What Will I Need To Replace? - EVO 4G General

Evo 4 G took a couple hard knocks! Wouldn't you know it? I didn't have my Otter Box on it for just 1 day! Anyhow, my text is all messed up. if I hold the phone on the side the delete key just draws smiley faces. Tried Hard Reset and Many Roms but text is always messed up. to get a "s" I have to turn my phone. Then for a q I have to turn it back up. Big pain in the ass!.
What should I start replacing? Is it the screen or something else? Thank you for your views and any help!

Sounds like the digitizer is borked. Either that or something came loose inside the phone. Have you opened it to look for loose/broken components? Check to see if one of the cables came loose?

No, I haven't opened it yet. Thinking the digitizer too. Last time I tried one of those it was on an htc tilt. Didn't go well. Are these better or should I get the whole screen?

I would replace the whole screen. When I took the digitizer off I had issues not placing dents on the plastic housing around the glass.

Just replaced the glass/digitizer and it's good to go! I heated the old glass up and used a knife to start it up @ the top, careful to only pry the glass. Once I got the top loose I was able to place my I.D. under the glass and remove with ease. It is a pain in the ass getting it started, but once it's heated and your under, it come off easy.

Related

Broken Screen on my XV6800

I dropped my XV6800 on a curb yesterday. The picture on the screen is fine, but it looks like the touch screen cracked and now no longer works. The phone won't even let me unlock...don't ask why I locked it after that happened Anyway, I can't do anything with it at all now except receive calls.
What is the cheapest and/or easiest way to fix this? Good source for parts etc..
Thanks!
use mymobiler on computer to unlock and such. But a new touch screen off ebay and put it in.
My Mobiler won't install because I can't unlock the phone to allow it to install. I ordered a screen from eBay.
hmm i didnt know it wouldnt install when locked. Does it go to locked after a restart.
Yeah, that's the first thing I tried.
I've been looking at the instructions on taking it all apart. It is a little bit intimidating, but I suppose I've done worse.
Lots of Screws
I had to replace the screen on mine a while back. It is actually pretty easy. There are just two things to remember
1) There are a lot of screws, remember which order you took them off in and which hole they go into
2) Nothing has to be forced apart, everything has screws or tape holding it. It is okay to take off the tape, and if the tape doesn't go back on it won't hurt anything.
The screen connects to the motherboard by a thin, flat plastic wire. DON"T JUST YANK THE WIRE OUT OF THE CONNECTOR!!!!!!!!! The connector has a little flip up on the end of it that allows the wire in and out.
Good Luck
Calis said:
My Mobiler won't install because I can't unlock the phone to allow it to install. I ordered a screen from eBay.
Click to expand...
Click to collapse
Open the slide out keyboard and type in the password! I did that one time just to see if it works. This will solve the lock portion.
Well, I got the new touch screen, cleaned the shattered bits out of the old one, cleaned it all up good...changed it out, put it all back together...I must not have gotten the cable seated right.
Also, as for typing my password on the keyboard...no password.
Final update:
I got it to work.

How difficult is to take apart an HTC Ozone?

Hi all,
My wife spilled a glass of beer on my PDA, and now the top front buttons don't react like before. Sometimes you don't hear the 'click' and you can feel like they got stuck.
The keyboard looks fine, so the problem is only the with the top buttons at the front of the PDA.
Have anybody tried to take apart this PDA? Would be easy to open it and clean everything before putting everything back?
Thanks a lot
I completely soaked my Ozone about a week after I got it... knocked it in the sink. I like to think that I was among the first to void my warranty, Lo..l?
The phone is really well constructed for what you need to do. All of the critical electronics are very well shielded on the board, nothing difficult about separating the board from the case.
Six 'star drive' screws on the case (that's where the warranty sticker is), one tiny phillips on the board - board pulls up off of pins, away from the usb connector and Bob's your uncle. The keypad is not fastened to the case, pull it right out.
Watch the ribbon cable for the lcd - I would not recommend disconnecting it. there should be enough play to allow you to work. Make sure you're working in a really clean environment, and check the inside of the plastic lcd cover obsessively right before reassembly. If you're anything like me that one little catpet fiber or cat hair or whatever the hell will drive you to take the phone apart again 4 days later...
Sorry about the ramble... it's late. Short answer is: Nothing to it.
Good luck!
Thanks a lot for your post. It was really helpful.
I will probably try it this weekend.
I'll post here the results
Cheers
So if I wanted to buy a different color keypad (dont like the green) it shouldnt be hard to take apart??...I change screens in Env/Voyagers a bit so have a little knowledge...

Broken Digitizer Help

Hi
I damaged my digitizer on my Touch2, I have ordered a replacement part and it has arrived.
I have stripped the phone down now, but I am stuck as to how to get the screen out.
I don't want to use too much force so any pointers as to how I can get my screen out and replace the digitizer will be greatly appreciated.
Paul
Dude, the only thing i got in my mind is youtube, there you can find anything. Try writing the something like Change digitizer on HTC Touch2 and may be you will find it, good luck
I've looked on u-Tube and found nothing for the Touch 2.
Was hoping someone on here might have more information.
Still no luck on this. Anyone?
I replaced many digitizers on blueangel and always used razor blade to seperate the lcd frame from the digitiser. The only issue was soldering the digitiser in to the lcd ribbon cable as they are soooooo thin, never opened the touch 2 yet but I can imagine its probably all cramped in there
I successfully changed my digitalizer.
I used book to help myself with added book.
Code:
www[dot]mikechannon[dot]net/PDF%20Manuals/OSeven%27s%20Disassembly%20Guide%20to%20the%20HTC%20Touch%20-%20Elf%20.pdf
Firstly, remember what you do, photograph your phones "guts" if you wnat
I, like in other video tutorials, started with removing 4 screws, after that gently half-opened corner gap between silver and front side and put in that gap plastic thing which came with digitizer.
When successfully lifted back off then you gonna see main board. In top right corner there is little screw which comes out hard in my situation. An you have to take off LCD connector wire (in left side) and digitizer connector (in left top corner). Don't forget after change of digitizer to put them back like they were or you will have to disassamble again !!!!
After doing that GENLEY lift main board off of screen. BE CAREFUL. YOU Have to pull of that black sticker on right side on board which connects from volume control to main board. Don't forget to put it back.
So you have the front side on your hand. Now push gentley but hard it from inside out. It is glued with some kind of glue. It seems it won't come but it comes (in that book it is showed).
So change your digitizer to new one and put everything back together.
You are done. Sorry I don't have pictures because it didn't came in my mind to picture it
I hope this tutorial will help you.
This is not for the Touch 2 but thanks for the help.
Still nto replaced it yet, phone is in bits in a box.
http://www.pdacenter.ru/razborka/htc_touch2_t3333/
Tutorial is in Russian.Just look at the pictures.
greetings
not sure
Sent from my generic using the XDA mobile application powered by Tapatalk

Disassembly of Legend (advises & some help required)

Hi there,
I broke my touch screen and tried to replace it by myself.
To make a long story short, I failed miserably (I broke the screen under).
However, I learned a few things I didn't met in the forum.
A- Disassembly of the case.
1- The Legend is glued. So, you have first to use hoven to melt the glue before being able to do anything useful.
15min/ 60 degree in the oven. Or use an hair dryer (I used the former).
2- Don't forget to remove ALL the screws (even the one behind the IMEI notice).
3- Don't try to open the camera lid before loosening the glue or you'll damage the aluminium body.
4- You have to unplug all the différent cables, so take notes to remember where all of them goes.
5- You must disassemble all the boards. There are 2 boards. One supporting the sim / SD connector, and one supporting the screen/touchscreen.
6- When disassembling the screen board, remove it by pulling the touchscreen at the bottom, and lift it up. don't pass a tool on the sides to remove it or worse, under the touchscreen, you'r tool will touch the screen under and break it (like I did). The screen is very, very fragile
Now, I'm stuck here because I can't remove the connector of the legent which is passed under the shield on the back of the screen.
I'm not able to remove the screen so I would like to know how to remove this shielding or get back the touchscreen connector to be able to replace it.
Once I figure out how to remove this shiled, I may be able to remove the screen too.
But now, I'm clueless (it was 2 in the morning when I gave up).
Maybe, some of you knew the trick to open this phone further.
I'd like to hear about it.
A little up to my post for the ones who did not read it till the end:
I can't remove the connector of the legend which is goind under the shield on the back of the screen.
I would like to know how to remove this shielding or get back the touchscreen connector to be able to replace it.
Once I figure out how to remove this shield, I may be able to remove the screen too.
But now, I'm clueless (it was 2 in the morning when I gave up).
mate it sounds like you have trashed your phone.they are built NOT to be taken apart.They require special tools and process to be repaired. The only thing i would suggest is contacting your insurance company and let them know that your phone was crushed under a car or something and then crush it under the car and you can get it replaced. If you dont have insurance, take some out and make a claim in say a month or two.
Its not an honest thing to do but your phone sounds busted and its the cheapest way of replacing that handset.
Post a pic of it if you can
Unfortunately, I have no rights to post a link or some put some pics.
Something about spam and profile that should be reviewed before being able show any pics.
This device is glued. No specialized tools are able to open it without removing it.
That would mean that the phone cannot be repaired, only replaced. My phone's motherboard was replaced, so at the service stations they should have special tools.
Fixed it!
Bottom right hand corner:
Bend the shielding back just enough to allow you to slip the connector in & then use a little glue to stick it back.
Maybe I was lucky, but my phones working as good as new again
I fixed my Legend
Guys, I know it's been a while since you talked but in case someone else is looking for this info, that's what happened to me:
I cracked the display of my legend and purchased a new one on eBay (roughly 40 pounds) - obviously delivered from Hong Kong but a genuine Samsung (in case you didn't know the Legen's screen as well as most of the AMOLED screens are Samsung's).
Then I used the above information plus some YouTube videos to give myself an idea as to what should I do. The result follows:
I used a hair dryer to heat up the back of the phone (camera and loudspeaker cover). Perhaps I should have been more patient as in the end I decided to use a knife with a very thin blade to lift it and I scratched the plastic and the aluminium body a bit. Anyways - the back clicks in but is glued in addition to that so you have to use both the heat and gently applied force.
Once you remove the back cover (which took me the longest out of everything) you should start removing screws. There's two behind the back cover and six behind the bottom cover (where the battery is). At this stage you don't have to remove all the screws - the bottom two, the one behind the IMEI and the one under the VOID sticker hold the main board but the two screws sitting deeper inside the phone's body hold the front buttons so you may leave them for now.
Now comes the trickiest part so read carefully: the main board is held inside the unibody by the screws (which we already removed), but is also glued right below the camera lens and along the sides. You should probably heat it up as much as you can and for a long time. I decided to do it the hard way. My dislplay was already cracked and it's the most delicate part of the phone so I said "whatever" and used the same knife as before - moved it alongside the screen (pushed it in gently from the front) until there was no resistance (the glue let go). Then I pushed and I heated the thing up and pushed and tried from every angle until finally the board slid out of the unibody. I hope you'll find it easier then I did as it seems that everyone describing it found it quite doable.
Now everything becomes easy-peasy. Remove the remaining screws to put the buttons aside (you'll have both the actul buttons and the tiny board with sensors - the latter sticks to the screen but once you remove the connectors, yu can take it off too). All the connectors are quite easy to remove if you hav a needle or something (just pull them out gently). I didn't worry about noting which is which as ther is practically no way you can mix them up - they're very different.
The rubbery plastic black surrounding of the board clicks in, so once you find the right spots you can lift them gently and take the thing off. You'll be left with the display covered by the shielding from the top and a thin metal board from the bottom. You have to remove two more screws to disconnect the main display plug.
And the final bit (that's where the thread's author had a problem I believe). My display was cracked but the shielding - fine. These two are glued together so I had to find some space for my finger nail and lift the shield. By slowly and gently pulling it apart I detached one from the other - and had to do the same thing with the metal board. Don't forget there's some extra stuff to remove from the back of the display - they're all glued but the glue will remain fresh enough for you to glue them again - this time to the new screen. The same applies to the front shield. I hope you won't let any dust sit on it in the meantime. You should have a screen protector on your new display if you bought it like I did. Remove it now and the display will be happy to stick to the old front shield just as if it was always there. The metal back will also fit in.
Now you can go through the above process backwards - just remember to connect all the connectors.
What I didn't do: I didn't use ANY glue putting the phone back together. As an effect the front shield is sticking out a bit (doesn't sit in the unibody tightly). It doesn't affect the phone itself but it gives you the funny feeling that something isn't 100% right. But I prefer that than screwing something up with a misuse of glue (glue can be disobedient).
The most important piece of information: the phone is working 100% correctly as if it was never disassembled by an amateur. Apart from two scatches on the back, the VOID sticker missing, the front sticking out slightly (less than a mm) and the missing battery slider (which I forgot to put back in and didn't bother to repeat the whole process for the sake of it) - there is nothing wrong with the phone. So if you ever crack you ever crack your Legend's screen - you can try fixing it yourself if you have the courage.
I would like to see some photos too But I'm never gonna take my phone apart - can't see the point
Foto's
Nice thread, i myself am wondering, if a better gsm antenna can be fixed inside the phone. and connect them to the 2 connections.
Do you have any pictures of the inside housing etc?

loose buttons but not something to worry about!

What a story!!
I bought a galaxy note 4 right on launch day first thing in the morning. Ive had just about every phone but have been waiting for a while now to get my hands on the new note 4.
I ended up buying the phone at the St . Bruno shopping center in Quebec, Canada and once i singed all the papers for my contract and got home, I finally open the box and took the phone out of the box. I loved it, it did everything one would expect from the highest end phone on the market.
A week later however, I started noticing that my buttons, especially my home button were slightly loose and my phone was also developing a weird oil spot under the home button.
So I went back to videotron but this time at St. Catherine street corporate branch store and the manager there obviously didnt know much about phones because he looked at it and proceeded with putting windex on a paper towel and wiping my screen with it and than told me that theres nothing wrong with it.
After frustratingly explaining everything to him, he told me that if the phone makes calls and works, than these issues arent covered for any kind of exchange as its not affecting the functionality of the phone. My logic tell me however that if one buy's a ferrari and realizes that the paint is f-up, wouldn't the dealership do something about it??? Anyways, without any luck I eventually left disappointed.
The following week After exhaustive attempt to solve the matter with Videotron to no avail, I found out that there was a store here in montreal called Service Absolute which is a samsung repair center that I could bring my phone to. I called them first to not waist more of my time and was than informed that yes they could help me but that it could take nearly a month before they would have any parts for this phone.
So after patiently waiting, I finally got a call back from them and droped off my phone the following day. I only had to wait two days before i got my phone back and thought that the turn around time was great! Only after few minutes of playing with it however, I noticed that the phone's new screen which now didn't have the oil spot was actually lifting from the housing about 1mm at the top of the phone and that the buttons were all still loose.
Its easy to imagine at this point how infuriated i was with all the time spent dealing with a phone that should of been right in the first place.. All the waiting, calling and runaround I got only to get a phone that was now even worst!! I could actually see inside my phone and behind the screen. Dust was starting to get inside the phone and under the camera lens and so on and I was really starting to freak out and was completly desperate to fix this issue asap to prevent things from getting worse and worse.
So I decided at this pont to take matters in my own hands and use my old trusty screwdriver to take this thing apart and get
To the bottom of the loose buttons and screen seperation.. I know! Scray [email protected]$ but it had to be done because at this point I needed a working phone for work and nobody seemed to help me. So after watching a few youtube videos, I unscrewed the screws at the back and gently seperated the phone from the metal frame with my fingers.
The whole assembly came out of the metal frame the same komd of way the old HTC phones used to. After doing so, the first thing i found out was that if your going scatch your phones metal frame which makes up most of the phone outer surfice, it's no big deal as it can be swapped out for around 40 to 50 bucks.
Next I noticed that all the buttons (volume and power) aren't adheared to the frame but only clipped in with a few pins stratigically placed. So its normal that they have play and wiggle. They're not gonna break and we're likely engineered to be this way. The wiggling is not really important as it won't affect anything on the phone's motherboard.
The next thing I noticed was that the glue between the inner midframe (the part that holds the motherboard to the screen assembly) also wasn't glued properly and was able to gently seperate it from the lcd/digitizer assembly without a heat gun or anything.. after doing so, the home button fell out and was simply dangling from its flex cable. It wasn't actually glued in place or held in with clips or anything. It's only connected to a flex cable on the left side of the button but thats it. I was easily able to pull it out and inspect it. It was built to be completely free floating between the midframe and the screen.
Which means that again, no need to worry about anything breaking as the home button is not a solidified part to start with and only in place where it is because of the space tolerence engeneered in the screen's home button whole. So it being slightly loose is normal and something that will eventually happen to all note 4's sooner or later. The slight looseness actually makes sense to me as any dust material that will get in between the home button wont get stuck as as much as if the space toleren was less. In my opinion, I thik that iPhones have less issues like this as the home button is part of the screen assembly and is also round.
In the end, I wasn't able to adhear the screen back in place as I didnt have double sided tape but manages to send it back to samsung and get it serviced again. I clearly asked them to fix it properly this time and it looks like they finally did and glued it back properly now.
This was a crazy experience and all I can tell you is that I definatly got an up close look of this phone and decided to keep it afterall as it's still better than a refurbished one and also because it's super easy to repair if anything ever broke on it.
Anyways i know this is a long post but I thought I'd share my experience with everyone and put some of your worries to rest.
Cheers!

Categories

Resources