Related
Right, so iv had my X10 for 6days now, the battery does drain and there is a another thread about that But,
Today using it normally, charged it this morning and throughout the day i drained the battery so its on 10% as i get home and i try to charge it but Nothing happens.
no light
no indication of charging at all
iv tried switching usb cables, also plunging it into the PC, PS3 and different outlets but the phone does not charge at all
i did update the phone through the Sony Ericsson software from the website successfully the night before if that has anything to do with it..
also i have tryd to turn off the phone then plug in the usb charger, interestingly the phone turns on without me pressing the Power button but as it reaches a point after the splash screen with the SE logo, it says please charge etc 5% left ..and as i go to check the status, it indicated the last time it was charged plugged into power was 20+ seconds ago
any help will do ..as im returning the phone to the shops tomorrow for a replacement if not a refund and nothing more,
Pull the battery for a few minutes then replace and retry.
instigator008 said:
Pull the battery for a few minutes then replace and retry.
Click to expand...
Click to collapse
I have tried that too, took out the battery for 10mins and tryd againg and no luck
..maybe it's picked up a fault after I updated through SE
Can you do a repair through SEUS app? If not it sounds like it is done for
instigator008 said:
Can you do a repair through SEUS app? If not it sounds like it is done for
Click to expand...
Click to collapse
That's not recommended if the phone has less than 50% power.
noodlez19 said:
Right, so iv had my X10 for 6days now, the battery does drain and there is a another thread about that But,
Today using it normally, charged it this morning and throughout the day i drained the battery so its on 10% as i get home and i try to charge it but Nothing happens.
no light
no indication of charging at all
iv tried switching usb cables, also plunging it into the PC, PS3 and different outlets but the phone does not charge at all
i did update the phone through the Sony Ericsson software from the website successfully the night before if that has anything to do with it..
also i have tryd to turn off the phone then plug in the usb charger, interestingly the phone turns on without me pressing the Power button but as it reaches a point after the splash screen with the SE logo, it says please charge etc 5% left ..and as i go to check the status, it indicated the last time it was charged plugged into power was 20+ seconds ago
any help will do ..as im returning the phone to the shops tomorrow for a replacement if not a refund and nothing more,
Click to expand...
Click to collapse
Just leave it on the charger for a few hours and see if it does anything (perhaps the charging indicator is just bugged :3)
instigator008 said:
Can you do a repair through SEUS app? If not it sounds like it is done for
Click to expand...
Click to collapse
all that would happend is the green light would turn on and nothing more, the pc would not even recognise the phone in that service mode
thanks for the suggestions anyway I think iv just had some bad luck on this one, just gave it a go when I woke up and it's just faulty I guess
I will be returning it to the shop now
It was just a matter of time for me to brick me new phone. It took me 8 days this time but it can be fixed fairly easy.
If you've got a red flashing led (flashing ca. once per second) while charging and flashing three times after pressing the power button, you can try the following.
I had an error like that and fixed it.
After leaving the phone at the charger for about half an hour it turned on at random but was stuck at the Sony Ericsson bootscreen. I think it has something to do with wiping battery stats, so be careful with this option in XRecovery.
This is how I got it working again:
First of all ensure your battery is not damaged. Try it in a different phone or try a different battery.
If it works, ensure your usb-port is working.
Afterwards do the following:
1. Boot up a windows computer
2. Download and install Sony Ericsson Update Service (SEUS) - you will find it easily with the search machine of your choice
3. Get some adhesive tape, press the back button and tape it down (be sure it is pressed all the time)
4. Connect the phone to your Computer, you should see the flashing LED again, don't panic
5. Start SEUS and chose the X10
6. Wait(!)
7. Get a cup of coffee and wait again
8. The LED will turn green at some time, windows will recognize the device. Complete the update of system software (even if it says your phone is up to date)
9. You will have to reboot the phone. Your LED will be flashing red again. Don't panic, your almost done. Leave the phone charging for another hour or two. It should be booting by itself.
After this steps my phone was working fine again. No dead battery, no dead usb-port as mentioned in other forums or other threads.
Just try it, if you flashed a custom rom you have got nothing to lose.
USB port disabled - factory wipe
dawn2k said:
First of all ensure your battery is not damaged. Try it in a different phone or try
After this steps my phone was working fine again. No dead battery, no dead usb-port as mentioned in other forums or other threads.
Click to expand...
Click to collapse
Thank you for this thread. I've seen many similar issues and was just hit with this RED LED of death - 3 blinks then nothing...
Messing with chargemon and charger in /system/bin/ - has certainly not been good, but I'm not convinced it was the entire problem, at least in my case I was running a version of Wolfbreak CM 6.5 v5 and let the battery get below 5% charge.
I should have turned it off, waited until I could charge again but I didn't! When I tried to recharge, the phone initially was giving green led's so it might have been possible to salvage easily.. I made a terrible mistake of going to xRecovery and waiting until the battery was so dead, there was really no way of recovering from this state and totally drained out the battery.
So I purchased a new BST-41 battery for AU $25. Maybe that was expensive for a clone, others are available for $4 on ebay but hey, have a look at this thread regarding Original VS. Fake BST-41 Battery - quite interesting!
This got my X10 working again... BUT I am unable to get into SEUS, Flashtool or make the charger work. The USB port appears to have been disabled and am unsure about the best way to reset to an operational state.
Will update this thread when I have found more
EDIT 1: It's all in the above post...
5. Start SEUS and chose the X10
6. Wait(!)
7. Get a cup of coffee and wait again
8. The LED will turn green at some time, windows will recognize the device.
Click to expand...
Click to collapse
With the exception of maybe having to mess around with this a bit, it will eventually work. I didn't tape the button down because you need to release it but I've just seen green flashes.. I'm very close to getting this phone working again with SEUS and the back key..
EDIT 2: xRecovery > Factory Reset > Full wipe - you will be warned of loosing all user data - The moment you wipe the user data, the phone will recognise the charger and turn to a green LED. From this point let it reboot, it will go silly and you may even get a WLOD - White LED of death.
If you have got USB to connect, follow the standard method of using SEUS to restore a factory ROM and take it from there. TRY to remember not to let the battery go below 5% without a charger and invest in some spare battery's from eBay - cheap after all
Connect via WiFi is only possible with LT15 (Arc) - SO-01c (Arc) - Neo (MT15) - Play (R800) - USB must be enabled for a connection to happen to the PC and this is where I'm still stuck..
EDIT 3: Turns out the problem is - USB Port needs to be re-soldered, it is broken contact and is intermittently connecting to the USB port.
This is what happened to my phone too. I ended up sending it away for repair because the USB port was broken. The phone would say it was charging but it actually wasnt. Im still waiting to get my phone back.
I thought it wasn't possible to brick an xperia x10, forgive me if I'm ring?
Sent from my X10 TripNMiUI using XDA App
shakeyabooti said:
I thought it wasn't possible to brick an xperia x10, forgive me if I'm ring?
Sent from my X10 TripNMiUI using XDA App
Click to expand...
Click to collapse
It wasn't bricked, it was faulty connection in the USB port not allowing their phone accept a charge. The red LED is from an uncharged battery.
Sent from my X10i using XDA Premium App
Thanks OP, this worked perfectly. I'm glad I risked it with an amazing deal on craigslist. Kudos.
shakeyabooti said:
I thought it wasn't possible to brick an xperia x10, forgive me if I'm ring?
Sent from my X10 TripNMiUI using XDA App
Click to expand...
Click to collapse
Only if you have access to the bootloader.
Ok.. i think i bricked my x10.
My x10 always gave me problem at startup. I had to remove battery wait 5sec. Then again try booting. After few attempts it would boot. So i decided to reinstall 2.1. Downloaded seus. Installation till 90%. And unknown error window.
Service Center won't take it as its from different country.
When i try to boot it. It blinks green led and that's it.
Any suggestions?
vu2ikl said:
Ok.. i think i bricked my x10.
My x10 always gave me problem at startup. I had to remove battery wait 5sec. Then again try booting. After few attempts it would boot. So i decided to reinstall 2.1. Downloaded seus. Installation till 90%. And unknown error window.
Service Center won't take it as its from different country.
When i try to boot it. It blinks green led and that's it.
Any suggestions?
Click to expand...
Click to collapse
Can you get in flashmode?
If so then try and flash with FlashTool
@arkedk thanks for the quick reply.
I m total noob. Can u please point me to the "how to" flash x10?
EDIT: i found this thread which discuss the flash at length.. will try and get back.
red led flashing three times
arkedk said:
Can you get in flashmode?
If so then try and flash with FlashTool
Click to expand...
Click to collapse
yes. i could successfully flash the phone with 2.1.B.0.1 version just now. without error. but now i when i try to start the phone, it doesn't. instead, i get the red led flashing three times.
i put it for charging. the green led lights up showing it has started charging. but after roughly 15-20 seconds the green led fades off.
1. flashing was successful which means usb is not broken right?
2. have i bricked my phone?
3. How can i get my lovely x10 back to life?
Have you flashed with SEUS or flashtool?
Try reflashing the rom as a first step.
If flashing with flashtool, does the sw detect your phone? Could you post the output to the screen as flashtool tries to flash? That would help!
Sent from my X10 TripNMiUI-IRIS using XDA App
acmbc said:
Have you flashed with SEUS or flashtool?
Try reflashing the rom as a first step.
If flashing with flashtool, does the sw detect your phone? Could you post the output to the screen as flashtool tries to flash? That would help!
Sent from my X10 TripNMiUI-IRIS using XDA App
Click to expand...
Click to collapse
I used the flashtool, as SEUS was the only culprit who made my x10 to hibernate (i am still trying to wake it up )
sorry, i donno how to attach photo.. here is the link where i have uploaded that.
http://www.flickr.com/photos/[email protected]/5771350239/
vu2ikl said:
I used the flashtool, as SEUS was the only culprit who made my x10 to hibernate (i am still trying to wake it up )
sorry, i donno how to attach photo.. here is the link where i have uploaded that.
http://www.flickr.com/photos/[email protected]/5771350239/
Click to expand...
Click to collapse
Looks like you had a successful flash. How much battery did you have when you flashed?
If the battery had drained dry flashtool wouldn't have finished flashing, would it though?
Can you have you tried to reflash?
Sent from my X10 TripNMiUI-IRIS using XDA App
arkedk said:
Looks like you had a successful flash. How much battery did you have when you flashed?
Click to expand...
Click to collapse
battery was very very low. but the phone is connected to laptop while flashing..wouldn't that be enough?
@acmbc: should i reflash?
when i kept x10 for charging, the green charging led lights up for 10-15 seconds and then goes off.. still kept it charging for couple of hours. and then tried rebooting. this time green led flashed. phone vibrated but nothing.
ok..i gotta confess. i tried the crazy solution mentioned on talk.sonyericsson which asked to keep battery in freezer for an hour and then try charging it. i did that. and when i put x10 for charging. for 20 seconds the green light was on.. but then it went berserk.. vibrating continuously. at once i took out the battery. and now i am scared as it is repeating this cycle when i charge it. green light->off->vibrate continuously.
vu2ikl said:
battery was very very low. but the phone is connected to laptop while flashing..wouldn't that be enough?
@acmbc: should i reflash?
when i kept x10 for charging, the green charging led lights up for 10-15 seconds and then goes off.. still kept it charging for couple of hours. and then tried rebooting. this time green led flashed. phone vibrated but nothing.
ok..i gotta confess. i tried the crazy solution mentioned on talk.sonyericsson which asked to keep battery in freezer for an hour and then try charging it. i did that. and when i put x10 for charging. for 20 seconds the green light was on.. but then it went berserk.. vibrating continuously. at once i took out the battery. and now i am scared as it is repeating this cycle when i charge it. green light->off->vibrate continuously.
Click to expand...
Click to collapse
There's your problem. You must never flash with low battery. always flash with at least 50% or more. And no you're not getting power from the computer in flashmode only the battery is supplying that power.
If the flash was successful you could try and hook the phone up to the charger (wall charger) and let it sit there for a while. This might get it back to life.
how do i charge my half bricked phone
arkedk said:
There's your problem. You must never flash with low battery. always flash with at least 50% or more. And no you're not getting power from the computer in flashmode only the battery is supplying that power.
If the flash was successful you could try and hook the phone up to the charger (wall charger) and let it sit there for a while. This might get it back to life.
Click to expand...
Click to collapse
ok.. thanks. i thought phone would get the power from computer.
but now i have one more question in front of me.
How do i charge my phone.
coz. when i connect x10 to wall charger it shows green light for some time and then starts vibrating untill i get the battery out.
if i connect x10 to the computer which i am doing now, it is flashing red light every 5 seconds.
vu2ikl said:
ok.. thanks. i thought phone would get the power from computer.
but now i have one more question in front of me.
How do i charge my phone.
coz. when i connect x10 to wall charger it shows green light for some time and then starts vibrating untill i get the battery out.
if i connect x10 to the computer which i am doing now, it is flashing red light every 5 seconds.
Click to expand...
Click to collapse
Looks like you had an unsuccessful flash then. If you got any other means of getting the battery charged then try that and see if you can flash it again.
If not, I'm afraid you'll have to take it to the service center.
I read the post from the op..
If the battery gets severely drained it may look like the phone is dead.
Just plug it in and sometime up to a hour later it will power up.
I know that you might heard of what I'm going to say tons of times but I searched the whole internet and still got no solution
I tried to update my motorola defy+ and then something went wrong, now, I'm stuck in a situation that I can't enter the
bootload or the recovery mode. all I see is a black screen(like the phone is off) and a white led above the screen(only when it's with the USB)
in added, no software on the PC do not recognize the phone when it's connected.
there's any way to solve this?
Bo0gieMan said:
I know that you might heard of what I'm going to say tons of times but I searched the whole internet and still got no solution
I tried to update my motorola defy+ and then something went wrong, now, I'm stuck in a situation that I can't enter the
bootload or the recovery mode. all I see is a black screen(like the phone is off) and a white led above the screen(only when it's with the USB)
in added, no software on the PC do not recognize the phone when it's connected.
there's any way to solve this?
Click to expand...
Click to collapse
Switch off the phone, then press vol up and then the power button. See if the bootloader comes. I'm sure you ain't doing it correctly:laugh:
hotdog125 said:
Switch off the phone, then press vol up and then the power button. See if the bootloader comes. I'm sure you ain't doing it correctly:laugh:
Click to expand...
Click to collapse
I've did it correctly, and I just did it again, nothing...
Does pressing both volume keys and holding them while you press the power button bring you to noman's land too?
Sent from my MB526 using xda app-developers app
Does your battery is charged???
Try to charge your battery.
Sent from my MB526 using xda app-developers app
cyrusct82 said:
Does your battery is charged???
Try to charge your battery.
Sent from my MB526 using xda app-developers app
Click to expand...
Click to collapse
I have the identical problem. I left the phone plugged into USB on the computer for 15 hours. No change. A wall charger does not turn the charging light (white light) on.
I have tried 3 or 4 different chargers and nothing helps.
If your system partition is corrupted it well never charge.
You must charge your battery with the MacGyver method or with another defy. Then you will be able to flash a sbf with RSD lite.
Sent from my MB526 using xda app-developers app
I'm facing the same issue after trying to install Quarx CM10 2nd Boot Build 09.07.2013. The Phone ran fine for some time and then died down. On Charging- battery would show ? when it was off so Tried the data wipe and reinstalling the ROM to the same consequence. Then wiped the system and after that disconnected the charger from AC outlet- after that- on ac charge- stuck at M Logo, and USB charging gives white LED. Able to enter bootloader with both VOL keys and power keys pressed- get message -
"motorola defy bootloader 09.10 battery low cannot program"
I'm not sure would be able to use MacGyver method, howver I can get an inexpensive universal charger to charge the battery- will it work?
Battery charger should work, and your problem should be fixed by a sbf flash
Sent from my MB526 using Tapatalk 2
thekguy said:
Battery charger should work, and your problem should be fixed by a sbf flash
Sent from my MB526 using Tapatalk 2
Click to expand...
Click to collapse
?? How exactly can he fix this problem without McGyver?? I don't see how this would be a good solution...
There's no harm in trying to charge the phone though, even though it might (will most likely) not work.
thekguy said:
Battery charger should work, and your problem should be fixed by a sbf flash
Sent from my MB526 using Tapatalk 2
Click to expand...
Click to collapse
Already tried that- defy sits on M logo on AC Charge- Same message while entering bootloader
droid_<3er said:
?? How exactly can he fix this problem without McGyver?? I don't see how this would be a good solution...
There's no harm in trying to charge the phone though, even though it might (will most likely) not work.
Click to expand...
Click to collapse
Seems McGyver is the only way forward! will try it today and update.
Thanks for all the help! appreciate it
Moto Up and Running using Mcgyver Cable!
Thanks all for the help. Could finally manage to get my defy working using the Mcgyver method.
Using the thread here http://forum.xda-developers.com/showthread.php?t=892026
sudipt123 said:
I'm facing the same issue after trying to install Quarx CM10 2nd Boot Build 09.07.2013. The Phone ran fine for some time and then died down. On Charging- battery would show ? when it was off so Tried the data wipe and reinstalling the ROM to the same consequence. Then wiped the system and after that disconnected the charger from AC outlet- after that- on ac charge- stuck at M Logo, and USB charging gives white LED. Able to enter bootloader with both VOL keys and power keys pressed- get message -
"motorola defy bootloader 09.10 battery low cannot program"
I'm not sure would be able to use MacGyver method, howver I can get an inexpensive universal charger to charge the battery- will it work?
Click to expand...
Click to collapse
droid_<3er said:
?? How exactly can he fix this problem without McGyver?? I don't see how this would be a good solution...
There's no harm in trying to charge the phone though, even though it might (will most likely) not work.
Click to expand...
Click to collapse
OP had asked whether an universal battery charger could fix the problem. Low battery error would've been obviously fixed by charging the battery via an universal charger, which I recommended, or by MacGyver method, which he had said he may not be able to do. That's why I recommended it. Since he tried to charge it the regular way by simply connecting it to a wall outlet, it didn't work.
sudipt123 said:
Thanks all for the help. Could finally manage to get my defy working using the Mcgyver method.
Using the thread here http://forum.xda-developers.com/showthread.php?t=892026
Click to expand...
Click to collapse
Glad you could fix it
New battery fixes problem
thekguy said:
OP had asked whether an universal battery charger could fix the problem. Low battery error would've been obviously fixed by charging the battery via an universal charger, which I recommended, or by MacGyver method, which he had said he may not be able to do. That's why I recommended it. Since he tried to charge it the regular way by simply connecting it to a wall outlet, it didn't work.
Glad you could fix it
Click to expand...
Click to collapse
I can confirm that instead of the McGyver method, using a new battery restores the device to being able to be reflashed. Yes, you are starting all over, but instead of a brick, your Defy is back in service.
Thanks to everyone who made the suggestions. I'm sure the McGyver method works for some, but a new battery and a $5.00 charger from eBay restored my phone.
My phone was very slow....So factory reseted it few times...This time phone not working...TOTALLY. TRied all these
hold volup + power and when insert battery. Helped for me once. If this method will not help try this
remove phone battery from defy, plug charger to socket ,but not in the phone,
Holding volup button plug charger in phone without battery
No bootloader....
Tried pluging it using usb....No reaction...HELP
ashsurawin said:
My phone was very slow....So factory reseted it few times...This time phone not working...TOTALLY. TRied all these
hold volup + power and when insert battery. Helped for me once. If this method will not help try this
remove phone battery from defy, plug charger to socket ,but not in the phone,
Holding volup button plug charger in phone without battery
No bootloader....
Tried pluging it using usb....No reaction...HELP
Click to expand...
Click to collapse
First of all, completely switch off your phone. Take out the battery, and wait for 5 minutes. Then press volume+ then power button and keep holding them. If you factory reseted then you should still have your ROM installed. What happens when you connect the phone to the charger?
hotdog125 said:
First of all, completely switch off your phone. Take out the battery, and wait for 5 minutes. Then press volume+ then power button and keep holding them. If you factory reseted then you should still have your ROM installed. What happens when you connect the phone to the charger?
Click to expand...
Click to collapse
Tried it...Still not working. Connecting to charger also no response.
ashsurawin said:
Tried it...Still not working. Connecting to charger also no response.
Click to expand...
Click to collapse
If when connected to the charger only a white LED lights up, then mostly your battery is dead. Charge it using McGyver method (search for the xda thread by sorensiim) or a universal battery charger or a new charged battery.
hotdog125 said:
If when connected to the charger only a white LED lights up, then mostly your battery is dead. Charge it using McGyver method (search for the xda thread by sorensiim) or a universal battery charger or a new charged battery.
Click to expand...
Click to collapse
I tried starting with a battery from my friend's phone...Not working..
ashsurawin said:
I tried starting with a battery from my friend's phone...Not working..
Click to expand...
Click to collapse
Make SURE your friend's phone is a Defy/Defy+. I'm pretty sure the problem is with your battery running out of charge. Otherwise you're doing the procedure to open bootloader wrong.
hotdog125 said:
Make SURE your friend's phone is a Defy/Defy+. I'm pretty sure the problem is with your battery running out of charge. Otherwise you're doing the procedure to open bootloader wrong.
Click to expand...
Click to collapse
We both got the same mobiles..defy+...And I am able to open bootloader in his phone.
Is there any change of my motherboard getting a prob..If yes, temme watto do
ashsurawin said:
We both got the same mobiles..defy+...And I am able to open bootloader in his phone.
Is there any change of my motherboard getting a prob..If yes, temme watto do
Click to expand...
Click to collapse
Then i'm afraid you may have to change motherboard. Go to any Moto service center and get it replaced, I can't help you further.
hotdog125 said:
Then i'm afraid you may have to change motherboard. Go to any Moto service center and get it replaced, I can't help you further.
Click to expand...
Click to collapse
Any idea over how much it might cost
ashsurawin said:
Any idea over how much it might cost
Click to expand...
Click to collapse
No idea. Costs maybe around 2000 Indian Rupees.
I have a dead mobile Samsung i9515. Not on at all If i connect to PC it detects as Zeus flash Device that ALL. what can be the PROBLEM !
zakiyy said:
I have a dead mobile Samsung i9515. Not on at all If i connect to PC it detects as Zeus flash Device that ALL. what can be the PROBLEM !
Click to expand...
Click to collapse
Can you go to DOWNLOAD MODE? Recovery?
If you can get into download mode then it ain't dead
Joku1981 said:
Can you go to DOWNLOAD MODE? Recovery?
Click to expand...
Click to collapse
No Cannot ENTER download MODE !!
zakiyy said:
No Cannot ENTER download MODE !!
Click to expand...
Click to collapse
Yeah, it's dead, as long as you're sure that you're doing the right thing to get into download mode.
Have you tried removing the battery, holding the keys for download mode, and replacing the battery while you keep holding the keys? Remember to let go of the power key after you feel the vibrate, or soon as you see download mode.
NO vibrate Nothing.. NO download mode !! All good battery 3.75V all Superb BUt only ZEUS FLASH DEVICE even without battery CONNECTED @
zakiyy said:
NO vibrate Nothing.. NO download mode !! All good battery 3.75V all Superb BUt only ZEUS FLASH DEVICE even without battery CONNECTED @
Click to expand...
Click to collapse
Battery 3.75v?
The battery is dead. Charged, it should be around 4.2v.
3.7 volts is empty.
The phone may still be broken, but you won't know unless you charge the battery lol. Has it been left unused for a while or something?
With lithium ion batteries, if you let them go completely flat then don't use them for a while, sometimes they won't charge. If this has happened and it won't charge inside the phone then you'll probably need to give it a 5 minute manual charge to 'wake it up'.
This actually happened to me the other week with a kindle. Had been left discharged for a while. Took the battery out, gave it a quick 5 minute hard wired charge, and it was fixed.
zakiyy said:
NO vibrate Nothing.. NO download mode !! All good battery 3.75V all Superb BUt only ZEUS FLASH DEVICE even without battery CONNECTED @
Click to expand...
Click to collapse
Ur phone is dead ... u have to dead boot repair by RIFF JTAG BOX
Stupid question. You have tried entering into download mode by voldown+power or by voldown+home+power?
Do you see charging light when charging?( Red led)
Have you tried changing cable?
Have you tried using other battery (already charged).
Try new battery with disconected usb/charging port from mainboard and with really good battery. if windows recognize wrong hardware its only because of bad cable or charging port.
adrenalinas said:
Stupid question. You have tried entering into download mode by voldown+power or by voldown+home+power?
Do you see charging light when charging?( Red led)
Have you tried changing cable?
Have you tried using other battery (already charged).
Try new battery with disconected usb/charging port from mainboard and with really good battery. if windows recognize wrong hardware its only because of bad cable or charging port.
Click to expand...
Click to collapse
What is STUPID?
Did you follow the Thread? Already told you i USed other batttery, already tried DOWNLOAD mode all. So nothing working. Now NO BOX accept this MODEl for JTAG !
Thats my stupid question.not yours So don't be angry at me..
You did not understand me.Have you tried disconect charging port from mainboard and try to boot Without it.
charging port may be faulty. disconect it to ensure it is not because of that.
I had few "dead" or not charging phones with such problem which now works after change usb connector or whole port
i have gt-19515 dead but......
adrenalinas said:
Thats my stupid question.not yours So don't be angry at me..
You did not understand me.Have you tried disconect charging port from mainboard and try to boot Without it.
charging port may be faulty. disconect it to ensure it is not because of that.
I had few "dead" or not charging phones with such problem which now works after change usb connector or whole port
Click to expand...
Click to collapse
i have my phone dead but strange action i install a rom but after odin say pass the phone reboot and don’t move away from the samsung logo i take the batterry off and try to reboot again but dont work and dont go to download mode again or charge what ur opinion pepole