Flashing RUU from fastboot - HTC Aria General

Yea, I was installing the CM7 ROM and on the first bootup it got stuck in a boot loop. There is a thread in the dev forum about this but its a little too technical (i just started learning).
So I tried to recover using nandroid but it didnt find my last backup for some reason.
So if someone can help me out with this issue that would be great thanks. Basically I need a little handholding for the problem with the solution provided here: http://forum.xda-developers.com/showthread.php?t=983452

Besure the power cable is unplugged then boot cwm once more reinstall then reboot phone..
Sent from my Liberty using Tapatalk

wontonforevuh said:
Yea, I was installing the CM7 ROM and on the first bootup it got stuck in a boot loop. There is a thread in the dev forum about this but its a little too technical (i just started learning).
So I tried to recover using nandroid but it didnt find my last backup for some reason.
So if someone can help me out with this issue that would be great thanks. Basically I need a little handholding for the problem with the solution provided here: http://forum.xda-developers.com/showthread.php?t=983452
Click to expand...
Click to collapse
That thread doesn't apply to you because you aren't stuck in a boot loop in the same sense of that thread's OP. Since you can still get into clockwork your issue is different. What you need to do is 1, see the post above this one. 2, did you format /system before flashing? 3, tell us how you got the ROM zip onto your SD Card (download on PC and transfer over? direct download from phone).

Related

clockwork partition woes

So im rooted, clockworked and nandroided. i go into rom manager and attempt to partition the sd, everything looks like it went fine. i get the samsung splash tmo bootup then it goes from the S splash screen to what seems to be a soft brick, just a blank screen and four lit up buttons. i try to boot into clockwork and i get the factory recovery mode. Clockwork is nowhere to be found. my sd card appears to be partitioned it shows a 14.8g card on a 16g, but the sd card still has everything on it, it did not get wiped. i have tried using odin, all that happens there is it runs through the motions, resets the phone back into this soft brick. anyone have similar issues or helpful ideas? i will be slowly bashing my head into the wall waiting for a reply. thanks in advance, any help will be appreciated
Same Problems Here
I came on to post and hopefully find a solution for a very similar problem. I rooted, clockworked, and nandroided my vibrant this morning and it worked fine all day. I got home and realized my phone was locked and didn't respond to the unlock button. I pulled the battery and rebooted and it all seemed fine. 5 minutes later i realized it wasn't responsive and once again pulled the battery and now won't boot past the "S" boot screen and seems to freeze. Now my clockwork restore won't backup and says it can't mount. I've tried a factory reset to no avail. Anytime I attempt a clockwork recovery I get the error
E:Can't mount /dev/block/mmcblk0p2
(file exists)
Can't mount /data/!
Any suggestions or solutions would be greatly appreciated.
I'm having the same issue, any help would be greatly appreciated.
did anyone get any help??
Same thing happened to me. I posted such on the market comment for rom manager. I ended up taking mine back to Best Buy (got another). I'm wanting to install linux on mine. Anyone been able to do that?
I hate to tell you this but you just partitioned the internal memory. If you had actually read the thread on clockwork recovery you would have seen that you cannot currently partition the external sd card with clockwork.
so what do i do??
nickerrides said:
so what do i do??
Click to expand...
Click to collapse
I honestly don't know the answer to that question. I'm kind of a casual flasher of my phones and I've never "bricked" one or had any major problem. I believe it can be fixed by using odin to flash back to stock. I'm pretty sure that you can recovery from it but it may take some work.
I would start by reading the entire clockwork recovery thread in the Android Development section. A few other people have made that mistake and may have a solution posted there. I'm at work posting from my phone or I would go look and try and find it.
Okay, I did some digging in that thread and it appears all you need to do is to use the re-partition option in Odin and then use Odin to flash a stock ROM and you should be all set.
Again, I have not used Odin myself so I don't know how easy/hard that is to do or if it will work at all.
nope i tried the repartition option in odin while flashing the stock rom.
With mine, I had success and got it out of the boot loop by using odin and flashing it back to stock.
The phone seems unbrickable, as
others have mentioned, just get it into download mode and use odin carefully.
Sent from my SGH-T959 using XDA App
wanna be more specific on what exactly you did?

[Q] OK so i know my GF's phone isnt bricked but...

Hey MT4G guru's i need your assistance.
1st off im an Evo user..rooted and all so im not to shabby at doing this. 2nd I rooted her phone using visionary.
So on to the problem. I tried to flash her a theme. I nandrioded (backup) first as usual. The theme which ended up being a full ROM--> http://forum.xda-developers.com/showthread.php?t=929101
It flashed successfully but when i rebooted it gets stuck at the white MT4G screen and stays there forever.
**I can still get into the bootloader & recovery.**
Tried to restore...NO LUCK. It restores, I reboot then the Same white screen.
Tried to factory reset, dalvik & cache wipe..... NO LUCK
Tried Update.zip Nothing!!!
Even tried pd15img in the bootloader. NOTHING!! It doesnt even recognize it!!
Guys i even looked into odin which i found out it isnt needed on phones with recovery.
Hate to sound like a noob but Help!!!!
...A fixed phone will result in 30,000 "thanks" button presses.....cause shes pissed to say the least....
Edit: Ok i believe i found the problem. I had clockwork 2.5.1.2 instead of 3 on her phone. Ok so now that i found the problem how do i fix it??
go to this link http://goo.gl/K0xTy and follow the instructions. you are flashing a cm7 rom and for this phone requires a different recovery. Then flash your rom
Flash cm6 first it will boot with 2.5
twiztid
If you made a nandroid backup, which you always should do before flashing a new rom, you can restore it using clockwork 2.5.1.2. If you don't have a backup you can do two things. You can use fastboot to flash clockwork recovery v3.0.0.5 to the phone then reboot into recovery and successfully flash CM7. If you don't know how to use fastboot then you can use the existing recovery to flash a froyo based rom on the phone. Either iced glacier or CM6 will flash ok. Perform a full wipe before you flash. Once you have a froyo rom working you can follow TrueBlue_Drew's thread about getting clockwork 3 on the phone without issue. I'm on my phone so I can't provide the link but it is in the mt4g development section. It is in a sticky called Resource Bible. In the OP, scroll until you see the header Recoveries and choose the link called Easiest way to install clockwork 3.0.0.5 by TrueBlue_Drew. Follow his instructions and you'll be able to switch between clockwork versions with no hassle. Of course, once you have clockwork 3 working you can flash CM7.
EDIT: Drew replied before I finished writing so follow his link once you are able to boot successfully.
Phillysphinest1 said:
Hey MT4G guru's i need your assistance.
1st off im an Evo user..rooted and all so im not to shabby at doing this. 2nd I rooted her phone using visionary.
So on to the problem. I tried to flash her a theme. I nandrioded (backup) first as usual. The theme which ended up being a full ROM--> http://forum.xda-developers.com/showthread.php?t=929101
It flashed successfully but when i rebooted it gets stuck at the white MT4G screen and stays there forever.
**I can still get into the bootloader & recovery.**
Tried to restore...NO LUCK. It restores, I reboot then the Same white screen.
Tried to factory reset, dalvik & cache wipe..... NO LUCK
Tried Update.zip Nothing!!!
Even tried pd15img in the bootloader. NOTHING!! It doesnt even recognize it!!
Guys i even looked into odin which i found out it isnt needed on phones with recovery.
Hate to sound like a noob but Help!!!!
...A fixed phone will result in 30,000 "thanks" button presses.....cause shes pissed to say the least....
Edit: Ok i believe i found the problem. I had clockwork 2.5.1.2 instead of 3 on her phone. Ok so now that i found the problem how do i fix it??
Click to expand...
Click to collapse
Swyped on my rooted MyTouch4G
XfooYen said:
If you made a nandroid backup, which you always should do before flashing a new rom, you can restore it using clockwork 2.5.1.2. If you don't have a backup you can do two things. You can use fastboot to flash clockwork recovery v3.0.0.5 to the phone then reboot into recovery and successfully flash CM7. If you don't know how to use fastboot then you can use the existing recovery to flash a froyo based rom on the phone. Either iced glacier or CM6 will flash ok. Perform a full wipe before you flash. Once you have a froyo rom working you can follow TrueBlue_Drew's thread about getting clockwork 3 on the phone without issue. I'm on my phone so I can't provide the link but it is in the mt4g development section. It is in a sticky called Resource Bible. In the OP, scroll until you see the header Recoveries and choose the link called Easiest way to install clockwork 3.0.0.5 by TrueBlue_Drew. Follow his instructions and you'll be able to switch between clockwork versions with no hassle. Of course, once you have clockwork 3 working you can flash CM7.
EDIT: Drew replied before I finished writing so follow his link once you are able to boot successfully.
Swyped on my rooted MyTouch4G
Click to expand...
Click to collapse
Dooohhh!!! Thanks for cleaning this up for me. I forgot to tell him he needed to DL and install a 2.2 rom using his current recovery if he cant restore the nandroid. on a side note....I'm typing this from my laptop that is using my wifi hotspot from my friends truck somewhere (middle of nowhere) in Colorado in a snow storm. got to love technology. I am also downloading the latest nightly. Only 28 minutes left on this slow edge connection, but at least its working
TrueBlue_Drew said:
Dooohhh!!! Thanks for cleaning this up for me. I forgot to tell him he needed to DL and install a 2.2 rom using his current recovery if he cant restore the nandroid. on a side note....I'm typing this from my laptop that is using my wifi hotspot from my friends truck somewhere (middle of nowhere) in Colorado in a snow storm. got to love technology. I am also downloading the latest nightly. Only 28 minutes left on this slow edge connection, but at least its working
Click to expand...
Click to collapse
Stay warm..
Swyped on my rooted MyTouch4G
TrueBlue_Drew said:
go to this link http://goo.gl/K0xTy and follow the instructions. you are flashing a cm7 rom and for this phone requires a different recovery. Then flash your rom
Click to expand...
Click to collapse
twiztidmyt4g said:
Flash cm6 first it will boot with 2.5
twiztid
Click to expand...
Click to collapse
UPDATE:
Ok.........(drum roll please)..........and the winner to the simplest answer that i should of thought of myself but i didnt cause i paniced is.....
TrueBlue Drew & Twiztidmy4g
All I needed to do was full wipe & flash a compatible ROM & it booted up fine!!!
**Attention XDA**
National crisis averted!!!! Woman is now satisfied. We nearly missed a nucular meltdown!! Thanks guys!!!!!
MODS PLEASE CLOSE OR COMPLETELY BURN & DELETE THIS WORTHLESS THREAD!!!!!
CM6 download
New to mt4g and have the same problem, i know i cant got o rom manager because i cant boot, can you provide a link to a cm6.zip file that i can run using clockwork 2.5.1.2
Thanks and yes i searched ont he forums for mt4g and i only see cm7 ....
"You can use fastboot to flash clockwork recovery v3.0.0.5 to the phone then reboot into recovery and successfully flash CM7. "
So how do you use fastboot to flash clockwork ? need help here i have clockwork on the sd card and installed using recovery but when i power volume down i am still in clockwork 2.5.1.2
How do i change clockwork to 3.0.0.5 from fastboot ?
Found it.... http://forum.xda-developers.com/showthread.php?t=876632
Installed it and then updated clockwork now in CM& ... wow Thanks .... ?
cmboud said:
So how do you use fastboot to flash clockwork ? need help here ......
Found it.... http://forum.xda-developers.com/showthread.php?t=876632
Installed it and then updated clockwork now in CM& ... wow Thanks .... ?
Click to expand...
Click to collapse
Didn't even have to reply. The search button is a marvelous thing. Good lad!
Swyped on my rooted MyTouch4G

Stuck at google logo, recovery mode doesn't work?

I seem to have messed up the process. I successfully unlocked and rooted my Nexus 7 but during wipe process using JROM flasher something didn't go right and now I'm stuck at the google logo screen forever. I can boot into fast recovery mode but that's about it. I can't do anything.
I've had this done before on my nexus phone but it seems I managed to f it up this time.
I thought I had a rom zip file copied on to the Nexus 7 but it doesn't show in the menu. Now I'm stuck at the logo screen not having access to any roms to install. How do I reset all of this to factory? I've already checked most of the threads regarding this and haven't been able to find a solution yet.
calavera-pw said:
I seem to have messed up the process. I successfully unlocked and rooted my Nexus 7 but during wipe process using JROM flasher something didn't go right and now I'm stuck at the google logo screen forever. I can boot into fast recovery mode but that's about it. I can't do anything.
I've had this done before on my nexus phone but it seems I managed to f it up this time.
I thought I had a rom zip file copied on to the Nexus 7 but it doesn't show in the menu. Now I'm stuck at the logo screen not having access to any roms to install. How do I reset all of this to factory? I've already checked most of the threads regarding this and haven't been able to find a solution yet.
Click to expand...
Click to collapse
before you do anything, use your recovery to see if the rom zip is located in /data/media/0/. if its there, flash it from that location.
Are you able to boot into recovery?
If yes, it could be as simple as plugging your tablet into the computer and mounting the usb, drag and drop the rom, and flash it without using a toolkit (only recovery). I'm not familiar with jrom flasher, but i will say the more variables there are, the more chance of a problem.
If no, you're best off running the stock factory image through your computer, found here: https://developers.google.com/android/nexus/images#nakasi. I had your problem at one point, and could not even boot into recovery. After trying to install cwm through adb (which failed), and a number of toolkits, the factory image was what brought my nexus back to life.
I remember reading that sometimes a wipe can delete your recovery as well as your system (and whatever else you have on your n7), although i dont know if that was ever fixed, as i got my tab replaced a month or two ago and havent rooted it again yet. There was some type of command or .zip or something that should be used to keep recovery after wipes. When i expirienced problems such as yours, it was also from a bad wipe from a toolkit. Using just the recovery afterwards, i never expirienced any issues, even without the recovery fix.
I would definitely try simms suggestion first if you can access recovery. If that fails, try one of the above processes.
PS, even if you can access recovery, if at this point you just want to go completely stock, the factory image will work regardless.
cheers
Thanks for the help guys, I've been struggling for the past 3~4 hours but I found a solution.
What I did was use JROMFlasher and upload a rom zip to the sdcard directly and go from there.
calavera-pw said:
Thanks for the help guys, I've been struggling for the past 3~4 hours but I found a solution.
What I did was use JROMFlasher and upload a rom zip to the sdcard directly and go from there.
Click to expand...
Click to collapse
Guys..I have the similar problem..I am not able to upload rom zip to sdcard using JROMFlasher..Also USB mounting is not working for me ..
Is there any other way to move ROM to sdcard?:crying:
appoos said:
Guys..I have the similar problem..I am not able to upload rom zip to sdcard using JROMFlasher..Also USB mounting is not working for me ..
Is there any other way to move ROM to sdcard?:crying:
Click to expand...
Click to collapse
ADB
Sent from my Galaxy Nexus
Pirateghost said:
ADB
Sent from my Galaxy Nexus
Click to expand...
Click to collapse
This dint work in my windows 8
appoos said:
This dint work in my windows 8
Click to expand...
Click to collapse
You're holding it wrong. ADB works on my Win8 machine
Pirateghost said:
You're holding it wrong. ADB works on my Win8 machine
Click to expand...
Click to collapse
can you tell me the procedure..
appoos said:
can you tell me the procedure..
Click to expand...
Click to collapse
no.
in the other thread that YOU created, you were given links to follow and the instructions are already there. i dont hold hands
I could do it with ADB..thanks guys

Phone stuck on "Samsung - Custom" screen after creating TWRP backup. Help please?

Phone stuck on "Samsung - Custom" screen after creating TWRP backup. Help please?
I have an ATT S4, that has had CM 10.1 on it running flawlessly pretty much since nightlies started to get released. Decided to try going back to some TW based ROMs. Running the latest nightly, loaded up TWRP, created a backup, as I usually do before swapping roms. Created the backup fine, now it won't boot, it just sits at the Samsung screen with the lock and Custom message. Wiped cache\dalvic, even tried restoring from the backup I just created. Nothing. Tried it with the phone plugged into the computer and without being plugged in (I think I recall it being plugged into USB could cause issues in the past), and still nada. Tried pulling the battery and rebooting about 10 times. Can get into recovery and odin mode perfectly fine still. Any suggestions or ideas? Thanks
Simonzi said:
I have an ATT S4, that has had CM 10.1 on it running flawlessly pretty much since nightlies started to get released. Decided to try going back to some TW based ROMs. Running the latest nightly, loaded up TWRP, created a backup, as I usually do before swapping roms. Created the backup fine, now it won't boot, it just sits at the Samsung screen with the lock and Custom message. Wiped cache\dalvic, even tried restoring from the backup I just created. Nothing. Tried it with the phone plugged into the computer and without being plugged in (I think I recall it being plugged into USB could cause issues in the past), and still nada. Tried pulling the battery and rebooting about 10 times. Can get into recovery and odin mode perfectly fine still. Any suggestions or ideas? Thanks
Click to expand...
Click to collapse
There are no less than a dozen similar threads about similar problems already. Have you looked at those threads for a possible solution yet? You can find them by using the search function or better yet just doing a visual search of the first few pages of the "General" and "Q&A" sections. Good luck.
Sounds like a ROM and kernel issue. Try flashing a ROM with a loki'd kernel.
Tylorw1
Sent from my SAMSUNG-SGH-I337 using Tapatalk 4
Tylorw1 said:
Sounds like a ROM and kernel issue. Try flashing a ROM with a loki'd kernel.
Tylorw1
Sent from my SAMSUNG-SGH-I337 using Tapatalk 4
Click to expand...
Click to collapse
I don't see how that could be the case. I didn't flash anything. I just loaded TWRP, created a backup, and rebooted my phone. No ROM\kernel change. Nothing more than creating a backup in TWRP.
scott14719 said:
There are no less than a dozen similar threads about similar problems already. Have you looked at those threads for a possible solution yet? You can find them by using the search function or better yet just doing a visual search of the first few pages of the "General" and "Q&A" sections. Good luck.
Click to expand...
Click to collapse
I tried searching, the closest one I could find on the first few pages was this one. I just didn't see any specific to my situation because nothing was flashed. Like my response to Tylorw1, all I did was boot into recovery, create a backup, and reboot my phone. Didn't flash a ROM, change a kernel, format anything, etc...
I has this same problem... It happened after every single reboot after flashing various ROMs or anything.. I gave up and went back to CWM and haven't had the problem since :good:
Sent from my SGH-I337 using xda app-developers app
Simonzi said:
I have an ATT S4, that has had CM 10.1 on it running flawlessly pretty much since nightlies started to get released. Decided to try going back to some TW based ROMs. Running the latest nightly, loaded up TWRP, created a backup, as I usually do before swapping roms. Created the backup fine, now it won't boot, it just sits at the Samsung screen with the lock and Custom message. Wiped cache\dalvic, even tried restoring from the backup I just created. Nothing. Tried it with the phone plugged into the computer and without being plugged in (I think I recall it being plugged into USB could cause issues in the past), and still nada. Tried pulling the battery and rebooting about 10 times. Can get into recovery and odin mode perfectly fine still. Any suggestions or ideas? Thanks
Click to expand...
Click to collapse
what version of twrp? if it is 2.6.?.? then get off of it, also, what I did was pull battery for 3min, it booted fine....go back to early version of twrp...
STVERDI said:
I has this same problem... It happened after every single reboot after flashing various ROMs or anything.. I gave up and went back to CWM and haven't had the problem since :good:
Sent from my SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
I've wanted to go back to CWM. That's what I had on my S3. Only thing stopping me, is all my nandroid backups for my S4 are done with TWRP, and I don't want to run into a situation where I need them, and them not being compatible
TheAxman said:
what version of twrp? if it is 2.6.?.? then get off of it, also, what I did was pull battery for 3min, it booted fine....go back to early version of twrp...
Click to expand...
Click to collapse
Nope, still on 2.5.0.2. Finally, after a third complete wipe/format and restore from the back I had created (the one that started the whole issue), it works fine. Such a huge pain in the ass.
a user had to boot back into twrp and wipe data/factory reset yesterday to fix this issue.
Simonzi said:
I've wanted to go back to CWM. That's what I had on my S3. Only thing stopping me, is all my nandroid backups for my S4 are done with TWRP, and I don't want to run into a situation where I need them, and them not being compatible
Nope, still on 2.5.0.2. Finally, after a third complete wipe/format and restore from the back I had created (the one that started the whole issue), it works fine. Such a huge pain in the ass.
Click to expand...
Click to collapse
And you have to be ****ing kidding me. I rebooted into recovery while typing my initial response, just to verify I was still on the 2.5.x.x TWRP. Booted up TWRP, verified that, choose "Reboot System", and same thing. Back to sitting at the Samsung screen. Nandroid backups or not, ditching TWRP as soon as I get it able to boot back up.
Even worse off now than when I started. After my last post, where my phone was doing the same "stuck on Samsung logo" thing, just from booting into TWRP, I decided to swap to a different recovery. Searched for "switch from TWRP to CWM", and found my own post I had made a few months ago, but never went through.
Following those instructions now, I decided on the PhilZ CWM. Head over to that thread, grab the loki'd zip, load up TWRP, and flash the zip. Now I can't even boot into recovery!! It just freezes on the Samsung screen with the blue "recovery booting" text.
Can still get into download mode, so I tried using ODIN to flash PhilZ jflteatt.tar.md5 file, and it fails.
At this point, waiting for the stock 1.6 firmware package to download, so I can just ODIN that.
If anyone has any other suggestions though, they'd be great. Have an hour to try while waiting for that to download
somebody had mentioned this...
http://forum.xda-developers.com/showpost.php?p=44629460&postcount=8
make sure you have the correct firmware and proceed as you are. likely your best bet.
Simonzi said:
Even worse off now than when I started. After my last post, where my phone was doing the same "stuck on Samsung logo" thing, just from booting into TWRP, I decided to swap to a different recovery. Searched for "switch from TWRP to CWM", and found my own post I had made a few months ago, but never went through.
Following those instructions now, I decided on the PhilZ CWM. Head over to that thread, grab the loki'd zip, load up TWRP, and flash the zip. Now I can't even boot into recovery!! It just freezes on the Samsung screen with the blue "recovery booting" text.
Can still get into download mode, so I tried using ODIN to flash PhilZ jflteatt.tar.md5 file, and it fails.
At this point, waiting for the stock 1.6 firmware package to download, so I can just ODIN that.
If anyone has any other suggestions though, they'd be great. Have an hour to try while waiting for that to download
Click to expand...
Click to collapse
Stock 1.6 firmware package?
Make sure you get the correct firmware? Go to SamMobile and get the stock firmware from there or go to Adam Outlers "Stock firmware ODIN" thread in the General section (the AMDL firmware link is in that thread you just have to look for it).
scott14719 said:
Stock 1.6 firmware package?
Make sure you get the correct firmware? Go to SamMobile and get the stock firmware from there or go to Adam Outlers "Stock firmware ODIN" thread in the General section (the AMDL firmware link is in that thread you just have to look for it).
Click to expand...
Click to collapse
Yeah, I meant 1.6gb firmware package. Just forgot the "gb". That's what I'm currently downloading, but trying to recover it with Kies while waiting.
I would like to report I had the same problem.
After changing roms and making a nandroid, and then deciding to switch roms again, I ran into the stuck at Samsung Custom with a lock boot screen. Most roms would boot up once, but a restart or power down would lead to being stuck. I was flashing through TWRP.
I went into TWRP and flashed OUDHS recovery which overrode TWRP and wiped/flashed through OUDHS a new rom.
Problem solved.
S3 at&t stuck in TWRP booting screen.
xBeerdroiDx said:
a user had to boot back into twrp and wipe data/factory reset yesterday to fix this issue.
Click to expand...
Click to collapse
Im new to custom roms, I pressed ok for an update on my phone, after the update was complete my phone shut off and booted into TWRP and now I can't get back to my android screen nor make calls etc. HELPPPPPPPP PLEASSSSSEE I have been trying to fix my phone since july and I have been using this cheap phone that don't even get internet. I have an S3 1747 at&t
Lnjames said:
Im new to custom roms, I pressed ok for an update on my phone, after the update was complete my phone shut off and booted into TWRP and now I can't get back to my android screen nor make calls etc. HELPPPPPPPP PLEASSSSSEE I have been trying to fix my phone since july and I have been using this cheap phone that don't even get internet. I have an S3 1747 at&t
Click to expand...
Click to collapse
Wrong forum. Please go to the s3 section with your question.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
Had this problem just now, solved it by fixing permissions.
I am running an MDL based S4, and screwed the pooch. I was going to wipe the internal storage and made the mistake of doing it through TWRP 2.5. Now, I have the same problem of being stuck on the custom boot screen. I have tried to change from TWRP to OUDHS Recovery, but still boot loops to Custom screen. I have tried fresh installs of 4.2 ROMs and 4.4.2 Google Editions. Do I need to flash via ODIN?
Flame away....I know better than this!!!!
Help would be greatly appreciated.
Sent from my GT-N8013 using Tapatalk 4

[Q] Help a noob, cannot boot after trying to flash stock rom

So I'm pretty desperate and I apologize if similar info was posted somewhere else. I've been researching several hours but couldn't find anything.
I originally installed CM11 and decided to experiment with a different rom TriForce ROM [TouchWiz]. I put the zip file on my SD card and booted into clockworkmod it gave an error of bad zip. I tried different usb port to transfer the zip, downloaded it multiple times with no result. So I decided to try a different rom Stock_Rooted_Deodexed_MF9_Rom.zip. The installation finished but the phone would not boot.
Recently I flashed the stock rom from odin, it finished successfully but still not boot, Galaxy sreen lights up quickly and that's it.
rmngorelov said:
So I'm pretty desperate and I apologize if similar info was posted somewhere else. I've been researching several hours but couldn't find anything.
I originally installed CM11 and decided to experiment with a different rom TriForce ROM [TouchWiz]. I put the zip file on my SD card and booted into clockworkmod it gave an error of bad zip. I tried different usb port to transfer the zip, downloaded it multiple times with no result. So I decided to try a different rom Stock_Rooted_Deodexed_MF9_Rom.zip. The installation finished but the phone would not boot.
Recently I flashed the stock rom from odin, it finished successfully but still not boot, Galaxy sreen lights up quickly and that's it.
Click to expand...
Click to collapse
Restore from nandroid backup. I hope you made one. Try going into recovery do a factory reset and wipe all cache and data and what not and then install a ROM from Odin.
rmngorelov said:
So I'm pretty desperate and I apologize if similar info was posted somewhere else. I've been researching several hours but couldn't find anything.
I originally installed CM11 and decided to experiment with a different rom TriForce ROM [TouchWiz]. I put the zip file on my SD card and booted into clockworkmod it gave an error of bad zip. I tried different usb port to transfer the zip, downloaded it multiple times with no result. So I decided to try a different rom Stock_Rooted_Deodexed_MF9_Rom.zip. The installation finished but the phone would not boot.
Recently I flashed the stock rom from odin, it finished successfully but still not boot, Galaxy sreen lights up quickly and that's it.
Click to expand...
Click to collapse
Make sure you're using roms for your version of your phone. the MF9 bootloader is really old and probably wont install anymore. My phone did this before and I thought I bricked it, but I kid you not I took the battery out and removed the SIM card and rebooted and it booted up just fine. May not work for you, but I suggest you go back to update stock firmware then try again. If you're using the triband model, there's a post around here somewhere with confirmed roms that wont brick your device. I'm currently using the Google Play Edition Stock ROM and it's working GREAT.
Link for new firmware (NG5 Firmware): https://mega.co.nz/#F!0JdRkIZR!AqqKdbvba_Hpg5VrCmrbPw
i7vSa7vi7y said:
Restore from nandroid backup. I hope you made one. Try going into recovery do a factory reset and wipe all cache and data and what not and then install a ROM from Odin.
Click to expand...
Click to collapse
I restored to this stock ROM before and everything worked well. Currently I can't boot into recovery, Samsung flashes once and that's it, that's why I'm desperate the only thing I can do is boot in to download mode for odin.
silentdeath631 said:
Make sure you're using roms for your version of your phone. the MF9 bootloader is really old and probably wont install anymore. My phone did this before and I thought I bricked it, but I kid you not I took the battery out and removed the SIM card and rebooted and it booted up just fine. May not work for you, but I suggest you go back to update stock firmware then try again. If you're using the triband model, there's a post around here somewhere with confirmed roms that wont brick your device. I'm currently using the Google Play Edition Stock ROM and it's working GREAT.
Link for new firmware (NG5 Firmware):
Click to expand...
Click to collapse
Does it matter that I can't get into recovery to clear the cache first before trying new roms?
silentdeath631 said:
Make sure you're using roms for your version of your phone. the MF9 bootloader is really old and probably wont install anymore. My phone did this before and I thought I bricked it, but I kid you not I took the battery out and removed the SIM card and rebooted and it booted up just fine. May not work for you, but I suggest you go back to update stock firmware then try again. If you're using the triband model, there's a post around here somewhere with confirmed roms that wont brick your device. I'm currently using the Google Play Edition Stock ROM and it's working GREAT.
Link for new firmware (NG5 Firmware):
Click to expand...
Click to collapse
Maybe I'm doing something foolish but every time I try to download files from the link you gave I get a decryption error so I can't download them zip or original.
rmngorelov said:
I restored to this stock ROM before and everything worked well. Currently I can't boot into recovery, Samsung flashes once and that's it, that's why I'm desperate the only thing I can do is boot in to download mode for odin.
Click to expand...
Click to collapse
Just hold home power and volume up. Right when you see text at the top left let go. You have to have the right timing
i7vSa7vi7y said:
Just hold home power and volume up. Right when you see text at the top left let go. You have to have the right timing
Click to expand...
Click to collapse
After almost eight hours of troubleshooting I finally got it to work.
I've tried flashing clockworkmod several times to see if I could get into recovery with no result so I gave up on that and I flashed the newest stock rom I could find L720VPUFNG2_L720SPTFNG2_SPR and it was still not booting. Than I thought maybe twerp would make a difference and god almighty it finally booted! I felt as if I gave birth to a child after eight hours of labor!
Now I'm extremely paranoid about touching anything because it took me forever to do this. Does anyone know why flashing twerp would make such a difference? I know this sort of stuff can get extremely complicated but I'd like to try to understand.
I hope my foolish agony contributed to this community if not in any other way except by the comedic relief caused by my ignorance.
rmngorelov said:
After almost eight hours of troubleshooting I finally got it to work.
I've tried flashing clockworkmod several times to see if I could get into recovery with no result so I gave up on that and I flashed the newest stock rom I could find L720VPUFNG2_L720SPTFNG2_SPR and it was still not booting. Than I thought maybe twerp would make a difference and god almighty it finally booted! I felt as if I gave birth to a child after eight hours of labor!
Now I'm extremely paranoid about touching anything because it took me forever to do this. Does anyone know why flashing twerp would make such a difference? I know this sort of stuff can get extremely complicated but I'd like to try to understand.
I hope my foolish agony contributed to this community if not in any other way except by the comedic relief caused by my ignorance.
Click to expand...
Click to collapse
Depends what recovery you had and what version. I personally like Philz touch recovery but TWRP is good. Now wipe and flash a ROM my friend or restore a backup
rmngorelov said:
After almost eight hours of troubleshooting I finally got it to work.
I've tried flashing clockworkmod several times to see if I could get into recovery with no result so I gave up on that and I flashed the newest stock rom I could find L720VPUFNG2_L720SPTFNG2_SPR and it was still not booting. Than I thought maybe twerp would make a difference and god almighty it finally booted! I felt as if I gave birth to a child after eight hours of labor!
Now I'm extremely paranoid about touching anything because it took me forever to do this. Does anyone know why flashing twerp would make such a difference? I know this sort of stuff can get extremely complicated but I'd like to try to understand.
I hope my foolish agony contributed to this community if not in any other way except by the comedic relief caused by my ignorance.
Click to expand...
Click to collapse
im having similar issues. which version of TWRP worked for you?
thank you
fearthemarchx said:
im having similar issues. which version of TWRP worked for you?
thank you
Click to expand...
Click to collapse
I recommend flashing the newest one here using odin
http://teamw.in/project/twrp2
Then once you are able to boot into recovery go to wipe and perform both factory reset and format data. Then install whatever rom you like, I used Sprint Galaxy S4 SPH-L720 VPUFNAE (Androdi 4.4.2) found here
http://galaxys4root.com/galaxy-s4-stock-firmware/ (or maybe find a newer stock rom if this one gives you errors)
Just copy the zip file to the phone, boot into twrp, do wipe factory reset again, select install then select the zip in whatever directory and you should be good to go. Make sure you do a back up in twrp once you get the phone to boot so you can always revert to stock.
I hope I was thorough enough that some of the information was useful. Let me know if you need any more help.
only certain recoveries will stick. ive tried the most recent twrp, with no luck. only a few versions of philztouch work.
Sent from my LGL34C using XDA Free mobile app
fearthemarchx said:
only certain recoveries will stick. ive tried the most recent twrp, with no luck. only a few versions of philztouch work.
Sent from my LGL34C using XDA Free mobile app
Click to expand...
Click to collapse
Format with philztouch that works then try flashing a new stock rom with odin. That should bring everything back to stock including the recovery.
ive tried. when i flash rom via odin i only get a blue "recovery booting" at the top of boot screen. even when i only power on, not into recovery. im going to attempt to flash rom provided in previous post via philz.
Sent from my LGL34C using XDA Free mobile app
fearthemarchx said:
ive tried. when i flash rom via odin i only get a blue "recovery booting" at the top of boot screen. even when i only power on, not into recovery. im going to attempt to flash rom provided in previous post via philz.
Sent from my LGL34C using XDA Free mobile app
Click to expand...
Click to collapse
You're in download mode when you flash from odin right? If you your getting an error flashing, try a different stock rom after reformating/resetting to factory (it's crucial to clear the cache before trying a different rom). I had to try a few roms before I found one that worked.

Categories

Resources