Hello people.
My screen was not working properly (for example I can't press X) so I bought a digitizer - I had this situation for almost a year, because it was only one certain parts of screen.
I mounted the digitizer today but the touch capability is completely off. When I was about to complain, I tried with the old digitizer, but the problem mantains!
Any idea what could be the problem? I already checked all the cables hundred times, and did a hard reset.
Related
Hi
I have a Qtek 9000 and recently I broked the display. As I had the service manual I thought I coud replace the display by myself. I bought a new LCD + touch screen on ebay and the replacing of the LCD was easy and went quite well. The lcd works fine but the touch screen don't. I cheked and clean all the contacts but couldn't make the touch screen work.
So I wrote de seller and we agree to send back de display and receive a new one that he will test bofore posting.
I placed this new display and the problem remais the same. The lcd works fine but the touch screen don't, so I think the problem could not be here.
I made a hard reset and even downgraded to the original ROM but the touch screen still not working.
Can anyone help me with this
Thanks
Have you tried the touchscreen side of things before re-asembling the casing?
I have had problems with the seal on the casing around the screen activating the touch screen permanently - so that it runs really slow (if at all) when using the keypad.
damn, did you get the touch screen to work at all?
which LCD + touch did you buy from ebay? hopefully we can avoid this seller and get something that works.
ever thought of buying the touch screen separately and putting that on?
Let us know how it goes.
whitemoo.
after disasembling/asembling device had the same ussie with touch,after a cup of hours using it.
armandoramos try to open,when UNI works,only a part of UNI with LCD(look page 21 in service manual-bottom picture,page 22 & page 23-middle picture),then try how works your touch.If it works-you just had pinch the LCD coaxial cable module.
i had a problem with my touch screen, i was lucky enough to find a second hand uni in a local market with a busted lcd but working TS.
i swopped over the TS and re-assembled my uni, one thing i did have to add was a tiny piece of foam between the ribbon cable assembly and the case, this was to push the two ribbon cable sections (TS and LCD) together, for a better connection, relying on the sticky bits alone was not enough.
hope this helps.
Touch screen unresponsive -> Inserted new LCD+digitizer -> touch screen unresponsive
My friend's Galaxy S4 i9505 had a crack in the glass and he asked me if I could fix it, so I carefully separated the glass from the LCD and glued a new glass on it using Loca UV glue. At first glance the result was absolutely great, but when I powerd on the phone again, the touchscreen suddenly was unresponsive. After re-checking al connections over again and resetting the phone back to factory defaults, the touchscreen was still unresponsive.
We decided to order a new LCD + digitizer unit from a Chinese Ebay seller with 99% positive feedback. After about a week and a half it arrived and I moved over parts on to the new screen and installed it very carefully. After checking all connectios and booting up the phone I unfortunatly noted that the touchscreen was still not functioning.
Now I really don't know what to do anymore, since the new LCD's touchscreen (digitizer) can actually be a D.O.A. what I would find bad coincedence or there is some sort of problem with the phone's mainboard wich would be bad luck.
What do you guys think? I am really not sure now. I will probably contact the seller of the LCD and try if I can return it and he will send me a new unit (No money back guarantee :crying: )
Maybe there are some other options left? Any ideas, please?
EDIT: Problem solved. Repairguy discovered that a small chip on the mainbord was damaged. He replaced the chip and now the phone works like a charm.
I had a similar problem after replacing my entire front assembly housing (preassembled glass, digitizer, LCD, frame). After I got everything transferred over from the old one (vibration motor, front camera, earpiece, headphone, motherboard, antenna micro-coax cable, lower bezel control ribbon), hooked everything up, screwed rear housing back on, reinserted SIM card & SD card, reattached back battery cover, powered it back on-- then to my horror, there was ZERO touch input response on the touchscreen. Panicking for a few minutes, started planning on moving everything back to an old Android (S3) phone, then thought to try a reset first-- I pressed the up volume & power buttons, got into recovery mode, then selected "wipe cache partition", then selected "reboot". After it restarted (and holding my breath), VOILA it worked! Touch input was restored, Hallelujah!
Just commenting here so I remember where this thread is.....lol
I'm going to be replacing the screen on my son's S4 when he's saved up enough money to buy the replacement screen......
Does anybody know if (in general) ebay purchased screens are reliable?......
http://i.imgur.com/rVnFwJM.jpg
I have a T-Mobile HD2. A few months ago, the digitizer got a little crack but touch was working fine, so I order a new digitizer and replaced it. No matter what I did, the touch wouldn't work with the new digitizer (I know about front buttons putting pressure on digitizer ribbon cable which sometimes results in touch not working).
I thought problem might be the LCD connection slot for digitizer, so I order a new LCD too. But even with new LCD and new digitizer still touch doesn't respond! What am I doing wrong?
This problem is still baffling me. Right now, I have 2 sets of digitizers and LCDs (old ones and new ones I purchased) and no matter what combination of them I use, digitizer is not responding.
I have to say the old digitizer used to work fine before I opened up this phone, it was just it had a little chip/crack in the edge so I wanted to replace it just to make it nicer. But now digitizer won't work at all!
Is there supposed to be an insulating layer between digitizer and LCD? What wrong did I do by opening up this phone? I was very careful. The only thing I am not putting back for now is the front keys and its flex cable. Other than that, all what I took apart before, I have put back!
Hello,
Since a few days, the touch input of my front (LCD) screen stopped working. Nothing looks damaged, the screen still displays what it is supposed to, but there is no reaction to my inputs (actions on volume and power buttons do work, as well as on the e-ink screen). Did this happen to any of you? Any suggestion on possible ways to fix it?
I should also mention that it still works by moments, like half a day working, then 2 days not responding, etc. I tried shaking it in different ways should a connector be slightly displaced, with no success: the few times it started working again came like a (good) surprise. I also had the great idea to do a factory reset, so now the phone is stuck on the Android configuration wizard, which must be done on the front screen (no possibility to use YotaMirror, apparently).
Thanks!
wicoz said:
Hello,
Since a few days, the touch input of my front (LCD) screen stopped working. Nothing looks damaged, the screen still displays what it is supposed to, but there is no reaction to my inputs (actions on volume and power buttons do work, as well as on the e-ink screen). Did this happen to any of you? Any suggestion on possible ways to fix it?
I should also mention that it still works by moments, like half a day working, then 2 days not responding, etc. I tried shaking it in different ways should a connector be slightly displaced, with no success: the few times it started working again came like a (good) surprise. I also had the great idea to do a factory reset, so now the phone is stuck on the Android configuration wizard, which must be done on the front screen (no possibility to use YotaMirror, apparently).
Thanks!
Click to expand...
Click to collapse
i recommend reflash it. possibly and more strongly recommend to flash the same version and region which was installed for example HongKong 4.4.3 baseband number .HK1.0.36a
ftp://fw.ydevices.com/YotaPhone2/Firmwares/
Actually, I forgot that the front screen was replaced several months ago (by a repairer that mistakenly changed the front screen instead of the e-ink one which was having an issue).
The factory reset didn't improve the situation, the front screen becoming "touch-insensitive" every few days. After checking how the screen connectors are supposed to be plugged (opposed to the screen), I noticed that gently tapping the phone front screen down helped to solve the issue each time it happened. A few days ago, I finally opened the phone (quite easy, there are two useful videos online) and unplugged/replugged the screen connector. It has been working fine since then.
If it happens to anybody (who would have its front screen replaced), I hope it can help!
So I bought a HD2 with bad touch screen. The issue was the very common one that every one knows, red button that was poking into the touch screen flex cable. I opened up the phone and fixed the issue and touch screen was working perfectly fine. In the process, unfortunately, I chipped a little edge of the front glass/digitizer. It was not a big deal as phone was still working fine. But I decided to buy a new front glass.
When my new front glass arrived, I separated the digitizer/front glass from LCD, but then half of my LCD got corrupted. So I ended up buying an LCD too!!!
Now comes the issue: when I put the phone together, touch screen doesn't work at all. I have tried all combinations of NEW / OLD digitizer and NEW / OLD lcd. Nothing works. I wonder if anyone can help me figure out why?
P.S. When testing, I happened to connect the phone to my 5w wall charger directly connecting it to power pins (without battery installed). Would that be why I lost touch? Is the touch issue now because of motherboard that was directly connected to adapter, not getting power from its designated battery?
have you tried the old lcd with old digitizer (which was working)?
tried it before replacing?
did you made some change to the software before replacing?
I currently have this problem too while trying to revive my old- almost 3 years inactive- HD2 with new touchscreen, and still trying to figure out where is the problem
b3rvirus said:
have you tried the old lcd with old digitizer (which was working)?
tried it before replacing?
did you made some change to the software before replacing?
I currently have this problem too while trying to revive my old- almost 3 years inactive- HD2 with new touchscreen, and still trying to figure out where is the problem
Click to expand...
Click to collapse
Yes I had tried the old LCD, and that didn't work either.
I installed a WiFi Keyboard on it.
Did you resolve this issue?