Database Users

DIY scratch protection

I noticed the first scratch on the corner of my Jam today. Since electronics always take the most abuse on the corners, I devised a quick and easy way to protect the corners of my Jam while I'm in Europe for the next 3 weeks. Take electrical tape or clear satin tape and place a piece over the corners. Works best if you cut a slit in the tape so you can fold it around the corner without wrinkles. In all probability the device will land on its corners if dropped or take the most abuse on the corners if scraped against something. Thus, problem solved; I did it to my digital camera too. It doesn't look half bad on either device, and if you can't stand the black corners, just use clear tape. Any tape works as long as the adhesive won't stick to the advice after you remove the tape.

damn that's dead sexy :lol:

Damn! Why didn't I think of that????
Why don't you run the tape all the way round? I think it will look somewhat better!... :wink:

I'm sorry, but that has to be the stupidest looking thing I've seen in a long time. Why don't you just get a silicon case for about $10 off of EBAY? I mean, if you REALLY need electrical tape and that's all you can find...great. But just get a cheap latex or silicon case such as the ones from JavoEdge.com.
Do you put electrical tape on the front and rear bumper of your car too?

GHETTOOOOOOO

Just curious, what specifically do you expect to happen in Europe over the next three weeks that would necessitate such a precaution when you don't prepare against similar risks at home :wink: ?

hehehehe... Good point JPreston!!! :lol:

I don't get it! People seem to get very upset when they discover they scratched the ball mirror on the back of their JAM. Now we have a JAM covered in electrical tape. Should we all carry our devices in the original box? Or better yet never use them to keep them in pristine condition? I am not saying I didn't get a little ticked off when I found a nice big scratch in the corner after a small drop but come on! I think we're all getting a bit too precious. Anyway, to each their own.
Of far more concern is the gunk that gets on the screen from my face every time I hold the JAM to my head! I mean yuck! What the heck is up with that? Is there that much oil on my face??? I just washed it! I gave my phone to my friend the other day to make a call and his face left some sort of super oil on the screen that wouldn't scrub off for several minutes! Its gross and embarassing! I think we need some sort of face oil protector!

Does anybody have any idea for cheap screen protection? I think the prices are outrageous for the slices of film sold as protectors.

I use the cheapest of them all...
They are made for Palm devices and are sold on flea markets or "One Dollar" stores... :lol:
They cost $1 dollar the 12 Pack!
Just cut them to size and go!

scratch? i've droped my mini 2 times and got 3 dent edges. damn sad. The stupid casing they gave me is getting pretty loose. I put it on my belt.... so everytime i knock it seems that pouch just flings out. The screw and the plastic seems to have worn off.
I think i'm gonna go to a skinning shop to hide the dent edges.

try to buy a leather case for Nokia 7610. it fits.
You dont use that in the box lether case. It will easily fall of that tiny hook.
Wit the lether case of Nokia, it is mounted sideway into the belt by a leather that is sewed.
mine has never fallen. Even if it falls off the belt when you undress, the leather case is so stiff that it will not dent the mini.

@Emil...
Can you post a picture of your JAM in the Nokia case for us to see?

vmirage said:
scratch? i've droped my mini 2 times and got 3 dent edges. damn sad. The stupid casing they gave me is getting pretty loose. I put it on my belt.... so everytime i knock it seems that pouch just flings out. The screw and the plastic seems to have worn off.
I think i'm gonna go to a skinning shop to hide the dent edges.
Click to expand...
Click to collapse
Dropped mine on a concrete floor from about 1.5 meters and got a really ugly dent on one of the corners of the battery cover. The cover wouldn't even go back on!
Easy fixed though. Just took a plastic pen and pushed the dent out from the inside. It still shows a slight dent and small scratches if you look closely, but what the heck...

Anyone know of any metallic paint (model, SKU, UPC code) that I could use on my JAM? I rarely put on my seatbelt, and the one time that I decide to play safe, I scratch up the corner of my JAM. I'd never go "ghetto" as one person put it in the thread, but I'm sure there's something out there to match it up. Any ideas?

Get the jam off of your belt and put it in a proper car holder and you will not only protect it from getting scratches from your seatbelt, you will also get it charged while driving. And also one less reason not to wear a seatbelt that could save your life in the case of an accident.

Incidentally, can anyone recommend a decent car kit for the JAM? I want one I can mount with some amount of ease somewhere on the console... I don't like those ones that stick on the windscreen.

elyl said:
Incidentally, can anyone recommend a decent car kit for the JAM? I want one I can mount with some amount of ease somewhere on the console... I don't like those ones that stick on the windscreen.
Click to expand...
Click to collapse
www.brodit.com

Just don't order it from Expansys as all their product descriptions for Brodit are messed up. Does anyone know where else to buy Brodit because I still need the mounting clip for my car (Expansys kept sending the wrong one). Can you buy from them (Brodit) directly?
Thanks.

fixing small screen scratches

I posted a while ago about this with no response. I'd really appreciate some kind of input or advice or anything.
There are those of us who don't like screen protectors on our imates. Of course, after a year, this leads to those little, annoying scratches that seem to magically appear. There's stuff on the market to rub these out; one such product is Displex. I'd like to know if anyone has any experience with these products or any other methods of removing these tiny scratches.

If you haven't had a response in a year, I'd imagine that is because most people like the anti-glare and improved writing surface that a screen protector offers <shrug>
I know those scratches you're talking about but the first thing I do is to get a film for my new device to keep up the resale value.
I know this is a personal preference, but what do you have against films? I can't actually think of a downside to them apart from the first two attempts where you get dust under them and it annoys you for a week before you calm down enough to try it again =)
Maybe you could try one of these polishes and tell us how good they are, after all this information seems to be somewhat lacking ... ?

Amen to that. Actually the good brands (though a bit more expensive) of screen protectors are so easy to apply. I bought a couple of the ultra clear ones from Brando and i'm still on my first for close to a year now. Every now and then I clean the film with rubbing alcohol.
Since I own a few Swatch watches and most of them have already scratched plastic faces, I bought the little tube of scratch remover. It gets the job done but a lot of pressure is required especially if the scratch is very deep. Since my hands got very tired, I then used a Dremel. Word of advise, don't set the Dremel at a high speed because it will melt the plastic.
I don't know if the Magician's screen has some sort of anti-glare coating. When I tried to remove the scratches on my older pair of eye glasses, the anti-glare coating was taken off wether rubbing it manually or using the Dremel.

i've had only bad experiences with screen protectors. I guess that's what i get for being a cheap ass. Plus the jam is my first pda, so i never really realized how much of a problem those scratches really are.
I suppose the solution is to try the Displex screen scratch remover and then slap on a Writeshield AG. Thanks anyway.

I suggest you try first a very small area in a corner of the screen just in case the scratch remover will a a greater damage.
Good luck. Hope you do get your screen as good as new.

zerimar said:
I suggest you try first a very small area in a corner of the screen just in case the scratch remover will a a greater damage.
Good luck. Hope you do get your screen as good as new.
Click to expand...
Click to collapse
Absolutely. I once used scratch remover on my old XDA (Wallaby) and found it to be efective in removing the scratches. Problem - in the area where i removed the scratches the display was compromised - it looked like a prisma of kinds, kinda like when you little drops of liquid on an cathode ray tv - you could see little bits of red green and blue.
I think some kind of layer was removed causing this. So really try it on a corner before you go for the entire screen.
And another word, if you are not familiar with using a Dremel, NEVER use it for cleaning or polishing of plexiglass. I ruined a swatch with that. Used it even at a low speed, but the polishing wheel made the plexi so hot the watchglass actually looked like a bumpy road. Had it professionally repolished at a jewelers place, but by doing this the plexi had got so thin that i broke after a while...
Dremel and plexi - no good in my opinion.

i have a few scratches that came with my magician (i didnt pay a cent for the scratches ). let us know how you go.
BTW, has any one used car polisher for such a task? I heard (not sure how correct/accurate), that its possible to remove small scratchs from cds wih car polisher? I wonder if it works for lcds.
now how is man enough to try it out in there magicians hay :lol: :lol:

Camera scratches easily? Fixable in any way?

I have a small mark on my Camera already, and I've been handling my camera with extreme care this whole week/weekend thus far. I already have a pretty small scratch (not across the lens thankfully?) and I have no idea how it happened! Been moving my phone around very gently.
Is there anything I can do about the tiny scratch, or do I just have to live with it? I get pretty OCD about small things like this, so I need to make sure there's nothing I can do to try and remedy the scratch before flipping out.
Thanks everyone.

Kooper113 said:
I have a small mark on my Camera already, and I've been handling my camera with extreme care this whole week/weekend thus far. I already have a pretty small scratch (not across the lens thankfully?) and I have no idea how it happened! Been moving my phone around very gently.
Is there anything I can do about the tiny scratch, or do I just have to live with it? I get pretty OCD about small things like this, so I need to make sure there's nothing I can do to try and remedy the scratch before flipping out.
Thanks everyone.
Click to expand...
Click to collapse
The Silicone Sleeve sprint sold me for $11 after 25% off (Premier) and Tax lifts it up off any table

Relax. You and everybody else's phone will become dinged up. You are carrying it around with you all day everyday.

You can use the kickstand to keep it off the table or desk and use a case or pouch for carrying.

Use a liquid lens fixer like for glasses.

I cut a little piece from some old cheap screen protectors to cover mine. I'm sure there is some effect on the picture quality, but no current phone is going to compare to a Cannon anyway.

Resisting Lens Scratch
You can always buy a thick rubber washer and glue it around the camera lens. If you do not want to glue it, you can place it in between the cover and the phone. The solution is not fool proof, but it will work nicely to provide extra cushion and space. This solution is easy and cheap. The washer should not be to tight or small in diameter, so it does not interfere with the camera.
Kurt

kurtwoodfin said:
You can always buy a thick rubber washer and glue it around the camera lens. If you do not want to glue it, you can place it in between the cover and the phone. The solution is not fool proof, but it will work nicely to provide extra cushion and space. This solution is easy and cheap. The washer should not be to tight or small in diameter, so it does not interfere with the camera.
Kurt
Click to expand...
Click to collapse
Placing a rubber washer between the battery cover and the phone, would not do anything to keep the camera lens from resting on the surface that would scratch it.

kurtwoodfin said:
You can always buy a thick rubber washer and glue it around the camera lens. If you do not want to glue it, you can place it in between the cover and the phone. The solution is not fool proof, but it will work nicely to provide extra cushion and space. This solution is easy and cheap. The washer should not be to tight or small in diameter, so it does not interfere with the camera.
Kurt
Click to expand...
Click to collapse
I was thinking something along the lines of this. Basically you just need a ring that rests around the lens.
Something similar to this comes to mind. Of course, you wouldn't need to have a new lens on it. Just a piece of metal.
This could be magnetic, or glued. You could probably rip the phone apart and replace the piece with a more protruding piece to do the same, but that's far more intrusive.
I'm sure we'll see commercial magnet like solutions for this. I mean, come on. A small magnetic ring is all we need. Someone is going to bank on that.

Or how about using hoverboard technology so the phone never touches anything, and hovers in midair? Geez people, buy a case.

Jye75 said:
Or how about using hoverboard technology so the phone never touches anything, and hovers in midair? Geez people, buy a case.
Click to expand...
Click to collapse
Why cover the entire phone with a case when you can just put something around the lens?
I don't like cases. I think these devices were made to look and function in a certain way. If they "needed" a case it should have been built more robust.
I've had an iPhone 3G with no case for 2 years. I've also had no regrets.
Phone nudists unite!

ViViDboarder said:
Why cover the entire phone with a case when you can just put something around the lens?
I don't like cases. I think these devices were made to look and function in a certain way. If they "needed" a case it should have been built more robust.
I've had an iPhone 3G with no case for 2 years. I've also had no regrets.
Phone nudists unite!
Click to expand...
Click to collapse
It was sarcasm. I too, like mine naked, the way it was born. I have a leather case on my hip to put it in when I'm not using it. Jabbing at the fact that people actually want an accessory to attach to the camera lens ring just to keep it from touching another surface and getting scratched, like there should obviously be a market for that. Anyone that anal about possibly scratching a cellphone camera lens... I'm surprised they EVER pull the phone out to do anything at all. (again, sarcasm)

Jye75 said:
It was sarcasm. I too, like mine naked, the way it was born. I have a leather case on my hip to put it in when I'm not using it. Jabbing at the fact that people actually want an accessory to attach to the camera lens ring just to keep it from touching another surface and getting scratched, like there should obviously be a market for that. Anyone that anal about possibly scratching a cellphone camera lens... I'm surprised they EVER pull the phone out to do anything at all. (again, sarcasm)
Click to expand...
Click to collapse
Haha yea. It's a camera on a phone... My DSLR is in it's nice cushy case. My phone will reside, albeit tightly, in my pocket.

I put mine in my pocket up until today, when I got my HTC leather hip case. I got tired of the pocket lint getting in the earpiece grill.
Tip: use Scotch tape and a blunt tipped object to get the lint out of there.

Jye75 said:
I put mine in my pocket up until today, when I got my HTC leather hip case. I got tired of the pocket lint getting in the earpiece grill.
Tip: use Scotch tape and a blunt tipped object to get the lint out of there.
Click to expand...
Click to collapse
I've never used one of those before. I always feel like there's a risk of it falling out. Are they pretty secure?

ViViDboarder said:
I've never used one of those before. I always feel like there's a risk of it falling out. Are they pretty secure?
Click to expand...
Click to collapse
It's nice and snug. There's a hole on the bottom for your fingers to push the phone up to take it out. Magnetic flap, no metal button or anything, so no worries about phantom scratches. Stays close to the hip as well, and doesn't feel oversized or anything. Tight enough on the belt that I don't worry about it falling off.

Cool. I'll definitely check that out then. Thanks.

ViViDboarder said:
Cool. I'll definitely check that out then. Thanks.
Click to expand...
Click to collapse
The one I have is from Sprint online: Part Number CFH2258R

I got a case for mine simply because I've dropped my iPod touch a few times and I'm pretty sure it'd be damaged by now if it didn't have a silicon skin, the EVO's camera worried me as well... The silicon skin Sprint sells seems a lil' bulkier than it has to be tho, and the button bumps aren't as defined as they could be (my iPod touch's skin actually made the buttons easier to press, quite the opposite here). I'm waiting for a different more glossy/smooth skin from Amzer to ship before I decide if I'll just go naked or what...

i found cameraphone lens protector circles at a store called daiso near by me. works great

I did a carbon-look back cover :D

So i did this with 3m 1080 scotchprint carbon series and with nail scissors cutting it from 10x20cm took a while, about 2 hours to get it look nice i also cut a piece for the home button which took awhile too to get it fit perfectly!
to make this thread not so useless, recommend or post pictures of your customized gs2
anyway, what do you think ?

Looks excellent mate, would love a tutorial wouldn't mind that look myself.

Very nice...
Sent from my SGH-T959V using XDA App

Nice, I have a Samsung mesh case on mine which would cover that off

Does it say 0.8 MP?

That looks really nice, shame your not selling them

Its 0.8 because is on mirror ( 0.8 | 8.0 )

cost of this project was about 10-20 bucks. really, its not that difficult to make, just needs patience and good light. that is the first one i've ever made!
@itehappy most definitely hope its not a 0.8mp unit anyway nice to see people here from i8910 community!

Thanks for the prompt... Just ordered a sheet of 1200 x 300 for under $AUS 10 .
What did you cut it with? Just a normal sharp knife/razor blade? Any tips on cutting the corners, makig the holes, putting the sides and corners on etc???
I know it doesn't require a huge 20 page instruction book but if you could provide some tips or suggestions I think that would be great... Unless you plan on selling them then I suggest not to give the tips
Edit: Just realised you only did the back cover and not the edges... Maybe I will report back when I finally get my sheet and start cutting.

Nice! Tutorial would be appreciated!

When I read the thread title I imagined it would look tacky, but it actually looks really good

Nice. If you want to make some to sell I will buy.

I have a Silver one and you buy them online... o.o

looks great dude, what's the texture of the tape like though? The phone is slippy enough with the stock cover, with smooth tape it must be worse!

i want this too! Looks very nice!
Sent from my GT-I9100 using XDA App

+1 for you making them and selling them. (I don't have the patience)

viva.fidel said:
looks great dude, what's the texture of the tape like though? The phone is slippy enough with the stock cover, with smooth tape it must be worse!
Click to expand...
Click to collapse
It's actually textured, the "weave" is bumpy, raised a few cm, provides a bit of a rough, oil free surface without being uncomfortable. And you can do a fun DJ scratching imitation if you run your fingernail over it quickly.
I've been using it (they call it 3M Dynoc in North America) on the back of my SGS1 for over a year now, and on the back of my Tab 7" for nearly as long.
I couldn't be arsed to cut my own, so I bought mine pre-cut from PhantomSkinz (Skinomi also sells a very similar "skin"). The phone kit costs ~$25 before coupon, and it covers the entire back, the sides, and even comes with a wet-apply screen protector.
It's dead easy to apply, though the edges take a bit of practice...but if you screw up, just lift it up and try again.
It's durable as hell, the SGS1 has one minor, nearly invisible scratch in it after a year of abuse in my pocket, in my motorcycle jacket or tank bag, dirty tables, etc. They look far more "high tech" than the funky designs Samsung used on the back of those devices, especially the Tab.
Occasionally, I'd catch the bottom edge of the tape on the SGS with my fingernail when removing the battery cover and it'll lift a bit. Apply some heat and it goes right back into shape.
Little trick with the rough feel on the edges...heat it (desk lamp or hair dryer both work well) and run your fingernail over the edge...this thins it, making it much smoother.
I just placed an order with Skinomi for both a SGS2 and Galaxy Tab 10.1 "carbon" kit. On the SGS2, I'm thinking about leaving the battery cover naked since it's cheap to replace and already textured, and just using the carbon on the chin and sides. The chin on mine is starting to show some friction wear along the edge closest to the battery cover, and the sides get slippery as a bar of soap.

pbrown77 said:
Thanks for the prompt... Just ordered a sheet of 1200 x 300 for under $AUS 10 .
What did you cut it with? Just a normal sharp knife/razor blade? Any tips on cutting the corners, makig the holes, putting the sides and corners on etc???
I know it doesn't require a huge 20 page instruction book but if you could provide some tips or suggestions I think that would be great... Unless you plan on selling them then I suggest not to give the tips
Edit: Just realised you only did the back cover and not the edges... Maybe I will report back when I finally get my sheet and start cutting.
Click to expand...
Click to collapse
wait wait whaaat? 1200x300 for $10 dollars??!? is it 3M 1080 series or 3M Di-noc?
i cut all this with little scissors, about the length of a palm, maybe just a bit more. corners wont need any special stuff, just a hair dryer to get it a little more flexible. ONE THING, when i bought the carbon, I tought that i'll just bend anything which comes over the edge, to backside of the plate. well its not that easy. gs2 cover is so precisely cut that it doesnt allow any kind of extra stuff under the cover, so you just need to cut it little bit at a time, then try it, and cut a bit more and try, untill it fits properly. this will take most of the installation time. just be careful not to cut too much! same goes for the camera hole. very carefully and take the time it needs, even if there is 0.1mm too much, the camera wont fit properly. not difficult, but takes time. a hour atleast.
meh, im a nice guy, i'll give all the tips needed
@viva.fidel
the surface of the new 3M 1080 series has more rubbery feel than the Di-noc (what skinomi uses) and there is seriously good grip! Doesn't feel sticky, but still offers awesome grip believe me! maybe because of the carbon texture i dont know but has good grip for sure!
sorry if theres typos, wrote whole message with GS2 in PORTRAIT mode

Hi, If you were to sell any, I would buy one, It look really nice

ignore now!

[Guide] Turn your G4's glossy black edge into a matte black edge! No paint and easy!

DISCLAIMER: I am not responsible for any unwanted damage you may cause to your device, this is to be a sharing of an idea which happened to work for me and a sort of framework for how you may also accomplish this.
So basically, I despise how terribly fingerprints show on my G4's edge, that's a nit pick. My main complaint is that because it's a glossy plastic, it gets scratched very easily and shows that just as bad, not to mention it's obviously plastic masking as metal and not doing a good job, or more simply put, makes this flagship look cheap. I had a vision of a G4 with a flat black edge, I thought I'd grab a nail file from my bathroom -the giant popsicle stick ones- and use it to gently wear away at the shiny coating. My nail file had two sides, a fine side and a coarser side, I used the fine side exclusively with higher pressure strokes in the beginning to remove the shiny coating, using gentler and broader strokes to smooth, got one of those crazy nail file tools that have multiple sides and are made of two sides with softer layers of material in between, the two sides are also split into different functions, ones usually a buffer and the other is a super fine nail file, fine than the former one.....then I used this same tool to buff and clean up the edges and make sure all is smooth and nice, worked excellently, can also probably use super fine sandpaper and a cloth.
My back plate was off and battery removed, I used the popsicle nail file one side at a time starting with rougher strokes to get rid of the shiny coating -which will distinctly flake away as white little crumbs of plastic- it will take a few passes to completely strip the coating off the edge, you'll notice it lingers like a sort of residue as it contrasts quite distinctly against the revealed plastic, once the coating is nonexistent begin to smooth and finish the side until it is uniform in color and looks completely smooth, you want to keep the direction of the strokes consistent as it will impact the uniformity and smoothness, I went horizontally around the phone if it were laying flat and that gave me great results, give the corners some extra attention but its the same idea, and thanks to the battery back being off I was able to make the finish meet the edge of the battery door by angling the file accordingly, repeat these steps loosely and gently with either the multi-tool-file or extra fine grit sandpaper, use your judgment, buff and finish to your heart's desire. During the entire process be sure to regularly clean off the sandpaper, file and sides of the phone on a cloth of some sort between passes as you will notice the sandpaper glide and will be clogged with material, I was wearing some bumming pants so I just rubbed it off on those, worked wonderfully. Obviously you are removing incredibly small layers of material so guys be careful, you could probably remove quite a bit before anything happens but that can also effec look of things quite badly so try to make it even. I plugged important holes with bits of tissue, only the headphone jack really, the usb port is shallow enough where some air remove any particles.
The file helps especially because of its rigidity and shape, allowing me to have a lot of flexibility when dealing with such a small surface area.
You are putting files and sandpaper near your screen, be careful. I had a very good screen protecter but even then I didn't touch my screen once, you can get at a pretty steep angle like 45 degrees away from being parallel with the screen and still be fine, maybe less, just be wary, it's easy to slip and scratch, I don't think a soft brush would do much but a rough scratch could leave marks.
My IR blaster still works and it received the same treatment, I made no effort to avoid it.
I will post pictures soon, I wish I could use my phone to take a picture of my phone. I'll use someones phone tomorrow to do so.
Feel free to ask me anything if you have a question or I left some vital info out.
:laugh:

okay, waiting for the pics and a more detailed steps before jumping in.

superbonto said:
okay, waiting for the pics and a more detailed steps before jumping in.
Click to expand...
Click to collapse
So, I don't know how to post the pics cus as a new user I can't use links...

Also, you might consider adding a step of using progressively higher grits of sandpaper, and even going all the way to a rubbing compound to get super fine control over how much matte effect you desire. The matte of 300 grit sandpaper is different than the matte of say 450 grit etc.

KingFatty said:
Also, you might consider adding a step of using progressively higher grits of sandpaper, and even going all the way to a rubbing compound to get super fine control over how much matte effect you desire. The matte of 300 grit sandpaper is different than the matte of say 450 grit etc.
Click to expand...
Click to collapse
Yes absolutely, this is worth considering. I merely outlined how I did it to show that its not really necessary to get specific, I didn't go out of my way to get any of the tools I used and it came out satisfactory. I'll probably add it in once I get pics up and if people feel it's not as accessible as I thought.

mp2195 said:
So, I don't know how to post the pics cus as a new user I can't use links...
Click to expand...
Click to collapse
give us the link like www. linkhere.com/blah.img

mp2195 said:
So, I don't know how to post the pics cus as a new user I can't use links...
Click to expand...
Click to collapse
Use https://imgur.com/ to upload the picture and then post the direct link here, I'd love to see some pictures of this.

mp2195 said:
DISCLAIMER: I am not responsible for any unwanted damage you may cause to your device, this is to be a sharing of an idea which happened to work for me and a sort of framework for how you may also accomplish this.
So basically, I despise how terribly fingerprints show on my G4's edge, that's a nit pick. My main complaint is that because it's a glossy plastic, it gets scratched very easily and shows that just as bad, not to mention it's obviously plastic masking as metal and not doing a good job, or more simply put, makes this flagship look cheap. I had a vision of a G4 with a flat black edge, I thought I'd grab a nail file from my bathroom -the giant popsicle stick ones- and use it to gently wear away at the shiny coating. My nail file had two sides, a fine side and a coarser side, I used the fine side exclusively with higher pressure strokes in the beginning to remove the shiny coating, using gentler and broader strokes to smooth, got one of those crazy nail file tools that have multiple sides and are made of two sides with softer layers of material in between, the two sides are also split into different functions, ones usually a buffer and the other is a super fine nail file, fine than the former one.....then I used this same tool to buff and clean up the edges and make sure all is smooth and nice, worked excellently, can also probably use super fine sandpaper and a cloth.
My back plate was off and battery removed, I used the popsicle nail file one side at a time starting with rougher strokes to get rid of the shiny coating -which will distinctly flake away as white little crumbs of plastic- it will take a few passes to completely strip the coating off the edge, you'll notice it lingers like a sort of residue as it contrasts quite distinctly against the revealed plastic, once the coating is nonexistent begin to smooth and finish the side until it is uniform in color and looks completely smooth, you want to keep the direction of the strokes consistent as it will impact the uniformity and smoothness, I went horizontally around the phone if it were laying flat and that gave me great results, give the corners some extra attention but its the same idea, and thanks to the battery back being off I was able to make the finish meet the edge of the battery door by angling the file accordingly, repeat these steps loosely and gently with either the multi-tool-file or extra fine grit sandpaper, use your judgment, buff and finish to your heart's desire. During the entire process be sure to regularly clean off the sandpaper, file and sides of the phone on a cloth of some sort between passes as you will notice the sandpaper glide and will be clogged with material, I was wearing some bumming pants so I just rubbed it off on those, worked wonderfully. Obviously you are removing incredibly small layers of material so guys be careful, you could probably remove quite a bit before anything happens but that can also effec look of things quite badly so try to make it even. I plugged important holes with bits of tissue, only the headphone jack really, the usb port is shallow enough where some air remove any particles.
The file helps especially because of its rigidity and shape, allowing me to have a lot of flexibility when dealing with such a small surface area.
You are putting files and sandpaper near your screen, be careful. I had a very good screen protecter but even then I didn't touch my screen once, you can get at a pretty steep angle like 45 degrees away from being parallel with the screen and still be fine, maybe less, just be wary, it's easy to slip and scratch, I don't think a soft brush would do much but a rough scratch could leave marks.
My IR blaster still works and it received the same treatment, I made no effort to avoid it.
I will post pictures soon, I wish I could use my phone to take a picture of my phone. I'll use someones phone tomorrow to do so.
Feel free to ask me anything if you have a question or I left some vital info out.
:laugh:
Click to expand...
Click to collapse
I just came across this. I will be doing this tonight whn i get home from work. My otter box has scuffed mine pretty good. I like the nail file idea. Its work. Lol make u respect it a little more from the hard work.

make pressure on him so he shares the pics. :/

can the leathe from back cover be removed, am should be getting mine and it might be with leather.. i dont like it. just wondering if someone has taken the leather off the cover.. what it looks like. just plain molded plastic?

raptorddd said:
can the leathe from back cover be removed, am should be getting mine and it might be with leather.. i dont like it. just wondering if someone has taken the leather off the cover.. what it looks like. just plain molded plastic?
Click to expand...
Click to collapse
Dont do it! It will look horrendous! You better get a plastic back cover from eBay, I got one so I could use a Spigen Neo Hybid without damaging the leather back cover.

pakitos said:
Dont do it! It will look horrendous! You better get a plastic back cover from eBay, I got one so I could use a Spigen Neo Hybid without damaging the leather back cover.
Click to expand...
Click to collapse
i think leather looks GAY . no offense guys its just my opinion.. so it would be just a molded plastic right.? ill try see some stuff on amazon. what is the variant you have? is it from mexico..

raptorddd said:
i think leather looks GAY . no offense guys its just my opinion.. so it would be just a molded plastic right.? ill try see some stuff on amazon. what is the variant you have? is it from mexico..
Click to expand...
Click to collapse
Not molded plastic but lots of glue and sew points. Mine is from Telcel H815P

pakitos said:
Not molded plastic but lots of glue and sew points. Mine is from Telcel H815P
Click to expand...
Click to collapse
Unless glue cant be removed then itll look ugly... as foe the sewing points , thats a plu you get ventilation there.
this weather up north isnt very friendly... too bad you cant unlock bootloader.. whers the fun ?

Matte G4 Edge https://imgur.com/a/Bzspg

solventh said:
make pressure on him so he shares the pics. :/
Click to expand...
Click to collapse
Matte G4 Edge https://imgur.com/a/Bzspg

Thanks. Gold idea. Will try this when my broken test g4 arrives.
Can you pls seit the first post with the pics?

mp2195 said:
Matte G4 Edge https://imgur.com/a/Bzspg
Click to expand...
Click to collapse
thanks so much, man :]

Bullnados said:
Thanks. Gold idea. Will try this when my broken test g4 arrives.
Can you pls seit the first post with the pics?
Click to expand...
Click to collapse
For some stupid reason it won't let me edit my original post, weird. I'll try on my PC when I get a chance.

Perhaps to old?