Database Users

Help think I might have bricked my Magic(32A)

Hi,
I feel very bad asking but can you please help me with my Magic(32A) - Rogers.
Here is the story,
I bought the phone on ebay and the seller indicated that he rooted the phone before he sold me. So I thought okay as its rooted I can go to fast boot and just apply update.zip. So I did the below
1. switched off the phone
2. pressed home + power on and went to fast boot
3. did clean swipe
4. applied update.zip
It applied the custom rom(CyanogenMod 32a) and after that I am stuck on Roger's boot-up screen. So after this I removed my battery and I tried to going to fastboot and clicking Nandriod v2.1.1 restore and I get this error "E:Can't mount /dev/block/mmcblkop1". After that I did wipe and tried to apply restore but can "Error running nandriod restore. Restore not performed".
Can you please advise me of any options I have to restore my magic back.
Thanking you
FD

If you where not flashing the SPL you "should" still be ok if you can get into fastboot.
If you can just try to apply the ROM again, you might want to download another copy or different ROM (Hero maybe).
Clinton

do me a fav and power on holding down the vol down. see if you go into fastboot. if you do then you are not bricked. if so, see what your radio and spl is plus check if your (s) is off. if so you are rooted and you flashed the wrong board rom. if its on then your seller lied and you are not rooted. if so fallow the rooting guides that are posted here. if you need ne help just pm me and i will apply my skills the best i can. i want all to be rooted and experience the true right of freedom. lol. fosho. . . .

Partial hope
When I power it on and hold volume down I can get into fastboot mode and here is what I can see on the screen
Sapphaire pvt 32A eng s-off H
Hboot-1.33.2009(SAPP50000)
CPLD-12
Radio-3.22.20.17
May 6 2009, 00:17:16
Can you please advise me on what I can do next please. Is my phone rooted as it has "s-oof"? and what should my next steps be.
Thanking you
FD

ok ?. did you buy it rooted so you didnt have to do ne thing?? does it have RAv recovery or cm's recovery??

Thank you rocking_mod I was able to restore my phone. Here is what I did
1. downloaded HoFo mod to renamed it to update.zip and copied it to SD card
2. used a recovery img and did a fast boot and loaded the img
3. after the reboot did a clean wipe
4. loaded the HoFo rom from the recovery mode.
And finally now the phone works again. Enough of action for one day.
Thanks again.

freedonkey said:
Thank you rocking_mod I was able to restore my phone. Here is what I did
1. downloaded HoFo mod to renamed it to update.zip and copied it to SD card
2. used a recovery img and did a fast boot and loaded the img
3. after the reboot did a clean wipe
4. loaded the HoFo rom from the recovery mode.
And finally now the phone works again. Enough of action for one day.
Thanks again.
Click to expand...
Click to collapse
Congrats!
Always great to see when someone bring his mobile back to live

I'm guessing the ROM you downloaded was not compatible with your phone. As a side note, do NOT apply the Rogers update ontheir web site. It will upgrade your SPL to the dreaded perfect version.

I got the same error when I first apply the hofoion108.zip. I happened to press apply again somehow, and it had no errors at the second time. My phone can start with that rom later on.

I need help, i am in same situation as you freedonkey, but i don't know where to get the files you reffer to:
1. downloaded HoFo mod to renamed it to update.zip and copied it to SD card
2. used a recovery img and did a fast boot and loaded the img
3. after the reboot did a clean wipe
4. loaded the HoFo rom from the recovery mode.
The HoFo mod and which recovery image should i use and where to get it ?
My phone specs so far are:
Sapphaire pvt 32A eng s-off H
Hboot-1.33.2005(SAPP50000)
CPLD-12
Radio-6.35.08.29
Apr 20 2009, 15:30:43
ps: I am not sure, but i dont know what model is mine (i am kind of a newbie :/) i think it should be Rogers, but not sure, bought it in Portugal blocked to TMN phone company.

I also "soft-bricked" my Magic when installing a new ROM. I had wrong radio and didn't wipe before trying to install - all I was left was the HTC boot splash.
I was then, after a few days of reading & thinking, able to restore the device! I had bought it used so I had no warranty.
I used ADB to check out if the device was alive or dead. I wiped everything that was left (kernel, boot, system and userdata) and flashed new radio that would work with CM5/6. After that I flashed Amon_RA 1.71 Recovery, a 1.6 Donut ROM, gapps and new kernel. It worked! After that (for a month) I've been playing with CM6 nightlies and RC's.
If you don't want root capablities, just the original ROM, there should be good info on that. But if you do, I would recommend to follow CyanogenMod instructions from their wiki - they're helpful and easy to follow.

NaDaBrAvItChKa said:
I need help, i am in same situation as you freedonkey, but i don't know where to get the files you reffer to:
1. downloaded HoFo mod to renamed it to update.zip and copied it to SD card
2. used a recovery img and did a fast boot and loaded the img
3. after the reboot did a clean wipe
4. loaded the HoFo rom from the recovery mode.
The HoFo mod and which recovery image should i use and where to get it ?
My phone specs so far are:
Sapphaire pvt 32A eng s-off H
Hboot-1.33.2005(SAPP50000)
CPLD-12
Radio-6.35.08.29
Apr 20 2009, 15:30:43
ps: I am not sure, but i dont know what model is mine (i am kind of a newbie :/) i think it should be Rogers, but not sure, bought it in Portugal blocked to TMN phone company.
Click to expand...
Click to collapse
Can anyone give me any tip?? i don't know which file should i get for my phone :| or even where to get it .. any help would be really appreciated

kanttii said:
I also "soft-bricked" my Magic when installing a new ROM. I had wrong radio and didn't wipe before trying to install - all I was left was the HTC boot splash.
I was then, after a few days of reading & thinking, able to restore the device! I had bought it used so I had no warranty.
I used ADB to check out if the device was alive or dead. I wiped everything that was left (kernel, boot, system and userdata) and flashed new radio that would work with CM5/6. After that I flashed Amon_RA 1.71 Recovery, a 1.6 Donut ROM, gapps and new kernel. It worked! After that (for a month) I've been playing with CM6 nightlies and RC's.
If you don't want root capablities, just the original ROM, there should be good info on that. But if you do, I would recommend to follow CyanogenMod instructions from their wiki - they're helpful and easy to follow.
Click to expand...
Click to collapse
Thanks for the help kantiii, i will see what i can doo tonight when i get back home

Hey again Kantii,
I am sorry i am bit newbie, I figure out my phone is still alive sthoughout ADB as u did, but i don't know for sure how to:
1- I wiped everything that was left (kernel, boot, system and userdata)
- I actuall wiped it after i turned the phone on with Home+off buton, does that inclued kernel and system wipe ?
2- flashed new radio that would work with CM5/6
- CM = Cyanogen Mod ??? which of these files u recomend to me ? (Both radio and CM5/6 ?)
3- I flashed Amon_RA 1.71 Recovery, a 1.6 Donut ROM, gapps and new kernel
- Is Amon_RA 1.71 Recovery compatible with any HTC MAgic ???
I am really newbie about all this so I would appreciate all details! :|
thanks a lot for everything so far anyway

Sorry for long time no reply! I had not checked my mailbox!
You should wipe them in fastboot:
1. Turn your phone on by pressing back + power until you are in fastboot & see the skating droids. Another method to do this is turning the phone on by pressing volume down + power and then the back key.
2. Connect the device to your pc (make sure you see FASTBOOT USB on the phone display) and run CMD
3. type "fastboot devices" and check if your phone is plugged in correctly and you see the device ID.
4. Now you can wipe them correctly with fastboot:
4.1 type "fastboot erase [system/cache/userdata/boot/kernel/recovery all separately]" (without brackets etc, they are here to make reading easier)
4.2 Download:radio http://www.theandroidkitchen.com/fi...es/?download=Radio_HTC_PVT_32A_3.22.20.17.img
SPL http://briancrook.ca/android/3.22/hboot-1.33.2005.img
recovery http://rapidshare.com/files/387932922/recovery-RA-sapphire-v1.7.0H-cyan.img​4.3. Move the downloaded files to C:\ (and if you want, rename to Radio.img and Hboot.img and Recovery.img) so it is easier to use them. After that type "cd.." in cmd repeatedly until you are in C:\
5. Now you should be able to flash the radio, SPL and recovery images:
5.1 Type "fastboot flash radio Radio.img"
5.2 Type "fastboot flash hboot Hboot.img"
5.3 Type "fastboot flash recovery Recovery.img"
5.4 In each step wait until fastboot says it has finished - if you won't, you have to start everything again or may brick your device.
6. Now in your phone press menu to power down it. Then boot again to fastboot to confirm you flashed correctly:SAPPHIRE PVT 32A ENG S-OFF H
HBOOT-1.33.2005
RADIO-3.22.20.17​7. Now power down the device again and boot to recovery by pressing home + power.
7.1 In recovery, check that it works correctly (no lag, no crashes, functions work properly)
8. Now you can install CyanogenMod 6 and enjoy fast FroYo on your Magic
http://wiki.cyanogenmod.com/index.php?title=Upgrading_from_CyanogenMod_4.2_to_CyanogenMod_5/6
Good luck and hopefully you can restore your device!

kanttii said:
Sorry for long time no reply! I had not checked my mailbox!
You should wipe them in fastboot:
1. Turn your phone on by pressing back + power until you are in fastboot & see the skating droids. Another method to do this is turning the phone on by pressing volume down + power and then the back key.
2. Connect the device to your pc (make sure you see FASTBOOT USB on the phone display) and run CMD
3. type "fastboot devices" and check if your phone is plugged in correctly and you see the device ID.
4. Now you can wipe them correctly with fastboot:
4.1 type "fastboot erase [system/cache/userdata/boot/kernel/recovery all separately]" (without brackets etc, they are here to make reading easier)
Click to expand...
Click to collapse
Not to thread hijack, but these instructions look well suited to my situation. At step 4.1 I get the error "FAILED (remote: not allow)". How to solve?

These instructions are only for Magic, but..
Post your fastboot details, please.

Hi my magic 32b is stuck on vodaphone splash screen.no fastbiot or recovery.but chargeable via usb and has blue light too.can u show me steps to softunbrick
Sent from my HTC Desire using XDA App

Sorry, but 32b is out of my area
Try this http://forum.xda-developers.com/showthread.php?t=755903
After that, test if you can get to fastboot or hboot (fastboot: back + power, hboot vol down + power). Then report back and search the forum for further help on restoring your device with new SPL & radio & recovery & ROM
Otherwise, if these won't work you could try JTAG.
Hope this helps,
kanttii

Recovery permission denied

Hi all,
I hope somenone can help me with the following:
My phone (as it was when it came out of the box):
SAPPHIRE PVT 32B SHIP S-ON G
HBOOT-1.33.0004 (SAPP10000)
CPLD-10
RADIO-2.22.19.26I
After many months of reading about rooting etc. I took the plunge and did the following:
- installed the sdk and made sure adb was working
- fastboot recovery-RA-sapphire-v1.6.2G
- made a nandroid backup
- adb push recover to sd card
- adb shell to flash recovery permanently
- flashed Defanged base and flashed cyanogen rom
All the above worked like a dream. Tried stable rom first:
update-cm-4.2.15.1-signed and then got really exited and tried update-cm-5.0.7-DS-test5-signed. (after a wipe)
Again all this worked like a dream.
I then wanted to see how well the nandroid restore would work. So i booted into recovery and performed a wipe before the restore.
Wow this was going so well. I now had my phone back in its original state.
Clearly i was ready for more so wanted to go back to cyanogen rom.
As i booted into recovery (home button+power button) it stopped booting into recovery but instead displays a white triangle with a yellow exclamation mark and a little phone.
What have i done wrong? I can still fastboot into recovery.
I also tried reflashing the recovery but now get permission denied.
hope someone can help
Kind regards,
PS. I am now back on update-cm-5.0.7-DS-test5-signed
I used fastboot to get to recovery, wiped and reflashed. So that all works.
I just don't understand why i cant get into the recovery i flashed in the first place without using fastboot

What details say on fastboot? What SPL Radio type of phone etc . Thanks

Mod edit: not dev related, moved to general

Broken recovery image, need help fixing

Hi,
First off these forums have been a huge help since I first rooted my Magic back in August. So, a big thank you to everyone to begin with.
I tried scanning the forums to solve this new problem I'm having, but I've lost my Amon RA recovery installation and want to get some explicit help since I know if I do this wrong I'll be bricking my phone.
Here's my setup:
SAPPHIRE PVT 32B SHIP S-ON G
HBOOT-1.33.0006 (SAPP30000)
CPLD-10
RADIO-2.22.19.26I
May 27 2009 19:06:41
CyanogenMod 5.0.7 final
I had Amon RA installed up until today - an old version (around 1.3 I think) and since CM 5.0.8 was available via ROM Manager I thought I'd give that a try. But ROM Manager made me install Clockwork Recovery, overwriting Amon RA, and the installation of Clockwork failed or something. When I try to boot up into recovery, it just hangs at the green MyTouch screen.
I read the installation notes for Amon RA 1.7, but I could use some advice on how to do this without winding up with a brick. I can still boot into CM 5.0.7, but without a recovery image I don't think I'll ever update anything again since I can't do backups/restores.
The three installation options for Amon RA are:
- via fastboot: Can't use this, I don't think I have an engineering SPL.
- via adb: Can't use this, I can't boot into recovery at all
- via terminal: The BIG BOLD WARNING about not using this on CM 5.0.7 is pretty scary.
Can anyone help a brother out here? I'm stuck.
Thanks very much in advance for any suggestions or hints.

raybez said:
Hi,
First off these forums have been a huge help since I first rooted my Magic back in August. So, a big thank you to everyone to begin with.
I tried scanning the forums to solve this new problem I'm having, but I've lost my Amon RA recovery installation and want to get some explicit help since I know if I do this wrong I'll be bricking my phone.
Here's my setup:
SAPPHIRE PVT 32B SHIP S-ON G
HBOOT-1.33.0006 (SAPP30000)
CPLD-10
RADIO-2.22.19.26I
May 27 2009 19:06:41
CyanogenMod 5.0.7 final
I had Amon RA installed up until today - an old version (around 1.3 I think) and since CM 5.0.8 was available via ROM Manager I thought I'd give that a try. But ROM Manager made me install Clockwork Recovery, overwriting Amon RA, and the installation of Clockwork failed or something. When I try to boot up into recovery, it just hangs at the green MyTouch screen.
I read the installation notes for Amon RA 1.7, but I could use some advice on how to do this without winding up with a brick. I can still boot into CM 5.0.7, but without a recovery image I don't think I'll ever update anything again since I can't do backups/restores.
The three installation options for Amon RA are:
- via fastboot: Can't use this, I don't think I have an engineering SPL.
- via adb: Can't use this, I can't boot into recovery at all
- via terminal: The BIG BOLD WARNING about not using this on CM 5.0.7 is pretty scary.
Can anyone help a brother out here? I'm stuck.
Thanks very much in advance for any suggestions or hints.
Click to expand...
Click to collapse
Try holding down the menu button while booting your phone up.
Keep holding until it starts to boot or for at least 30 seconds or so.
Make sure you flash the appropriate recovery. Did you have Amon_Ra G or H version prior to clockwork?

Binary100100 said:
Try holding down the menu button while booting your phone up.
Keep holding until it starts to boot or for at least 30 seconds or so.
Make sure you flash the appropriate recovery. Did you have Amon_Ra G or H version prior to clockwork?
Click to expand...
Click to collapse
What is Menu+Power supposed to do when booting? I tried and the phone just booted up normally.
If I hold Home+Power which used to boot me into Amon RA (it was ~1.3G btw) the phone just sits at the green MyTouch bootimage screen.
Booting into fastboot via Back+Power works normally. If I had the right SPL I'd be set.
I guess the big question is, is installing Amon RA via terminal on CM5.0.7 possible yet, or are the memory problems kernel related and unavoidable without an upgrade?

raybez said:
What is Menu+Power supposed to do when booting? I tried and the phone just booted up normally.
If I hold Home+Power which used to boot me into Amon RA (it was ~1.3G btw) the phone just sits at the green MyTouch bootimage screen.
Booting into fastboot via Back+Power works normally. If I had the right SPL I'd be set.
I guess the big question is, is installing Amon RA via terminal on CM5.0.7 possible yet, or are the memory problems kernel related and unavoidable without an upgrade?
Click to expand...
Click to collapse
The problem is supposedly fixed in 5.0.8. I've personally had a couple of issues flashing the Clockwork Recovery where the recovery would seem to flash alright but it would just hang at the splash screen. I found that if you held the Menu button while pressing the power button will allow the device to boot. Afterwards, if you flash the SAME recovery a second time it will work 99% of the time.
An alternative solution would be to use the goldcard method.
Create a nandroid backup before starting
Create your goldcard (if you don't already have it from your previous rooting process)
You should now have SHIP-S OFF. This will allow you to use fastboot.
Fastboot flash the latest radio again just in case (don't want to risk bricking).
Fastboot flash your recovery (1.7.0G)
Fastboot flash your stock hboot (spl)
Reboot while holding the home button and you should be looking at your new recovery.

[Q] Is my MT3G 3.5mm bricked?

Hello all,
I've been trying to find a solution to this problem for the last 3 days, and get nowhere. About a year ago, I rooted my Mt3g LE using the unlockr's goldcard method.
Everything worked fine until 5 days ago, when some programs stopped working. So I try to get into my recovery, and it's no longer there.
Now, I boot back into the ROM, and go to ROM manager to fix permissions. I reboot again, and try to get to my recovery. Still no, so then I got into my ROM, and clicked "Fix recovery".
Big mistake.
Now, my phone is stuck at the ROM loading splash screen. I found my goldcard, tried to flash the same SPL that it was rooted with [the top one on this page](http://forum.xda-developers.com/showthread.php?t=548218)
and it tells me "Model ID Incorrect".
Then, I tried both of the other SPL's on that page, and it tells me the same thing. I checked my goldcard on my friend's phone, and it seemed to work okay.
summary= Can't boot into ROM, can't get into recovery, can't flash SAPPIMG's.
I can get into HBOOT and FASTBOOT / FASTBOOT USB on my phone.
The lastest thing I've tried is to [unroot](http://forum.xda-developers.com/showthread.php?t=665814) but it tells me "Main Version is older! Update fail!"

Try the stock recovery (power off the phone, press and hold HOME+POWER, until you see the phone with exclamation sign, then let go and press HOME+POWER again, until you see the stock recovery, might take a few presses to get to it), with this rom "6db5d4965a64.OTA_Sapphire_TMOUS_3.56.531.1-2.10.531.4_P2_release", just do a search here. Rename the file to update.zip and put it on the root of your sd. When you're in stock recovery do a wipe and then flash the update.zip. See if that works for you.
I'm in the same situation though and nothing I've tried has worked.

I did discover that I can get into ADB when it's trying to boot.
Is there anything I can do via ADB?
I've attached a logcat for any ideas.
thanks dark0,
the screen just stays at the HTC MAGIC splash, though. I left home and power pressed for 6 minutes.

If you still have root access and your fastboot is working, try flashing the amon ra's recovery through fastboot (http://theunlockr.com/2010/03/11/how-to-root-the-mytouch-1-2-and-fender-mytouch/ , skip to step 4 if you've already set up the adb on your pc), and see if that works, if you still have root, you won't be getting the "not allow" message when flashing.
From there you'll be able to flash the new rom to get out of the bootloop.

Go into fastboot mode and post here ALL info.

SAPPHIRE PVT 32A SHIP S-ON G
HBOOT-1.33.0013 (SAPP31000)
CPLD-13
RADIO-2.22.23.02
Oct 21 2009,22:33:27
HBOOT
then I try to run a SAPPIMG.nbh or sappimg.zip and both of them say Model ID incorrect! Update Fail!
dark0: all fastboot commands say "remote:not allow"

saving current ROM

Recently rooted my MT3G. I have used Root Checker to verify root access and BusyBox install.
I have ROM manager installed. I believe, I should first save the original ROM, in case I need to restore it. When I use the menu item to save current ROM, it goes to the myTouch green splash screen, then to the black screen with the triangle containing an !
At that point do I need to press a combination of keys to get into next step, or just wait? It does not seem to do anything at that point.

To add to this, in Rom Manager I first flashed the ClockworkMod Recovery. However, when I click the menu to "Reboot into Recovery", I get the green myTouch start screen and it just hangs there.

Just do a nand backup in custom recovery (clockwork, amon ra, whichever one you're using; power down the phone then press and hold HOME+POWER until you get to it), it'll save it to your sd card.

RikR said:
To add to this, in Rom Manager I first flashed the ClockworkMod Recovery. However, when I click the menu to "Reboot into Recovery", I get the green myTouch start screen and it just hangs there.
Click to expand...
Click to collapse
Sounds like recovery didn't install correctly. Try reinstalling recovery and see if that helps. You could try installing recovery from terminal emulator. If you don't have term emulator search for it in the market then follow directions here.
This method will work for clockwork also just replace the file/file name with it.

OK, I power down. Then do home+power until green myTouch screen appears, continue to hold down home+power until triangle with ! appears, then release buttons, repress home+power and it goes to original MT3G recovery. So, sounds like Clockwork recovery did not install. Will try terminal emulator install method.

OK, when I run this in terminal I get
flash_image: not found

Found something online that says flash_image is not available in HTC stock rom. I am currently running FROYO, not a custom rom.

Obtained a copy of flash_image, will put it in and try again

I have flash_image on the SD card, but can not move it to /system/bin, not even by using the terminal. : (
I wonder if the app Root Explorer could move it or copy/paste it.

How in the heck does anyone install new roms in an MT3G if you can not flash???

Do a search on how to flash recovery through fastboot (in a nutshell you'd need AndroidSDK/ADB tools and a custom recovery image, then it's just a matter of connecting your phone to pc, booting into fastboot and issuing a 'fastboot flash recovery recovery.img' through cmd), once you do, you can flash new roms.

An update on the outcome in case any one else as noob as me has these same problems. Following the rooting thread elsewhere here for the MT3G, I downloaded roottools and was able to use adb to change the permissions on /system/bin so that flash_image could be put there. Also was able to put the recovery mentioned in that same thread on my phone. Once finished, I was able to boot into the new recovery and do a backup of the phone.
So, I believe that finally has me in a position to try and flash a new rom, with the option of restoring me back to what I jave now if the new rom has issues.
I'd be interested in recommendations for ROMs to try on the MT3G. Are any of the custom ROMs preferable to FROYO which I am now running? Do any make the phone operate more "snappy"? That is my primary wish, not so much features, but responsiveness. I appreciate the help given here.

Last night I used Rom Manager to download Cyanogen 6.1.0 and the Google apps. I chose to wipe data and cache when installing. When I began the rom swap the phone rebooted to the green myTouch screen, after a while, it rebooted to the green screen, this continued until I eventually pulled the battery. Reinserting the battery and turning the phone back on only started this boot looping again. So, I pulled the battery, started up into the recovery and did a restore. Fortunately, the restore seems to have worked perfectly.
Any ideas on how to get the rom swap to go?

Sounds like you might need to flash an alternative kernel. Check your phones info (power off then reboot holding down volume down+power) to see if it is compatabile with the rom. If your device is 32b and your radio 2.22.27.08 or 2.22.28.85 flash a 2708+ kernel from here
or an autokernel from here after flashing the rom or just search 2708+ kernel, you'll find lots of options, everyone has a personal favorite.

fastboot shows this:
SAPPHIRE PVT 32B SHIP S-ON G
HBOOT-1.33.0013 (SAPP 30000)
CPLD-10
RADIO-2.22.28.25
Oct 21 2009,22:33:27
So, if I flash a 2708+ kernel, I would do that, then flash the new rom? Or, would I flash the rom, then boot back into the recovery and flash the kernel, then restart the phone?

About Phone:
Android Version
2.2.1
Baseband Version:
62.50SJ.2017U_2.22.28.25
Kernal Version:
2.6.32.9-27237-gbe746fb
[email protected] #1
Build number
FRG83D

When I flash Clockwork recovery, and see it appear when I boot into recovery, then how is it possible that later, the Android recovery comes back?

RikR said:
fastboot shows this:
SAPPHIRE PVT 32B SHIP S-ON G
HBOOT-1.33.0013 (SAPP 30000)
CPLD-10
RADIO-2.22.28.25
Oct 21 2009,22:33:27
So, if I flash a 2708+ kernel, I would do that, then flash the new rom? Or, would I flash the rom, then boot back into the recovery and flash the kernel, then restart the phone?
Click to expand...
Click to collapse
Rom first then kernel.

RikR said:
When I flash Clockwork recovery, and see it appear when I boot into recovery, then how is it possible that later, the Android recovery comes back?
Click to expand...
Click to collapse
I think it's because your still on a stock rom. Once you flash a custom one that should stop happening.

When i flashed Cyanogen 6.1.0, the phone would not boot. So, how do I flash the rom first, and then flash the kernel? Also, can you suggest a specfic kernel for my MT3G? Why doesn't the Cyanogen 6.1.0 already have the kernel i need?