Database Users

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

Artemis doesnt`t start

please help! I have made a wrong ROM Update for my Artemis. The result is that it doeasn`t starts anymore. I see only the start screen no more. If i make a SW or HW reset tahn i see a 3 colored screen and USB. But i don`t get a connection via usb to my compute`! How can i wake up my Artemis ???

tell use more what did you do and how did you do it?
what artemis is it?
what rom was it

Flash went sour..
You need the original ROM which was on your device when you bought it. What version (HTC, MDA, etc..) and what language was the original ROM?

please i need help too
I guess I made the same or a similar mistake that dr.moppi did. My machine is a Dopod P800 from mainland china with the chinese operating system. I flahsed it with PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap. Don't really remember what the original ROM was but now when i turn it on it freezes when it lights up. On the screen, it says
IPL 1.27.0001
SPL 1.27.0000
GSM 02.67.90
OS 1.28.0.0
DOPOD
I don't get a connection through usb to the computer either. I am not sure if I did the hard reset correctly. Didn't understand the instruction on that "press the soft key left and right and soft reset at the same time." Anyway, you guys are all experts, can you help me please?

it should be the same as my problem
if i remeber than i used the same ROM Update :-(
I hope anyone could give us a solution, please.

@dr. moppi we can only help you if we know what version you had before.
@empathyvirus you have to look for the original ROM which, in your case, should be the Chinese Dopod ROM. Install that one and your good to go.
Without the original ROM the only thing left to do is: sending your device to your provider or contact and sent it to the guys of imei-check. Either way, you'll probably have to pay to get it fixed.

how to install original rom
Thanks for your quick reply Pyth. In the case I get the original ROM from somewhere, how do I install it if I can't get a connection between the phone and my computer? Can you advice?

Put your device in bootloader by pressing the record button and reset at the same time. If you have your USB-cable connected between your PC and your phone it will indicate a connection by 'USB' in the left corner of your device. Now you should be able to run the ROM executable and update your device.

thanks anyway
i tried but it didn't seem to work. anyway, i have troubled you enough and maybe it's best i just go to the repair centre of dopod and pay for a fix. i really appreciate your help though Pyth.

Where can i find the t-mobile rom its the MDA Compact III that wont start for me

Help! My XDA Exec aleatory stops in a black screen after soft reset!

Hi!
Please someone can help me?
I have a O2 XDA Exec with a SDHC 8GB...
I'm the second or third user that own this device. Because this, I don't know about roms upgrades with precision, but it's running WM5.
All was work fine... But some days ago, it was stopping in a black screen when I perform a simple soft reset...
I tryed remove the battery, all the cards (include the simcard), but the problem still there...
I tryed a hard reset, but the problem still there...
I tryed all that I know, but the problem still there again...
Trouble details:
The O2 XDA Exec aleatory freeze in a black screen after soft reset.
I persists pressing Reset key with some seconds intervals, untill it (aleatory) turn on the screen and load WM5.
The Bootloader and the HardReset screens comes normaly when calleds.
When I perform a hardreset, immediatly happen an freeze without the new system never was loaded before.
I disassembly the device and test the RESET key... there is no problem.
My big suspect is something corrupt in device's bootloader or other "BIOS" program.
I use many PDAs for a long time (8 years ago), but never see nothing like that...
Seed someone something like this before?
How can I solve this problem?
Can someone help me please?
Thanks a lot.
P.S.lease, excuse my poor english...

wfreed said:
Hi!
Please someone can help me?
I have a O2 XDA Exec with a SDHC 8GB...
I'm the second or third user that own this device. Because this, I don't know about roms upgrades with precision, but it's running WM5.
All was work fine... But some days ago, it was stopping in a black screen when I perform a simple soft reset...
I tryed remove the battery, all the cards (include the simcard), but the problem still there...
I tryed a hard reset, but the problem still there...
I tryed all that I know, but the problem still there again...
Trouble details:
The O2 XDA Exec aleatory freeze in a black screen after soft reset.
I persists pressing Reset key with some seconds intervals, untill it (aleatory) turn on the screen and load WM5.
The Bootloader and the HardReset screens comes normaly when calleds.
When I perform a hardreset, immediatly happen an freeze without the new system never was loaded before.
I disassembly the device and test the RESET key... there is no problem.
My big suspect is something corrupt in device's bootloader or other "BIOS" program.
I use many PDAs for a long time (8 years ago), but never see nothing like that...
Seed someone something like this before?
How can I solve this problem?
Can someone help me please?
Thanks a lot.
P.S.lease, excuse my poor english...
Click to expand...
Click to collapse
Have you tried to install another ROM? with a different Bootloader
Battery?
Check the Wiki, there is a lot of usefull info there
Good luck

Hi, orb3000!
Thanks for your very quick answer!
Are there real chance this solve this kind of trouble?
Suggest someone a good, quick and stable WM5 rom to I try?
Are bootloaders upgradibles without need all rom update??
I'm trying understand what is happen. All we knows no erros are acceptable in ROM (firmware) upgrade... so...
Can someone explain to me how is made the XDA Exec (HTC Universal) boot routine??
Eg: In x86 PCs, first it load the bios, the bios load the setting that said to PC where is HD, the bios load the Master Boot Record with partition table, the partition table said to bios where is the active unitie with FAT, the active FAT said to bios where is the boot file, the bios said to processor load boot file to the ram and execute, etc.
Thanks!

wfreed said:
Hi, orb3000!
Thanks for your very quick answer!
Are there real chance this solve this kind of trouble?
Suggest someone a good, quick and stable WM5 rom to I try?
Are bootloaders upgradibles without need all rom update??
I'm trying understand what is happen. All we knows no erros are acceptable in ROM (firmware) upgrade... so...
Can someone explain to me how is made the XDA Exec (HTC Universal) boot routine??
Eg: In x86 PCs, first it load the bios, the bios load the setting that said to PC where is HD, the bios load the Master Boot Record with partition table, the partition table said to bios where is the active unitie with FAT, the active FAT said to bios where is the boot file, the bios said to processor load boot file to the ram and execute, etc.
Thanks!
Click to expand...
Click to collapse
Hi
here you can find one: http://forum.xda-developers.com/showthread.php?t=409966
The other questions I am no the master, so let´s learn form them
Cheers

Thanks a lot all yours!!
I solve my trouble reflashing my WM5 rom...
I used the Jwrightmcps Crossbow ROM Update 2.12.08 WWE, very fast and very stable WM6 rom! Realy a amazing work by our friend Jwrightmcps!
Including, I want suggest here that all those that still suffering in WM5 (living slowly with crashes, troubles, crashes, more troubles and this poor and slow system), try reflash your HTC with a rom like this... my device reborn!! It was dead more now is alive!!! And much more fast and stable! Before it is slowly my old Jornada 720 (206MHz), but now it realy seems have 520MHz!
Thanks a lot for all.
The link for this excelent work is HERE:
Jwrightmcps Crossbow ROM Update 2.12.08 WWE
(Download the apropriate rom to your device, folow the instructions and EnJoY!! Be HaPpY!!)
This rom don't supports 8GB SDHD cards, but download and Install 2 cabs below and it will support it:
CAB01 - SDHC_DRIVERS_FOR_C550_AND_N560_BY_GreateVK_AND_Fre ePK.cab
CAB02 - Signed_Storage_Settings_App.cab
Special thanks to big_quads for this solution!

imate jasjam error flashing pls help

hi anyone pls help,
i have one imate jasjam, the initial problem is i done a hard reset and the phone reboot and it wont finish running the customise application installation, after that the phone cant detect network, i had run a hard spl into the phone and then try to flash a rom that i download from forum but it only run 11% then stop then i realise that the rom i flash is for htc jasjam not imate jasjam, now my phone can only stay at the boot loader mode, i also try different rom but no luck so i think i ask for your help
here is my device details at the boot loader mode
IPL-1.04
SPL-2.10.01ipro
before i flash it i also cant find any radio rom version in this phone so i guess the radio rom also missing or what just not sure....
i think i flash the htc jasjam wrong model rom even now i flash back the original JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship this error message come out "ERROR [260]: update error" and it ask me to check my usb connection.
i search the forum and few member advice me to use mtty and i did tried that many time it didnt work, another member advice me to use this method "Formate yr memorycard & Unzip attached file in your memorycard named Hermimg.nbh & put yr cell in boot mode & follow screen instructions..........this illl boot yr celll out to boot mode......... " i tried that but the phone always stay at boot mode and no other instructions came out at all so im really lost and just hoping somebody can help me solve this problem...
can anyone pls guide me step by step of how to flash this phone back to normal, your help is much appreciated, many thanks.

Hi, i had the same problem flashing from the SD card. Are you using Vista or Windows7? I tried with Vista Format card, drag and drop renamed image onto sd card. Stuck it in the phone, reset and like you say hangs on bootloader. Then i tried the same thing from my Windows XP laptop, exactly the same format, rename drag and drop and everything works fine. Hope this helps

first i tried with vista then i tried with xp the problem still there, any other idea to solve this problem? thanks anyway for your advice

roms?
G'day, I've only really been reading about roms and these phones for only a few hours but I'm pretty sure that htc jasjam and imate jasjam are one and the same phone i think the said rom are used with all hermes type phones..
thanks and sorry for my ignorance if i'm mistaken

[Q] OS Deleated

Dear,
I have DOPOD 818 pro, i tried to upgrade my ROM version, and unfortunately the connection between PC & Mobile was beaked on the mid of the process, and now my fone goes dead. can any one help me to recover my fone?? i tried HARD RESETT also, but no result come, Quick response will be highly appropriated.