Related
I read a couple of threads before trying my first backup (Solved - 3.1 Update & OTA Full Package) Seemed simple enough. My tab is a July build with Acer_A500_4.010.07_Com_Gen2 purchased in the US. I checked the OTA full package thread and that ROM wasn't available, so I thought I'd back up the stock ROM and see if it was useful to anyone.
I Downloaded and installed:
Iconiaroot 1.3
Root Checker
Acer Recovery
File Manager HD
Did the backup according to the thread.
Rebooted. At that time I decided address the update the system was prompting me was available. I tried to unroot as was advised in some posts and got the message: "Something went wrong you are still rooted.
Tried to root again and the program hung on "Extracting"
Shut down, removed the SD card and restarted.
Checked with root checker and it said I was not rooted.
Tried update several times and it failed about 1/4 through the process each time, so I just reset the tab.
The update still fails.
Do I have a problem or is this just typical of the update service?
Thanks
JohnnyDingo said:
I read a couple of threads before trying my first backup (Solved - 3.1 Update & OTA Full Package) Seemed simple enough. My tab is a July build with Acer_A500_4.010.07_Com_Gen2 purchased in the US. I checked the OTA full package thread and that ROM wasn't available, so I thought I'd back up the stock ROM and see if it was useful to anyone.
I Downloaded and installed:
Iconiaroot 1.3
Root Checker
Acer Recovery
File Manager HD
Did the backup according to the thread.
Rebooted. At that time I decided address the update the system was prompting me was available. I tried to unroot as was advised in some posts and got the message: "Something went wrong you are still rooted.
Tried to root again and the program hung on "Extracting"
Shut down, removed the SD card and restarted.
Checked with root checker and it said I was not rooted.
Tried update several times and it failed about 1/4 through the process each time, so I just reset the tab.
The update still fails.
Do I have a problem or is this just typical of the update service?
Thanks
Click to expand...
Click to collapse
Did you install the recovery clockwork? If so then install the stock recovery back on the tablet use acer recovery for that.
mjd1975 said:
Did you install the recovery clockwork? If so then install the stock recovery back on the tablet use acer recovery for that.
Click to expand...
Click to collapse
Thanks a lot. That worked perfectly. I don't know how I failed to pick that up, I read so many threads my head was about to explode.
Any ideas on threads you might have read that explain where the recovery files are stored, how to identify stock, what they actually contain and the recovery process in general?
Thanks again.
Dear all,
I got a update notification today. I was so happy to see that.
I spent 20 mins on downloading this firm, but after the unzipping procedure,
it exit Andriod OS and reboot to a DOS-like system.
I saw a bee on the screen, there was a ProcessBar under this bee.
When the process went to around 20%, the process was failed and a "!" was shown up.
I installed Acer Recovery Installer on my tablet and I have Recovery on it as well.
Is it the reason why I cannot update my OS?
Help!!!!!
Easier way to get official OTA updates from acer is to be full stock :
- stock rom
- stock recovery / bootloader
Remember that updating to stock 3.2 will makes you lose root
franva said:
Dear all,
I got a update notification today. I was so happy to see that.
I spent 20 mins on downloading this firm, but after the unzipping procedure,
it exit Andriod OS and reboot to a DOS-like system.
I saw a bee on the screen, there was a ProcessBar under this bee.
When the process went to around 20%, the process was failed and a "!" was shown up.
I installed Acer Recovery Installer on my tablet and I have Recovery on it as well.
Is it the reason why I cannot update my OS?
Help!!!!!
Click to expand...
Click to collapse
Must remove root and all mods and reflash stock recovery. Maybe not all, but that should work.
shaun298 said:
Must remove root and all mods and reflash stock recovery. Maybe not all, but that should work.
Click to expand...
Click to collapse
Are there instructions on how to do this?
Update 3.2 failed
Hello, I have the same problem, I can install the stock with CWM? if so, where can I download? the ROM?
(sorry for my bad english)
My device is Acer Iconia Tab A501
I am having quite a bit of problem updating my A500. After the update downloaded the first time, it gave me an error saying update is invalid. After that it is constantly trying to download. As soon as 357 MB is downloaded, instead of asking me whether to install now or later, it just goes ahead and tries to re-download all over again. As you know it takes some 20 mins to get the whole 357MB over wifi, so I went ahead and unchecked the automatic update checkbox in system update. Does anyone know where the downloaded file ends up? I could just try to run it from that location.
My system was rooted, but once I got the last ROM update (3.1), the tablet was unrooted and none of the rooted apps work anymore. So I don't think I should be having root related issues unlike some of you who are having problems. Any help is appreciated.
Fix for "Invalid Update" problem .....
Samaruf,
I suggest that you have a look at Post #4 in the following thread......
http://forum.xda-developers.com/showthread.php?p=18132338#post18132338
This thread appears to be focused on a different problem. The resolution to your problem is at the above thread. Good luck....
So first of all my tablet is brand new and not rooted and I don't want to root it.
When I got it I could update it instantly from 3.0.whateverwastheversionatthetime to android 3.2 (build 7.006.01_COM_GEN1) but it won't go from there to 3.2.1 which I hear is available for my location (France) The update tool tells me that my firmware is up to date.
I've tried a factory reset as advised by Acer customer care services but it wouldn't change. Also no matter what I do (empty cache etc.) the market won't update to Google Play Store and I think the two issues are related.
So I have two (or rather 3) questions:
1) Does anyone know a way around to force the update? (I doubt it's possible but hey "l'espoir fait vivre")
2) If not can I install a stock ROM without root and NOT compromise the warranty?
3) Where can I get such a ROM? I have searched here and here but 3.2.1 is not on the first thread and the links on the second thread are broken, plus I want to make sure that the ROM is the proper one for my region and that comes the ICS OTA update I will have no troubles doing the update.
Thanks in advance to those who will answer.
lunaticwraith said:
So I have two (or rather 3) questions:
1) Does anyone know a way around to force the update? (I doubt it's possible but hey "l'espoir fait vivre")
2) If not can I install a stock ROM without root and NOT compromise the warranty?
3) Where can I get such a ROM? I have searched here and here but 3.2.1 is not on the first thread and the links on the second thread are broken, plus I want to make sure that the ROM is the proper one for my region and that comes the ICS OTA update I will have no troubles doing the update.
Thanks in advance to those who will answer.
Click to expand...
Click to collapse
1) No you cannot force an OTA
2) It depends - others have reported returning there acer with no probs -, i think someone has even returned it rooted and been ok. These things are fairly bulletproof, and really hard to 'brick'. As long as you can read, follow a few steps you shouldnt have any probs. The worse thing you can do is try 2 or 3 different methods all at once because something isnt working right. You're best to pick one and stick with it, if you have probs ask for help in the thread you got the rom from or start your own like you have here
3) The update.zip method from the first link you posted "should" work. Did you "decrypt" the file you downloaded before extracting the update.zip??
You could try timmyDeans v4 method- it will install a stock 3.2.1, it is rooted but you can remove root using the tools he provides. Beware though this will wipe all data so backup anything essential.
The update.zip method will leave your data and settings intact
As always the choice is yours, there are some really excellent custom roms out there - I enjoy the best of both worlds with a backup of my trusty stock 3.2.1, I flash to my hearts content knowing I can always go back to it when the OTA update is out!!! Oh the joys of root priveleges
Thanks for your input, I'll make sure to try all this when I get back from work. I've a few additional questions:
1) If I install a custom rom, will the OTA work from this ROM or, comes the OTA, will I have to restore my actual Stock rom and then proceed with the OTA?
2) I haven't tried the rom on the first link I gave because it is modified and I was searching for the original, pristine, untouched stock ROM for 3.2.1
I've seen such roms around here on xda for 3.2 but none for 3.2.1, if anyone stumbles upon one please let me know.
3) Since I'm still looking for a pristine ROM before trying anything else, I have a friend whose tablet (same brand and model) safely updated to 3.2.1, is there a way to make a rom from is gear? If yes, how to?
4) (related to 3) how can I backup my actual ROM, do I have to be a root user to do so?
THX again!
lunaticwraith said:
Thanks for your input, I'll make sure to try all this when I get back from work. I've a few additional questions:
1) If I install a custom rom, will the OTA work from this ROM or, comes the OTA, will I have to restore my actual Stock rom and then proceed with the OTA?
2) I haven't tried the rom on the first link I gave because it is modified and I was searching for the original, pristine, untouched stock ROM for 3.2.1
I've seen such roms around here on xda for 3.2 but none for 3.2.1, if anyone stumbles upon one please let me know.
3) Since I'm still looking for a pristine ROM before trying anything else, I have a friend whose tablet (same brand and model) safely updated to 3.2.1, is there a way to make a rom from is gear? If yes, how to?
4) (related to 3) how can I backup my actual ROM, do I have to be a root user to do so?
THX again!
Click to expand...
Click to collapse
1. Typically, most people do not take OTA's when running a custom rom, as basically the OTA installs a totally fresh factory Rom. This is true with the 3.2.1 update, which contains a new bootloader. Usually, this means you lose root, and Recovery, then stuck with downgrading to get these things back.
Timmy Deans root tool supposedly maintains a back door method, which s supposed to protect root, in case of an OTA. No, I haven't used this method, as I run my own 501 roms.
2. Vache has a thread "full package and updates" in the 500 Dev forum. There are several factory Roms and Updates. You'll have to look. Chances are, he may not have the specific Com Gen version you want, but probably one close enough.
3. If your friend can get adb running, you can pull a "system dump", which will dump all files/folders in the system folder. The boot.img would be nice to get, but you can probably use the current one you have. Unfortunately, he already rebooted, so you probably can't get the original full update file. If he's rooted, you can use an app called Rom Factory, to get most of what you need. It's always a good time to become familiar with ADB.
4. Well, you can back it up internally, but it's sort of useless if you can't get into your OS You will need to Root, and install a custom recovery to keep your backup externally.
Moscow Desire said:
2. Vache has a thread "full package and updates" in the 500 Dev forum. There are several factory Roms and Updates. You'll have to look. Chances are, he may not have the specific Com Gen version you want, but probably one close enough.
Click to expand...
Click to collapse
ok, as Moscow has pointed out, in vaches thread not all roms are listed. My stock roms (1.016.01 and 1.139.04) for instance weren't - so I spent the last hour or two trying the "EUU gen1" listed at the bottom of the page. Well, it actually worked!! It gave me an OTA to 1.139.04 straight away. After that installed i got the 4.010.40 to 3.2 and then the next 2 for 3.2.1 - 7.006.03 and 7.014.15. So its given me the correct updates for my country AND kept my data and settings too.
SO, since you're on a Gen1 Rom this should work for you too, but still no gaurantee you will get the OTA to 3.2.1, no harm in trying though
btw timmydeans method is a gen2 rom so you can rule that out...
---------- Post added at 11:25 PM ---------- Previous post was at 11:16 PM ----------
just came across this link for an update to stock 3.2.1 build 7.014.14 here - orignal thread here but you need cwm to install it....
unless you can make it into an update.zip???
but thats way outta my league,
moscow may be able to suggest something though
Thank you very much, your answers help a lot! Just a few precisions and I'll stop being a pain in the ass!
1. Typically, most people do not take OTA's when running a custom rom, as basically the OTA installs a totally fresh factory Rom. This is true with the 3.2.1 update, which contains a new bootloader. Usually, this means you lose root, and Recovery, then stuck with downgrading to get these things back.
Click to expand...
Click to collapse
==> @ Moscow, when you say "lose recovery" does it mean I lose the green thingy with gears when I start with volume down and power pressed/ and when I reset to factory settings?
==> @dibb_nz your method is the closest to what I'm looking for, I also hope it will give me the correct updates for my country and since Vache is a fellow countryman it might just be ok.
Anyways thanks again, I'll give a thorough look to all of your solutions and try and do a few things tomorrow afternoon. I'll keep you posted in case this thread interests anyone else.
lunaticwraith said:
==> @ Moscow, when you say "lose recovery" does it mean I lose the green thingy with gears when I start with volume down and power pressed/ and when I reset to factory settings?
Click to expand...
Click to collapse
No, what I meant to say, is when you run a rooted "custom" Rom, and use a "custom" recovery such as RA Recovery or CWM, getting an OTA update, usually wipes that out, and installs the factory bootloader. Your factory recovery....cough cough.... will still be there.
If you are only concerned about stock factory, then don't worry about it. You;re ok. Your factory/stock recovery will be just fine
The reason we root and install custom recoveries, is so we can do 3 primary things.
1. Flash a custom rom
2. Create a complete system backup to our external SD card.
3. Get rid of pre-installed useless apps.
There are other things we can do with it, but these are the primary reasons.
When you have a default factory stock system, the only protection you have, is a factory reset (hope it works), and a couple other methods which require a touch more knowledge.
Anyhow, don't worry about your factory recovery. It's just fine.
1) Just for the sake of knowledge what's the difference between GEN_1 and GEN_2? (and GEN3 and CUS7 and EMEA_TMLP)?
2) @Dibb_nz when you tried with the stock rom from Vache, was it because you encountered the same no FOTA update problem as I did? Or just to try...?
3) Something's still unclear to me after browsing through the forums: If I get an unmodified stock ROM can I flash it with the stock recovery? (so without rooting) Or do I need CWM (so root is needed)
4) What's EUU? (on Vache's thread some roms are listed as EUU)
lunaticwraith said:
1) Just for the sake of knowledge what's the difference between GEN_1 and GEN_2? (and GEN3 and CUS7 and EMEA_TMLP)?
2) @Dibb_nz when you tried with the stock rom from Vache, was it because you encountered the same no FOTA update problem as I did? Or just to try...?
3) Something's still unclear to me after browsing through the forums: If I get an unmodified stock ROM can I flash it with the stock recovery? (so without rooting) Or do I need CWM (so root is needed)
4) What's EUU? (on Vache's thread some roms are listed as EUU)
Click to expand...
Click to collapse
1. The Gen's usually signify regional based roms. More specifically language support, sometimes a wifi tweak, and maybe a couple other things. Mostly though, ComGen1's are for the US and probably canada, and offer about 12 different languages. TMPL is for East Europe mostly, with polish as the default language. All roms contain the english language as far as I know.
3. You basically can't install a full rom on an unrooted tablet without CWM or RA Recovery. You will have to run the update (decrypt the file, remove the update.zip)
4. EUU is a pc based install. Plug in the USB, set your tab to APX mode and run the EUU.
If you did the root, and install a custom recovery, then you could run just about all the full roms. Your custom recovery would be overwritten, and you would lose root access. You would have a stock tablet with the version rom you selected.
You can always wait a week or so. Am sure if the update has been pushed to your country, it's just a matter of time till you get it. It's common for the update process for specific roms, to get fully done in 2-3 weeks. It took well over a week just for users in california to mostly start getting updates.
Well the official release date for the ICS FOTA in France is May 3rd, so I'll wait until then but having other options and the know-how to take actions is always a good basis. (plus I'm really not the patient type ^^)
Stupid question but I'm guessing EUU needs root too?
and also APX means rebooting while holding power and volume - right?
lunaticwraith said:
Well the official release date for the ICS FOTA in France is May 3rd, so I'll wait until then but having other options and the know-how to take actions is always a good basis. (plus I'm really not the patient type ^^)
Stupid question but I'm guessing EUU needs root too?
and also APX means rebooting while holding power and volume - right?
Click to expand...
Click to collapse
I tried the EUU just to see if it would keep me on my regions OTA upgrade path.
Sometimes you can have probs OTA'ing if you aren't using the rom from your region.
But in this case it gave me the correct OTA's.
APX is Acer Download mode, where the OTA upgrades are flashed - this EUU will do it via your PC. Button push method (power/reset button) not required.
No, the EUU does not need root which is why I tried it out for you
You will need to be on 3.2.1 before you will receive the ICS update
I used this EUU from vaches thread -
EUUs_SBK_Acer_A500_1.016.05_COM_GEN1
late for work will check back later
That's really helpful thanks I'm downloading the same EUU you used and will try it today or tomorrow depending on how much time I have, will keep you posted!
Ok so I did the EUU install and it worked fine, the tablet then allowed me to upgrade to 3.01 and then 3.1 then 3.2 via FOTA without any problem. But once I reached 3.2, the update tool informs me that there's no update available and my gear is up to date
So my guess is Acer France are not pushing the 3.2.1 FOTA update anymore...
Any other explanation?
lunaticwraith said:
Ok so I did the EUU install and it worked fine, the tablet then allowed me to upgrade to 3.01 and then 3.1 then 3.2 via FOTA without any problem. But once I reached 3.2, the update tool informs me that there's no update available and my gear is up to date
So my guess is Acer France are not pushing the 3.2.1 FOTA update anymore...
Any other explanation?
Click to expand...
Click to collapse
Glad to hear u got thru the EUU process OK, not so great u still can't ota to 3.2.1
Others have reported similar issues not sure if/how they were ever resolved. As moscow posted earlier,ota,s are not made available to all users in all regions, all at once, so it may be just a matter of waiting for the next "push cycle" to roll round.
At least you know you can always get back to stock if you ever decide to root and go custom There no direct root method for 3.2, just use that same euu to get back to 3.1 and use iconia root and Acer recovery installer from the market and you're ready to flash your rom of choice
Pls post back if u do get the ota - best of luck
rgds Donna
Yeah I was just browsing the XDA forums, contemplating the idea to rollback and root and then installing this
I wonder if it's worth waiting for the OTA... as for what you said about waiting for the next "push cycle" I've been waiting since I got the tablet and the update hasn't come yet, which is strange because the ICS update is due on May 3rd in France and I'd guess they'd have everyone up to date and ready for the update by now!
Rooting seems pretty straightforward and much easier than what it was on my Samsung Galaxy Spica: I found this
, a file called iconiaroot.apk on the sdcard aswell, rebooting your tablet while pushing the volume down button so its starts flashing the buggy honeycomb version.
Then start up the tablet again, rush to the market, download some file manager, with that filemanager explore your sdcard, and install the iconiaroot.apk file, once thats done, rush back to the market and download and install acer recovery installer. At that point you will have CWM (clockworkmod) installed.
Click to expand...
Click to collapse
is that all there is to it?
In any case I'll keep you posted just so it can help anyone with the same issue!
alsoe FYI and just for the anecdote: the reason I'm so cautious about everything and scared ****less of rooting is that the tablet is a present from my girlfriend for my 30th birthday, and she'll hang me with my guts if I brick it.
Ok I rooted and flashed the above-mentioned rom and it works! I'm now under 3.2.1!
Thanks to everyone who helped me! When the ICS update comes I will post here to signal how the FOTA went.
Thanks again!
Lol, good onya for taking the plunge! Yeh acer recovery installer is brilliant, along with iconia root, makes the whole process stress free.
Will be interesting to see if you get a notification for ICS OTA with that rom.
Can always flash one of the leaks if u get impatient??
Glad everything's worked out and yr g/f still talking 2 u
rgds Donna
thx! I will post here when/if I get the OTA. and my love life is safe thanksnto iconia root
okay so the ota has been rolling for over a week and a half now and still nothing for me
After the OTA update to ICS on my 3.2.1 Gen 2, U.S. a500 (unrooted and unaltered at the time), my accelerometer seemed to stop working. (The curious thing about this is that the accelerometer will work only if i reset with a paperclip).
Factory Resets don't seem to do anything.
I want to go back to 3.2.1 HC, and then reinstall the ICS update, how do I do this? I am currently rooted on ICS via blackthunder.
Sazavar said:
After the OTA update to ICS on my 3.2.1 Gen 2, U.S. a500 (unrooted and unaltered at the time), my accelerometer seemed to stop working. (The curious thing about this is that the accelerometer will work only if i reset with a paperclip).
Factory Resets don't seem to do anything.
I want to go back to 3.2.1 HC, and then reinstall the ICS update, how do I do this? I am currently rooted on ICS via blackthunder.
Click to expand...
Click to collapse
Couple options;
1. check out some of the custom Roms which may have stable working accelerometer.
2. Use blackthund3rs apxflash tool in my sig 2 go back, I not done it but I'm sure if u asked on the thread sum 1 will help out.
Our builds hc 7.014.15 have not recd an ota yet, which may bode well for thinking that Acer may be working on a patch to fix the issues in the first release. All conjecture of course
_________________________________________________
Jazzyjames method here on how to roll back ICShttp://forum.xda-developers.com/showthread.php?t=1516012
he uses timmydeans v4 zip to roll back...it was for the ICS Leak version but dont see any reason why it wont work on stock -
please someone correct me if i'm wrong about this.......
things you need for this to work:
timmydeans v4 zip its about 400mb (the mirrors can be slow and erratic, if you want it i can pm you a better link)
Acer Drivers from Acer Support Download Page
a pc running win7/vista ideally, xp is a bit flaky
dot net framework 4 installed on yr pc
terminal emulator from the market
Your cpuid which you can try getting now - the downgrade wont work without it
open terminal emulator app
and type in dmesg > /mnt/sdcard/dmesg.txt
open the text file and look for androidboot.serialno=
this is your cpuid - write it down and keep it safe!!!!
you also need to enter download or apx mode manually via button combo, this can be tricky and can become
extremely frustrating!!! It involves pressing and holding in the reset and power buttons in just the right way
....but full instructions are given.
thats pretty much it, most of the process is done via your pc -
the cpuid and getting it into download mode are the most difficult part
there are on screen instructions all the way through to help you
i've attached an image of a "cannot detect your iconia screen" which you
need to get to first before you can enter download mode....some people have had real trouble getting this to come up -
but only because they're weren't following the instructions to the letter....
oh and it will WIPE YOUR DATA so backup what you don't want to lose......
You will end up with a Stock Rooted 3.2.1 gen2 with CWM
whatever way you decide Good Luck
Hi everyone.
Just repeating again - the model I have is A501 on stock 3.2.1 Honeycomb - a more USEFUL tablet with 3G and WIFI capabilities...One would think it would be a much more popular model, but the A501 doesn't have its own board on XDA; its merged with this board for the less practical A500. Basically, I have created this thread as I don't want to take any 'extra' risks in successfully installing ROOT with the CORRECT ROM with the most updated version of Android available for this tab, for example Jellybean...
Another A501 user, beny9 posted:
http://forum.xda-developers.com/showthread.php?t=1745550
Following TimmyDean's method (thank you) I have now managed to install 3.2 Honeycomb A500 ROM with success after completing steps 1-15 inclusive from his README file. As you will know, I don't have 3G or GPS functionality, so I need a stock A501 ROM to install.
I have found:
http://forum.xda-developers.com/showthread.php?t=1113878
Is my best bet to install Acer_A501_1.309.02_4.031.24_COM_GEN1 : http://cdn.a1.futuredial.com/Acer_A5...2_35b68c5d.zip from that above link, which will keep me on HC 3.2 but now, it will be the ROM for the A501? As it seems the only other NEWER Acer updates for ICS are A500 only...
Can someone link me the a fully detailed video or post on here on installing the ROM i mentioned above (if that's the best one to go with, given what I'm on now; A500 3.2 and still keeping root), or to install some other A501 ROM which is for at least Jellybean or ICS?
http://forum.xda-developers.com/showthread.php?t=1828876
Per this link, shoukd i just use the update.zip (for the 3.2 HC A501 ROM) put it on the SD card then boot up holding POWER + VOL DOWN until the file auto-installs?
http://forum.xda-developers.com/showthread.php?t=1099673
Before I can try the above, I also have trouble after i download the ROM's zip file when I try to unzip. I have downloaded the Acer Update Decrypter, but AVG antiVirus will not allow me to run the EVE file even as an administrator. What should i do?
Thanks
RoOSTA
Your best bet is to install a good 501 HC 3.2 and get on HC for your 501.
The files are available. What you'll probably want is a full HC Update rom for the 501. Note that some of these Acer roms are encrypted, so you'll need to decrypt it first. You can find the decrypting tool in the Themes and Apps forum, as a "Sticky". After decrypting, you can pull the update.zip out of it, and copy to Ext SD (do not extract, just pull the update file out). Boot the tab holding Vol- and PWR I believe. Might be Vol+ but I can't remember. This should force the tab to look for update.zip on your SD and install it.
I would use this one;
Acer_A501_1.309.02_4.031.24_COM_GEN1
After it installs, and you get it set up, you need to get Acer Update Enhancer from the Play Store. This will allow your tab to get the ICS OTA.
Keep in mind, there is only 1 official ICS OTA update for the 501, so don't expect more. It may do it in 2 steps though.
If you want root on ICS, there is really only 1 way to get true root and adb system remounts. And that's to flash the V8 unlocked ICS Bootloader, and flash an insecure boot.image. There's currently a small package that'll give you somewhat root, but it's a pain and really doesn't do a good job. So it's better to get the V8 and unsecure boot image. Might be a good idea to also install CWM Recovery at the same time.
Get the correct rom installed first, then check back if you need help.
Oh yeah, one more thing. When you are on HC 3.2, get your UID number and write it down somewhere. You need this as a safety precaution. There's a good sticky thread on how to do it. Pretty simple really.
MD
Ugh. I have a pain in the A$$ version of AVG...even under advanced settings there was no disable options. Managed to figure it out to run the Acer Decrypter EXE and fix the image you have advised I should download and flash. Will give that a go now...
Thanks again!
Just to fill you in, this issue is solved.
1. Used TimmyDeans rollback V4 tool to a 500 rom
2. SD card was not recognized in CWM or Stock recovery. Was however recognized in the HC OS.
3. Formatted SD Card using Mini Tool formatting app. Format primary partition only to fat32 (defaults)
4. Decrypted and pulled update.zip from this 501 HC full update rom
Acer_A501_1.309.02_4.031.24_COM_GEN1
http://forum.xda-developers.com/showthread.php?t=1816560
5. Did OTA update to 3.2.1
6. No more OTA available, even after installing Acer Update Enhancment tool.
7. Downloaded and used Blackthund3rs Bootloader management app
http://forum.xda-developers.com/showthread.php?t=1622425
8.Downloaded V8 and CWM package, unzipped to the same folder as the tool
9. Ran the 500NVFlashapx app.
10. After completion, booted to CWM recovery, wiped and formatted, and install Moscow Desire's RaptorX almost stock ICS rom.
Works as advertised.
MD
Yep. All thanks to MD's patience and assistance throughout these steps..
Moscow Desire said:
Just to fill you in, this issue is solved.
1. Used TimmyDeans rollback V4 tool to a 500 rom
2. SD card was not recognized in CWM or Stock recovery. Was however recognized in the HC OS.
3. Formatted SD Card using Mini Tool formatting app. Format primary partition only to fat32 (defaults)
4. Decrypted and pulled update.zip from this 501 HC full update rom
Acer_A501_1.309.02_4.031.24_COM_GEN1
http://forum.xda-developers.com/showthread.php?t=1816560
5. Did OTA update to 3.2.1
6. No more OTA available, even after installing Acer Update Enhancment tool.
7. Downloaded and used Blackthund3rs Bootloader management app
http://forum.xda-developers.com/showthread.php?t=1622425
8.Downloaded V8 and CWM package, unzipped to the same folder as the tool
9. Ran the 500NVFlashapx app.
10. After completion, booted to CWM recovery, wiped and formatted, and install Moscow Desire's RaptorX almost stock ICS rom.
Works as advertised.
MD
Click to expand...
Click to collapse
Acer A501 OS refreshment
Moscow Desire said:
Your best bet is to install a good 501 HC 3.2 and get on HC for your 501.
The files are available. What you'll probably want is a full HC Update rom for the 501. Note that some of these Acer roms are encrypted, so you'll need to decrypt it first. You can find the decrypting tool in the Themes and Apps forum, as a "Sticky". After decrypting, you can pull the update.zip out of it, and copy to Ext SD (do not extract, just pull the update file out). Boot the tab holding Vol- and PWR I believe. Might be Vol+ but I can't remember. This should force the tab to look for update.zip on your SD and install it.
I would use this one;
Acer_A501_1.309.02_4.031.24_COM_GEN1
After it installs, and you get it set up, you need to get Acer Update Enhancer from the Play Store. This will allow your tab to get the ICS OTA.
Keep in mind, there is only 1 official ICS OTA update for the 501, so don't expect more. It may do it in 2 steps though.
If you want root on ICS, there is really only 1 way to get true root and adb system remounts. And that's to flash the V8 unlocked ICS Bootloader, and flash an insecure boot.image. There's currently a small package that'll give you somewhat root, but it's a pain and really doesn't do a good job. So it's better to get the V8 and unsecure boot image. Might be a good idea to also install CWM Recovery at the same time.
Get the correct rom installed first, then check back if you need help.
Oh yeah, one more thing. When you are on HC 3.2, get your UID number and write it down somewhere. You need this as a safety precaution. There's a good sticky thread on how to do it. Pretty simple really.
MD
Click to expand...
Click to collapse
I am embarking on a very crucial mission for my Acer A501 . Its tablet OS refreshment. I have spoken and written to Acer but all my pleas have fallen on deaf ears. At last i stumbled on this site and WOW ! I am downloading the Acer_A501_1.309.02_4.031.24_COM_GEN1 and will flash as per the instruction. But I am finding difficult to locate the "sticky" software for the decryption the above. can you please help me locate the same.
I really appreciate your help and thank you in advance
jonnybrave said:
I am embarking on a very crucial mission for my Acer A501 . Its tablet OS refreshment. I have spoken and written to Acer but all my pleas have fallen on deaf ears. At last i stumbled on this site and WOW ! I am downloading the Acer_A501_1.309.02_4.031.24_COM_GEN1 and will flash as per the instruction. But I am finding difficult to locate the "sticky" software for the decryption the above. can you please help me locate the same.
I really appreciate your help and thank you in advance
Click to expand...
Click to collapse
Here is the decryption tool. Located in themes and apps.
http://forum.xda-developers.com/showthread.php?t=1869505
Good Luck!
MD
Trouble installing update.zip for A501
Moscow Desire said:
Here is the decryption tool. Located in themes and apps.
http://forum.xda-developers.com/showthread.php?t=1869505
Good Luck!
MD
Click to expand...
Click to collapse
Hi MD,
I have Acer Iconia A501 tablet. My tablet suddenly showed andriod logo with exclamation mark when it was being used. Upon looking at your posts, I found the resolution which I tried. I am not expert in this all, but I tried running your ROM "41-124-01-A500-update" from one of your posts which was actually meant for A500. This resolved the issue successfully and tablet was up and running.
Then further I found full ROM for A501 as mentioned below and thought that I should try the ROM meant for the model of my tablet.
I successfully decrypted the ROM that you mentioned "Acer_A501_1.309.02_4.031.24_COM_GEN1"
When I tried to update it with the mentioned ROM update.zip, it did updated it from SD card and passed android symbol with those gears running. However, when it restarted the tablet by itself, it showed ACER logo and then it showed "ANDROID" (spelling in blue color) which kept on flikering slowly for long long time....for more than 30 minutes and did not moved further. Can you please let me know whats could be wrong?
I also tried ICS ROM, but that didn't worked (it failed). So after couple of trail and error, I moved back to A500 ROM update.zip which I knew that is installing successfully.
Can you please let me know what shall be done in case I want update.zip for A501? It will be highly appreciated if you can upload update.zip directly that I can use and that gets installed successfully.
Regards,
Muk
mukapril said:
Hi MD,
I have Acer Iconia A501 tablet. My tablet suddenly showed andriod logo with exclamation mark when it was being used. Upon looking at your posts, I found the resolution which I tried. I am not expert in this all, but I tried running your ROM "41-124-01-A500-update" from one of your posts which was actually meant for A500. This resolved the issue successfully and tablet was up and running.
Then further I found full ROM for A501 as mentioned below and thought that I should try the ROM meant for the model of my tablet.
I successfully decrypted the ROM that you mentioned "Acer_A501_1.309.02_4.031.24_COM_GEN1"
When I tried to update it with the mentioned ROM update.zip, it did updated it from SD card and passed android symbol with those gears running. However, when it restarted the tablet by itself, it showed ACER logo and then it showed "ANDROID" (spelling in blue color) which kept on flikering slowly for long long time....for more than 30 minutes and did not moved further. Can you please let me know whats could be wrong?
I also tried ICS ROM, but that didn't worked (it failed). So after couple of trail and error, I moved back to A500 ROM update.zip which I knew that is installing successfully.
Can you please let me know what shall be done in case I want update.zip for A501? It will be highly appreciated if you can upload update.zip directly that I can use and that gets installed successfully.
Regards,
Muk
Click to expand...
Click to collapse
Hey Muk, I can probably guess the ROM you installed doesn't do data wipes and such, so it caused an animation loop.
Try this one. It's an SD ROM, so it "should" wipe your Data, along with installing the ROM.
https://mega.co.nz/#!NZBlBSLQ!mOHICp7gbinkYeHCvrEz7aKXsWQjjquAWq_XC_lSQzk
As you probably discovered, Acer has pretty much removed almost all tablet ROMs. I snagged a few the other day, then checked yesterday, and they removed all from their support site.
I would guess they are getting out of the tablet business.
Also, they shut down their OTA Update servers for a few months now.
Acer A501
mukapril said:
Hi MD,
I have Acer Iconia A501 tablet. My tablet suddenly showed andriod logo with exclamation mark when it was being used. Upon looking at your posts, I found the resolution which I tried. I am not expert in this all, but I tried running your ROM "41-124-01-A500-update" from one of your posts which was actually meant for A500. This resolved the issue successfully and tablet was up and running.
Then further I found full ROM for A501 as mentioned below and thought that I should try the ROM meant for the model of my tablet.
I successfully decrypted the ROM that you mentioned "Acer_A501_1.309.02_4.031.24_COM_GEN1"
When I tried to update it with the mentioned ROM update.zip, it did updated it from SD card and passed android symbol with those gears running. However, when it restarted the tablet by itself, it showed ACER logo and then it showed "ANDROID" (spelling in blue color) which kept on flikering slowly for long long time....for more than 30 minutes and did not moved further. Can you please let me know whats could be wrong?
I also tried ICS ROM, but that didn't worked (it failed). So after couple of trail and error, I moved back to A500 ROM update.zip which I knew that is installing successfully.
Can you please let me know what shall be done in case I want update.zip for A501? It will be highly appreciated if you can upload update.zip directly that I can use and that gets installed successfully.
Regards,
Muk
Click to expand...
Click to collapse
A big thank you to Moscow. I have tried the above link but still no go.. I have seen on Acer website they have updated the OS but all Android 4.0 ICS and nothing with Honeycomb. The tablet was initially with Honeycomb. Please advice. Thank you and Best Regards.
Trouble installing ROM for A501
jonnybrave said:
A big thank you to Moscow. I have tried the above link but still no go.. I have seen on Acer website they have updated the OS but all Android 4.0 ICS and nothing with Honeycomb. The tablet was initially with Honeycomb. Please advice. Thank you and Best Regards.
Click to expand...
Click to collapse
Hi MD,
Thanks for your super fast response. I am downloading the ROM for A501 from the link provided by me. I will update you if it works in my tab.
I forgot to mention you about one message that I received once tablet is restarted. So, once ROM for A501 from SD card has performed its job successfully....that is that android symbol with gears in its tummy is successfully finished and tablet restarts. It shows "Acer" (spelling logo) and then after it gets stuck at "android" (spelling logo). Between these two, it displays two lines messages on top left corner for 2-3 seconds that the "blob is illegal - abort" and then gets stuck at "android" (spelling logo). I think this might be useful for you to identify something.
Another thing about wiping out the data, in starting when we press volume down and power button, it does display message about SD card (still not not sure about whether it might be wiping out the data or not....I believe you might be correct that it might not be wiping out the data).
Another thing, that I found in my backup is that when I purchased this tab (A501), I downloaded HoneyComb 3.2 Kernel Source Code from the Acer support site. Is this something that you can do magic with and provide me with update.zip? Please let me know....if you can do magic with this, then let me know how shall I share it with you.
Regards,
Muk
Trouble installing ROM for A501
Hi MD,
Thanks for your super fast response.
I tried downloading the ROM for A501 from the link provided by you. It downloaded it from the cloud, but at the very end it displayed message "Decryption Error". Still I tried extracting "update.zip" from the zip file, but it displayed message that the archive is corrupt and file is corrupt. Can you please check at your end and provide me with fresh link or directly with update.zip? For your reference I have attached screenshots of errors.
I forgot to mention you about one message that I received once tablet is restarted. So, once ROM for A501 from SD card has performed its job successfully....that is that android symbol with gears in its tummy is successfully finished and tablet restarts. It shows "Acer" (spelling logo) and then after it gets stuck at "android" (spelling logo). Between these two, it displays two lines messages on top left corner for 2-3 seconds that the "blob is illegal - abort" and then gets stuck at "android" (spelling logo). I think this might be useful for you to identify something.
Another thing about wiping out the data, in starting when we press volume down and power button, it does display message about SD card (still not not sure about whether it might be wiping out the data or not....I believe you might be correct that it might not be wiping out the data).
Another thing, that I found in my backup is that when I purchased this tab (A501), I downloaded HoneyComb 3.2 Kernel Source Code from the Acer support site. Is this something that you can do magic with and provide me with update.zip? Please let me know....if you can do magic with this, then let me know how shall I share it with you.
Regards,
Muk
Trouble installing ROM for A501
Hi MD,
Please read my earlier message and then read this one.
Thanks a lot....your answer about my first problem resolved everything.... (your answer was "that the ROM that I am trying to install is not clearing the data"...I verified that the ROM is clearing the cache, but not the user data. I can confidently say that you correctly identified the issue as when the ROM installation was stuck at "android"....I switched off my tablet and tried installing again the old ROM for A500 which I knew that it is working and instead of asking me to configure the tablet (i.e. time zone, date & time setup, etc.) after installation, it simply logged in and started my tablet as usual....that means that when I was trying to install ROM for A501, it was not clearing user data and was then hanging).
Now coming back to the link that you sent me in previous message, I was able to download the zip file successfully in the second attempt. I extracted the update.zip and it did not work. It showed the similar problem of getting stuck at "android". However, with your great answer that you gave me, I cleared the user data and cache manually by pressing vol up + power buttons simultaneously and then when "acer" symbol displays, releasing only power button and turning on and off the lock button. This cleared user data and cache. After that, since update.zip (that you provided) was already in my SD card, it installed the ROM and tablet works perfectly. Thanks a lot....:good:
One question, when it asked me about the zone, it had only few countries like US, UK, etc. I couldn't find Australia...is it because this ROM not for Australia? I understand that this is not an issue, but if you find anything for Australia, do send me.
Another thing, is this HoneyComb 3.2? Will 3G and GPS work in this one?
Do let me know if you can do some magic with HoneyComb 3.2 kernel source code that I have as mentioned earlier.
Regards,
Muk
mukapril said:
Hi MD,
Please read my earlier message and then read this one.
Thanks a lot....your answer about my first problem resolved everything.... (your answer was "that the ROM that I am trying to install is not clearing the data"...I verified that the ROM is clearing the cache, but not the user data. I can confidently say that you correctly identified the issue as when the ROM installation was stuck at "android"....I switched off my tablet and tried installing again the old ROM for A500 which I knew that it is working and instead of asking me to configure the tablet (i.e. time zone, date & time setup, etc.) after installation, it simply logged in and started my tablet as usual....that means that when I was trying to install ROM for A501, it was not clearing user data and was then hanging).
Now coming back to the link that you sent me in previous message, I was able to download the zip file successfully in the second attempt. I extracted the update.zip and it did not work. It showed the similar problem of getting stuck at "android". However, with your great answer that you gave me, I cleared the user data and cache manually by pressing vol up + power buttons simultaneously and then when "acer" symbol displays, releasing only power button and turning on and off the lock button. This cleared user data and cache. After that, since update.zip (that you provided) was already in my SD card, it installed the ROM and tablet works perfectly. Thanks a lot....:good:
One question, when it asked me about the zone, it had only few countries like US, UK, etc. I couldn't find Australia...is it because this ROM not for Australia? I understand that this is not an issue, but if you find anything for Australia, do send me.
Another thing, is this HoneyComb 3.2? Will 3G and GPS work in this one?
Do let me know if you can do some magic with HoneyComb 3.2 kernel source code that I have as mentioned earlier.
Regards,
Muk
Click to expand...
Click to collapse
I'm mobile right now, so can't go into big detail.
In your settings, about tablet, you can always find info on which specific OS you have. If you indeed have an A501 and the settings tells you that your tablet is a 501, then your 3g and GPS should function.
The only 2 differences between an A500 and an A501 is of course 3g. Also, they use different GPS radios. So you can install 500 Roms on a 501 and vice versa. Just the above 2 items won't work. Also, I believe I gave you a 3.2.x ROM. Getting it to ICS 4.0.4 may be a problem.
I revived my own 501 last night by putting the motherboard in the oven, but now it doesn't read my ext SD card, so I may be stuck on 3.2. Eh, no problem.
mukapril said:
Hi MD,
Please read my earlier message and then read this one.
Thanks a lot....your answer about my first problem resolved everything.... (your answer was "that the ROM that I am trying to install is not clearing the data"...I verified that the ROM is clearing the cache, but not the user data. I can confidently say that you correctly identified the issue as when the ROM installation was stuck at "android"....I switched off my tablet and tried installing again the old ROM for A500 which I knew that it is working and instead of asking me to configure the tablet (i.e. time zone, date & time setup, etc.) after installation, it simply logged in and started my tablet as usual....that means that when I was trying to install ROM for A501, it was not clearing user data and was then hanging).
Now coming back to the link that you sent me in previous message, I was able to download the zip file successfully in the second attempt. I extracted the update.zip and it did not work. It showed the similar problem of getting stuck at "android". However, with your great answer that you gave me, I cleared the user data and cache manually by pressing vol up + power buttons simultaneously and then when "acer" symbol displays, releasing only power button and turning on and off the lock button. This cleared user data and cache. After that, since update.zip (that you provided) was already in my SD card, it installed the ROM and tablet works perfectly. Thanks a lot....:good:
One question, when it asked me about the zone, it had only few countries like US, UK, etc. I couldn't find Australia...is it because this ROM not for Australia? I understand that this is not an issue, but if you find anything for Australia, do send me.
Another thing, is this HoneyComb 3.2? Will 3G and GPS work in this one?
Do let me know if you can do some magic with HoneyComb 3.2 kernel source code that I have as mentioned earlier.
Regards,
Muk
Click to expand...
Click to collapse
Hello mukapril .. may you provide me with the Honeycomb ROM which I might try ?
Thanking you and Best Regards
Trouble installing A501 ROM
Moscow Desire said:
I'm mobile right now, so can't go into big detail.
In your settings, about tablet, you can always find info on which specific OS you have. If you indeed have an A501 and the settings tells you that your tablet is a 501, then your 3g and GPS should function.
The only 2 differences between an A500 and an A501 is of course 3g. Also, they use different GPS radios. So you can install 500 Roms on a 501 and vice versa. Just the above 2 items won't work. Also, I believe I gave you a 3.2.x ROM. Getting it to ICS 4.0.4 may be a problem.
I revived my own 501 last night by putting the motherboard in the oven, but now it doesn't read my ext SD card, so I may be stuck on 3.2. Eh, no problem.
Click to expand...
Click to collapse
Hi MD,
Apologies for very long replies. Wanted to convey the message in detail how I did it so that it might help someone else like me.
Thanks for your response. I have tested it, 3G and GPS is working fine. I believe, before my tab encountered this problem, it was having version 4 which should be ICS. At that stage I didn't had any problem with my tab...I believe it was there for long time.
If you have good known ROM for ICS, please forward me I can try on my tab. If it doesn't work, then will re-install the Honeycomb that you sent earlier.
One more question....when I try to update the system from "About Tablet" in Settings, why it displays message the the "network is poor" and advices to move to better coverage? Though, I am just besides my WiFi modem and coverage is almost 100%.
And @jonnybrave: If you are referring to the ROM that I successfully installed which was sent by MD earlier, then it does not need any decryption. So you can use the link sent by MD earlier in this post. And if you are referring to the KernelSourceCode that I mentioned earleir, then it needs some kind of processing in Linux machine and then you can create some image.....this is was I know about it....sorry not an andrion guru. Please let me know what you are referring to.
Regards,
Mukesh
mukapril said:
One more question....when I try to update the system from "About Tablet" in Settings, why it displays message the the "network is poor" and advices to move to better coverage? Though, I am just besides my WiFi modem and coverage is almost 100%.
Click to expand...
Click to collapse
You get the message as do all 500/501 owners (it can change depending on version of Rom).
Acer no longer gives updates to any of their devices (regardless of age). These are otherwise known as OTA Updates. So they have closed their update servers, so now we get some "message" that absolutely means nothing.
I suppose Acer is getting out of the Android business and no longer supports anything. Nice job Acer.
As for updating to ICS (or any other version), I have a few update files. Generally though, the update files must be matched to the current version of your tablet. Sometimes you can run a "full update" and it will work.
The problem, is these tablets are getting old, and the nand memory can go bad. Running an update can cause a variety of problems such as "Stuck in APX" mode, stuck at bootloader, stuck at boot animation. Then we have to go back to the EUUS file, or an old SD ROM file. So you run the risk of doing things all over again, and the risk that it just won't work again. (I spent a couple hours last night, and was almost ready to throw it in the garbage)
For example, I'm pretty much stuck at 3.0.x or 3.2.x. I've already disassembled the tablet and put the mainboard in the oven, just to get it back to life! And after numerous attempts to get ICS on it, I've pretty much given up before it hard bricks again. In fact, I can't get a 3.2.x EUUS to work on it, so it is stuck at the 3.0.x ATT EUUS. Eh, it's my little girls tab, so as long as it gets You Tube and browser, it's pretty much ok.
Trouble installing A501 ROM
Hi MD,
I am in the same boat as you...lol...This tablet is mostly used by my daughter and as long as it is solving my daughter's purpose, we are happy
I was just curious about that message as to why that is happenning, but after your clarification, it is clear to me as to why it is happenning.
My tablet is working as normal and everything is working fine...so we are happy with what we have.
Thanks a lot!
Regards,
Muk
---------- Post added at 03:04 AM ---------- Previous post was at 02:48 AM ----------
jonnybrave said:
Hello mukapril .. may you provide me with the Honeycomb ROM which I might try ?
Thanking you and Best Regards
Click to expand...
Click to collapse
Hi Jonny,
If you are referring to the ROM that I successfully installed which was sent by MD earlier, then it does not need any decryption. So you can use the link sent by MD earlier in this post. And if you are referring to the KernelSourceCode that I mentioned earleir, then it needs some kind of processing in Linux machine and then you can create some image.....this is was I know about it....sorry not an andrion guru. Please let me know what you are referring to.
Regards,
Muk