Related
I have looked and done searches for this problem with no matches. Phone stuck in bootloop after battery died. Pulled battery and went to recovery, tried to restore after wiping showed error message for data wipe
E:Can't mount /dev/block/mmcblk0p1.
(file exists)
When I tried to restore the attached results show up on the screen.
Any help with this situation would be greatly appreciated.
Try installing another rom. If that doesn't work, try flashing a new clockworkmod version.
Yes, I have tried three different roms and flashing a different recovery with the same type of results. The problem seems to be with data. Everything I try to do including wiping data ends up in an error message.
Hmm. Then you might try going back to stock from hboot and rerooting
Is sd full, or nearly full?
Sent from my ADR6300 using XDA Premium App
Id start with the newest version of clockworkmod and an new SD card.
Unrooted using the RUU with reverted HTC drivers. Process seemed to go fine but when it reboots it gets stuck in a bootloop with original droid bootscreen. I still have s-off and am wary of removing for fear of being stuck.
You could try flashing super vr wipe and do it that way.
sounds like the sdcard isn't mounting. i would back up the sdcard then reformat it and try again. or try another sdcard if you have one handy i usually keep a spare around just in case.
Look up five vibe fix ...
Sent from my ADR6300 using XDA App
This kind of thing frightens me to death about flashing a new ROM. I'm dying to get that 2.3 ROM that just posed but I'm afraid of bootloops, whitescreens and error messages etc.
It's really not that bad, as long as you dont touch it while its doing it's thing it works great. I just installed Ovo Community Mod Test RC5 and it is SICK!
You need to update your hboot to .92 first though.
kzoodroid said:
sounds like the sdcard isn't mounting. i would back up the sdcard then reformat it and try again. or try another sdcard if you have one handy i usually keep a spare around just in case.
Click to expand...
Click to collapse
Sounds like something isn't mounting, but I'm not sure if it's the SDcard. Those directories are on eMMC, aren't they? Not sure if this would help, but I'd check to see if it's mounted as read/write. Looks like it's read only.
RMarkwald said:
Dude, use Doug Piston's ROM Flashing Tutorial, here. It's easy.
After the screen shot showing Wiping Cache, also do:
Mounts and Storage - format /system, format /data, format /boot
Advanced - Wipe Dalvik
Then resume at the Install zip from SD Card screen shot...
Click to expand...
Click to collapse
I followed those directions and flashed the new 2.3.4 without any issues. I was originally on 2.2 rooted with unrevoked3
Much bigger problem. Now that I have run the RUU I no longer have clockwork recovery and cannot flash anything. When I reboot I get the droid bootscreen in bootloop. Frustration!
Have you tried just booting with the sd card removed? Issues with the sd card can stop it from booting
Also if you flashed the RUU your unrooted therefore have no cm recovery. You will need to root again for that.
Yes recovery was gone, attempted to flash clockwork again. When booting into recovery strange bar appeared and screen went black. After several tries with same results flashed Amon ra style recovery and now have this recovery but am still getting bootloops when flashing and having same E: can't mount /dev/block/mmcblk0p1 (file exisits) error messages. Confident there is a solution but have no idea how to get there. Determined though! Any help is greatly appreciated.
It is saying read only file system . E:Error in CACHE:recovery/log
This is at the bottom of the recovery screen.
Ok, I've said this a few times on here, but I don't see were you've mentioned that you've tried it. Remove your SD card and see if it boots!
Got a interesting news, cant mount my sd card, dont know if the sd is broken but isnt working.
Where should i found it when i mount from clockwork recovery?
I figured out the sd issue moving big files from a folder to other while its mounted, no move taked time to complete,
everyone was instantly, like when you move in the same hard drive.
So any advice on how to get my sd working, to transfer the CM to it.
The phone hard drive mount itself on I:
On android to mount a sd is like in Linux? Its mounted in a system folder?
Need help.
I tryed to install the CM Mod, first time, got the lastest file from 31/08, rename it on update.zip
Got root on my phone, using odin and replacing kernel.
Now it dont go after the first screen (Samsumg Galaxy S ii GT-I9100 yellow triangle with black ! on center.
I tried lots, i mean, lots of re instaling the .zip but it still dont pass that screen.
Right now only things i can do in phone is power+volume up+home button and go to ClockworkMod Recovery v4.0.0.2
or power+volume down+home and go to download screen.
Trying to install several times de CM Mod i got lots of lines (like 20+) them Error (code 7) install aborted.
Right now I need anything that make my phone back, any rom, custom android any version.
I explored the backup and restore menu and i got a restore point, it give me the restore complete, but still locked on that screen.
Please .zip file that ill make my cell back.
I checked de checksum and the CM file is ok
What kernel did you flash? You need to be sure the kernel you flash is for gs2.
Sent from my GT-I9100 using Tapatalk
You probably flashed a bad rom. Simply wipe data from clockworkmod and install a zipped rom from there.
news on post
On android to mount a sd is like in Linux? Its mounted in a system folder?
YES ,is called "external_sd" .As for your problem i suggest downloading a stock ROM+original kernell on your PC (KH3 as an example) .Enter downloading mode and flash it thru Odin than use an insecure kernell to root and have CWM back on your device to be able to flash the next ROM from your internal sd (internal memory) and continue experiencing
By the way ,the flashable zipes must be on internal memory for CWM to see tham
Your post should be in Q&A section
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums and Read THIS
Moving to General
Have been running cm7 7.03 for quite some time originally installed using verygreens method with sd card cm7 installer 1.2. Decided I wanted to update to cm7 7.2 so thought I would update verygreens installer to 1.3 before updating to new version of cm7. Put update-genimage-1.3.zip on boot of sd card booted to recovery installed file and it appeared to install correctly rebooted and now I am stuck on Loading ... Any help would be greatly appreciated.
rmckeen said:
Have been running cm7 7.03 for quite some time originally installed using verygreens method with sd card cm7 installer 1.2. Decided I wanted to update to cm7 7.2 so thought I would update verygreens installer to 1.3 before updating to new version of cm7. Put update-genimage-1.3.zip on boot of sd card booted to recovery installed file and it appeared to install correctly rebooted and now I am stuck on Loading ... Any help would be greatly appreciated.
Click to expand...
Click to collapse
You do not install that zip that way. You have to unzip it to the .img file and burn to the SD with win32diskimager like you did the first time.
Sent from my Nook Color running ICS and Tapatalk
Thanks for the info. I was following instructions that indicated that I could put the update-genimage-1.3.zip on the boot portion of the sd and apply the update through cwm. I did not want to reimage my sd card as I have allot of information on it.
rmckeen said:
Thanks for the info. I was following instructions that indicated that I could put the update-genimage-1.3.zip on the boot portion of the sd and apply the update through cwm. I did not want to reimage my sd card as I have allot of information on it.
Click to expand...
Click to collapse
ok, don't know why it got stuck then. You used CWM recovery on emmc to flash it? The recovery script on SD would not install it properly.
Yes, that's correct. Now when I put the sd card in I just get stuck on screen that says loading and I have to take the card out to boot back into the nook software. I did make a backup of my emmc with cwm before I started this but I am unable to get into recovery at this time. I am not sure what my next steps should be. Start the process over with another sd card and then try and salvage the info on my original sd.
rmckeen said:
Yes, that's correct. Now when I put the sd card in I just get stuck on screen that says loading and I have to take the card out to boot back into the nook software. I did make a backup of my emmc with cwm before I started this but I am unable to get into recovery at this time. I am not sure what my next steps should be. Start the process over with another sd card and then try and salvage the info on my original sd.
Click to expand...
Click to collapse
I just read the instructions in thread and you do not use CWM recovery on emmc to flash that file. You are supposed to use the verygreen recovery script that is on the SD. By using CWM on emmc, you flashed the new recovery files to emmc and replaced CWM. That's why you can't get back in it. I think you can recover by putting the update- zip back in the root partition of the SD and trying to boot to the SD recovery. Then when you have got your SD repaired and flashed 7.2, you can reinstall CWM to emmc with ROM Manager.
Sent from my Nook Color running ICS and Tapatalk
I can certainly try that but I am now confused on which update.zip file to put on the boot portion of the sd to hopefully fix my sd card. Thanks for your help.
rmckeen said:
I can certainly try that but I am now confused on which update.zip file to put on the boot portion of the sd to hopefully fix my sd card. Thanks for your help.
Click to expand...
Click to collapse
the update-genimg1.3...zip. Be sure to boot to SD recovery and it should be ok.
Sent from my Nook Color running ICS and Tapatalk
Great thanks. Can you review for me how I make sure I boot to sd recovery. Really appreciate your help.
rmckeen said:
Great thanks. Can you review for me how I make sure I boot to sd recovery. Really appreciate your help.
Click to expand...
Click to collapse
If you have one of the newer u-boot.bin files... you hit "n" when booting up and select SD card... Recovery... that will be verygreen's recovery mode.
If you still have the original u-boot.bin from genimage 1.2 (not very likely at all... since CM7 has had new u-boot.bin's for a while now) you would have to use the old timing method of power + n for about 5 seconds.
When I try holding the n key the screen comes back with Loading ... but never moves past that screen. Actually the nook will not boot at all when the sd card is in even if I do not hold down the n key it goes right to the Loading ... screen and just hangs there. If I shut it down and remove the card it boots into the nook operating system fine. Any suggestions would be most appreciated.
rmckeen said:
When I try holding the n key the screen comes back with Loading ... but never moves past that screen. Actually the nook will not boot at all when the sd card is in even if I do not hold down the n key it goes right to the Loading ... screen and just hangs there. If I shut it down and remove the card it boots into the nook operating system fine. Any suggestions would be most appreciated.
Click to expand...
Click to collapse
I have attached a file to the board. Download and unrar this file. There should be 4 files there. Take your SD card out and put in your PC. Copy these files to the boot partition, overwriting the files that are there. Take the update-geniimg1.3...zip out and put the update- ...7.2 ...zip in. Then put the card back in the nook. Boot and while booting hold the n key. A boot menu should come up. Choose SD and recovery and continue booting. It should install cm7.2 and you are done. When in CM7, use ROM Manager to reinstall CWM to emmc.
EDit: I added a second file. Unrar and add these two files to the boot partition too.
Edit 2: Files removed after user successfully repaired SD
Transferred the files and did the update everything is running great. Thank you so much for your help it is greatly appreciated.
yes i read before posting. first let me tell you wut i did.
1) installed schizoid pac rom on nook color......
2) as per instructions i formatted system and cache.
3)flashed rom
4)worked slow but fine. decided this rom isnt worth keepin on.
5)as per instructions when transferring from these types of roms to any other 10.1.x roms i formatted system/cache again
^^^^^^^^^^^^^^^^^this last step broke my clockwork recovery. :crying:
----now i am unable to boot after rom,gapps flash.
----receive following messages when cwm is pulled up
-----E:\ unable to mount system, cache and all the other ones that u can manually mount and dismount via cwm
so i can flash jus not boot up.
tried flashing stock image .zip for a stock recovery via sd boot and i get passed *read forever* and then i hit the big gigantic "n" with copywrite details and such but won't go passed that screen.
wanted to try the adb restore thingy but i need to be able to boot up the nook to enable debug right? so i can't do that......unless im stupid which quite possibly is the case. i had a moment complaining about kit kat earlier and am sorry so if i can't get help i understand. thx guys
newbtrigger69 said:
yes i read before posting. first let me tell you wut i did.
1) installed schizoid pac rom on nook color......
2) as per instructions i formatted system and cache.
3)flashed rom
4)worked slow but fine. decided this rom isnt worth keepin on.
5)as per instructions when transferring from these types of roms to any other 10.1.x roms i formatted system/cache again
^^^^^^^^^^^^^^^^^this last step broke my clockwork recovery. :crying:
----now i am unable to boot after rom,gapps flash.
----receive following messages when cwm is pulled up
-----E:\ unable to mount system, cache and all the other ones that u can manually mount and dismount via cwm
so i can flash jus not boot up.
tried flashing stock image .zip for a stock recovery via sd boot and i get passed *read forever* and then i hit the big gigantic "n" with copywrite details and such but won't go passed that screen.
wanted to try the adb restore thingy but i need to be able to boot up the nook to enable debug right? so i can't do that......unless im stupid which quite possibly is the case. i had a moment complaining about kit kat earlier and am sorry so if i can't get help i understand. thx guys
Click to expand...
Click to collapse
Go to my NC partition repair thread linked in my signature and flash the repair and format zips. That should then let you put any ROM you want back on it, including stock.
You may have to go to my NC Tips thread to make a bootable recovery SD first though.
Sent from my BN NookHD+ using XDA Premium HD app
leapinlar said:
Go to my NC partition repair thread linked in my signature and flash the repair and format zips. That should then let you put any ROM you want back on it, including stock.
You may have to go to my NC Tips thread to make a bootable recovery SD first though.
Sent from my BN NookHD+ using XDA Premium HD app
Click to expand...
Click to collapse
thx, will try when i get off work. again thx for the response
GENIUS!
GENIUS!:highfive:
Hi. I attempted this installation this morning. I was able to install CWM Recovery using ROM Manager. I then installed the latest Build found in this forum http://forum.xda-developers.com/showthread.php?t=2459171. The installation proceeded as shown in the video, but when I reboot the phone after installation, I see the LG logo, and then the word ANDROID on the screen and nothing further. I can still get into CWM recovery by pressing Menu, Vol - and the power button, but the phone does not boot past the ANDROID screen. I ran the installation a second time, but the same result. Can anyone help?
JWinAus1969 said:
Hi. I attempted this installation this morning. I was able to install CWM Recovery using ROM Manager. I then installed the latest Build found in this forum http://forum.xda-developers.com/showthread.php?t=2459171. The installation proceeded as shown in the video, but when I reboot the phone after installation, I see the LG logo, and then the word ANDROID on the screen and nothing further. I can still get into CWM recovery by pressing Menu, Vol - and the power button, but the phone does not boot past the ANDROID screen. I ran the installation a second time, but the same result. Can anyone help?
Click to expand...
Click to collapse
I assume you are coming from stock rom as you just installed CWM, so make sure you are using the STANDARD version,from the cyanoid page and follow this :
boot to recovery
go to mounts and storage
mount usb
this will allow you to move the correct version of the rom to the sd card, if it is not already,
when finished putting the rom on the sd card, unmount usb
now go back to the main menu
wipe data factory reset
wipe cache
go to advanced
wipe dalvik
go back
go to mounts and storage
format system
go back to main menu
install zip from sd card
choose zip from sd card
go to the rom you put on the card
select yes to continue
wait for finish
reboot
If it gets stuck again pull out the battery,wait a few seconds, put it back in, boot to recovery and do everything from install zip from sd card again and see what happens
let me know if it works or not or if your cwm recovery options vary from those i listed and i can help further
JWinAus1969 said:
Hi. I attempted this installation this morning. I was able to install CWM Recovery using ROM Manager. I then installed the latest Build found in this forum http://forum.xda-developers.com/showthread.php?t=2459171. The installation proceeded as shown in the video, but when I reboot the phone after installation, I see the LG logo, and then the word ANDROID on the screen and nothing further. I can still get into CWM recovery by pressing Menu, Vol - and the power button, but the phone does not boot past the ANDROID screen. I ran the installation a second time, but the same result. Can anyone help?
Click to expand...
Click to collapse
next time pm or post in the therad
bluerichblue said:
I assume you are coming from stock rom as you just installed CWM, so make sure you are using the STANDARD version,from the cyanoid page and follow this :
boot to recovery
go to mounts and storage
mount usb
this will allow you to move the correct version of the rom to the sd card, if it is not already,
when finished putting the rom on the sd card, unmount usb
now go back to the main menu
wipe data factory reset
wipe cache
go to advanced
wipe dalvik
go back
go to mounts and storage
format system
go back to main menu
install zip from sd card
choose zip from sd card
go to the rom you put on the card
select yes to continue
wait for finish
reboot
If it gets stuck again pull out the battery,wait a few seconds, put it back in, boot to recovery and do everything from install zip from sd card again and see what happens
let me know if it works or not or if your cwm recovery options vary from those i listed and i can help further
Click to expand...
Click to collapse
Hi. And thanks, your suggestions worked and I now have Cyanoid Rom installed and working. Much appreciate your assistance.
linuxxxx said:
next time pm or post in the therad
Click to expand...
Click to collapse
Hi linuxxxx
Sorry, I can't post in the Cyanoid ROM thread, I don't have enough posts on this site, so it is not allowed. I was able to get this to work though following bluerichblue's advice above. There is one remaining issue. I cannot enter any APN settings. When I enter those, and select the save option, nothing is saved and the system returns to a blank APN list screen. You previously suggested that this may be a problem with the SIM? However, I have used different SIMs with the same result. Also, while my LG Optimus L3 was running on the Stock Rom, this function worked and I was able to setup APNs. Can you help?