Solved: See post #4
Obviously for those with a modded kernel and broken MAC.
If we knew the real MAC address for the specific device, couldn't we set the module's MAC to our real one?
Or just a MAC spoofer? But more like an un-spoofer..
Im looking for the answer as well...
I have been through every oc kernel so far, only stock/insmod seems to keep the mac addy. This might be the best option until a proper solution is found, if anyone has an idea on how to insmod on startup that would be good.
I also tried ipconfig eth0 hw ether, but got an invalid argument.
tijuanacartel said:
Im looking for the answer as well...
I have been through every oc kernel so far, only stock/insmod seems to keep the mac addy. This might be the best option until a proper solution is found, if anyone has an idea on how to insmod on startup that would be good.
I also tried ipconfig eth0 hw ether, but got an invalid argument.
Click to expand...
Click to collapse
Can't you setup a script that insmod's and set that up to run on startup?
I'm sure there is somewhere in the ROM where a script can be added for it to run on boot, or at least a boot time Android one...
init.rc perhaps?
Okay i found it... there is a file called /bootcomplete.rc that calls
/system/xbin/busybox run-parts /system/etc/init.d
so, on stock kernel with oc-dz.ko:
Code:
# cd /system/etc/
# mkdir init.d
# cd init.d
# echo insmod /system/lib/modules/oc-dz.ko pll2_l_val=74 > overclock
# chmod 0755 overclock
will load the module at boot. wifi mac is correct
Okay I've been using this for most of the day and just had a hard crash on level 99 of robo defence(F7U13!) Looking into it, it seems this kernel module only seems to step up from 700 straight to 1497! I'm disabling it for now.
Apparently cyanogen is quite a lot faster than the stock Sense, even without overclock. As soon as it hits RC2, I'm gonna give it a shot.
tijuanacartel said:
Okay i found it... there is a file called /bootcomplete.rc that calls
/system/xbin/busybox run-parts /system/etc/init.d
so, on stock kernel with oc-dz.ko:
Code:
# cd /system/etc/
# mkdir init.d
# cd init.d
# echo insmod /system/lib/modules/oc-dz.ko pll2_l_val=74 > overclock
# chmod 0755 overclock
will load the module at boot. wifi mac is correct
Click to expand...
Click to collapse
EDIT
Trying from a Terminal I get: "undable to chmod overclock: Read-only file system"
I tryed from ADB and all commands were accepted, file was created and chmod processed, but after reboot the OC module is not loaded
What ROM are your using ??
Obviously you should remount your system partition rw
tijuanacartel said:
Obviously you should remount your system partition rw
Click to expand...
Click to collapse
OMFG I really need to sleep a little
What ROM are you using ?? Have you changed the Kernel ??
at the time i was using stock.. currently using virtuous from rom manager
I've been strugglin with that command line for days, trying to find a way t make it stick from boot (and not typing it from a console), I finaly made it today via updater script (update.zip).
I also included the stock radio module and the stock kernel (rooted) to the package, so it can serve as a "rescue kit" for other users stuck with the MAC WiFi shizz. I shared it @ devs forum.
I can't post this on the original thread because of The Rules about new users being blocked from developer forums(feh), but I wanted to share the script I used to automatically update the telephony database instead of buying the Root Explorer and SQLite Editor apps. Tested on my AT&T Atrix with stock builds 1.8.3 (Android 2.2.2 Froyo) and 4.5.91 (Android 2.3.4 Gingerbread).
Install the Android SDK and the Android Debug Bridge if you haven't already.
Get a copy of the sqlite3 binary for Android (I found one in the SuperOneClick zip file)
Root your phone (one method is here). The important part is to be able to su to root in an ADB shell.
Download the attached shell script, chmod it +x (and change the extension to .sh if you fee like it)
Push the sqlite3 binary and the shell script to a temp dir on the device:
Code:
$ adb push sqlite3 /data/local/tmp
$ adb push telephony.sh /data/local/tmp
Shell into the phone (make sure USB debugging is enabled):
Code:
$ adb shell
su to root:
Code:
$ su root
cd to /data/local/tmp:
Code:
# cd /data/local/tmp
make sure the script is executable:
Code:
# chmod 755 telephony.sh
run it:
Code:
# ./telephony.sh
Select AT&T Tether APN from list (Settings->Wireless & networking->Mobile Networks->Access point names)
Reboot device
Enable WiFi Hotspot
(Optional) Raise your fist in the air as you triumph over bloodsucking corporate greed.
If things get fouled for any reason, the script makes a backup of the files it modifies in the same directory with a "_backup" extension. You can restore the original databases by running the following commands in a root shell on the phone:
Code:
# cp -p /data/data/com.android.providers.telephony/databases/telephony.db_backup /data/data/com.android.providers.telephony/databases/telephony.db
# cp -p /data/data/com.motorola.android.providers.settings/databases/settings.db_backup /data/data/com.motorola.android.providers.settings/databases/settings.db
Make sure to include the -p switch, otherwise the file permissions won't be correct. It doesn't seem to be possible to set file permissions/ownership manually ("chgrp radio" gives an error).
Okay I need help......... I've rooted and I've completely lost the ability to have free wifi tethering.!!! I've been trying to do this procedure all day long and when I try and run the script from a cmd prompt (just like this........ ./telephony.sh) it tell me I do not have permission to do that even though I've already CHMOD'd the file to give SU permission........ GRRRRRRrrrrrrrrrrrrrrrrrrr please help.
Changing the permissions on the script with chmod is just the first step.
Make sure you've shelled into the phone ('adb shell'), and then logged in as root ('su root'). The command prompt should change from a '$' to a '#' when you're logged in as root.
If you're having problems getting the script to work for you, try this method for Wifi/tether enabling, it worked perfect for me on Stock 2.3.4, as well as Ninja Speed Freak
http://forum.xda-developers.com/showthread.php?t=1160452
yes sir
Malibee said:
Changing the permissions on the script with chmod is just the first step.
Make sure you've shelled into the phone ('adb shell'), and then logged in as root ('su root'). The command prompt should change from a '$' to a '#' when you're logged in as root.
Click to expand...
Click to collapse
Iam ssomewhat familiar with linux redhat enterprise. I will try the thread below.
BRILLIANT
Brilliant now that was easy as hell thank very much! I'm posting on the newly enabled Atrix hotspot using my Xoom! THANK YOU AL!
Awesome!
Agreed, worked perfect. Immediately. Now, I'm just having trouble getting my Xoom to connect. Everything else can, except the Xoom.
Hey guys,
I have been trying to figure out how to root the RAZR M but I can't find any good instructions. I'm on the latest update. Thanks in advance!
Sent from my XT907 using xda app-developers app
http://www.droidrzr.com/index.php?/topic/5151-Root-For-Droid-Razr-M-(JellyBean-and-ICS)
Sent from my SCH-I535 using Tapatalk 2
I followed the instructions here:
http://forum.xda-developers.com/showthread.php?t=1940630
but needed to replace the SU & Superuser.apk from the rootzipfile link at http://aosp.us/?p=294 before running it.
justaq said:
I followed the instructions here:
http://forum.xda-developers.com/showthread.php?t=1940630
but needed to replace the SU & Superuser.apk from the rootzipfile link at http://aosp.us/?p=294 before running it.
Click to expand...
Click to collapse
Will it work on Verizon RAZR M with JB Update.
I rooted, after being updated to JB, using the method posted DroidRzr.
just a test:laugh:
rooted, if not for stupid apps
Or, I think so anyway. I ran the exploit on my xt907 and can su from an adb shell, but superuser never asks me for perms when I try using root apps (which all fail, btw). Also replacing/updating the su binary from superuser doesn't work; it fails trying to get root access. So off to a root shell I go...
# cd /system/xbin
# cp su su2
# rm su
# touch su;ed su
: i
#!/system/bin/sh
export SHELL=/system/bin/sh
echo [email protected] >> /storage/sdcard0/su_args
script -qa /storage/sdcard0/su_script -c "/system/xbin/su2 [email protected]"
.
w
q
y
# #damn custom thing doesn't like wq
# chmod 755 su
Not the best logging, perhaps, but it does work. Well, almost. After checking the version of su a couple times, superuser opens a root shell and runs:
/system/bin/busybox touch /data/sutest && /system/bin/busybox echo YEAH
This is where it fails. Not only is there no YEAH, but no errors are printed, either. Some googling later, I found logcat--the results of that are here, and don't change if I replace su with su2. Google isn't being too much help concerning that crash. Anyone know what's up/how to fix? I find it really weird that I can get root from an adb shell, but not from apps.
Thanks.
Hi,
at first sorry for my english.
My Nexus 4 Stock ROM KK 4.4 KRT16O Rootet (SuperSU Pro, BusyBox Pro) changes its WiFi MAC-Adress after rebooting Device.
Is there any way to Fix this?
Sample MAC:
00:11:22:C5:F1:37
First 6 Numbers are always the same... last 6 changed
Wagi99 said:
Hi,
at first sorry for my english.
My Nexus 4 Stock ROM KK 4.4 KRT16O Rootet (SuperSU Pro, BusyBox Pro) changes its WiFi MAC-Adress after rebooting Device.
Is there any way to Fix this?
Sample MAC:
00:11:22:C5:F1:37
First 6 Numbers are always the same... last 6 changed
Click to expand...
Click to collapse
I've the same problem of you and i'm intrigued that nobody answered. Have you find a way to fix this ?
No fix found.
I have no solution found so far.
I am grateful for every tip
Wagi99 said:
No fix found.
I have no solution found so far.
I am grateful for every tip
Click to expand...
Click to collapse
Thanks !
Found this... Works Fix for Bluetooth and MAC adress:
HTML:
For mac address:
- In /persist directory create wifi directory. In the new directory create a file named .macaddr (don't miss the dot!)
Edit the file and put 12 random hex numbers in it (0-9, A-F), save.
- Set execute and read permissions for everybody on /persist/wifi directory and change owner of .macaddr to wifi:wifi and permission to 660 (read/write for owner and group and nothing else). In command line:
Code:
chown root:root /persist/wifi
chmod 755 /persist/wifi
chown wifi:wifi /persist/wifi/.macaddr
chmod 660 /persist/wifi/.macaddr
- run /system/bin/conn_init program. Can be run in root explorer(choose Linux Script Handler when you open it), or in adb shell:
Code:
su
/system/bin/conn_init
Then reboot and check if the changes got applied in settings
It took some doing, but after following the instructions in this link:
http://forum.xda-developers.com/showthread.php?t=2559915
I was finally able to root my Nook Glowlight. The instructions are kind of sprawled out and extremely unclear so I will sum up.
As always, you will need the ADB. In order to install the ADB, you need the Java Development Kit and the Android Studio (formerly known as the Android SDK)
http://www.oracle.com/technetwork/java/javase/downloads/index.html
http://developer.android.com/sdk/installing/studio.html
How to obtain root via ADB: The ONLY way you can root is using Windows. I was successful on Windows 7 32 bit, but it may be possible on other versions.
step 1) install bootloader driver.
You need to grab the drivers from here (bnusbdrivers.zip):
http://forum.xda-developers.com/showpost.php?p=49665945&postcount=279&nocache=1&z=184593200683593
then, open the Device Manager (on Windows). Be ready to right click on the new device 'omap3660' that shows.
With the nook turned completely off, plug in a USB cable. you will have less than 3 seconds to right click the new omap3660 device that shows up in the system profiler.
If you were successful and you right clicked on it in time, manually install the Barnes & Noble USB driver (there are entries added to the generic Google drivers for both the TI Omap 3660 bootloader and the ADB device after you modify the uRamdisk later on)
***NOTE***
If you WEREN'T successful on your first try (took me THREE times to get to it in time), you aren't going to get another chance to install the drivers. At least not easily anyway, because after Windows tries to automatically install the drivers for the bootloader and fails, it will disregard the device any time it shows up after that. So, you are going to need to delete the registry entries that it created, which in my experience was easier said than done. Even admin access was not sufficient to make the necessary changes to the registry.
You will need to launch regedit.exe using another tool called psexec which is available here:
http://technet.microsoft.com/en-us/sysinternals/bb897553.aspx
after you download the pstools package, copy those .exe files to C:\Windows\System32\ (in order to add them to $PATH in cmd.exe)
Then, once you've installed the pstools commands to C:\Windows\System32\, run cmd.exe as admin (right click it and select 'run as administrator') and then open regedit.exe with the following command
Code:
psexec -s -i -d regedit.exe
Then, once regedit is open you need to find the keys created by the Nook bootloader and delete them. The Nook bootloader's device ID is 0451:d00e
You are going to be looking in HKEY_LOCAL_MACHINE\Current Control Set\enum\usb\ for the keys with the bootloader's device IDs. There may also be keys generated in control set 001 and 002 as well. Delete all of those keys and then reboot your computer. Then with the nook power off completely, repeat the process from the first step. eventually you will be successful installing the bootloader driver.
Step 2) temporarily boot with uRamdisk-noogie
you need to download omaplink.exe from here:
http://www.temblast.com/android.htm
and you also need to download the four files which allow you to temporarily mount the boot partition; omap3_aboot.bin, u-boot-ng2-exp-v03.bin, uImage-ng2-130-stk and uRamdisk-noogie.
They are available here:
http://forum.xda-developers.com/showpost.php?p=49779966&postcount=285
download usbboot-ng2-images-noogie-v1.zip
The next part is easy.
Extract the .zip file and then fire up cmd.exe. cd into the directory of the newly extracted .zip
in the new working directory, enter the command
Code:
omaplink omap3_aboot.bin u-boot-ng2-exp-v03.bin uImage-ng2-130-stk uRamdisk-noogie
Then, with the Nook powered all the way off and omaplink running, plug it in and a few seconds later, after the device boots up all the way, you will be looking at the contents of the boot partition instead of the internal storage like normal.
Step 3) Edit uRamdisk
you will need to download bootutil.exe from here
http://www.temblast.com/android.htm
copy bootutil.exe to C:\Windows\System32
with the boot partition mounted, copy uRamdisk to your computer and extract the files init.rc and default.prop, eg;
Code:
bootutil /x /v uRamdisk init.rc default.prop
then using notepad++ (available here: http://notepad-plus-plus.org/) edit the files as follows
default.prop
ro.secure=0
ro.allow.mock.location=1
ro.debuggable=1
persist.service.adb.enable=1
and
init.rc
comment out lines 375 and 392-399
(do this by adding a # to the beginning of the line)
uncomment line 215
(do this by deleting the # at the beginning of the line)
save both files and then repack them into uRamdisk
Code:
bootutil /r /v uRamdisk init.rc default.prop
copy uRamdisk back onto the Nook, eject the disk and power off the device. Reboot and you should be able to connect to ADB via WiFi
eg;
Code:
adb connect 192.168.0.10
replacing '10' with whatever IP your Nook is grabbing from your router.
Step 4) Full Root
at this point, you have root access via ADB only. You will not have root access in any apps like Root Explorer, Terminal, TiBackup, etc.
In order to finish PROPERLY rooting your Nook, you need to install 'su' to /system/bin/ and install the superuser.apk
Code:
adb connect 192.168.0.10
adb shell mount -o remount, rw /system
adb push su /system/bin/
adb shell chmod 6755 /system/bin/su
adb install superuser.apk
reboot your device one more time and then you will be fully rooted.
*** Note ***
this devices firmware seems to be a strange hybrid between donut and eclair, although it purports itself to be Android 2.1. The Superuser.apk and su binary came from an old Cyanogenmod 4.6 build in case anyone was wondering (Android Donut). The ones from Cyanogenmod 5 (Android Eclair) do not work. you will get the 'install failed older sdk' error.
installing busybox
I tired installing busybox by using the stericson busybox pro.apk. It would always freeze at 6.47%.
I figured out that if I grabbed an older version of the busybox binary and pushed it to /system/xbin manually and then chmodded it to the proper permissions, auto updates and proper symlinking work using the busybox app
Code:
adb shell mount -o remount, rw /system
adb shell mkdir -p /system/xbin
adb push busybox /system/xbin
adb shell chmod 6755 /system/xbin/busybox
adb install busybox.apk
Then reboot, and run the busybox app to update and create symlinks.
enjoy!
installing nano and bash
Code:
adb connect 192.168.0.10
adb shell
mount -o remount, rw /system
adb push nano /system/xbin/
chmod 6755 /system/xbin/nano
adb push bash /system/xbin/
chmod 6755 /system/xbin/bash
bash
mv /system/bin/sh /system/bin/sh.bak
ln -s /system/xbin/bash /system/bin/sh
chmod 6755 /system/bin/sh
adb push profile /system/etc/
adb push terminfo /system/etc/
and then in terminal emulator under 'Preferences' change the initial command to
Code:
export TERMINFO=/system/etc/terminfo;export TERM=linux;export HOME=/sdcard;
and finally
Code:
adb push bashrc /sdcard
adb shell
mv /sdcard/bashrc /sdcard/.bashrc
exit
nano works just fine via ADB, but because of lack of 'ctrl' key (and physical buttons to assign it to) you won't be able to write files (ctrl+o) using the terminal on your nook. But between having full proper root access, busybox, a proper bash terminal emulator and nano for editing config files, this should REALLY extend the usefulness of your Nook Glowlight. It should work just fine on other versions of Nook too.
Hi N00b-un-2,
Many thanks for your summary!
There is one important edit that I think you missed,
in init.rc you also need to:
Line #375, comment out "disabled" with a # at the start of the line.
(see http://forum.xda-developers.com/showthread.php?p=49070213#post49070213)
without this I couldn't get adb to connect.
And since you already made it very noob friendly, might I suggested you clarify:
Line #215 remove # to enable adb over wifi
(rather than search for 5555)
Also, I'm not expert, but I believe the commands to get superuser on the device are (at least it worked for me):
adb connect 192.168.x.x
adb shell mount -o remount, rw /system
adb push su /system/bin/
adb shell chmod 6755 /system/bin/su
adb install superuser.apk
Finally, I'm not sure if this is important, but maybe remount system as read only again:
adb shell mount -o remount, ro /system
Thanks again, nice work!
---------- Post added at 01:48 PM ---------- Previous post was at 01:10 PM ----------
Hi again,
had similar issues with installing busybox, here's what worked for me (note needed to run su to create dir):
adb shell mount -o remount, rw /system
adb shell /system/bin/su
adb shell mkdir -p /system/xbin
adb push busybox /system/xbin
adb shell chmod 6755 /system/xbin/busybox
adb install busybox.apk
cheers.
As far as remounting /system as ro, I would HIGHLY recommend just rebooting at this point, otherwise your nook might be stuck in a weird pseudo-rooted state. Probably won't cause any problems, but why risk it?
Thanks for clarifying the line number. I will make the appropriate edits to my instructions. I was working off the top of my head and couldn't remember what exact line the ADB over TCP config was, as I just used ctrl+w '5555' to find it myself.
There are several pre-edited uRamdisk images floating around the forum with various features enabled which would be easier for noobs than extracting the config files and manually editing and then repacking them. In the future I'll probably throw those on here as well.
darz said:
Hi N00b-un-2,
Many thanks for your summary!
There is one important edit that I think you missed,
in init.rc you also need to:
Line #375, comment out "disabled" with a # at the start of the line.
(see http://forum.xda-developers.com/showthread.php?p=49070213#post49070213)
without this I couldn't get adb to connect.
And since you already made it very noob friendly, might I suggested you clarify:
Line #215 remove # to enable adb over wifi
(rather than search for 5555)
Also, I'm not expert, but I believe the commands to get superuser on the device are (at least it worked for me):
adb connect 192.168.x.x
adb shell mount -o remount, rw /system
adb push su /system/bin/
adb shell chmod 6755 /system/bin/su
adb install superuser.apk
Finally, I'm not sure if this is important, but maybe remount system as read only again:
adb shell mount -o remount, ro /system
Thanks again, nice work!
---------- Post added at 01:48 PM ---------- Previous post was at 01:10 PM ----------
Hi again,
had similar issues with installing busybox, here's what worked for me (note needed to run su to create dir):
adb shell mount -o remount, rw /system
adb shell /system/bin/su
adb shell mkdir -p /system/xbin
adb push busybox /system/xbin
adb shell chmod 6755 /system/xbin/busybox
adb install busybox.apk
cheers.
Click to expand...
Click to collapse
N00b-un-2 said:
There are several pre-edited uRamdisk images floating around the forum with various features enabled which would be easier for noobs than extracting the config files and manually editing and then repacking them. In the future I'll probably throw those on here as well.
Click to expand...
Click to collapse
Would have been good if I could have easily found a pre-edited image, but your instructions were a great alternative, thanks again
darz said:
Would have been good if I could have easily found a pre-edited image, but your instructions were a great alternative, thanks again
Click to expand...
Click to collapse
Sorry for the really noob question, I have rooted, wifi adb running and installed apps as per your instructions, but I can't seem to access any of it on the nook. How can I get access to the launcher I installed?
You mentioned pre-edited images, do any of those come with the apps I need to get access to a custom launcher?
Cheers,
Dariusz
==============
Updated: All sorted
==============
For some reason had some issues with ADW launcher, Launcher pro worked fine.
ps I think I made a mistake with the su step I suggested, if you run a one line shell command I don't think it keeps su privileges, so I believe you need to run commands within the shell as per below:
adb shell
mount -o remount, rw /system
/system/bin/su
mkdir -p /system/xbin
exit
adb push busybox /system/xbin
adb shell chmod 6755 /system/xbin/busybox
adb install busybox.apk
Noob
Hey guys any instructions noob friendly or a video in youtube,i stick up at dab connect 192.168.0.10.I dos't have a Windows PC and using Mac whit Parallels Desktop.Is it possible instructions for Mac?
The above instructions from N00b-un-2 should work fine running a vm with parallels on your Mac.
OB
Sent from my SPH-D710VMUB using Tapatalk 2
valentin1985 said:
Hey guys any instructions noob friendly or a video in youtube,i stick up at dab connect 192.168.0.10.I dos't have a Windows PC and using Mac whit Parallels Desktop.Is it possible instructions for Mac?
Click to expand...
Click to collapse
Before you perform the adb connect step you need to find out what your IP address is:
On your nook, click on the settings icon in the top right corner and then select "Change"
Under Wireless Networks, select the wifi name that you are already connected to (where it says "Connected to the internet")
This will display your connection details, remember that IP address
Now go back to your pc and type:
adb connect [IP address]
darz said:
Before you perform the adb connect step you need to find out what your IP address is:
On your nook, click on the settings icon in the top right corner and then select "Change"
Under Wireless Networks, select the wifi name that you are already connected to (where it says "Connected to the internet")
This will display your connection details, remember that IP address
Now go back to your pc and type:
adb connect [IP address]
Click to expand...
Click to collapse
BIG HINT! If you're using Powershell ISE, you have to type .\adb.exe connect [IP address] or else it won't recognize "adb" as an executable!
Don't ask why, because I don't know. :?
thenookieforlife3 said:
BIG HINT! If you're using Powershell ISE, you have to type .\adb.exe connect [IP address] or else it won't recognize "adb" as an executable!
Don't ask why, because I don't know. :?
Click to expand...
Click to collapse
So far so good,but now what?
valentin1985 said:
So far so good,but now what?
Click to expand...
Click to collapse
I just gave a little tip on Powershell ISE. I do not know much about the Nook GlowLight rooting process, as I have a NSTG, not a NG. Ask someone else.
thenookieforlife3 said:
I just gave a little tip on Powershell ISE. I do not know much about the Nook GlowLight rooting process, as I have a NSTG, not a NG. Ask someone else.
Click to expand...
Click to collapse
Yes,i try whit dis command .\adb.exe connect 192.168.0.9 but result is the same.
valentin1985 said:
Yes,i try whit dis command .\adb.exe connect 192.168.0.9 but result is the same.
Click to expand...
Click to collapse
But that's okay! What I said was, if you are using the command program Powershell ISE, do it that way instead. But you are just using cmd.exe, not Powershell ISE!
In cmd.exe, which is what you are using, it is not neccessary to type .\adb.exe. Just type adb.
From there, ask someone else in this thread.
thenookieforlife3 said:
But that's okay! What I said was, if you are using the command program Powershell ISE, do it that way instead. But you are just using cmd.exe, not Powershell ISE!
In cmd.exe, which is what you are using, it is not neccessary to type .\adb.exe. Just type adb.
From there, ask someone else in this thread.
Click to expand...
Click to collapse
I prefer to use ConEmu or Console2 when I am forced to use Windows. Not a big fan of CMD.EXE or Powershell/PowershellISE. there are plenty of other CLI alternatives out there
N00b-un-2 said:
I prefer to use ConEmu or Console2 when I am forced to use Windows. Not a big fan of CMD.EXE or Powershell/PowershellISE. there are plenty of other CLI alternatives out there
Click to expand...
Click to collapse
Well, as I ONLY use Windows and Powershell ISE has a nice-enough layout for my purposes, I use it. That's why I gave a tip on it.
Actually on a lot of installs just typing adb in the command console won't work either unless it's got the path variable set up correctly, I find it easiest to just right click and choose run as administrator, no need for the path to be setup.
OB
Sent from my SPH-D710VMUB using Tapatalk 2
FW 1.2.1
Hi guys,
thanks for creating this thread. I was wondering if this rooting procedure was tested with the firmware 1.2.1 ?
real-6 said:
Hi guys,
thanks for creating this thread. I was wondering if this rooting procedure was tested with the firmware 1.2.1 ?
Click to expand...
Click to collapse
This rooting procedure is for the new Nook GlowLight with firmware 1.3.1. Your device is a Nook Simple Touch with GlowLight, which can be rooted very easily using the rooting package here.