Related
I got a serious problem with my mda vario here.
sometimes, 7 out of 10 times, when i get a call the screen gets totally corrupted and jumbled like on the picture in the attachment. i can only see black vertical lines on a white screen. in order to make the screen work properly i have to turn the phone off/on (stand-by mode) then.
does anybody know where the problem is?
i have to confess, that the phone slipped out of my hands and fell on the ground 3 times so far.
thanks
well, you say youve dropped it 3 times already? is it possible that something may be loose inside? is there cosmetic damages from dropping?
yes, there are some scratches on it. i don't really think that something is loose or broken, because the screen gets only on icoming calls corrupted.
so i don't think that it is due to a loose contact or something like that...
I have exactly the same problem. I personally think it is unlikely that dropping the phone has caused it as it corrects when you cycle the power button. Any help on this from other forum member would be much appreciated.
roads said:
I have exactly the same problem. I personally think it is unlikely that dropping the phone has caused it as it corrects when you cycle the power button. Any help on this from other forum member would be much appreciated.
Click to expand...
Click to collapse
Any resoluation this? I have the exact same problem!!
Oh dear ... somethings in the air...
mine's got it also. first time i saw it was a couple of days ago. only happens with the alarm clock in the morning :?
My phone is crap like hell... gotta hard reset and reconfig the damn thing. acting up lately...
(ps... AFAIK i barely dropped the phone... maybe 1 or 2 times. nothing more)
I have the same problem
I have read the service manual of wizard and said:
Unusual Vertical / Horizontal lines or partial display
(1) Check the connection of LCM FPC whether is properly connected. (Is a conector between motherboard and LCD)
(2) Try with another LCM. (LCM=LCD Screen)
(3) Try with another Main Board.
(4) Replace LCM if necessary
(5) Replace Main Board if necessary.
(6) Once the defective part has been identified, verify it again with the defective part whether the
symptom could be duplicated
Any sugestion?
Okay..
so far, i have installed Molski 2.26 rom (30meg free version) and upgrade the radio rom form 2.25 to 2.47.
I have not had another occurance of this so far.
Maybe a fluke.
Screen fixes when pressure applied to bottom of the screen
Guys,
I now have to keep my finger pressed hard against the bottom of the lcd unit to get the screen to display to work properly. it is under warranty with Imate but they want me to send it to Abu Dhabi for repair. I'm in Canada and concerned that I may not get it back.
So has anybody else identified this as being a loose connection rather that a real hard fault. Also has anybody fixed their unit by dismantling and reseating the connections.
Finally has anybody used the Imate repair service and was it timely & reliable?
Any advice would be appreciated.
Mick
This is a real hard fault.. had it with my mini s, took it into the shop, it was away 2 weeks... and in the end they gave me a replacement!!
I agree - took it completely apart and cleaned everything ....
And still have the issue.
Serves me right for buying something in Middlesbrough I suppose
It must be a hard fault with the LCD assembly. Will have to see how Dixons handles an overseas repair.
Take care & thx,
Mick
I had the same problem, in the end i took it into my local t-mob shop to have it repaired, they ended up sending me a new one.
Well, I've exactly the same problem since the past two-three weeks, it also occurs only in the morning. I'm living in the Netherlands and this is happening since it's rather cold over here, especially in the morning (3-4 degree Celcius). Since my bedroom window is open during the night, it gets rather cold in my room.
During the rest of the day it is +8 degree Celcius, and the phone works flawless. Maybe this problem has something to do with the Temperature?
Temperature
Bebob - don't thin so as I have had this problem for a number of months and the temp here in the summer is high (30+ degrees C)
It looks to be a bad connection type issue and may be a bad screen cable. It makes sense though that the issue is at the bottom of the screen cos this is where we press the select buttons all of the time.
Pls keep me posted on how you do. mine is going to a local repair shop (on my dime) tomorrow to see if they can fix it.
If not can any of you guys recomend a new unit that could be considered an upgrade to the KJAM ?
Many thanks
Mick
suggestions needed
friends, i have o2 mini s and got the same problem with screen for the last 3 weeks....
can anyone tell me that will the problem aggravate or else will i be able to use my cell properly for few months...
and also what will be the approx cost of repair..
all suggestions will be warmly appreciated...
It's happened to me as well. I have lived with that for one month now. It is happening, when I touch the cursor keys or when touch the lower part of the display. I tried "shaking/hitting" the xda and it looks better, so I assume it is a faulty connection cable.
I have active Cleartype and no more vertical lines for the past 2 days.
I seems to be a problem when background is white and leters are black.
Regards
similar problem
i dropped the phone (T-Mobile MDA Vario) and now when i turn it on the screen is fine for 5-30 seconds but then it scrambles, but works again if i smack the bottom of the phone on my hand!
t-mobile staff told me there are sensors to identify if it has been dropped. I'm suspicious that it could even be programmed to go "faulty" once it is dropped as the screen is fine for a limited time so it obviously works somewhat. do you know if this is the case? or what's happened? also is it a simple thing i could do myself? i didn't take out insurance so that's why i haven't just claimed off that as i'm really broke
Any help is appreciated
Regards,
Steve
whiteish screen / over temperature
hi,
I have a problem smilar at qtek 9100. I had upgade to my ppc wm5 to wm6 around 3 week ago and overclocked to 221 mhz with batery status today plug-in . 2 days ago Screen became whiteish (almost no contrast or over gamma) and working temperature is around 30c. I tried to re-flash with many kind roms but noting chaged.
Is there anybody has these kind of experice. If I can not solve. I am planing to buy new LCD ( I am not sure new LCD will solve the problem)
Thanks
Same problem here. Dropped it ONE time and the screen went crazy. Sent it to my t-mob shop and they got it repaired. They said in the report that they changed the "flex". Dunno if this helps.
Hi, I come on here quite a lot for information as it's an amazing resource! This time however, I'm attempting to give something back!
I experienced the "black screen on slide out" on Monday. Phone completely screwed. I've also had a few droppages and had it apart once before so there's no way warranty is gonna help!
I stripped it down and soon discovered what it is that actually fails on the ribbon. The coating had worn through due to rubbing on something during the slide out / in process. it had been playing up for a while, probably due to shorting out on the metal case, but now the tracks (aluminium?) had worn right down.....
In pic 1 i've circled the worn area. The shiny section is where i'd tried taping over it to prevent shorting, before i realised the tracks were gone.
Got an almost new one off ebay for 15 quid and, realising it was going to happen again, came up with a solution that, so far, looks like it will work....
A while back I bought some "anti rattle felt" for my car's dashboard - really thin and strong self adhesive felt to prevent squeaking joins between dash sections. I cut a piece of this and stuck it to the new ribbon. Once this stuff is on it's well stuck, by the way!
See pic 2 for the modded ribbon cable.
On reassembly everything is working just fine so far! Here's hoping that it lasts longer than 6 months this time!
Just need a new casing now as mine is decidedly second hand!
Hope this turns out to be of use to someone!
cool story bro
when i took apart my xperia to replace the housing this seemed like a really weak point in the device. glad to see someone who has had the problem has been able to fix it
Why does the screen go black?
Hi,
When the coating wears off the ribbon cable it exposes the tracks in it. when you slide the keyboard out the exposed tracks short out on the metal casing and the screen loses it's input signal.
thats whats happened on mine at least and i presume quite a few others?
HTH!
Update:
That's interesting: My phone was also losing signal with the keyboard out, and occasionally while closed up as well. It would just randomly drop to "no signal" for a few seconds.
It hasn't done it since replacing the ribbon cable.....could be coincidental of course.
I'm having the same problem
It just started a week ago and I got the phone in January off of ebay. I'm new to opening up the phone so could anyone help me find the correct tools or have a link to a site with pictured instructions?
I noticed that the sliding mechanism started to go loose about 4-5 months ago but didn't expect the screen not respond in landscape mode. I have yet to see the other symptoms you all are referring to. I would like to fix this before it get worse.
In mine case it went totaly black after one week of this problem... You have all the instruction on youtube, there is where i looked. For tools you can be inovative, but the exactly right ones come with housings from ebay, it is only 15EUR, and i bet you have some cracks so it wouldn't hurt replacing. That is what i did, along with ordering new sliding mechanizm, and new ribbon cable.
I am open for ideas to prevent my ribbon cable from being cut at it weakest point again.
I'm assuming my flex ribbon went bad yesterday, since sliding the keypad out causes my screen to shut off.
Already ordered a cable off ebay and will attempt to replace it myself :O
Replaced my flex ribbon cable with one I bought on eBay. The screen doesn't turn on at all now, which leads me to believe the cable I was sent is defective. Put the old one back in and it works okay, less landscape mode. ughhh what a pain.
great tips! my input is I bought a case off of ebay that was ~60$ and everything actually fit fine for me...so I wouldn't discount every seller but you do get what you pay for, the 15$ cases are probablly the ones that will give you problems
I working in a mobilephone repair center if anyone need help drop me a priv... i able to get 2nd hand or even brand new components
Replaced the flex ribbon cable -
I got my flex ribbon cable a few weeks ago and took it to my local repair shop. They replaced it but the LCD screen/optical joystick receives no power. The touchscreen and everything else on the phone works just fine now. I thought it was a defective item so it was exchanged with a new one.
Got the repair shop to replace it again and the outcome still remains the same as the first.
Theres no light coming from the screen nor the side illumination.
I just told the repair shop to just place the original back in for the mean time.
Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power botton.
Could it be defective a batch that the seller was sending out? or the repair shop's mistake and is playing dumb so they do not have to admint fault?
Hopefully there's an easy fix to this problem.
-Also I did inspect the ribbon before and after the repair. looks new as the OEm
Can anybody help me out with this new problem after replacing the cable -
perhaps you should try a hard reset. Ive had problems in the past where the optical joystick and the illuminators did not work, and that worked for me.
On the other hand, the top illuminators are on the same piece of hardware as the flex cable that was replaced, so a faulty flex cable is possible. The bottom illuminators are on the circuit board that the optical joystick attaches to, separate but connected to the flex cable.
Ive recently replaced my flex cable and touchscreen. The experience i had with the faulty touch screen was that it appeared to receive no power, but was in fact displaying a dark backlit illumination that could only be seen in the dark. At the same time however, the screen did not display anything. I'm not sure if this is similar to your experience, but if so then your touchscreen would need to be replaced.
ive done all repairs on the xperia myself, and one thing ive discovered is if something doesnt work right after a repair, simply disassembling it and reassembling it to make sure all the connections are properly done has worked for me in the past.
"Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power button."
Now when you say the power button, do you mean that a red light appears under it?
I dont know if i can come to a conclusion or that i can help (or have helped) you come to a conclusion, but i can only assure you that the xperia acts out in strange and weird ways.
Good Luck!
Tags
Dismantle / Disassemble Sony Ericson Xperia X1
http://www.ifixit.com/Teardown/Sony-Ericsson-XPERIA-X1/788/1
http://www.formymobile.co.uk/xperiadisassembly.php
http://www.youtube.com/watch?v=AWDurQrRt-Y (REAR)
http://www.youtube.com/watch?v=iyGUbxFqvyc&feature=related (FRONT)
http://www.youtube.com/watch?v=elgC8hwHfYQ&feature=related
For info.
Mike
Thanks for the links. I've tried the hardreset and restoring the original rom but the issue is still there. It's really bugging me that everything works but the LCD screen. I'm currently using MyMobiler to use my phone. The touch screen works fine and so does the soft keys. Just no power for the lights. I might just give up and wait for another phone that catches my eye and then tinker with the xperia myself. but if anyone got a solution or want me to test something then I'll give it a try.
My warranty is no longer affective so I'll use my phone as a tester to help others with any problems.
TRIONDAVE, how's your Xperia running now with the cable mod that you did? Its been 6 months since you created the thread. I hope you're still around.
My Xperia X1 works nearly fine, except for the keyboard issues, so I'm thinking of opening it up. If your Ribbon mod helped I might just do it too once I've got it opened. Mine has a MOUNTain of cracks though, and the battery compartment itself is cracked on both side enough to make the compartment CURVED. Hence the Battery cover doesn't sit well.
I'm looking around for broken Xperias which I might be able to use to change the internal cracked casing. Lets see.
DatDereX1 said:
cool story bro
Click to expand...
Click to collapse
My thoughts exactly.
Hello guys, I am in need of real help over here!
Its just that Ive replaced my ribbon cable, the old one got screwd up.
However I got done for 10 minutes ago, tried to start up the phone.. without success :,(
The ribbon cable doesnt have anything to do with the start up, only the screen am I correct? Cause I cannot even start my phone..
Ive connected the charger, but when I remove the battery it shows a red light, meaning no battery, correct?
So what may the problem be exactly? Maybe the battery is all dead, or?
PLEASE HELP!
for the people with ribbon failures how long have you had the phone before it occurred ? im just interested on the cables lifespan.
mine is fine so far but i have noticed the slider is flimsy and rocks left and right.
hay from today morning my htc touch shows a white screen and a crack on the bottom corner of the screen.i am sure that it dint fell down.
then what may be the problem?
anyone knows pls tell me...
white screen?
When you turn on your phone, there is no smart mobility.
Crack?
Is that an LCD problem?
i have the same problem with the WHITE SCREEN. bought my ELF 3450 second hand over the net. i am from the Philippines by the way and HTC units are not yet very common here and also the parts/accessories. it worked fine for about 3 months with minor problems such as Auto-Restart/Auto Power On/OFf which was solved using the "plastic on the OMAP chip method" - tnx for the forum for the info by the way and charging problems which was also solved by buying me a aftermarket charger. but recently the problem of AUTO OFF occurred again until it did not work at all. so, i tried to check the Plastic over my chip but to no avail the fone was dead. so, i decided to head to one of our local cellphone repair shops and have my OMAP heated thinking that maybe there are just contact points inside who became loose. when we tried to power on it was good for a few minutes then i noticed the screen went darker and darker and then it was all WHITE. we restarted it but it's just WHITE. tried to send messages and call it but there is no response from the fone. i'm afraid i toast it bad or may be it's just the LCD who got toasted, i am clueless.
CAN SOMEBODY PLEASE HELP ME WITHMY PROBLEM. CAN I GIVE LIFE BACK TO MY ELF? WHAT'S THE CHEAPEST & BEST SOLUTION TO THIS? THANX ...
Generally white screen problem are caused by defects in flex connecting the LCD to the mainboard or the connector itself. Try to disconnect and reconnect the LCD, if doesn't work - replace the LCD.
kimberhunt said:
i have the same problem with the WHITE SCREEN. bought my ELF 3450 second hand over the net. i am from the Philippines by the way and HTC units are not yet very common here and also the parts/accessories. it worked fine for about 3 months with minor problems such as Auto-Restart/Auto Power On/OFf which was solved using the "plastic on the OMAP chip method" - tnx for the forum for the info by the way and charging problems which was also solved by buying me a aftermarket charger. but recently the problem of AUTO OFF occurred again until it did not work at all. so, i tried to check the Plastic over my chip but to no avail the fone was dead. so, i decided to head to one of our local cellphone repair shops and have my OMAP heated thinking that maybe there are just contact points inside who became loose. when we tried to power on it was good for a few minutes then i noticed the screen went darker and darker and then it was all WHITE. we restarted it but it's just WHITE. tried to send messages and call it but there is no response from the fone. i'm afraid i toast it bad or may be it's just the LCD who got toasted, i am clueless.
CAN SOMEBODY PLEASE HELP ME WITHMY PROBLEM. CAN I GIVE LIFE BACK TO MY ELF? WHAT'S THE CHEAPEST & BEST SOLUTION TO THIS? THANX ...
Click to expand...
Click to collapse
You warmed the OMAP? Interesting....
This problem sounds really complicated.
And im quite surprised of your 'warming' method.
I've had the exact same problem combined with the fact that my touch was resetting constantly. I was about a minute away from throwing it out of the window when I tried the plastic-piece-on-omap processor-technique described in one of the threads here. It solved the rebooting problem, but not the white screen issue. After a very frustrating couple of days where the screen started to blink and shake and then eventually turned to white alltogether, I lowered my brightness to the second stop from start, and since then I haven't experienced the white screen anymore. I believe it is heatrelated.
Whilst not being a full solution to the problem, at least it renders the phone usable.
Hope this helps anyone.
Heating the device very seldomly solves anything, but causes more problems that you originally started with.
iam using htc touch (p 3450) for nearly 18 months . (bought & using it in india ) my hand set fell two times in water and about 15 times fell on the floor (from shirt pocket) . still its working fine .
and iam using "opera mini " for browsing the internet . for some sites iam using "opera mobile " . when iam on opera mini , continueously for long ours , suddenly it turns white . never come to normal screen unless restarted . but it happens sometimes , may be because of memory or heating up of some H/W .
Hi hotchamo,
my htc touch elf hat a similary issue, and my father just "wringed" it gently until the white screen disappeared. You should try it carefully, since it may help and it won't harm. Just take in in both hands and turn them in the opposite direction, so that the case gets slightly twisted.
If that doesn't help you should open it and check the LCD flat cable connector...
Best regards,
scheutak
Again - flex connector problem. 'Wringing' it gently will eventually result in your LCD cracking, by all means - go for it, it will solve your white screen problem. Permanently.
My nexus 7 currently has an unresponsive touchscreen. Almost none of my touches are working now and yesterday the tablet was working just fine but some of the touches were not working. Now almost all the touches arent working, did the hardware just fail on me?
lovenokia said:
My nexus 7 currently has an unresponsive touchscreen. Almost none of my touches are working now and yesterday the tablet was working just fine but some of the touches were not working. Now almost all the touches arent working, did the hardware just fail on me?
Click to expand...
Click to collapse
Here is what I posted yesterday on another thread, but short answer is that yes it's most probably hardware fault (I don't have picture at work, so can't attach it here).
I purchased my Nexus 7 from Staples during business trip to San Francisco. My device started having touch screen issues after few hours. Factory reset did fix it and I liked the device a lot so I didn't return it as I thought touch screen issue was just a SW glitch. Issue came back at the airport . Unfortunately I didn't have time to return the device at that point. Issue wasn't manifesting itself all the time, but seemed to come up every time I plugged the device in charger. Symptoms were exactly as in this video: http://www.youtube.com/watch?v=uVkvCXDKU2M and the other one in which multitouch is demonstrated. I suspected different applications as a reason to the problem as well as faulty charger. Then I found this thread and became assured that this must be a HW problem.
As I'm living in Finland and don't know when my next business trip to USA will take place I decided to try and fix the problem myself. I took off the back cover and touch screen worked perfectly. Initially I suspected grounding problem but pretty soon came to conclusion that it can not be the case. The problem in my case was the "sponge" pushing (what I assume is) display / touch flex. I have marked that in the attached picture. Even a very light touch to sponge caused touch screen to go crazy. As I don't have the luxury of immediate warranty repair I decided to remove the sponge and my Nexus 7 has been working flawlessly ever since. I can even charge and everything works as expected. When I started charging the device I placed my Nexus 7 on the table. It probably caused slightly increased pressure on back cover and therefore to "sponge". After removing the sponge I can't see any of the touch screen problems I was having. Couldn't be happier as I don't have any of the other problems people have found and device is working as it should, at least for now.
I don't encourage anyone to do what I did, but if you are in the same situation as I was with imported device, you can try to take off back cover and see if the problems are fixed. You should be very careful though not to break the device especially when it's powered on with back cover off. Hope this helps someone.
EDIT: 22.8.2012. Forgot to mention, that turn of WiFi if using device with back cover off. Turning off NFC and GPS won't hurt, although GPS is receiving only. Reason is that antennas are located on back cover.
Ok so basically I love the g2, but here is my problem, bare with me on this haha, BTW its completely stock n everything as its my 1st Android phone so didn't want to mess with it. So basically I broke my phone screen in January, bought new screen, followed a YouTube tutorial, replaced LCD+touchscreen, no issues super happy, had the odd issue where if I woke screen, would only be on for a second n then go back to sleep, but then upgraded to KitKat through computer software update, still nothing wrong, upgrade fixed the issue with the knock to wake, and then my worst day, smashed the screen again! On good Friday, ok I thought I'll just replace screen again, so I did, but when I put new screen on and tested it, all was well, until I made a phone call, the instant moment I press green call button, screen goes blank and won't come on no matter what, power button don't bring it back on or end the call, but I can hear the other person and they can hear me, had to turn phone completely n back on to be able to use it again, so I though hmmm dodgey screen, but just to be sure it wasn't the phone I put damaged screen back on, and the issue didn't appear, stayed lit up while in my hand, went off next to my ear, back on whole in hand, so I took it to local phone repair shop because I couldn't be bothered going through the hasstle getting refunds etc, they replaced screen, I went and tested it before paying them, guess what, same problem, so what exactly is going on? Has KitKat made the phone not work with a new screen other than the one I upgraded it with? I'm seriously confused and need some bodies help urgently my model is an unlocked lg g2 d802 16gb now I turned it on last week before I took it to be repaired, and it says I have software updates but I didn't bother installing them, is there a chance these could be related to my issue and possibly fix them? Its driving me nuts tbh
Chris
Hey Chris. It seems like your proximity sensor is messed up. I think the new screen you got yourself is worse quality or your damaged the proximity sensor when installing the screen.
Edit:
Please go into your phone app (where you call people) and type the following
3845#*802#
Then go into: HW Device Test and then ALC proximity test. Try testing your proximity sensor with your hand. It should change from far to near when your hand is about 2 inches from your phone. The proximity sensor is located next to the camera.
Sent from my LG-D802 using XDA Premium 4 mobile app
Ok thank you I will try that, I also thought a damaged sensor but when I put damaged screen back on after having the issue with my new screen it worked just fine, no blank screen when making a call, I retested it before I left it at phone repair shop, still was fine, then picked it up with a new screen and issue came back, I don't get why its been like this, I'm thinking bad quality screen and maybe try scratching the sensor area of the new screen to allow more light in? It may be to dark for it, what exactly do I do if it works fine when using that code, try another screen?
Chris
I doubt it will work when you use that method. It's just to make sure that it's the proximity sensor that's the problem and not some loose connection. And yes, a new screen would be your best bet.
Sent from my LG-D802 using XDA Premium 4 mobile app
Ok I won't try that method then lol, what if it doesn't work when I use that code, as I said I didn't have the issue with the damaged screen which I tested after having the issue with the replacement screen I'd purchased, so how do I know its not just the screen not allowing the sensor to see? Is there anyway I can reset the sensor to relearn maybe?
Chris
If you follow my steps, nothing bad will happen. It's just a way of troubleshooting the proximity sensor. I still think you should do it.
Sent from my LG-D802 using XDA Premium 4 mobile app
Ok I've spoken to phone repair shop and they agree it worth a try to see if its the screen or not, I'll let you know on Saturday after I've been and tested it
Chris
I just had this exact same issue.Turns out the inside of the screen was just dirty. I opened it up and took a q-tip to the inside of the screen and it worked perfectly after that. Also check the readings of the light sensor, as it is right next to the proximity sensor, if the screen is the problem it will likely have low readings as well.
Great I'm glad somebody else has encountered this issue, its been driving me nuts lol ok so I dial in the code that's been mentioned and what are the labels in the menu for the proximity and light sensors? I'm thinking its just a crap screen as the broken 1 worked fine after I put it back on after testing new screen, and I reckon the screen the repair shop has used is also ****e quality, but I just want to cancel it all out as I don't have the phone to hand to inspect as they still have it lol is there a picture somebody can post up to show what to not cover when replacing the screen and applying adhesive tape etc? Just so I can show them to make sure they have done it all properly.
Chris
Ok so just to update the problem, I went to the phone shop today, did the test, it was showing near all the time, but the light sensor reading was quite high, 166 or something, but I then tried squeezing the screen, index finger on back and thumb on front, gently squeezed it, and proximity sensor started showing far, and near as I moved my hand over it, but after few seconds, went back to showing near constantly, so I think its the screen not been seated, told the shop to take screen off, give it a good clean and reseat it. This sound good to you guys?
Chris
Anyone?
Bump! I'm only wanting a little extra advice so I don't end up paying more money out for another screen when it could possibly be proximity sensor? I think it was just the screen not seated properly, anybody have an idea or something else to either assure my choice or point me in another direction?
Chris