Related
Hi all,
I have decided to uninstall S2U2 and I don't want any other locking applications. However, is there is a way I can have the standard device lock activated with a short press of the power button?
Currently I am having to hold the 'End call' button until it locks, then turn the screen off with the power button.
Thanks
I have a pin setup and use the short press of the power button to put the phone into powersave 0 whixh then outs the phone into pin lock after a short while
If you push the hang off button for more than 10seconds, it will be locked
No...
FetchBLN said:
If you push the hang off button for more than 10seconds, it will be locked
Click to expand...
Click to collapse
I don't know about your device...
On my HD you can press the end button and count until 3, and the device is locked
I can't remember whether it's in HD Tweak or Advanced Config, but there's an option to automatically lock the keypad on screen turning off (both timed out or power button press I assume, but not tested) so you could try that?
Edit: instead of being lazy I actually looked it up - it's in HD Tweak, option 4.1; Lock -> AutoLock
Just tried it and it works, turn backlight off by short power press and it's locked a well as screen turning off!
Good tip: works for me!
By the way: you can configure what happens when you pres the "disconnect" button too.
Guys
Thanks for this thread. I am very confused when it comes to locking the phone. Can anyone tell me...
Does the built in device lock work well? Will it keep the phone locked when a call comes in ?
If so, then why do people use S2U2 or other third party apps? Also some people say that S2U2 drains the battery. Is this true? How does it drain the battery?
The HD tweak had the disadvantage that when the screen turns in 'shaded' state the device is also locked.
Then when unlocking the device the screen stays 'shaded'.
avimak said:
I don't know about your device...
On my HD you can press the end button and count until 3, and the device is locked
Click to expand...
Click to collapse
Maybe it takes you 10 seconds to count to 3.
I've finally got there with locking my HD... I had a S710 before the HD, and I liked the fact that on that I could hold down the "end call" button, and that it would lock the phone and turn the backlight off. The screen would then turn off completely after whatever time I had entered (2 mins I think). And on unlocking the device the backlight would turn on.
On my HD I have now disabled the device password, but enabled my PIN request, so that it secures the phone if it has been turned off completely. This means that I can now hold down the "end call" button for 3 seconds or so and it locks the device (requiring a 2-tap process to unlock, like the S710). I have also used the standard windows mobile settings (power) to have the backlight automatically turnoff after 30 seconds, and have used HD Tweak (setting 4.1) to autolock the device when the backlight turnsoff. The only problem is that when AutoLock happens using HDTweak, when I unlock it the backlight fails to turn back on, even once I have started using the screen. Any ideas on how to fix this?
Dave
chaosdefinesorder said:
I can't remember whether it's in HD Tweak or Advanced Config, but there's an option to automatically lock the keypad on screen turning off (both timed out or power button press I assume, but not tested) so you could try that?
Edit: instead of being lazy I actually looked it up - it's in HD Tweak, option 4.1; Lock -> AutoLock
Just tried it and it works, turn backlight off by short power press and it's locked a well as screen turning off!
Click to expand...
Click to collapse
Just to confirm my above question regarding this specific feature of HD Tweak... I have got this working on my HD now too, but when it autolocks, and I unlock it, the backlight doesn't turn back on, and the only way to make it turn back on is to hardbutton off and on the device (not power-off, just press the button the top of the phone and press it again).
This is stopping me from using the HD Tweak autolock now, which is annoying because it does precisely what I need! Can anyone offer any advice?
I've just realised that it actually says within HD Tweak itself (on 4.1 option selector) that this is a known issue... any idea on if and when it will get fixed?
How about using Gyrator to lock the device? I have set it to lock the device and switch off the screen on inserting the stylus. Also, I have it set to unlock and switch the PDA on when the stylus in removed.
Simple. Works for me, anyway!
james00000007 said:
I have a pin setup and use the short press of the power button to put the phone into powersave 0 whixh then outs the phone into pin lock after a short while
Click to expand...
Click to collapse
Hi,
Is this similar to an application my friend had on his iphone. Basically, when he needs to use the phone, he needs to put in a pin to unlock. I think the Nokia E61 has a similar feature.
nikki-m said:
How about using Gyrator to lock the device? I have set it to lock the device and switch off the screen on inserting the stylus. Also, I have it set to unlock and switch the PDA on when the stylus in removed.
Simple. Works for me, anyway!
Click to expand...
Click to collapse
Can u let us know how to u set it?
nikki-m said:
How about using Gyrator to lock the device? I have set it to lock the device and switch off the screen on inserting the stylus. Also, I have it set to unlock and switch the PDA on when the stylus in removed.
Simple. Works for me, anyway!
Click to expand...
Click to collapse
i hav a qns, at the locked screen, when u rotate ur device, does the screen rotate as well???
i had tis problem whn using gyrator to lock, whn its lock at home screen, the screen wil rotate if i rotate my device. how to disable that???
davehodgkinson said:
Just to confirm my above question regarding this specific feature of HD Tweak... I have got this working on my HD now too, but when it autolocks, and I unlock it, the backlight doesn't turn back on, and the only way to make it turn back on is to hardbutton off and on the device (not power-off, just press the button the top of the phone and press it again).
This is stopping me from using the HD Tweak autolock now, which is annoying because it does precisely what I need! Can anyone offer any advice?
I've just realised that it actually says within HD Tweak itself (on 4.1 option selector) that this is a known issue... any idea on if and when it will get fixed?
Click to expand...
Click to collapse
Mhh, I also think it's very annoying. I first used the auto lock feature by setting
HKey_CURRENT_USER/ControlPanel/BackLight/AutoDeviceLockEnable = 1, but I also have the backlight-issue, which is really annoying.
I also installed S2U2, but after installing that program the battery-life was inacceptable. By now I'm using the manual method, pressing hang-up for 3 seconds. It works, but I often forget it, and it then happens easily that I press the hard-button which awakes the phone from standby and I make pocket-calls.
The auto-lock feature is also exactly the thing I need, except the fact that I get the backlight issue then. Does anybody know how to fix the backlight issue? Maybe by editing another key in the registry?
Regards,
Tobi
As I said in the hint topic, in order to lock my device I just press the power off button (this activate the stand by), simple and fast
I use S2U2 at first, but it drains power too much, so I uninstall it after 2 days.
Then I use your method - hold the end call button to lock the device.
Now, I change the right softkey to invoke a small application that will turn off the machine (just like press power button). When I take out the stylus, the machine will on again.
Thus, I don't need to press any button, and I feel it is better......personally.......
stm2008 said:
I use S2U2 at first, but it drains power too much, so I uninstall it after 2 days.
Then I use your method - hold the end call button to lock the device.
Now, I change the right softkey to invoke a small application that will turn off the machine (just like press power button). When I take out the stylus, the machine will on again.
Thus, I don't need to press any button, and I feel it is better......personally.......
Click to expand...
Click to collapse
which application are you using now to turn off the screen? sounds interesting.
Tyrion84 said:
As I said in the hint topic, in order to lock my device I just press the power off button (this activate the stand by), simple and fast
Click to expand...
Click to collapse
Yes, but when I activate standby and put the phone into my pocket, I often accidently hit the button again, which reactivates the phone. hit_one_button_to_unlock ist not tobi-proof
Hi there,
How can i get the lock screen by just pressing the power button? For example, I'm using the mobile and then i press the power button to turn off the light of the screen, and then when i press the power button again to turn it on, the lock screen appears, like iphone. I couldn't find it on the windows configuration.
Thanks
There is alot of applications which can do this, but most of it has serious bugs and issues.
Hope that someone is able to firm this issue out ASAP.
But, for now, no solution is available.
The lock screen that i'm talking about is the one of the Windows Mobile 6.5 not the ones that we get from programs of internet. The new lock screen of wmb 6.5
the lookscreen is activated by end key, may be you can remap it to the power key, but then how are you go to turn off the device?
Hi, Im using the Smartlock (v1.7c) and it works fine form me. Just use the suspend lock option (I only use that one). Then every time u turn the screen on it will be locked with the wm6.5 lock screen.
http://forum.xda-developers.com/showthread.php?t=505032
harfuch said:
Hi, Im using the Smartlock (v1.7c) and it works fine form me. Just use the suspend lock option (I only use that one). Then every time u turn the screen on it will be locked with the wm6.5 lock screen.
http://forum.xda-developers.com/showthread.php?t=505032
Click to expand...
Click to collapse
WOW
That's the one, thanks!!
Does anyone have a small example how this has been developed? I guess with a notification and a keypress?
Much appriciated
After i hang up on a call (when the phone is in sleep mode and the screen is locked) the screen unlocks. this is quite contrary to what is mentioned in the phone manual chapter 1 page 45. this becomes an issue since i use a bluetooth headset and the phone remains in its sleeve/case and after every call, a whole bunch of applications will launch since the case is in contact with the screen. have i overlooked some settings or are there other owners who have faced this issue?
ideas and suggestions welcomed
did you check it out if any of the hardware buttons being pressed against the case hence wakening up the phone.?
i had it to only closed al my apps in taskm and it stoped flickering
My HD2 is also behaving in the same way even in controlled test conditions - the phone unlocks when a call comes in (I'm presented with slide to accept or reject call) The phone unlocks during the call, but fails to lock again on disconnect (either by pressing "end call" or hang up via bluetooth).
Can anyone verify this? Is it interacting with something I installed?
I believe I found a (complicated) workaround.
What I want: leave HD2 inside pocket, answer calls with bluetooth headset, hang up and phone will go back to lock.
Problem: After I hang up using bluetooth or press the big red "End Call" button or the other party hangs up, the phone stays unlocked! It stays powered on and all kinds of buttons gets clicked.
Practically all lock sw uses their own lock screen (which I don't want to install). CSDevCtrl does not trigger by phone. TouchLockPro uses its own transparent lock screen but can respond to phone events. Using the !SUSPEND for TAPI\Ended under settings does not seem to work when the screen dims about 50 secs into the call.
Solution: Use TouchLockPro together with LockAndOff. Get TAPI\Ended to run LockAndOff will turn phone off, whether by bluetooth, big red "End Call" button, or the other party hangs up.
BTW: I think there is some confusion on whether the phone locks when you
1. press the big red "End Call" button, or
2. the hard "End call" button
in the forums.
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
linivan said:
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
Click to expand...
Click to collapse
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
johncmolyneux said:
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
Click to expand...
Click to collapse
My proximity sensor does not work, when I am getting a call my screen turn off and when I am taking the phone out from my face it turn on only when I am out side at the sun!! the screen stay off when I am inside room. I tested it with flsh light and it is working also.
I have a T-Mobile US version of the HD2. I am having the same problem when using the bluetooth system in my car. After answering or making a call the phone stay unlocked. And then starts making random calls while I am driving!!!!
There has got to be an easy fix for this!!!
Buy pocketshield, problem solved.
i have this unlock problem with 1.48 rom and i solve it by pressing start button and lock. after that everything works fine unless i change theme in settings. then just repeat first step.
Solved
Same trouble with me until I use the following software. I tried it and it's almost perfect. unzip it and just copy to your HD2, run CallerLoc.exe and click Yes, you'll find:when you hang up, or he/she hang up a call, or a call is established, the screen will turn off.
Why say 'almost perfect', the software is in chinese, but the filename is in english. and it's a call location software but with the function we need.
To stop or before you delete the software, run Callerloc.exe and click Yes again.
Hope this will help you. Sorry I don't find a English version of this software. I esure and I'm using this software perfectlly with my Leo.
theciscokid said:
Buy pocketshield, problem solved.
Click to expand...
Click to collapse
Same for me
Greetings.
I understand this is quite an old thread I'm digging up but I need a little help as well and I didn't want to start a new topic just for that.
I've this silly problem, appeared right out of the blue:
You all know the standard manila behavior, when the phone is idle, the screen first dims and after some more time, depending on your preferences, the screen locks. It also locks if you press the power off button. This all was happening to me till this morning.
I added an event in the calendar (the only change I made today) and after that, my phone dims and then goes in sleep mode after the designated period of time, but DOESN'T lock!!! It doesn't even lock when I press the power off button. I can still lock it by pressing Start and then lock or by press and hold the power button and choose the lock phone option. So one would say that it's still operational, so why bother about it, but I kinda liked the standard function and I have to freaking idea why it changed!!!
I'd be most appreciative if you could offer some help with that.
Oh, I forgot to mention. Soft reset didn't solve the problem. Erasing the calendar event didn't either.
My phone runs the factory ROM (1.66.482.1 ELL), I haven't changed anything other than user settings (yeah, I'm a noob... )
Thanks in advance!
Nasos
Pocketshield could be the end of your problems. You can try it for 10 days and see how it goes...
But why do I need to buy third party software in order to revert my phone to it's original operation?
No, this is not the answer I am looking for. I was wondering if you know of any kind of settings that might have changed by accident and caused this undesired behavior.
Thanks.
The best to return to normal operation would be a hard reset. Or you can spend a while trying.
You can try
HKLM\Software\Microsoft\Shell\Lockscreen\Enable=1
HKLM\Software\Microsoft\Shell\Lockscreen\Active=1
Thank you very much. I opted for the hard reset option... I hope it stays ok this time!
My HD2 also had some strange unlocking and unwanted calling.
I noticed it appeared when using the android style lockscreen.
When I changed back to the original one, problem solved
i had this too. the andriod lockscreen seems to be a bit buggy last time i used it, i accidentially called 7 random numbers
After I have opened the camera app with double click I am not sure what I click on as I am trying to handle to phone to take picture a blue line appears scanning the phone which starts form top to bottom and then bottom to top and the phone becomes totally unresponsive. You cant unlock the phone and you cant take any incoming calls etc.
Not sure what happens after 30 minutes or so when you double click the phone then it goes back into the camera app and after you take a photo it works. If you don't take a photo and click back button the blue line starts scanning again and phone will become unresponsive.
Ntt sure what this is.
Phone SM-G9287.
I found what is happening.I have lock pattern setup to unlock teh device.Now when i double tap the home button it goes into camera app and then suddenly the blue line appears whcih moves top to button and bottom to top as if it is scanning.The phone will become unresponsive as i mentioned above i.e touch screen wont work but u can still take photos using up and down volume button but not by touching on the screen.
To overcome this you have to press back button and then press the hoem key 3 times and the touch scren becomes active again and hence now if you draw the lock pattern the phone will recognize it and unlock the device and it works normally.
Not sure this is a bug or not but very confusing.Can anyone try teh same if you ahve SM-G9287 phone and confirm if you are also seeing the same.
phone freezes up when utilizing camera, Touchscreen becomes unresponsive.
I experiance the same but My phone is loked whith fingerprint sensor.
My 10 day old phone freezes up when utilizing camera (activatd with double touch of home button. Touchscreen becomes unresponsive.
Nothing can be done to get it working.
Tried every hardware button, which seem to work as designed.
the solution Vravik mentions does not work with me.
Only working option i can manage to do software reboot the phone with power button combined whith volume down key.
but after booting the screen is still unresponsive. see:
https://www.youtube.com/watch?v=Q-hbOHAuFhE
I was advised to do a factory reset and just after starting up the phone again and register myself the screen froze up again.
Does any one have a clue on this
I have noticed this issue as well
I have noticed this issue as well. But after doing a full reset and latest software update, I didn't notice this
vravik said:
After I have opened the camera app with double click I am not sure what I click on as I am trying to handle to phone to take picture a blue line appears scanning the phone which starts form top to bottom and then bottom to top and the phone becomes totally unresponsive. You cant unlock the phone and you cant take any incoming calls etc.
Not sure what happens after 30 minutes or so when you double click the phone then it goes back into the camera app and after you take a photo it works. If you don't take a photo and click back button the blue line starts scanning again and phone will become unresponsive.
Ntt sure what this is.
Phone SM-G9287.
Click to expand...
Click to collapse
Hi there,
I dont really know when it started, but when I am trying to quick access the camera via tapping the powerbutton twice while the phone is locked, the camera app pops up but the screen stays black. Hitting the HomeButton and the powerbutton twice again lets the camera app pop up again, this time showing a picture.
Sometimes it even works like it should on the first time, but most of the time it doesnt. Anyone else having this behavior?
Any recommendations? Running entirely on current stock firmware.
Thank you and best regards,
joha
joha386 said:
Hi there,
I dont really know when it started, but when I am trying to quick access the camera via tapping the powerbutton twice while the phone is locked, the camera app pops up but the screen stays black. Hitting the HomeButton and the powerbutton twice again lets the camera app pop up again, this time showing a picture.
Sometimes it even works like it should on the first time, but most of the time it doesnt. Anyone else having this behavior?
Any recommendations? Running entirely on current stock firmware.
Thank you and best regards,
joha
Click to expand...
Click to collapse
I've had this happen once maybe twice, the camera doesn't seem to wake just the app so you have the app showing but no image from the camera. Screen lock is set tell use pin on my phone. I'd guess it's a bug.
Could try turning the lock screen off see if it still happens.
I can confirm this behavior. But I cannot reproduce it systematically. Sometimes it works sometime not.