Creaking Back on Atrix? - Atrix 4G General

Hey guys,
This is my first post on the forums, so I hope it goes well... I did a search and couldn't find anything like what I was looking for, so I figured I would write a new thread.
I got my atrix a little over a week ago now, and really like it. The only small issue I have found is with the back of the phone/ fingerprint reader. The back of the phone has a general weird creaking about it. The two places i get this the most are at the sides near where it clips in (I checked to make sure the clips are firmly in place) and kind of the top center... about even with the camera and down from the fingerprint reader. In the second spot, there is a kind of weird give to it that pops up and down, and makes a little noise.
The other issue is a weird thing with the fingerprint reader. I noticed this like the third day I had it, but the "sticker" that covers up the fingerprint reader is oddly crooked. Probably not a big deal, but it is a little bothersome on a brand new phone.
Has anyone had these issues at all? Could they perhaps be fixed by just doing a quick swap of the back for a new one, or is it perhaps a more serious problem? I really don't want to be a pain and make them swap out the phone for a new one over a stupid creaking back, but it really bothers me... I am a bit of a stickler for build quality.
Thanks in advance for any thoughts

Well I mean, if you're having hardware defects then you can only... pretty much take the phone back.
If you can get over it then that's great, but if you're stuck with the phone for 2 years, I'd get a new one.

HAD same problem with the back creaking. Just get some thin tape (I used 3m masking tape) and cover the tabs wit small piece of the tape.
I did this to the whole cover and now its SOLID all around!
bearsfan172 said:
Hey guys,
This is my first post on the forums, so I hope it goes well... I did a search and couldn't find anything like what I was looking for, so I figured I would write a new thread.
I got my atrix a little over a week ago now, and really like it. The only small issue I have found is with the back of the phone/ fingerprint reader. The back of the phone has a general weird creaking about it. The two places i get this the most are at the sides near where it clips in (I checked to make sure the clips are firmly in place) and kind of the top center... about even with the camera and down from the fingerprint reader. In the second spot, there is a kind of weird give to it that pops up and down, and makes a little noise.
The other issue is a weird thing with the fingerprint reader. I noticed this like the third day I had it, but the "sticker" that covers up the fingerprint reader is oddly crooked. Probably not a big deal, but it is a little bothersome on a brand new phone.
Has anyone had these issues at all? Could they perhaps be fixed by just doing a quick swap of the back for a new one, or is it perhaps a more serious problem? I really don't want to be a pain and make them swap out the phone for a new one over a stupid creaking back, but it really bothers me... I am a bit of a stickler for build quality.
Thanks in advance for any thoughts
Click to expand...
Click to collapse

happens to me too i think its just the design of the cover. no biggie.

bearsfan172 said:
Hey guys,
The other issue is a weird thing with the fingerprint reader. I noticed this like the third day I had it, but the "sticker" that covers up the fingerprint reader is oddly crooked. Probably not a big deal, but it is a little bothersome on a brand new phone.
Click to expand...
Click to collapse
mine dosnt look crooked, but it does appear as though its starting to peel off on one corner

Same
I noticed the exact same two things as the OP. Disappointing for me too (although minor). I was used to rock-solid Nexus One.

My phones fingerprint reader is crooked, which is oddly very very annoying. The screen is also flush on the left side, yet recessed on the right side.

cataclysmicvoid said:
I noticed the exact same two things as the OP. Disappointing for me too (although minor). I was used to rock-solid Nexus One.
Click to expand...
Click to collapse
Yeah. If that's the way it is, it isn't the end of the world to me. I came from the iPhone 4 which... say what you will about apple, but their build quality and consistency is generally very very good.
A bit disappointing to me that a beautiful new phone would have annoyances like a back that doesn't sit quite right... but there are worse things in the world really.

Related

adhesive loosening on HD2?

--
thats how mine is but in the bottom. not a big deal but i did feel it
several people reported the same thing before. screen not flush all the way around. there's no adhesive, the screen slides out of the outer sleeve if you remove the screws in back.
Oh...
--
mine does it on the bottom.
it feels like there is a slight gap in between the bottom bezel and the screen.
It's not a problem at all, but it sure is annoying at times.
On the left side of my HD2 the screen is easier to push in at the top and bottom, but it takes a lot of pressure to make it "squeak".
If I had a cosmetic issue, you can bet I would be on a waiting list to get a replacement. The looks on these phones are nearly as important as the performance, IMHO.
oh i deff agree, @op, if you only just got it id be trying to take it back.
Same on mine at the bottom - just barely - if you slightly press between the usb and headphone jack you hear a slight (guess it sounds like) a click and you feel it slightly move. When the usb jack is plugged in it stops Some play and I don't think its worth returning - also don't think it will get worse. Case materials should have been a little more rigid. Think if you get a hard shell case or aluminum skin - when they become available you won't notice it. Talking to other guys with the HTC branded Euro version their build quality is a bit better. Think its pretty much the same with all HTC stuff - their branded models (TYTN TYTN II etc.) were build better than the AT&T versions - they also cost a lot more because they aren't subsidized.
Personally feel the HD2 of all the MS phones with the exception of the HTC TYTN I is the most solid. The Fuze which I just got rid of was probably the worst. The case was ok but the front keypad was pure junk - out of the box the thing felt like it was going to break and it never sat "square" in its opening. The USB ports on all of them were really weak and were super loose out of the box. The slide out keyboards always loosened up and had too much play.
stim141 said:
Personally feel the HD2 of all the MS phones with the exception of the HTC TYTN I is the most solid. The Fuze which I just got rid of was probably the worst. The case was ok but the front keypad was pure junk - out of the box the thing felt like it was going to break and it never sat "square" in its opening. The USB ports on all of them were really weak and were super loose out of the box. The slide out keyboards always loosened up and had too much play.
Click to expand...
Click to collapse
For me, the Touch Pro 2 has top honors when it comes to "feeling" solid. My sister dropped it the other day and cracked the bevel, with a large triangle missing near the volume rocker and three other cracks on the bottom, top and opposite side.
I am encouraging her to return it and claim the insurance, but since there is no change in the quality of the phone's operation, she wants to keep it.
Again, for me, the TP2 seems more solid than the HD2, but the HD2 is very well-built compared to other phones. I am so paranoid about even putting my phone down on a hard surface, due to the sharp edges of the camera mount and the light metal case.
I will be installing my new invisibleSHEILD as soon as sirphunkee and I can make the time to meet somewhere clean (I have a 2yo at home ). I imagine my paranoia will drop a bit then...
I dropped my phone while working out at the gym.
I was on the treadmill, and dropped the phone from my hand to the treadmill belt, then it flew out (i was running pretty fast at speed 7) and ended up hitting the wall behind me. Well, I freaked out and ran over to check on the phone.
Even though I had NO protection, the phone was perfectly fine. Only a tiny scratch that's barely visible on the top left bezel, and everything was fine.
I really was surprised at the sturdiness of the phone.
Snarksneeze said:
For me, the Touch Pro 2 has top honors when it comes to "feeling" solid. My sister dropped it the other day and cracked the bevel, with a large triangle missing near the volume rocker and three other cracks on the bottom, top and opposite side.
I am encouraging her to return it and claim the insurance, but since there is no change in the quality of the phone's operation, she wants to keep it.
Again, for me, the TP2 seems more solid than the HD2, but the HD2 is very well-built compared to other phones. I am so paranoid about even putting my phone down on a hard surface, due to the sharp edges of the camera mount and the light metal case.
I will be installing my new invisibleSHEILD as soon as sirphunkee and I can make the time to meet somewhere clean (I have a 2yo at home ). I imagine my paranoia will drop a bit then...
Click to expand...
Click to collapse
My TP2 fell out of my hand in a parking lot, the thing didn't hit hard, but it left a small scratch on the screen (it was visible, but wasn't too obvious) and then some nicks at the corners of the device. It did look used. I returned it to T-Mo (I was still within 14-day remorse period) and used the money I got back to get an HD2 instead (for some reason I didn't qualify for either the full or the 11 month upgrade price, only 50 bucks discount... now that I think about it, I should have gotten it at full price, also, the day after it arrived (ordered online) T-Mo came out with the 2 for 1 smartphone, but alas, a new line was needed and I had no use for it).
I've dropped my HD2 at least 4 times since and there's not a nick on it. I figure the glass screen helps (as opposed to the TP2's plastic), even if it's a finger print magnet. I also have no problems with the screen or bezel being uneven, even after dropping it, nor have I had any single of the problems people complain about, so, go figure, I got the perfect production HD2.
Whew.... OK. Soooo glad to hear this isnt only my device. Mines is on the bottom. I also dont see it getting any worst and its so minor right now its probably not worth the hassle of returning. I tend to keep the gel case on it anyway..
thrashingdeth said:
thats how mine is but in the bottom. not a big deal but i did feel it
Click to expand...
Click to collapse
x2 same as mines.
--
I had an issue with mine creaking, on the bottom. Mainly when I was pressing the start key, or back. Got a replacement and it seems better. For a phone seriously delayed I don't get how the quality is so terrible.
my first hd2 the camera lens started to rattle tmobile replaced it
Tm5078 said:
my first hd2 the camera lens started to rattle tmobile replaced it
Click to expand...
Click to collapse
Was it the camera lens or the casing around the camera?
After watching the tear-down video I could see how the camera casing could be improperly installed and loosen after a bit of handling, but I thought the lens was pretty solid...
--
JWang158 said:
Seriously, this phone is turning out to be pretty half baked.
Click to expand...
Click to collapse
I disagree. Not sure if I got lucky or not, but my phone is in perfect condition despite being a month old and spending most of that time in my back pocket.
I've sat on it countless times, dropped it from my hand to the floor twice and dropped it from the car holder to the console in my vehicle so many times I can't count.
The only problem I have is with the SMS freeze, and I've solved 90% of that by keeping my inbox clean. If I have the money for a class 6 microSD card, I'd bet on having solved the other 10% of my problems.
Since upgrading my radio, I don't have any problems with dropped calls, missing texts, loss of 3G or any of the other popular issues that seem to be plaguing the new owners.
Since bad news always travels faster and wider than good news, one simply can't infer from the issues being discussed here that they are the norm. I would suspect a very small percentage of the HD2 owners frequent the forums here, and of those another small percentage are having hardware issues.
I've been through a few of these new phone releases here in the past and from my experience I would say that this is pretty normal for the first few months of a phone's release. In another month or so there will be a firmware upgrade to fix the freezing and icon switching, then a lot of the issues will switch from hardware to software. Soon after that, I expect everyone will be clamoring for the release of a Windows Phone 7 ROM, followed a few months later by a newer, faster phone that everyone will be switching to. A cycle, vicious but almost predictable.

Loose feeling buttons on the HD2 (Does your phone have this too?)

On the front of the HD2, on the panel for the buttons, the panel is well how do I say this, loose. Not to the point where its faulty, but enough to annoy me. I went today and returned my HD2 for a new one which still had this problem. Really its just a small movement but i was wondering if all devices are like this.
Waiting for your reply's,
Regards, Shatterv2.
Sorry mine are fine !
Wondering if the T-Mobile man will be mad if i go back tomorrow, after i just returned it
my buttons are 'loose' too
shak7i said:
my buttons are 'loose' too
Click to expand...
Click to collapse
In a serious tone, er?
yeah mine are quite loose alo, but im tempted to throw mine at the wall soon and claim on my insurance lol
Hehe
I'm wondering if this is annoying enough to actually make me go back tomorrow.
Mine are loose too, have been since day one. Volume buttons feel flimsy too.
conantroutman said:
Mine are loose too, have been since day one. Volume buttons feel flimsy too.
Click to expand...
Click to collapse
The reason why I began this thread was mainly to see If it's worth it to go back, UN-HSPL2 my phone again repack it all and return it for a new one. Seeing as others have the same problems I may not
I think its the case with a lot of phones.......
mine havent got any looser in the 7 months I've had it, its only around 1mm worth of movement, if that puts your mind at rest any.........
conantroutman said:
I think its the case with a lot of phones.......
mine havent got any looser in the 7 months I've had it, its only around 1mm worth of movement, if that puts your mind at rest any.........
Click to expand...
Click to collapse
Dosent hurt . Better than my old HD2 where the panel actually squeaked on the back button. Things like this that make me envy the buttons on the EVO and the Nexus. Damn you HTC
My front panel buttons don't even budge. Same for my volume button.
Weird?
Seems like some devices were damaged during shipping or something. I guess it bugs me to have a device worth 500-600 dollars and then have a loose panel on the front. Ill give it a week and i might go back to T-Mobile and make sure i get a good one
I thought that is how the buttons were. It's one long piece of plastic inserted between the glass screen. It can't be metal cause it might scratch the sides or something. The buttons on my HD2 has a small wiggle to it, but I've never seen anything otherwise. (with those type of buttons)
The HD2 is a quality device. After checking the volume buttons and the quality of the case, it just seems to me that that's the best those buttons can be at this time period. What do you guys think?
Month and a half of use - all are very tight/firm. Do get from time to time a little sticking noise on the power button but that seems to be fading. They should have been individual buttons instead of the single strip and have mechanical keys that were made of metal. Mine is the US version TMobile. Very solid phone. No complains so far and compared to my previous phones - TYTN I / TYTN II, Fuze this one seems to be built the best. No flex - super solid. The only thing that seems to be better built is the iPhone. Their latest version 4 seems super solid although I'd never buy it.
The buttons on my device are a bit loose too. Not when you simply press it but when you actually try to move them a bit. Anyway I can't be more descriptive LoL.
Nothing very annoying, I guess it's like the other poster said, a bit of plastic inserted between the screen. I had my doubts when I first got it (given that my Rhodium's buttons couldn't been more tight), but I can live with that. Like I said, not very irritating. The volume buttons though are very tight!

[CLOSED] Loose hinge? Still an issue?

There is already an active thread discussing the hinge issue. Please direct further discussion here. PS, you are lucky I did not just delete this entirely! ~TheRomMistress
Hey guys,
For those who own htc desire z, hows the hinge for you already? How long have you owned the device already?
Other than that, hows the speed performance for you guys? In terms of web browsing and opening applications?
Thanks for your time.
Sent from my HTC Desire
Speed for me is awesome, and I'm still at stock speed, not tried overclocking yet.
My hinge is fine, just the same as when I initially got the phone (about two and a half weeks ago).
Unless your phone is faulty, I think the only people who have a problem are some who want to use their phone while lying in bed and holding the phone right above them. I never use my phone like that.
steviewevie said:
I think the only people who have a problem are some who want to use their phone while lying in bed and holding the phone right above them. I never use my phone like that.
Click to expand...
Click to collapse
I do use it like this, every night, and no problem at all. The design is not faulty. When you hold it like that above your face whilst in bed the way the hand and fingers hold the device the screen stays open and does not fall down at all.
Every night I use it like this!
ayewhy said:
I do use it like this, every night, and no problem at all. The design is not faulty. When you hold it like that above your face whilst in bed the way the hand and fingers hold the device the screen stays open and does not fall down at all.
Click to expand...
Click to collapse
I know what you mean. I did actually try and the way I would hold the phone in that position it won't open for me either. Seems there are a few who hold their phone differently when laying down though, and then perhaps gravity means it does open.
steviewevie said:
...I think the only people who have a problem are some who want to use their phone while lying in bed and holding the phone right above them. I never use my phone like that.
Click to expand...
Click to collapse
Not strictly true. My hinge is fine - had the phone 9 days now and it's still as tight as it started out. My only problem is that the top half of the phone is not tight against the bottom half when it's closed - causing a tapping when using the touchscreen. I'm ok when I have a gel case on it which keeps the two halves separate and cushioned. Only problem is that this case makes it difficult to type on the top row of keys. I have another hard case which is thinner, but does not eliminate the tapping problem. I'm waiting for another case to arrive from the US which is rubber - hopefully will cushion like the gel, but be thin like the hard case.
I opted not change the phone since I have been told others have the same problem, and I didn't want to risk getting a loose hinge AS WELL AS the tapping...
At the end of the day this phone is pretty effing awesome otherwise (aside from a few little software issues - which will be fixed by devs on XDA no doubt), and I'm sure I will solve this problem one way or another, whether it's with a particular case, or worst comes to worst, sticking some of sort of thin cushioning material to the bottom of the top half of the phone - any suggestions, please feel free to let me know!!
I do wish HTC had just gone with a normal slider though, and this phone would be perfect.
My DZ is exactly as setspeed described..
I would add that while holding the DZ without the case mentioned by setspeed, it feels a bit like holding two thin phones combined together rather than one phone.
its really not as bad as it sounds but i would have liked it if there was some sort of latch or something to hold the screen tight to the keyboard while the device is closed.
I have the phone for two weeks now.. for the first couple of days I put a rubber case on it (the black case that T-Mobile sell for the G2) but i removed it very quickly as i felt it gave the phone a very bulky feeling to it.. the case is not very thin and the DZ is not the lightest of phones.
Im on the lookout for a thinner case too.. it would be great if there was a clear one as-well..
setspeed, please post your thoughts on the new case after you try it out
I also thought of adding some cushioning material to the bottom of the screen, I'm on the lookout for that as-well..
other than that, my hinge holds the screen tight in place while the device is open.. the screen opening while the phone is upside down is really not an issue.
I haven't rooted my phone yet, i don't really feel the need to.. I compared it to the old desire i bought for my girlfriend.
I think that the new Sense UI is a bit heavier on the system and so there are some places i feel the old desire is faster.
for example, when dragging down the notification view from the top of the screen, the new Sense gives you a list of recent apps used. sometimes it needs to populate that list and so dragging down the notification view is not as fluent as on the old desire. its not an issue because once it populates the list, it runs smooth very smooth as-well.
I think there is also a bit of lag while scrolling through menus. the lag clears after first scroll and then it runs smoothly again.
I'm sure that there are some optimized roms out there that take care of those small issues.
I had a hard time deciding which phone to buy - the old desire or the Z..
I'm actually really happy with my decision..
Its a very very good phone
Hope you found my thoughts useful

Bad build on my Atrix?

It looks like the bottom right of my phone has an issue where the front and side parts do not meet up, and so I get some light bleed on that edge. Does anyone else have this issue, or is it just mine and should I get it replaced?
I would find out if its a problem specifically to your phone or all of them.If its just yours get it swapped out.
That would be just yours... I dont have that issue
dont have any problems like that. swap it for a new one.
I just checked mine and looked very hard to see if any light leaked and it doesn't seem to. I'd definitely say that's not normal/how it's intended to be... not sure how common it is.
Does the gap seem noticeable? Aside from the light that is. Does the "frame" around the glass seem bent? My glass seems to fit the frame completely, so I can only imagine that happening if the frame was bent somehow or if the glass was not made properly.
If the gap is significant enough to let crap get in there, then it might be worth returning. If it's just a little light, it's a tougher call. Based on the pictures, I'd like to say I wouldn't bother. That said, I get the feeling I'd probably get it replaced if it were actually my phone. The biggest thing is if you can see any other potential problems as a result of whatever the issue is.
Same as above, I don't have that issue.
Thanks everyone -- I'll take it back tomorrow and see what they say - probably will get a replacement just to be on the safe side.
CC Lemon said:
I just checked mine and looked very hard to see if any light leaked and it doesn't seem to. I'd definitely say that's not normal/how it's intended to be... not sure how common it is.
Does the gap seem noticeable? Aside from the light that is. Does the "frame" around the glass seem bent? My glass seems to fit the frame completely, so I can only imagine that happening if the frame was bent somehow or if the glass was not made properly.
If the gap is significant enough to let crap get in there, then it might be worth returning. If it's just a little light, it's a tougher call. Based on the pictures, I'd like to say I wouldn't bother. That said, I get the feeling I'd probably get it replaced if it were actually my phone. The biggest thing is if you can see any other potential problems as a result of whatever the issue is.
Click to expand...
Click to collapse
the only time that you can really tell is in the dark (how I saw it in the first place this morning when I got up and grabbed my phone) -- otherwise even looking directly at it it's not noticeable. I'm just wondering if the store did something to it (very long story, but they hosed up and ordered me the wrong stuff and magically found this one to give me so I'm wondering if it was a return that I got or something odd).

Home button durability.. lets talk..

So, like many, i have jumped on the S6 bandwagon, and am rather enjoying it so far (so much so that i haven't even bothered with bootloader or root yet). And while over the few days so far the glass is great (i would hope so.. sheesh), i have noticed some scratches already on the home button. Now, being that no phone will ever stay perfect, i accept that wear and tear will happen, but i was surprised to see it this early.
Certainly, i am happy enough with the phone (non scratched glass, good battery life (with bloat disabled), etc), but am curious to see if i am alone in this, or others have the same issue.
And more to that - will the scratches become a problem for the fingerprint reader (something i do enjoy using, and would like to keep doing so)? Perhaps some voices of experience can bring some wizdom..
Divine_Madcat said:
So, like many, i have jumped on the S6 bandwagon, and am rather enjoying it so far (so much so that i haven't even bothered with bootloader or root yet). And while over the few days so far the glass is great (i would hope so.. sheesh), i have noticed some scratches already on the home button. Now, being that no phone will ever stay perfect, i accept that wear and tear will happen, but i was surprised to see it this early.
Certainly, i am happy enough with the phone (non scratched glass, good battery life (with bloat disabled), etc), but am curious to see if i am alone in this, or others have the same issue.
And more to that - will the scratches become a problem for the fingerprint reader (something i do enjoy using, and would like to keep doing so)? Perhaps some voices of experience can bring some wizdom..
Click to expand...
Click to collapse
Mine had scratches right out of the box and I scratched it further thinking there is a protective film over it since it looked like it had one. Its definitely a concern in the long run though I was able to get rid of the scratches by using toothpaste. My home button also wobbles a bit vertically and if I tap it gently in the left corner, it creates a clicky noise. The biggest concern for me right now is the pink tint on my s6's screen on the bottom half and left side. I can exchange but may end up getting the same/worse unit since most of the people who faced this issue ended up getting worse/similar units.
Will the finger print scanner stop working after many scratches is something we can only guess at the moment.
What's it made of?
The home button had the same vulnerability on the Note 4 and Note Edge, but it never affected the fingerprint reader. Micro scratches galore, but nothing too glaring and didn't affect the functionality.
Well, i certainly will agree right now, what i see is micro, and has had no impact on the scanning (4 fingers registered, no issue at all). I am a little disappointed that with the excellent build otherwise exhibited, something people will use most may be the most prone to scratches; but i also accept that that sensor may not work with more durable materials.
Still, a little more reassuring that the Note 4 is similar and should be ok..
I've noticed some minor scratches too on my home button. I'm not sure whether they were there out of the box as I didn't think to look closely at the time.
I imagine you could take a cheap plastic/PET type screen protector and cut out an oval shape and put it on the button. I'm not sure whether that would change the fingerprint recognition or not since I don't know how those scanners work. It would be easy to test though even before trying to cut the shape out.
Divine_Madcat said:
So, like many, i have jumped on the S6 bandwagon, and am rather enjoying it so far (so much so that i haven't even bothered with bootloader or root yet). And while over the few days so far the glass is great (i would hope so.. sheesh), i have noticed some scratches already on the home button. Now, being that no phone will ever stay perfect, i accept that wear and tear will happen, but i was surprised to see it this early.
Certainly, i am happy enough with the phone (non scratched glass, good battery life (with bloat disabled), etc), but am curious to see if i am alone in this, or others have the same issue.
And more to that - will the scratches become a problem for the fingerprint reader (something i do enjoy using, and would like to keep doing so)? Perhaps some voices of experience can bring some wizdom..
Click to expand...
Click to collapse
any chance the micro scratches were there out of the box? i've had mine since April 1st and don't see any scratches...yet.
mrvirginia said:
any chance the micro scratches were there out of the box? i've had mine since April 1st and don't see any scratches...yet.
Click to expand...
Click to collapse
Actually, yes, it is quite possible, as i noted them just about the second day i had it, and was shocked to see them. I may not have the smoothest thumbs, but the scratches went all the way across, which is also odd.
So far, no real issues, but it was surprising to see (part of me wrongly assumed the button was also glass).
Divine_Madcat said:
Actually, yes, it is quite possible, as i noted them just about the second day i had it, and was shocked to see them. I may not have the smoothest thumbs, but the scratches went all the way across, which is also odd.
So far, no real issues, but it was surprising to see (part of me wrongly assumed the button was also glass).
Click to expand...
Click to collapse
honestly it should be glass. guess they're still working on premium quality 100%
it may be more likely that they were there out of box. i've tried scratching mine with my nail and no dice.
they have some assembly line and packing kinks to work out clearly. my device thankfully came unscathed but the plastic wrap that covered the phone looked like someone had pulled it back on with their finger/nail - there were 3 little indentions on it.
So, i hope its not related, but i have had my phone now fail to read my fingerprint a few times, and pop up a notice saying there was a failure, and if it keeps happening, reboot the phone. A reboot (or even manual unlock) seems to work, but i am hoping its not a sign of things to come...
No micro-scratches here yet....
I've confessions to make: I'm obsessed with physical buttons wearing off! The first app I installed is "pie control", which is something I really got accustomed to and find more practical than using home button and recent button, incidentally this saves a lot of click on the home button. I've been using for a while even an accessibility feature that let you wake up the phone by waving in front of it, to be honest I don't use much this one. Then again I use Nova Launcher and I set up a shortcut to lock the phone double tapping the display. I know I'm way overcaring about this, on the other hand I just dismissed my old S3 that was still practically perfect even after almost 3 years of usage.
Divine_Madcat said:
So, i hope its not related, but i have had my phone now fail to read my fingerprint a few times, and pop up a notice saying there was a failure, and if it keeps happening, reboot the phone. A reboot (or even manual unlock) seems to work, but i am hoping its not a sign of things to come...
Click to expand...
Click to collapse
Let me recommend you something what I personally did after finding micro scratches right out of the box. Use an ear bud (used to clean ear) and a very small amount of toothpaste. Apply a little paste on the bud and gently rub the home button for a min or so. Once done, wipe it from a damp cloth and also taking out bits an pieces of the paste that may have got around the gaps.
I was completely able to remove micro scratches doing the above and hope it helps you too. People have also used the above method to clean their camera lenses with great effect. Look out for a thread under the Xperia Z3 compact page where people complaint of having scratches on their camera lens after using the phone for a while.
Note - Dont rub too hard on the home button. It wont harm but will take away the gloss from the button leaving it looking matte.
CafeKampuchia said:
What's it made of?
Click to expand...
Click to collapse
The button is actually metal, but the substrate for the sensor (on top) is of a type of polymer film- like plastic? I'll post a source link when I get a chance. Thx
See link:
It's definitely not durable
https://techpolarity.wordpress.com
I'll give it a try tonight the toothpaste and the q-tips .... hope it works... i'll try to be as gentle as possible and go up from there ... thanks for the info man. Same problem here. Came, I believe scratched from the box, had a scratch on it from the first day and it went up from there. Dunno what is wrong with samsung they always have to screw up somehow.
Hawkeye1103 said:
I'll give it a try tonight the toothpaste and the q-tips .... hope it works... i'll try to be as gentle as possible and go up from there ... thanks for the info man. Same problem here. Came, I believe scratched from the box, had a scratch on it from the first day and it went up from there. Dunno what is wrong with samsung they always have to screw up somehow.
Click to expand...
Click to collapse
Yeah... I do believe they messed up this time.
https://techpolarity.wordpress.com
They decided to use a non-durable substrate. The above article explains why. Good luck!
Lucidd33 said:
Yeah... I do believe they messed up this time.
https://techpolarity.wordpress.com
They decided to use a non-durable substrate. The above article explains why. Good luck!
Click to expand...
Click to collapse
This is just conjecture. While it may very well be true, the author doesn't give any evidence or references to back this claim. For all we know, Samsung may have chosen plastic simply because it was cheaper.
when the iPhone 5S was launched, a few people expressed concerns that the sort of CMOS scanner they were using tends to deteriorate over time. This, thankfully, hasn't proven to be the case; however I think that this deterioration is mitigated by an exceptionally strong sapphire glass coating on the 5S's home button - and now on the 6 and 6 Plus.
I have concerns for the durability of the S6 home button too - not for the scratches (which mine also exhibited after only 6 days of careful use), but for the likelihood of the sensor itself wearing out over time, as they are supposedly prone to doing. If Samsung have indeed skimped on the protection this home button requires for long-term durability then people will be in for a nasty shock further down the line when they can no longer use the fingerprint recognition, or when it deteriorates to the point of being useless. For those who recommend using toothpaste to clean the scratches out, I would suggest that this is a terrible idea - clearly scratches are going to reappear anyway, and taking some of the already weedy protection away from the fingerprint scanner with a micro abrasive surely can't be a good idea.
I'm really happy with the S6 but the home button is a big concern for me. I simply don't think it's as high quality as the ones Apple use. My 6 day old S6 has been exchanged by the store for a new device as the home button not only rattled but didn't work at all on the left side unless it was pressed with a degree of weight. My replacement still jiggles a tiny but but is at least better.
To me this is a bigger issue than 'Sensorgate', which is just a load of rubbish as far as I'm concerned.
leoni1980 said:
when the iPhone 5S was launched, a few people expressed concerns that the sort of CMOS scanner they were using tends to deteriorate over time. This, thankfully, hasn't proven to be the case; however I think that this deterioration is mitigated by an exceptionally strong sapphire glass coating on the 5S's home button - and now on the 6 and 6 Plus.
I have concerns for the durability of the S6 home button too - not for the scratches (which mine also exhibited after only 6 days of careful use), but for the likelihood of the sensor itself wearing out over time, as they are supposedly prone to doing. If Samsung have indeed skimped on the protection this home button requires for long-term durability then people will be in for a nasty shock further down the line when they can no longer use the fingerprint recognition, or when it deteriorates to the point of being useless. For those who recommend using toothpaste to clean the scratches out, I would suggest that this is a terrible idea - clearly scratches are going to reappear anyway, and taking some of the already weedy protection away from the fingerprint scanner with a micro abrasive surely can't be a good idea.
I'm really happy with the S6 but the home button is a big concern for me. I simply don't think it's as high quality as the ones Apple use. My 6 day old S6 has been exchanged by the store for a new device as the home button not only rattled but didn't work at all on the left side unless it was pressed with a degree of weight. My replacement still jiggles a tiny but but is at least better.
To me this is a bigger issue than 'Sensorgate', which is just a load of rubbish as far as I'm concerned.
Click to expand...
Click to collapse
You do make some really good points… When you returned your phone for exchange, was it a big pain in the ass? Did they hint that they do an exception for you?
I've just become very wary about returns, exchanges because I've been screwed before on exchanges and being stuck with a mediocre device.
Anyways, I am very surprised that not too many complaints about the sensor has come up on the web searches so far.
I could demonstrate that the home button wouldn't work on the left side unless I pressed it hard. They were able to replicate it themselves so it wasn't too much of an issue. I struggle to deal with high street stores in matters of poor quality control though as they tend to take the stance of 'I can't see anything...it's not really an issue to me'. One thing I miss when I move away from Apple products - not to sound like a fanboy - is that I feel I can trust that they will rectify any little annoyances I have.
One thing I feel confident in saying with absolute certainty is that the home button on the Galaxy S6 is not even close to the quality of Touch ID. It works, and it works well; but the feel it gives when you click it, the overall travel and the cheap plastic feel is a giveaway. Samsung are nearly up to iPhone standards with this device in terms of quality control but this button is its Achilles heel - they kind of cheaped out.

Categories

Resources