Hello everyone. I just want to start off saying that this is NOT a question about USB charging. I know about the trickle charge/lack of voltage stipulations. This is about the factory A/C adapter and USB cord I got with my transformer.
About 80% of the time I plug in my tablet to the A/C adapter, literally nothing happens. The screen doesn't turn on while in sleep mode like normal, the battery in the bottom corner doesn't change to a little lightning bolt, and most disturbingly, my tablet will not charge. The weirdest part is that it connects to the computer through USB no problem. I can move files and such, but no charging. Any ideas?
the charger construction is marginal at best and may need to be wiggled to get a good connection. also the usb connector an be plugged into the charger incorrectly. remember the usb connectot on the supplied cord does not comply s
with the usb spec. Also chev
ch the country ac side adapter ther are also unreliable
My cable went screwy and now it only trickle charges, regardless of what it's plugged into. I've got an RMA for it, but since I have to send them the cable to get a replacement, I'll have a paperweight for a few days at least.
Are you sure yours isn't trickle charging? There wouldn't be a lightning bolt, but I does charge.....very slowly.
Unplug the AC adapter from the wall for about 20 minutes. Plug it back in. Plug in TF.
Charging now?
unplugging it for a while seems to work better than anything. I'm pretty sure there isn't any trickling going on.
You can also try using the charger for your phone if the plug is a USB type. There have been a lot of problems with these charges documented in other threads.
Unplugging it definitely isn't a solution for me. When it first started happening I could do that and after a little while it would start working properly again, but now, it has charged at normal rates in about 3 weeks. I'm going to send it in with the RMA, but I have no idea what the turn-around time is. I'm going to be without any way to charge for that time, which pisses me off just a little bit.
Related
I am on the road a lot and don't want to be carrying the HTC charger with me. For my Treo, I had a foldable USB AC adapter (.8A and 5V) to which I plugged in a Sync and Charge cable and it did just fine.
After reading all the comments about there being two ways to charge a Tilt - fast and slow, I decided to test out a retractable USB data cable with my USB AC brick. I set the option in Power to "Not charge the battery when connected to the PC." and plugged it in. Nothing. I then unticked the box and sure enough, it started to charge. As I was at 70% of the charge, I expected this to drag on, but it didn't. It took about 1 hour and was fully charged.
I'm still a bit worried about charging this way - the description of the Lil Sync cable for the Tilt says that while it might work, under certain circumstances it won't if your battery is below 30% of a charge. Has anyone seen this happen? The last thing I want is to go away for a few days and be stuck with a dead batttery.
Do I need to pick up a special cable from ppctechs or boxwave just to charge? Should I just carry the supplied charger?
I always charge my kaiser just using the sync cable and it works fine even from a flat battery. there seems to be absolutely no need to carry an AC adapter around when you can just connect it to a computer to charge.
Thanks Spooki. Just curious - how long does a charge usually take when you charge against a computer's USB?
it seems to take roughly twice as long as a wall charger but i work with PC's all day so doesn't really bother me, much easier than carrying a charger around.
Totally stock (but i don't think it matters).
Plug the phone in, orange LED comes on.
Hold it or place in on the counter five seconds later, LED is off.
Had the phone since 6/4.
Anyone else having issues?
Are you using the AC charger ? I have two Evos and one of the chargers does what you are describing. The orange LED comes on and then goes off after a while and the phone stops charging. Does it on both phones, the other charger works fine with both usb cables.
Are you using the USB charger with a computer or laptop or plugging straight into the wall with an AC charger?
This does make a difference because if you are charging with a USB + laptop combination you could be suffering from the computer going to sleep and disabling the USB ports power to conserve laptop battery life. If you are having the issue when plugging into the wall, try plugging into a computer and selecting the "Charge Only" option when your USB debug comes up. Once it does this, allow it to charge for a period of time and then turn the phone off, switch to AC power plug and see what happens.
Perhaps you had some kind of over voltage spike on the charger through the AC plug. I could see it possibly tripping something in the phone to stop taking charge to protect the handset.
Also make sure if you do use a laptop, use a USB 2.0 or better port. More power and faster connection. Gotta love it.
Your charger may not be sourcing enough current anymore (for whatever reason). I have seen the exact same behavior with USB car chargers that were only sourcing 100-150mA.
Have you tried plugging the USB cable into a modern desktop PC? (Some laptops have reduced current ports, so a desktop is a safer bet)
Its definitely a current issue. I tried to charge my phone using my bluetooth headset's wall charger, but I got the behavior you are describing. The bluetooth headset's charger just doesnt put out enough current.
Are you using the charger that came with the phone? if so, you may want to exchange the charger...
im having the same problem when i connect it to my desktop, it sees it for about 2 secs n then disappears. My computer at work has no problem seeing the phone. i wonder if i need a driver or something for my usb ports, anyone have any ideas??
tarheelsmj12001 said:
im having the same problem when i connect it to my desktop, it sees it for about 2 secs n then disappears. My computer at work has no problem seeing the phone. i wonder if i need a driver or something for my usb ports, anyone have any ideas??
Click to expand...
Click to collapse
Probably not a driver issue, but that that rail from the power supply is either undervolted (say 4.6V instead of 5V), or can't provide enough current (amperage) or both. If I recall correctly, the Evo needs 5V @ 1A (+/- 3% tolerance).
Phone not charging
my phone has been charging fine since I got it... even been using the night desk clock app while sleeping at night for the alarm with it plugged in... everything was good...
With my phone about to die today, I plug it in to the wall charger, the led/batter indicator shows that it is charging... then POW.. it says I have a low battery and it needs to be plugged in... WTH??? it is plugged in!
The only thing I did today was flash the new boot.img for the cap fix over in Toast's thread...
Weird thing now is that I took my hero battery and put it in my EVO, plugged it into wall charger, and it stays charging... So, I put my EVO battery in my hero, plugged it in, and whola... it's now charging...
Please help as I am baffled.
MILH0U5E said:
The only thing I did today was flash the new boot.img for the cap fix over in Toast's thread...
Click to expand...
Click to collapse
that's your problem right there. that custom kernel is known to have charging issues.
I'm having the same issue with my car charger consistently. Plus my AC charger less consistently. For example, I'll go to bed and plug it in, the next morning I wake up and see the phone is at 80% charge and isn't charging. At some point over night, it gave up. This is with the stock charger too.
Anyone else notice that it won't charge from a computer? (well monitor) With my Aria i ran a USB cable from my monitor at work to the phone. the monitor wasn't connected (USB) to the computer, and it would just work as a charger. Doesn't seem to work with the atrix. anyone else able to confirm?
more info. does in fact charge when connected to a computer. but due to security reasons the company does not want phones connected to the companies. That is why i was using the monitor. Going to have to look into why it doesn't work this way for this phone. or just buy a longer cable and use the wall plug.
Mines actually not charging when connected to my laptop, wall is fine. The phone recognizes that it has a usb connected, but it doesn't charge and battery state still reads as discharging.
Also wondering if this is an issue for anyone else
Mine charged extremely slow from my PC and my laptop, the wall charger does it much faster.
USB ports on a computer don't usually provide enough voltage to charge a phone as fast as they normally do when plugged into the wall. My motherboard actually has a piece of software that supposedly enables phones to charge faster when connected to a USB port, but i have yet to try such a feature.
I've had my Atrix plugged into my computer for roughly 3 hours now, and so far it's gone from 30% to 60%.
I wouldn't be the least bit concerned if it was charging slowly, it was actually lower after unplugging than it was when I plugged in, and no charge symbols appeared. But if I plugged it in the computer saw it and soon as I unplugged the message popped up saying low battery please reconnect charger, and when reconnected it went away.
But there was no charge symbol and under battery status it said discharging.
Now I just unplugged from wall charger (worked fine first time) and plugged back into laptop, its charging fine so hopefully it was a one time thing.
Ah, so thata what it is; I have had mine on here for a while now and im still at 60.
Rooted/ROM Captivate
Rooted Atrix
When i first plugged mine into my desktop computer, it wouldn't charge at all. I then installed that motosoftware that came with the phone and after it finished the phone started to charge, but very very slowly.
Every computer ive tried works fine.
But when i plug it into a wall charger(not one that came with atrix) it starts freaking out lol. "unplug to save energy!!" flash on & off 3/second...atrix charger works fine tho...lame
You need the driver off the motorola site to charge the phone from your computer.
Yea, computers work, monitors don't. I'm guessing that the USB hubs in monitors don't have enough juice, even though they did for my Aria.
I went out of town this week and made sure to grab my USB cable, but left the AC adapter at home figuring I'd just charge off my laptop via usb. Apparently not... I also tried plugging the USB cord into my iPhone AC/usb adapter with no luck. The only thing I've found is that when you turn off the Tab and connect to one of these devices, a green battery indicator will pop up showing that it is charging. Well, after about 16 hours, it made it from 15% all the way up to 48%. Does anyone know any way around turning it off to charge or why it is barely charging when it is off?
Jaydawgx7 said:
I went out of town this week and made sure to grab my USB cable, but left the AC adapter at home figuring I'd just charge off my laptop via usb. Apparently not... I also tried plugging the USB cord into my iPhone AC/usb adapter with no luck. The only thing I've found is that when you turn off the Tab and connect to one of these devices, a green battery indicator will pop up showing that it is charging. Well, after about 16 hours, it made it from 15% all the way up to 48%. Does anyone know any way around turning it off to charge or why it is barely charging when it is off?
Click to expand...
Click to collapse
Well seeing as it has a 7000mAh battery, just about any run-of-the-mill USB charger isn't going to cut it. The amperage would have higher as well. Now i would hazard that an iPad charger (10 watts) would probably work just fine vs an iPod charger.
Your laptop's USB port isn't providing enough juice to charge fully. With the screen off it will only trickle charge and very slowly at that.
You'll need at least 5 Volt 2 Amp chargers.
You can also try this:
http://forum.xda-developers.com/showpost.php?p=14890063&postcount=16
Or this:
http://cgi.ebay.com/190522553195?ru...ee-All-Categories&_fvi=1&_rdc=1#ht_3085wt_905
I've ordered both last week but neither have arrived yet. I'll report back.
You need a 5vdc supply that will provide 2A. 10W, not 5w as the previous post said. That adapter on ebay won't help the charge, it just disconnects the data line so it does not change its mode when connected to a computer. There are a lot of power supplies that will work and even more that won't, just made sure it supplies 2a. If you want to charge off your laptop then you will want a Y adapter similar to what is on usb powered hard drives but even then you will need to use 2 usb 2.0 or 3.0 ports and will provably only get 1a out.
Sent from my GT-P7510 using XDA Premium App
Hi there,
I have a big problem with charging my Galaxy S4. It only charges with my notebook USB Port, my AC-adapter does not work.
In the battery menu I can see that AC is connected, when I plug my adapter in. But charging does not work with my device.
Over USB I can charge slowly. This isn't a software problem, I have done some resets and firmware changes since the problem.
Maybe my phone got a little bit wet earlier. Could this be the problem? Can I fix this with changing the USB port part of the hardware?
colli666 said:
Hi there,
I have a big problem with charging my Galaxy S4. It only charges with my notebook USB Port, my AC-adapter does not work.
In the battery menu I can see that AC is connected, when I plug my adapter in. But charging does not work with my device.
Over USB I can charge slowly. This isn't a software problem, I have done some resets and firmware changes since the problem.
Maybe my phone got a little bit wet earlier. Could this be the problem? Can I fix this with changing the USB port part of the hardware?
Click to expand...
Click to collapse
Already Tried to replace the charging cable?
Androiders96 said:
Already Tried to replace the charging cable?
Click to expand...
Click to collapse
Yes, I tried another cable but had no success
I dunno if I can ask it here, but i don't charge over usb, i mean it just "hold" the power level for me. Is that normal ?
Is your AC outlet working ?
Having issue where S4 only charges with USB and vibrates when using AC charger
I've been having some issues with my S4. I did recently get it a little wet, but it's working fine in all cases except charging. I have my phone next to my bed charging every night. I noticed it was dead one morning, but I figured I didn't connect the charger properly. The next night I noticed it was vibrating every 5 seconds or so, but the phone had turned off due to a low battery. Very strange behavior.
I realized that it would start charging, but it would stop between 1-3 minutes. The the phone would vibrate and not charge.
I've ready MANY posts from others with the same issue and someone mentioned their phone charges over USB. Seemed odd, but I tried it and voila, my phone charged perfectly. I have many samsung cables, none of which work. It's definitely not the cable. I can plug a samsung cable into my phone connected to AC and it doesn't work. I pull the USB portion out of the AC charger and plug into a computer and it immediately and consistently charges. The battery holds its charge as expected, so it doesn't appear to be a battery issue.
I've tried the developer mode options - no luck.
I've tried bending the charging prong - no luck.
I've tried blowing out the charging port with compressed air - no luck.
I recently got an update pushed to my phone (Sprint), but I don't think it was happening right after the update. Seems like a likely software issue.
I did get my phone a little wet recently, actually it was my young children throwing water at me.
I've read so many posts and nobody seems to have a good answer for this issue. Any suggestions are appreciated.