Related
Was trying to install wp7 on my hd2, but now im stucked on magldr version 1.13. Forgot that the volume buttons doesnt work and i cant get the phone out of there. Try to load original rom or even task 29 but nothing becuase the pc doesnt recognize it. When the phone its booting it says something like cant boot from sd android kernel fail and then the menu and i can select only the first 1 boot wph.
Is there a way to get the phone out of there, or my only hope its to repair the volume button.
thanks
If you haven't been able to flash anything then as long as you just reboot your phone you'll just go back to whatever ROM you had previously
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
i remove the battery but when the hd2 start again it boots instantly to magldr, i need another way to flash it different to the three color screen (i cant get there becuase the volume down button its broke).
i have a problem like that
If your volume keys don't work, then there is seriously, no other way. You can't get into bootloader mode without the volume keys, and the you can't flash a different rom without the volume keys, so yeah, your device is pretty much bricked....
But IF the vol. down key works, I assume that it is something with MAGLDR or HSPL, or possibly an error in RAM. Are there anything that can be flashed via magldr that checks the state of underlying HSPL?
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Maybe I'm tired or too old... but I don't understand your questions
You can imagine the different "softs" as layers:
1st: HSPL (or SPL) - it's the one you enter by pressing vol-down while booting.
this one give you the ability to flah a WM ROM (original or custom), a radio or MAGLDR
So if vol-down if dead... your phone also
nb: the first splash screen is at this level, so it will be still here after flash of MAGDR, CWM, NAND, WM7...
2nd: MAGLDR - it's the one you go in by pressing "end call" while booting.
It gives the ability to flash a NAND or WM7 via DFT
So if "end call" is dead... you're not But it's anoying I think...
3rd: CWM - it's the one you go in by selecting "AD recovery" in MAGLDR
It gives you the ability to flash a "CWM NAND" or an update... It also gives the ability to backup/restore a NAND.
So please clarify your question if you need help. More important do not post different problem by saying "same here". It's just confusing. Even if you can't boot your NAND it's not always the same problem
Let's try again dudes
osugsxr said:
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Click to expand...
Click to collapse
HTC after sales... or few bucks
That is what I'm thinking, will try warranty to see if that works if not not ill see what they charge. For now back to the nexus s.
truc007 said:
HTC after sales... or few bucks
Click to expand...
Click to collapse
Sent from my Nexus S using XDA App
This is the answer to your problem if it does work find someone that is not a noob and have them fix your phone its really not that hard
Ok guys please help me I don't wanna start new thread
I installed on my hd2:
-HSPL 2.08
-Radio 2.15.50.14
-Magldr 1.13
-CMR
First of all I noticed that I dont have to hold the power button to get into the magldr menu.
I couldn't get into Boot As SD so I wanted to flash custom rom from bootloader. Unfortunately I can't do that. Even tried HR. Is there any solution to flash stock ROM
Any help would be greatly appreciated
Stuck for me too
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
hi, have u tryed with the small button under the volume down button? it works as the volume down button...
If u can go in bootloader (if ur volume down works) could be ur nand is corrupted (as mine ) so bye bye hd2... i m waiting for the htc sensation
DAF doesnt' work
ChitownWingMan said:
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
I figured out the Android problem (I needed a different rootfs).
I have magldr 1.13 working!!!!
However, when I try to run DAF I get the same:
"An error has occurred
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (725)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (304)"
error that I have seen all over XDA-Dev.
However, none of the fixes I have seen on here have worked. I am running Windows 7 Professional.
I have tried:
Disabling Use USB in the Window Mobile Device Center
I have tried ANDR_INSTALL
I have rebooted
I have tried deleting all of the unattached USB device in the device manager.
I have tried using LeoAdvancedRUU
I have tried starting DAF first and then connecting the usb cable
I have tried connecting the USB cable first and then the starting DAF.
Help please!!! I was up until 8:30 AM trying to get this to work (I started at about 10:00 PM).
i also put the hd2 into the freezer for 10 minutes to solve heat problem and it doesn't start bootloaderi...
the nand corrupted..it start magdle but don't start android or cwm..there is nothing to do
tser04 said:
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
Click to expand...
Click to collapse
I have the same exact problem !! WP7 is the only OS that works and I want android
also the volume down key works...should I try to reflash HSPL ?? will that work ?? since HSPL 2.08 is already installed !??
Happen error
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (291)
hi,
MAGLDR doesn't recognize my sd card . i can't use usb mass storage , AD SD => CWM . apparently all the roms i want are released az ZIPs ...
is there a fix for that ?
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
waspsl said:
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
Click to expand...
Click to collapse
Yes exactly thats what i m doing. But it passes to magldr. I even have reset from the red button at the back but no way to bootloader
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
MTN_HD2 said:
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
Click to expand...
Click to collapse
Yes, install the appropriate cwm partition by going to usb flasher and running daf.exe. Then the phone will reboot to magldr, select AD recovery and you can then flash zip roms or updates, backup etc etc etc.... I have a 512 device also, so no problems.
I guess one of the reasons for running recovery off NAND is that not all users could get the sd based recovery to work.
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
fastscorpion2010 said:
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
Click to expand...
Click to collapse
What hspl version and radio are you using? To use magldr you need 2.08.hspl and radio 2.08.50.xx or higher .50 radio
I'm not sure why it would hang on reflash to winmo, but let's try get to Android.
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
grisantycosme said:
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
Click to expand...
Click to collapse
you're using Stock SPL, you need Hard SPL (HSPL)
ClydeB1 said:
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
Click to expand...
Click to collapse
You...so...rock!
I've been getting utterly frustrated with watching Windows bars filling only halfway, but your solution worked like a charm!
:good: x many!
magldr problem
hi
i was instaling the magldr on my htc hd2, but during the instalation i realise that my VOLUME UP and DOWN buttons are broken and dont work...i have to choose some option in MAGLDR but i cant...so i'm stuck here, my phone boots only MAGLDR even when i restart the phone from the red button, or even when i pull out the batery...is there some option to turn off the magldr, without using the volume buttons? please help me..in the store workers tell me that they cant fix the broken volume buttons...and now i cant use my phone... cheers...
Hi
I have a few question about MAGLDR (i dind't find the answer on xda and google or the answers were not clear for me).
Actually when i want to install an Android ROM i used only the ROM which can be installed with an Android directory + haret.exe + ...
I would like to go to MAGLDR because there are more ROMs available but i have questions.
I know that there is 2 modes with MAGLDR: NAND or SD
Sorry in advance for maybe the stupid questions :
1/ Is the "Boot AD SD" mode equivalent to an install with an Android directory + Haret.exe + .... (=First way to install Android on Leo device found a long time ago) ?
2/ Is the "Boot AD SD" mode of MAGLDR doesn't touch to Winmo ROM: we still boot on WinMo and after go to Android?
3/ Do we need to reinstall fully the WinMo version after installing an SD Android version with MAGLDR?
4/ Is it possible after poweron to choose between Winmo and SD Android installed with MAGLDR?
Regards
Well, well, well...
U have that all wrong m8. U r just lost in all of that.
MAGLDR is only one of the tools used for flashing there r some more..
Basically u have two options how to flash your Android.
1st DFT mode - u need to have MAGLDR installed
2nd CWR(ClockWorkMode Recovery) mode - u need to have MAGLDR + CWR
Well I think u should stay with the 1st option cos u new to this and u can find it easier than CWR
So go here **HD2 Android NAND Development - Sticky Roll-Up Thread**
And here [GUIDE] Flashing Your First HD2 NAND Android Rom [For Newbs]
U will find all what u need there
fana75 said:
Hi
I have a few question about MAGLDR (i dind't find the answer on xda and google or the answers were not clear for me).
Actually when i want to install an Android ROM i used only the ROM which can be installed with an Android directory + haret.exe + ...
I would like to go to MAGLDR because there are more ROMs available but i have questions.
I know that there is 2 modes with MAGLDR: NAND or SD
Sorry in advance for maybe the stupid questions :
1/ Is the "Boot AD SD" mode equivalent to an install with an Android directory + Haret.exe + .... (=First way to install Android on Leo device found a long time ago) ?
No is not.This is something different
2/ Is the "Boot AD SD" mode of MAGLDR doesn't touch to Winmo ROM: we still boot on WinMo and after go to Android?
If u flash your android ROM than your WM is gone and if u want it back than u have to reflash it again
3/ Do we need to reinstall fully the WinMo version after installing an SD Android version with MAGLDR?
Yes, u have to
4/ Is it possible after poweron to choose between Winmo and SD Android installed with MAGLDR?
Regards
Click to expand...
Click to collapse
houpsss
thank for your first answer rikardo1979...
MAGLDR will replace the Hardspl i have?
There are still something that i don't understand;
Why using MAGLDR in "Boot AD SD" it erases the WinMo ROM?
In this mode the Androir Rom is not only in the SD card?
Regards
No MAGLDR will not replace the HARDSPL.MAGLDR is just the software whats loaded to the phone and is used to flash, update,..etc
About the Boot AD SD- this option is used only if u want to boot from MAGLDR into CWR whats another software whats u using to flash the ROM from SD card.
In MAGLDR is also an option "USB Flasher " what u using if u want to flash ROM using DFT method whats similar to flashing the WM ROM's. So u connect the phone with USB to the PC than u boot into MAGLDR and u choose USB Flasher. Than phone will wait for connection with PC. After u just run the DAF.exe from the ROM of your choice what u downloaded and the flash procedure starts.
Its similar to the WM flashing.
In CWR flashing u copy the ROM into your SD card and u flash it from there with no need of PC.
If u flash the Android ROM into the phone by DFT or CWR mode either of these erase the WM ROM
Also if u use NAND ROM its mean the whole ROM is flashed into the internal memory of the phone where the others use SD card to store the data on it to save the internal memory.
And u can also express your gratitude just by simple click on the Thanks button on the bottom of my posts.
fana75 said:
thank for your first answer rikardo1979...
MAGLDR will replace the Hardspl i have?
There are still something that i don't understand;
Why using MAGLDR in "Boot AD SD" it erases the WinMo ROM?
In this mode the Androir Rom is not only in the SD card?
Regards
Click to expand...
Click to collapse
I don't know where u from but if u not confident to do it u still can try find some1 from the same place and meet him so he can show u how to
im having htc hd2 with winodws 6.5 , i used to install different different andriod version, but wat i hav problamatic like when i have to change my andriod nand to other one then i hav to insatll original windows 6.5 image first and then MAGDLR loader and then install the disered stuff , also MAGDLR not installing from andriod so its realy very long proccess for me to do this. is there any way to enter MAGDLR boot menu so i can flash my phone again
trilok31 said:
im having htc hd2 with winodws 6.5 , i used to install different different andriod version, but wat i hav problamatic like when i have to change my andriod nand to other one then i hav to insatll original windows 6.5 image first and then MAGDLR loader and then install the disered stuff , also MAGDLR not installing from andriod so its realy very long proccess for me to do this. is there any way to enter MAGDLR boot menu so i can flash my phone again
Click to expand...
Click to collapse
Hi,
If you re-installed an original WM ROM,you will have lost everything on your phone:
HSPL,MAGLDR, RADIO,etc.
You must start again.
Everything you need to do is listed in my sig...guide number 2.
trilok31 said:
im having htc hd2 with winodws 6.5 , i used to install different different andriod version, but wat i hav problamatic like when i have to change my andriod nand to other one then i hav to insatll original windows 6.5 image first and then MAGDLR loader and then install the disered stuff , also MAGDLR not installing from andriod so its realy very long proccess for me to do this. is there any way to enter MAGDLR boot menu so i can flash my phone again
Click to expand...
Click to collapse
Im not sure if you are saying that you cant enter the Magldr Menu when you boot up your phone or that you are going about installing Android incorrectly.
To get Magldr on your phone you start with Windows Mobile, then flash the latest 2.**.50.** Radio and then flash Magldr v1.13. When the phone restarts you can enter Magldr by long pressing the power button and then either install NAND Android OR install Clockwork Mod via Magldr which is the far better way to go.
With Clockwork Mod on your phone you can backup and restore Android Roms, flash and update Android Roms via a zip file copied to your storage card, clear caches and setup the A2SD partition on your storage card.
There is never any need to reflash Windows Mobile between Roms.
Take a look at the 2 Android flashing guides in my sig (especially the Clockwork Mod guide) which should help you alot with what you need to do.
Mark.
i have a hd2 thats booting directly to the sd, i hate it, its slow, it lags and im tried of it...
i want to do a nand install b/c ive seen them perform 10x better.
how can i do the nand install?
if i take the sd card out the phone just sits at amagldr v1.13 screen. i press the volume button down and it doesnt move... someone help me please
try this
http://forum.xda-developers.com/showthread.php?t=893948
not helping b/c for some reason i cant scroll with the volume buttons
if you leave the sd card in can you scroll up and down.dont you have to flash hspl 2.08 first to be able to have nand.im just asking these questions cause i dont know much about the dual booting,but i know a good amount about the nand type daf and cwm.
trmixing said:
i have a hd2 thats booting directly to the sd, i hate it, its slow, it lags and im tried of it...
i want to do a nand install b/c ive seen them perform 10x better.
how can i do the nand install?
if i take the sd card out the phone just sits at amagldr v1.13 screen. i press the volume button down and it doesnt move... someone help me please
Click to expand...
Click to collapse
To install Android to nand using MAGLDR 1.13 you have two choices to do this. You can do it the original way with a ROM that flashes via option #5 USB Flasher and a DAF installer utility. Or you can flash Clockwork Mod Recovery via option#5 USB Flasher and then booting ifnto CWM via option#8 AD Recovery. then using install zip from sdcard. You have to have a MAGLDR compatible ROM though, which is most ROM now anyway.
But as you can see you have to be abale to scroll with your volume up and down buttons to do any of this, so I really don't know what to tell you. I will wait for your next post before giving any further suggestions.