
8- Now click “Launch software update”, DO NOT USE THE PC TO THE PROCESS IS COMPLETE. THE PHONE WILL REBOOT WHEN FINISHED THE PROCESS IN KDZ. (The process takes about 15 minutes in KDZ).
and about 2 minutes text log writes and stopped, I am now waiting more then 40 minutes my phone didn't reboot. On display is still written download mode, what should I do now ?
In kdz is written:
3GQCT: wParam = 205. IParam = 36
p.s.
I disconnected phone from usb and pull out battery and now I cannot turn on phone, I tried to push vol down + power for 5 sec.
Any idea what should I do now? I hope I didn't brick my phone
What programs are you using?
What are you using to update your phone and have you tried taking out your SIM, SD card and battery then turned it on with the USB cable?
I used KDZ updater and tried to install CyanogenMod7 (2.3.5) @ GT540 Swiftdroid2 RC3 by Mur4ik. if that is what you ask ?
I removed sim card and battery also, then tried to turn it on while plugged in to computer usb but no response from phone, I can't turn it on
p.s. I am using win 7 64 bit OS
gorantz said:
I used KDZ updater and tried to install CyanogenMod7 (2.3.5) @ GT540 Swiftdroid2 RC3 by Mur4ik. if that is what you ask ?
I removed sim card and battery also, then tried to turn it on while plugged in to computer usb but no response from phone, I can't turn it on
p.s. I am using win 7 64 bit OS
Click to expand...
Click to collapse
If you can't get into download mode, then it's game over I'm afraid. What you will need to do is return the phone back to where you bought it. This happened to me some time ago. But the Carphone Warehouse were happy to fix it (even though I had voided the warranty but don't tell them that ). Don't say that you tried to mod the phone, say something like 'I installed LG's PC Suite and it said my device had a software update. I went along with it, but it gave me an error half way through. Now my phone won't turn on at all' It might just work!
I had the same problem when modding with kdz.
completely bricked my phone, but was able to fix by putting kdz into emergency mode instead of diag and updating with a fastboot stock rom,
it would stop after 2 minutes and give me and error but it managed to get fastboot onto my phone,
(camera + power)
then just flashed the fastboot method with adb and everything was fine,
my problem was something to do with lg modem drivers i believe,
I read a thread that said to disable the lg virtual modem. (didnt
work for me)
pretty noob myself
but the above method worked for me,
not sure if this can do anymore damage to the phone
have a look at this is u get it into emegancy mode.
On the kdz updater instead of 3GQCT put into emergancy
http://www.youtube.com/watch?v=fDmU9RSIiDA
If you have tried flashing with Cm7 you might be lucky,
try holding camera button and powering on the phone, a black screen should come up thats fastboot.
if that comes up u should be able to just reflash following mur4iks instruction
if not try what i said in my last post and reflsh with phone type 3QGCT and PhoneMode EMERGENCY
again only going of how i fixed my bricked phone
ZxWelshyxz said:
If you have tried flashing with Cm7 you might be lucky,
try holding camera button and powering on the phone, a black screen should come up thats fastboot.
if that comes up u should be able to just reflash following mur4iks instruction
if not try what i said in my last post and reflsh with phone type 3QGCT and PhoneMode EMERGENCY
again only going of how i fixed my bricked phone
Click to expand...
Click to collapse
He was trying to flash a fastboot rom (to install CM7) but bricked his device in the process. So he can't flash CM7-.-
Yeah I know that but I mean when I got the error he has, I flashed with a stock 2.1 fastboot rom With Diag changed to EMERGENCY and was able to get on to fastboot mode (camera+power), I got the error again as i was flashing but the phone would load fastboot and not start up
If he can get lucky and get into fastboot like i did, a simple:
fastboot -w
fastboot flash boot boot.img
fastboot flash system system.img
fastboot reboot
should fix his problem or did i just get lucky?
sorry if im confusing thinks here, but this is how i fixed mine. which was also dead and not turning on
Sent from my GT540 using XDA App
@ZxWelshyxz
I am total neewbie, can you write to me some kind of tut, like press that then do that etc
gorantz said:
@ZxWelshyxz
I am total neewbie, can you write to me some kind of tut, like press that then do that etc
Click to expand...
Click to collapse
Well like i told you im a noob at this myself (Android phone flashing atleast)
I suppose it would be good to see if you got fastboot??
Power on the phone while holding camera button (hold the camera button until the screen goes black) if you can get fastboot you can just follow the fastboot flash instructions after fastboot -w
if not on kdz in the top right were it says DIAG, Change this to CS_EMERGENCY,Click Launch update and flash again with a stock fastboot rom
after THIS see if the phone loads or boot loops(had this once too) or loads fastboot
Il try look to find the thread i read on another forum for troubleshooting kdz it helped me alot
EDIT: http://android.modaco.com/topic/321895-faqgt540-reference-thread/ try some of the troubleshooting tips at the bottom of the O.P
I basicly aimed to get fastboot working so make sure your flashing with a stock FASTBOOT! rom
again im new to this im just saying what got my phone back to life
my fone stuck in download mood what can i do?
corecrack said:
my fone stuck in download mood what can i do?
Click to expand...
Click to collapse
Pull out the battery and turn on the phone again (if you have knocked the phone when turning on, or flash a KDZ (when connected to PC)
@gorantz
Can i advise to follow step by step tutorial pin pointed by lavero.burgos, am a total neewbie like u man,but now using latest CM7 by Mur4ik and waiting for new release from devs
Sent from my GT540 using XDA App
thanks, but my phone is now at service when I get it back maybe I'll try....but maybe
gorantz said:
thanks, but my phone is now at service when I get it back maybe I'll try....but maybe
Click to expand...
Click to collapse
I bricked my phone and I tried it again after getting it back from lg
I'm new here and to having a Smartphone, I've just been given an LG Android GT540 which is at version 1.6. The LG site tells me I can upgrade to 2 something or other, sorry can't remember the exact number and gives instructions on how to do the upgrade, but I'm a bit on the cautious side as I don't want to brick it, not this early on in owning my first Smartphone.
I'll be reading a lot of the posts here to try and find out as much as I can before I attempt to do this.
Well don't worry if it's official update. But if you some how brick your phone just tell lg the update bricked your phone and we are talking about unofficial updates
Sent from my GT540 using XDA App
gorantz said:
thanks, but my phone is now at service when I get it back maybe I'll try....but maybe
Click to expand...
Click to collapse
Dont hesitate to ask for help man its worth upgrading.
Sent from my GT540 using XDA App
I've got phone today from service (not official LG service), repairman just manage to wake up phone so I can turn it On, but when I turn it I get black screen with message on it ''download mode''. Now computer recognize phone when I plug it, and I tried to update or flash it with kdz updater but have no luck
I launch kdz in emergency mode, load rom with updater, press launch button, and process started, (get messages unpacking software etc.) but after 3-4 minutes I notice that computer is blocked I couldn't do anything with mouse pointer, and I waited 15 minutes but computer is still blocked, even time on computer is stopped. I tried this procedure few times, every time it is same. Also tried to disable lg virtual modem in device manager. Any idea what I could do ?
p.s. repairman in service told me that he tried it to flash it with riff box, process started but after few minutes if stopped and blocked his riff box
Related
i have lg gt540 and while updating to 2.1 with kdz tool the pc crashed now i cant turn on the phone...i hope some one help me with that
Have you tried updating again?
the problem the the phone dont open when i press power button there is nothing
what about when plugged into pc?
first thx for replying but there is nothing when i connect it to pc i think it needs abootloader.i hope u answer me
im afraid im pretty new to android ( gt540 is my first smartphone ) but anytime i updated, everything went ok, in fact yours is the first time i heard of a crash while updating so i cant give you much info but your in the right place, im sure the devs can figure something for you. just try remove the battery and then plug into your pc. and its not a problem replying just wish i could help.
well, did you try with the battery removed?
yes i did nd there is nothing
plz any one help in that
plz some one tell me how to make abootloader to it i have another lg gt540 i want to know if i can use it to repair the bootloader for this dead phone
The problem is theres noway u can acces inside the phone memory to patch bootloader. Go to lg waranty and tell them this happened when u were updating phone, dont tell them that pc crashed, tell them u updatet through lgsupport tool too, not through kdz updater they should fix it for u.
Sent from my GT540
thx for replying i will call them tomoorow i hope they will fix it for me... i want to ask if some one has passed with the same problem b4
Goto Emergency Mode, and upgrade from KDZ program. In KDZ program, you must setting Phone Mode to CS_Emergency. And flash agan.
i sent them email about the problem and this was the reply
Thank you for your email regarding this issue.
Unfortunately due to the nature of this issue, you will no longer be able to finish the update service. In this case you would be required to return to ourselves for servicing. To action this please contact the number below with your reciept and handset to hand.
If you have any further queries, please do not hesitate to contact us again.
Best regards,
LG Electronics UK Helpdesk
can any one tell me what should i do
Remove battery press volume - or + I can't remember try two options, then plug in usb.
You should see blue screen with DOWNLOAD or EMERGENCY MODE text.
i tried all keys combination nothing work
my mobile internet went dead after flashing quarx rom (I did it wrong btw...), but everything else worked fine.
I couldn't get mobile internet back on track no matter what (it was disabled in quick settings when I flashed quarx), I even tried factory reset and flashing the baltic rom. during the flashing, the kdz updater gave me an error close to the end, and my phone became stuck at the android screen.
even though I have CWR installed, so I could flash it again, I sent it to LG claiming I was updating through their website and since my phone doesn't start. I didn't tell them anything about the mobile internet not working. Hopefully they'll clean the phone completely and that will fix it.
I'll be picking up my phone after work today, I'll let you know how it went.
Same thing Happened to me n almost **** my pants for killing my brand new phone..
follow these steps
1. volume +or-(i dont remember) +camera n power on. it should turn on n say downloading mode.
2. update( you can use kdz updater, it probably wont crash this time but even if gets stuck just w8 for it)
3. after updating, remove the usb cable n turn on the phone, hopefully it would work
4. ENJOY ( N THINK TWICE BEFORE EFFING WITH THE PHONE, )
i am not sure about the keys for emergency/downloading mode(i think it was vol-) GOOGLE IT IF KEYS DONT WORK.
Put to microwave on 2 sec without battery and send do service
my service provider fixed my phone in 3 days without any issues, they flashed the t-mobile branded 2.1 on it. went home and now I have the open europe with fastboot and cwr.
so if all else fails, just send it to LG or your provider.
cheers!
hey frnd can any one plz help me....
i have ported GT540 2.3 SwiftDroid CM7 Project Mur4ik and clean 2.3.1 in my lg gt540.
how can i back in normal 2.1?
plz help me...
bcoz i want to sell my phone early....
thanks.....
Downgrade from 2.2.1 (2.3) to 2.1
1. We go in and write FastBoot:
- Fastboot.exe-w (This command does XP)
- Fastboot.exe erase system (cleaning section System)
- Fastboot.exe erase boot (clean partition boot)
- Fastboot.exe-w (To be sure)
2. Flash a rom with kdz updater
got it from 4pda, it should work.
It will not work: many have problems after first time use fastboot roms. It looks like that only small percent of owners can flash GT540 with stock ROM and in that case phone work. Many can flash but phone stuck at boot logo. If you use fastboot 2.1 it will work normally
^^
so i cant downgrade my phone with ROM that have no fastboot?
Try, you cannot loose anything. Maybee you will be in that few pwercent of users that downgrade works.
Just use a fastboot rom, I sold my silver GT540 with a fastboot rom on it then got a White one, to be honest, Most phones from other manufacturers have fastboot enabled anyway, so I don't see it as a problem
Jack
Well i'd recommend using your backup you made using clockwork recovery
I hope you made one
ohh u m not take backup of orignal 2.1..
have any one backup
plz give me link of bakup 2.1
Sent from my GT540 using XDA App
It does not cause a problem to downgrade to 2.1 without fastboot, I have done that several times. All you have to focus on is the following:
after doing "fastboot -w" turn the phone off. And DO NOT TURN IT ON AGAIN. Remove the battery, sim and SD. Hold the camera + power and then plug the phone to usb it will run into download mode. Run the KDZ updater with CS Emergency mode and flash whatever 20A rom you can have. Before the update ends, it will reboot and ask you to insert the battery. Do not unplug the phone until the KDZ updater gives you the ======= finished ====== message.
I hope this helps.
first, try restore with clockworkmod the backup of the 2.1 rom and after flash the original rom with kdz
guide here
i have followed all the steps but when i connect phone to the computer and try to run the kdz updater i get phone not found and ideas whats wrong
The king
You are the man, thank you sooooooo much, two weeks on getting the downgrade working and this works a treat.
After downgrade I was able to get into the unlock menu and was able to enter the unlock code, I am so happy for your post.
Ernie
Dr.Alani said:
It does not cause a problem to downgrade to 2.1 without fastboot, I have done that several times. All you have to focus on is the following:
after doing "fastboot -w" turn the phone off. And DO NOT TURN IT ON AGAIN. Remove the battery, sim and SD. Hold the camera + power and then plug the phone to usb it will run into download mode. Run the KDZ updater with CS Emergency mode and flash whatever 20A rom you can have. Before the update ends, it will reboot and ask you to insert the battery. Do not unplug the phone until the KDZ updater gives you the ======= finished ====== message.
I hope this helps.
Click to expand...
Click to collapse
to andynolan1
yeah just turn your phone off and plug in your usb, hold camera and power for a bit and it should connect. It may still be black screen but do not worry, then run kdz. I can tell when it connects by have my computer open on windows 7 and you will see it flash up on the left hand side. Other times I hold power and home key? The trouble I had was just horrible but just be patient.
Ernie
Hello, I ran into a problematic brick on my L5...nothing seems to work to unbrick it.
I followed the guides step by step using the KDZ updater and the appropriate firmware for my country, but it doesn't work.
How I bricked it:
I had CM10 installed and perfectly running for a month, so today I decided to attempt an overclock to speed the device up a bit.
So, I downloaded and installed the modded kernel, flashed it using CWM and rebooted the device. After that, the device just keep booting up, showing the LG logo and then a black screen.
Now, after trying to flash the old firmware after going into download mode it just stops on the LG logo with the flare (sun ray effect) spinning around the logo all the time...It's been like that for almost 30 minutes now. I attempted re-flashing it 3 times but nothing seems to work.
What do I do?
Thank you in advance.
It's bootloop. When I had L5 I had the same problem after flashing bricked phone via KDZ.
Do hard reset with key combination. It worked for me. Phone will boot up few minutes.
LeoFalto said:
Hello, I ran into a problematic brick on my L5...nothing seems to work to unbrick it.
I followed the guides step by step using the KDZ updater and the appropriate firmware for my country, but it doesn't work.
How I bricked it:
I had CM10 installed and perfectly running for a month, so today I decided to attempt an overclock to speed the device up a bit.
So, I downloaded and installed the modded kernel, flashed it using CWM and rebooted the device. After that, the device just keep booting up, showing the LG logo and then a black screen.
Now, after trying to flash the old firmware after going into download mode it just stops on the LG logo with the flare (sun ray effect) spinning around the logo all the time...It's been like that for almost 30 minutes now. I attempted re-flashing it 3 times but nothing seems to work.
What do I do?
Thank you in advance.
Click to expand...
Click to collapse
I was forced to do a hard reset...that sucks but it had to be done.
Thank you.
I have a worst brick, I was rebooting when my phone frozen at the shuting down page, so I took out the batterie, then when I tried to turn on .... nothing, not even lg logo, nor buttons lights, ... nothing, I can't even activate download mode to reflash it!!! what can I do???, does anyone had same problem before
please help me I'm really starting to freack
aeoros said:
I have a worst brick, I was rebooting when my phone frozen at the shuting down page, so I took out the batterie, then when I tried to turn on .... nothing, not even lg logo, nor buttons lights, ... nothing, I can't even activate download mode to reflash it!!! what can I do???, does anyone had same problem before
please help me I'm really starting to freack
Click to expand...
Click to collapse
i had the same problem with my l7 ... problem was solved in an authorized gsm service with jtag method...
but i will try to help u with this... Your phone is seen in device manager as unknown or lge android platform or adb ... ? if so, try with adb sdk tools...
nastase.alex said:
i had the same problem with my l7 ... problem was solved in an authorized gsm service with jtag method...
but i will try to help u with this... Your phone is seen in device manager as unknown or lge android platform or adb ... ? if so, try with adb sdk tools...
Click to expand...
Click to collapse
nop, it's like the device is dead,
Have you tried it:
Hold together volumn (-) + home button, then turn the power on
sorry for the delay, The phone was dead so I send it to the warranty and they send it to LG and then returned working so I just had to reroot it and update it again
so there is no solution to this brick???
aeoros said:
sorry for the delay, The phone was dead so I send it to the warranty and they send it to LG and then returned working so I just had to reroot it and update it again
Click to expand...
Click to collapse
Quote:
Originally Posted by breakercris
I've tried everything.
The phone simply doesn't connect.
USB\VID_05C6&PID_9008&REV_0000
This is what I get when I connect the phone by USB.
I just cant get into emergency, DIAG or emergency CS
KDZ the phone connects and then I get a message afterwards PHONE NOT FOUND.
everytime I install the drivers by LG support tool, it keeps giving me the option to install the driver, like I havent done it a hundred times over.
I think there should be a driver somewhere that can be installed but the only people that have this driver are LG tech's. So they can bill you after
send the phone in cause you rooted it. So the one billion dollar question is witch hero will find a way to unbrick this device. We only need a way
to get a driver to install and we are home free. Or maybe the only other option is throwing the phone for sale on internet for spare parts
HELP PLEASE HELP find a way to unbrick this phone. Believe me I flashed and bricked alot of different phones and there was a way out but in
with this phone it seems impossible!!
And there is no mode to put it in in because te volume buttons don't do crap, the home button also, the only time that the phone does show up is when windows tells me it has an unknown device that I for the love of god can't find a driver for. I tried SDK, the LG drivers, but no dice
Did you try emergency mode? (volume up + volume down + power button)
If not, see if you can enter it and then flashing your stock firmware with Software update [KDZ] 1.0.4.4 (KDZ-Flasher).
Hey guys , my not so smart friend tryed to be smart and tryed to flash custom rom WITHOUT rooting, and WITHOUT any recovery :highfive:. Long story short the phone is bricked completely. Mainly it stuck in LG logo for a long time and sometimes it actually load the system but crashes after a few secs, again, to LG logo.
Is there any way to root the phone without going into the system( usb debugging etc)?
p.s.
tryed to do factory reset and the result as above.
Thank you in advance guys!
After 7 hours I found a solution to this insane situation. I never had to recover such a dead phone. No root, no recovery , no backup, no rom on the device. Any way Im proud of myself
If someone has the same problem I might be able to help!
Seven Winds said:
Hey guys , my not so smart friend tryed to be smart and tryed to flash custom rom WITHOUT rooting, and WITHOUT any recovery :highfive:. Long story short the phone is bricked completely. Mainly it stuck in LG logo for a long time and sometimes it actually load the system but crashes after a few secs, again, to LG logo.
Is there any way to root the phone without going into the system( usb debugging etc)?
p.s.
tryed to do factory reset and the result as above.
Thank you in advance guys!
Click to expand...
Click to collapse
....how did he flash it without recovery? what a dummy...Its bricked... he deserve a $500 brick
U can try to use LG flash tool to fix but I doubt its gonna work, but hey suprise me.
G1_enthusiast said:
....how did he flash it without recovery? what a dummy...Its bricked... he deserve a $500 brick
U can try to use LG flash tool to fix but I doubt its gonna work, but hey suprise me.
Click to expand...
Click to collapse
Yeah, I told him to wait for my help (not that im a pro,but i had some experience rooting and installing roms on htc sensation and now on my galaxy 4)..
Any way, as we speak I am downloading stock rom and will try to use the flash tool but Im really doubtfull It will work as well.
Thank you for the answer!
Seven Winds said:
Yeah, I told him to wait for my help (not that im a pro,but i had some experience rooting and installing roms on htc sensation and now on my galaxy 4)..
Any way, as we speak I am downloading stock rom and will try to use the flash tool but Im really doubtfull It will work as well.
Thank you for the answer!
Click to expand...
Click to collapse
does the computer recognize the phone at all?
G1_enthusiast said:
does the computer recognize the phone at all?
Click to expand...
Click to collapse
After installing the driver, when the phone is powered off, no. When the phone turn on, no. When the operating system turns on, I dont know, not enough time (phone restarts after a few secs).
I do hear the indication sound from windows that something is connected but nothing turns up..
Seven Winds said:
After installing the driver, when the phone is powered off, no. When the phone turn on, no. When the operating system turns on, I dont know, not enough time (phone restarts after a few secs).
I do hear the indication sound from windows that something is connected but nothing turns up..
Click to expand...
Click to collapse
lol I think its good as bricked.
G1_enthusiast said:
lol I think its good as bricked.
Click to expand...
Click to collapse
I did it! wow, took 7 hours ! :victory:
Just so you know how :
1. Need to be in fastboot mode
2.Do like in this thread with the CMDhttp://forum.xda-developers.com/showthread.php?t=2477595
3. Then basicly follow the steps here http://choimobile.vn/threads/huong-dan-cuu-soft-brick-lg-g2-f320s-l-k.12932.html
4. Whats important though I think is turn off your computers internet connection, dont know why, but it will fail otherwise.
Step By step
After you collect those DLL & TOT files, here's step by step :
1. Disconnect any internet connection
2. Set the computer time before Juli 15th, 2012 ( I set March 1st, 2012)
3. Double click LG Flashtool. Username, password, and Registration key are on the link #1 post http://forum.xda-developers.com/showthread.php?t=2396048
4. Insert DLL file in DLL column. Browse to where you put the DLL file.
5. Insert TOT file in Software column. Browse to where you put the TOT file.
6. Click OK
7. Click the GEAR icon, set only port #1 that ticked. Other ports are UNTICKED. Click OK.
8. Press & hold volume UP , while connecting the USB cable to your computer (set to DOWNLOAD MODE). Until the phone shows "DOWNLOAD MODE" on the center of the screen.
9. Open System Properties. Device manager ->Set COM port for LG Handset using port 41.
10. Click Arrow Right in LG Flashtool, disconnect USB cable for 5 seconds. Reconnect USB cable.
11. The FLASH process in progress, wait for 600 seconds and shows green background say "PASS".(In my case at around 86% The phone already worked, the flashtool still did his thing and failed at 90 something percent.Doesnt metter because phone works)
12. Disconnect USB cable and close the LG Flashtool application.
wow props to ya...how did u get the IMEI back?
Why kids messin with phones when they dont know what they doin .. aaahhh
my phone LG G2 D802 International Version was running perfectly fine i tried to flash another rom by LG FlashTOOL and in the first i got soft bricked on that fastboot screen i recoverd it by ADB (fastboot.exe)
fastboot erase recovery
fastboot erase laf
fastboot flash laf laf.img
and then i tried to reflash it then i got this mesg on screen
---------------------------------------------------------------------------
Critical Error!
---------------------------------------------------------------------------
DemiGod Crash Handler : Critical Error!
Press Key to Choose Dload Mode or Reboot
1) Volume up : Dload Mode.
2) Volume Down: Reboot.
If u choose Dload Mode.
please do following action.
1) Dload Mode. please Connect USB
2) Get the Ram Dump image using QPST Configuration.
-------------------------------------------------------------------------
Board Info
Rev. : 1.1 speed.pvs : 1.1 Serial : 01e862cf934fc622
Please Help me somebody ... i cant afford to buy new phone i just bought this phone a week ago ..
Having same issue ! XDA forum experts always helped me with every situation with my phones. Expecting help this time as well from you experts.
Same here, enyone can help, i stuck with the sam message, presing vol- just rebots, and vol+ sends message "jump to download mode" but i cant flash stock firmware
i have the same problem any help ??
I have the same issue too, can anyone help?
I heard that this can help you guys. Use the search option there and try to fix it. Actually i had the same problem few months ago, but for me mew motherboard was the solution... If you're device is under warranty send it saying it failed while taking OTA. Good luck...
lg g2 critical error
I have done a flash to my g2 32gb d802 and it suddenly entered into critical error not going into any of thefastboot mode or download mode even though it is giving me options.....please any one help me out to get my phone back to normal ........
PM me if you guys need help.
I had the exactly same problem, and I had to go to afterservice center to repair. Engineer told he would wipe everything and install new rom. but He failed to write rom so he simply changed mainboard.
At first I had thought about open my g2 and makes it go into qualcomm download mode by short-circuit.
the reason I didn't was my warranty was still available.
I tried every method to make it boot into recovery or download mode but I failed. In my opinion, you may try short-circuit method for last solution. In this situation, even linux doesn't mount rom's storage section. Only if you can make G2 recognized in Linux, G2 will revive.
good luck.
xmayhemreturnsx said:
PM me if you guys need help.
Click to expand...
Click to collapse
i still don't know what to do HELP
yassou92 said:
i still don't know what to do HELP
Click to expand...
Click to collapse
The best way to go if you do not have a warranty is to short circuit the board and get into Qualcomm ... 9006 mode. However, when you get the demigod error plug in you usb and click up and it should start download mode even though it doesn't show it.
xmayhemreturnsx said:
The best way to go if you do not have a warranty is to short circuit the board and get into Qualcomm ... 9006 mode. .
Click to expand...
Click to collapse
How do you short the pins? There's a guide here on xda but it's so difficult to undestand. I need to know how can I short the pins.
it should start download mode even though it doesn't show it.
Click to expand...
Click to collapse
No, it doesn't. I try to use flashtool but it doesn't recognize the phone. No download mode in any method I tried
I got into this error after I had previously recovered into qhs_usb9006_bulk mode from a hard bricked D801, by shorting the capacitors on the main board. After entering qhs_usb9006, I used srk tools 2.1 for my phone, and after they finished, I tried entering download mode, only to get into this error. I really don't know what it is to say about this. Everything turned wrong with this phone, it went from simply failing a .kdz, to stock .tot, to hard brick, and now to this error, whereas it should've just enter the download mode, as for the 99,99% of the others. Any help would be really appreciated. Thanks.
L.E. I shorted the capacitors again (the one i the middle, like I did the first time, when i got into 9006 mode. 5000 and 5004 didn't work for some reason). This time I got into dload mode, which is 9008. I'll try to recover the phone from here, with this method:
http://forum.xda-developers.com/lg-g2/general/fix-unbrick-lg-g2-stuck-qualcomm-hs-usb-t2933830
i had this problem while trying to return to stock. Fixed it by following this guide http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404 . it needs some hardware tampering though. i tried and tried but i cant flash the phone any other way. the way i understand this is due to bootloader being corrupt.
I installed autorec from playstore solved all the problems
Than you! autorec worked for me too
Can someone post a KK baseband for D801 (T-Mobile)? I'm on D80120a software version with unknown IMEI and baseband (the phone is a D801 refurbished into D802, I more than hardbricked it by flashing wrong .kdz, got it recovered through shorting pins, 9008 mode, got download mode, D80120a stock, root, twrp, after a very long and painful process of about 1 month). Now I have to make use of QPST, but I have to obtain a valid baseband first. Of all links I've stumbled upon, only 5% or less of them are still working, so I only have one flashable modem, in twrp recovery, which corresponds to D801 jb version.
http://downloads.codefi.re/autoprime/LG/LG_G2/G2_modems
cloudyfa kk_baseband_D801 only make my phone restarts like crazy.
I'm simply stuck and pray for some devine help.
Thank you.
Weird enough, I flashed a canadian modem and I got both baseband and IMEI. Why did I do that in the first place? Because I remembered that before all these things happened to my phone, the baseband was M8974A-AAAANAZM-1.0.190082, which corresponds to D803. So I said to myself what can happen by flashing the wrong modem? Boot loop, easily fixable with the phone in it's current state. But again, after 1 month of trouble with the phone, I'm back to what exactly started it in the first place: phone seem to work OK but it has 2 huge problems: WiFi extremely weak (2 meters away and a wall or 5 meters away and no wall a and I lose the signal in both cases; the 2nd is wit the GPS - 20-30 meters error). No idea how should I adapt the radio to Europe region (by keeping the canadian one and change the settings, if it's even possible/fixable this way or if this even does make any sense).
I had to do a hard brick fix to get it into the QSUSB mode to flash TOT.
Have you tried using LG Support tool to put it back to stock?
Sent from my LG-F350K using XDA Free mobile app