Related
Hi there,
unfortunately I dropped my Toch HD last weekend on rough ground, the housing ist completely scratched at the corners and looks awful. The lucky part is that technically it still works perfectly and the display/screen is not damaged.
So, I'd like to replace the housing and I've already found some replacement parts on the net (e.g. here for USD 80... i know, quite expensive but for me it's worth it, cheaper offers always welcome though).
The real problem is that I couldn't find any instructions to do it and no hints whether any special tools are necessary. The forum search only delivered rare information. With a proper instruction I would dare to do it myself, but without I'm afraid to damage the device.
So has anybody got a detailed instruction or experience changing the housing?
would be grat,
thanks in advance,
regards jan
Isn't this what you are looking for?
http://htcdriver.com/index.php?page=htc-blackstone-touch-hd-service-manual
And congratulations for not damaging the screen, because this is what happened to me (see the attachment), and amazingly everything works .
Thank You, exactly what I was looking for...
...however, it looks much more complicated than I expected... have to toke some time to analyze the instruction for which steps are necessary for changing the casing only without complete disassembly... not sure yet if I should dare it...
but, anyway, thank you again!
regards jan
P.S.1: has anybody tried it yet and have some experience to share?
P.S.2: I'm not sure about the "plastic stick" shown in the disassembly part... whether it's really just a flat and bit flexible plastic stick or if itr has any special tip...
try, it's easy
I did it on a P3600 and it was not so difficult, just take your time (at least one hour).
Read everything carrefully before starting, prepare tools and clean your hands
I also dropped my touch hd and dented the front bezel. I have bought a complete replacement housing and tools required for only £25 on ebay.
I have read the service manual and it doesn't deal with removing the lcd screen from the bezel. I read somewhere that it is a complete unit and you can't detach it easily
The new case is still in its box until I can find more out. Any ideas would be greatly appreciated!
Yup it isn't as easy as it looks. The manual lacks details as it only tells you how and where but did not elaborate more on minor yet important details.
I bought an antenna cover from ebay to replace, and boy, removing the cover was not easy at all. I used to take apart my other phones all the time and HD is the most difficult one I've done. I ended up breaking the small plastic sockets (that clicks the cover firmly into place) of the original cover. Luckily I have a new one to fit back in. Originally I wanted to replace the whole housing myself but I stopped after the antenna cover until I get a video of how its done.
So anyone? Kindly? Any videos please? XD
still no videos out there?
not looking good for us as i still can't find any video tutorials out there so im assuming that its super hard to do
please can anyone assist?
superseagull said:
not looking good for us as i still can't find any video tutorials out there so im assuming that its super hard to do
please can anyone assist?
Click to expand...
Click to collapse
lol i chickened out eventually. and im still using my not-so-perfect housing as im reluctant to change it myself while being too stingy to pay a pro to do it.
Hi everyone,, wondering if some one could provide me with some assistance. I bought a full replacement housing for my sony x10 as the phone got a huge gash in the side which was really insightly so the best thing was to replace the entire housing.
Quick question, the digitizer. It seems like its completely glued on to the housing? do i need to replace the digitizer if im replacing the housing as well? do i need to use glue and redo it? not sure if i take it off can it break easily... any information would be greatly appreciated.
Simply check my Disassembly Guide.
You'll find it in my Sig.
There is everything described.
If you have any questions, feel free to ask them over there.
@Mods: Please close this one...
*** Updated and added new pictures on this post and post no3. ****
Since I could not find anything on the web about disassembly, I jumped in head first and it came apart pretty easy. The biggest mystery was trying to take the LCD housing apart because there were no screws showing. But after some investigation I noticed there is a textured tape like covering on the ends of the bottom part of the LCD housing, which is covering 4 screws! The replacement of the digitizer was pretty simple because its only attached to the housing not the display (LCD)! So this removes the worry about breaking the lcd display. I did pull a 4pin connector for the side volume control off the board ,while trying to disconnect it, so I having a tricky soldering job ahead of me.
Update: I forgot to mention about using a hair dryer to loosen the glue that holds the digitizer to the housing, this makes a much easier job of removal. Thanks: jetcitydevices, see his post http://forum.xda-developers.com/showpost.php?p=7983391&postcount=41 for more details
There's really no reason for this to be in its own thread, considering you already started one thread on this same topic...you could've just continued the conversation in that thread since it IS about the exact same thing....no need for duplicate posts, plus posting duplicate threads is against the rules. Please read the stickies if you are unsure of forum rules on posting....
Please also report this thread to the mods to be deleted, then carry on your convo in your original thread...thanks!
-BMFC
Sent from my ROOTED myTouch3G Slide
More picture of lcd housing disassembly.
This is great I have been searching for a disassembly thanks hope to see more pics soon
Sent from my T-Mobile myTouch 3G Slide using XDA App
I will have some more pictures with some notes soon.
Great job! Hopefully I never have to open mine up, but if I do, I'll use this as a guide.
Sent from my T-Mobile myTouch 3G Slide using XDA App
Can you give us some close-ups of each section?
Thanks
yeah man, give it your best. so far, this is the ONLY MTS disassembly online, PERIOD! add steps and pics plus some close ups. would be nice to have as a bookmarked reference guide.
oh btw, be careful with the lcd if you wanna go that far. they can (and will be!) be a *****. all the ribbon wires plus the sealant on the glass is extremely fragile.
wow, good thing i found this....this is the only one i found. did u buy the digitizer off ebay? i need to do the lcd also....
Yep I got it from a ebay store called gadgetfix and they have great customer service if you have a problem.
Also I have updated one of the pictures in the first post with info about removing the 4 pin ribben cable.
That's the only one I found on ebay. Did it come with tools?
Ya that's the same one in ebay I found....did it come with tools?
mulletcutter said:
Ya that's the same one in ebay I found....did it come with tools?
Click to expand...
Click to collapse
No tools were included, but all you pretty much need is jewelers screwdriver set and torx but i think the jewelers might even work for the torx screws too.
mmone3 said:
No tools were included, but all you pretty much need is jewelers screwdriver set and torx but i think the jewelers might even work for the torx screws too.
Click to expand...
Click to collapse
Then that guy lied, he said tools are included. I have to get a new lcd also, is there anything to swap over or is it just plug and play
My sim card slot is broken, could i replace it with the one in my G1?(Sim cant be read)
mulletcutter said:
Then that guy lied, he said tools are included. I have to get a new lcd also, is there anything to swap over or is it just plug and play
Click to expand...
Click to collapse
The lcd should be plug and play, looks like its just connected to the top and bottom boards.
Ace42 said:
My sim card slot is broken, could i replace it with the one in my G1?(Sim cant be read)
Click to expand...
Click to collapse
Sorry I cant help with the sim card problem, i have never had a g1.
Ace42 said:
My sim card slot is broken, could i replace it with the one in my G1?(Sim cant be read)
Click to expand...
Click to collapse
you should definitely warranty it
Phone screen compatibility question
I have been searching for screens of the same size as the slides screen but with I higher pixel density and I found that samsung makes a phone "Samsung Armani B7620" that has a 3.5 in screen. I was woundering if there was a way we could take that screen and use it with the slide.
Sent from my T-Mobile myTouch 3G Slide using XDA App
Hey mmone3,
Good job! Looks good! Keep it up... I would suggest just going to your local hardware store and buying a torx screwdriver. Thats all you really need... there is a plasic tool us cell techs use. Its basically a plasic flathead screwdriver and could be replaced with a guitar pick and also a metal awl which can be replaced with an ice pick. Those are for prying snapped-in plastic housing. And yeah... I told you the lcd is pain! Lol... I havent taken apart the mts yet but have opened hundreds of phones. They can be tricky but it helps if your a tech and can reach on your store shelf and pick up a front lcd housing or a ribbon if you break one by mistake
Just ordered my digitizer/lcd screen....hopeful I won't break anything taking it apart. You should make a video
A prelude...
Right, the other day I dropped my DHD onto some concrete from about 2 meters... Predictably the glass digitizer shattered!
However, I have no insurance (because I'm an idiot) and HTC quoted a repair cost of £85. Yes, £85. So I hit ebay and bought a digitizer, and decided to do the job myself!
Before I start:
1) THIS WILL VOID YOUR WARRANTY
2) I am not responsible if you do anything wrong, or even if you do everything right and it still goes wrong, or if your girlfriend leaves you, or if your dog dies, or if... You get the point
Part 1: Preparation
What you will need:
Your hands
A little brute force
1) Turn your DHD off!
2) Remove battery door and battery.
3) Remove sim card cover and take out sim card + SD card.
Done! That was definately the easy part...
Part 2: Taking off the unibody cover
What you will need
A torx 5 and torx 6 (T5, T6) screwdriver (or a very small flathead)
A small flathead screwdriver
LOTS of brute force
Some brain cells
1) Remove the LED flash cover. To be honest im not sure if their is a way this is meant to be done properly, but I used a flathead screwdriver (a VERY small one) to force it out from the top. This of course risks damaging the unibody cover but I really cant see a better way of doing it! (Turns out there is a better way of doing it, but you need an 'opening tool.' Cool).
2) Undo the 5 T6 screws holding the unibody to the device, they are labelled in the picture below in purple:
If you dont undo the screw underneath the LED flash cover and try to pull the unibody off, you end up with this:
Yes, I am that stupid.
(Still works though!)
I actually used a small flathead screwdriver to undo the T6 screws, but this risks ruining the screw itself. Also, the screws are tiny so make sure you keep them safe!
3) Remove the volume strip, its just a piece of plastic that covers the buttons inside, pinch it and then gently pull it upwards. It is quite delicate so be careful!
4) Slide the unibody case off. This isnt as easy as it sounds, it involves some brute force and some shimmying around... Be careful though! When I did this I think I damaged the LED at the top that flashed when you are low on battery. To be honest I found it extremely irritating anyway so I'm quite glad...
Part 3: errr...
Ok, I must admit I haven't actually got any further yet, I'm in the process of peeling away the old glass digitzer. When the new one arrives on wednesday I will complete this guide, but in the meantime here is a picture of the beasts' insides! If you have any requests for anymore pictures please don't hesitate to ask:
Poor thing
man, i think you should remove "desire hd" from your signature! =o)
i just want to know a little more about power button and volume button, since i think i will need to change it someday! =oP
thiagodark said:
man, i think you should remove "desire hd" from your signature! =o)
i just want to know a little more about power button and volume button, since i think i will need to change it someday! =oP
Click to expand...
Click to collapse
Sure!
Power button:
It's the small grey square thing, the rest of it is attached quite nicely to the unibody!
Volume button/thing:
Looks quite flimsy the actual bit of plastic itself that comes off can be bought on ebay though!
Nice
Thanks for this but a fix guide from the manufacturer would have been great...
For peeling away old digitizer, put your DHD for 5min in oven previously heated to 60°C .
One guy do it with HTC Desire and it works. There is actually full guide from this guy how to change digitizer on HTC Desire (not DHD) but guide is in latvian and Google translate is not very accurate, so it will not help you But idea with oven heated to 60°C is usable.
And dont overheat it
I found a disassembly video on youtube.
Enjoy: http://www.youtube.com/watch?v=JfatoeWbMRk:D
thanks! Now I know how to open my phone when i want to mod it.
Robi-K said:
I found a disassembly video on youtube.
Enjoy: http://www.youtube.com/watch?v=JfatoeWbMRk:D
Click to expand...
Click to collapse
Good video... But that voice is the most irritating thing I have ever heard in my life!
any progress?
wao....who on earth will want to disassemble?
aivarss said:
For peeling away old digitizer, put your DHD for 5min in oven previously heated to 60°C .
One guy do it with HTC Desire and it works. There is actually full guide from this guy how to change digitizer on HTC Desire (not DHD) but guide is in latvian and Google translate is not very accurate, so it will not help you But idea with oven heated to 60°C is usable.
And dont overheat it
Click to expand...
Click to collapse
I Can help to translate from Latvian to English just give me the link of that guide.
Sent from my Desire HD using XDA Premium App
thiagodark said:
any progress?
Click to expand...
Click to collapse
The reason I havent progressed any further is that I dropped the damn thing again whilst it was in pieces so its completely wrecked...
Open circuit board + wooden bedroom floor = £500 down the drain!
If anyone wants me to finish the guide I can, I got as far as getting the LCD off.
Keep Going
If its toast then please keep going, anything your able to document will help the next one of us that ends up having to take our phone apart.
Yours may be dead but you can help save others!
cool guide ))
now i know
Hey everyone my HTC HD2 got the Non-Responsive screen problem a week ago, & did a lot of research and found out that it was most likely a hardware problem with a cable..... So a lot of people would tell the people with the problem that the "Touch Screen Digitizer" is dead (like the cable), or it needs to be cleaned... pretty well go out and buy a new one... BUT I have never found evidence that someone has done this and it has successfully "cured" their HTC HD2 Non-Responsive touch screen problem...
So I was looking for anyone on the forums that could confirm this is a solution or give me any tips on what I should do.... AND no I don't have enough money to get a new phone, nor do I live in the USA so I can't send it in to fix it...
This is what I was going to buy for it:
http://www.ebay.ca/itm/NEW-OEM-HTC-...781?pt=LH_DefaultDomain_0&hash=item519a3d2e45
Thanks for taking the time to read my Thread, its much appreciated!! I hope I can find a fix!!
PS: If anyone wanted to know what it looks like out of curiosity I posted 3 pictures with RED circle HIGHLIGHTING the problem when I try to touch something....
My digitizer has been a bit dodgy for the past few months. It's ironic that when I finally found out what the issue was and called HTC, my factory warranty had ended exactly 4 days prior to the call.
Fast forward 3 months and my phone has now been unresponsive for 3 hours despite my prying and tweaking various hard parts.
I disassembled the phone down to the main board just to see how hard the install is, but it's a bit intimidating once it's time to start pulling all the film and ribbons. A bit too tight and small parts for my liking.
Time to hit CL to see if I can find a cheap replacement.
Good luck with your repairs. I may be following in your footsteps if I can not find a good deal.
Yeah I will see how well it goes... if anyone has useful info, i will be more than grad to hear it
Thanks
Many people attempt to replace a digitizer, but I simply don't recommend it, we see enough of do-it-yourselvers who created problems in addition to the original ones.
What I do recommend, however, and I stated it on many threads already, is to get an LCD+DIGITIZER assembly. Simply because it is easier to fit. Not saying the overall fitting is easy, always depends on your overall skill, so ensure that you are familiar with the procedure BEFORE you begin. But you will save yourself a lot of trouble by getting the whole thing, as opposed to the digitizer only for the sake of a few bucks.
However, if anyone still feels intimidated by the whole thing, I am on the lookout for working main board. Advertised a few times in the marketplace with limited success. So if anyone smashed their baby and will be looking to replace, rather than repair - drop me a PM. I am in NZ. Will pay by Paypal.
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
cheeselump said:
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
Click to expand...
Click to collapse
How much did the set cost?
cheeselump said:
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
Click to expand...
Click to collapse
Thanks I will check it out, hopefully it won't be to hard and I hope I can repair it!! oh and could you post a link of the youtube & manual you used to replace your screen?? Thanks
Oh would anyone suggest then just calling HTC and sending it to them to repair?? or does that cost to much??
Thanks everyone for the help
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
GnatGoSplat said:
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
Click to expand...
Click to collapse
Yah I was looking at the video's and they were taking off EVERYTHING... it looks really hard to do.. I don't know whether I want to do it anymore.....
oh and are you talking about the digitizer itself or the LCD+digitizer for your method?
Thanks
Heronization said:
Yah I was looking at the video's and they were taking off EVERYTHING... it looks really hard to do.. I don't know whether I want to do it anymore.....
oh and are you talking about the digitizer itself or the LCD+digitizer for your method?
Thanks
Click to expand...
Click to collapse
Yep, there is absolutely no reason to take off everything like some people seem to think is necessary.
The way I'm talking about requires removing LCD+digitizer. In fact, I think you'll always have to remove both because the connector for the digitizer is under the LCD. Anyway, the way I did it, I went from removing the the phone insides from the rear housing straight to separating the LCD+digitizer assembly from the frame. No removal of any boards or flex cables. The only cable to be disconnected is the LCD+digitizer assembly one. Getting it disconnected and reconnected does require unplugging the front button flex and removing the screws for the bottom logic board to loosen it, but that's all.
GnatGoSplat said:
Yep, there is absolutely no reason to take off everything like some people seem to think is necessary.
The way I'm talking about requires removing LCD+digitizer. In fact, I think you'll always have to remove both because the connector for the digitizer is under the LCD. Anyway, the way I did it, I went from removing the the phone insides from the rear housing straight to separating the LCD+digitizer assembly from the frame. No removal of any boards or flex cables. The only cable to be disconnected is the LCD+digitizer assembly one. Getting it disconnected and reconnected does require unplugging the front button flex and removing the screws for the bottom logic board to loosen it, but that's all.
Click to expand...
Click to collapse
Wow that sounds pretty simple! and for you it all works perfectly now?? no calibration needed or problems?? Maybe I will try it after all..... but what screw drivers to I need to dissemble it?? the screws look different from normal..
Heronization said:
Wow that sounds pretty simple! and for you it all works perfectly now?? no calibration needed or problems?? Maybe I will try it after all..... but what screw drivers to I need to dissemble it?? the screws look different from normal..
Click to expand...
Click to collapse
Well, it's not that simple because simply getting the HD2 insides out of the rear housing is difficult if you've never done it before. I believe the screwdriver you need is a Torx T-5. Once you get the screws out, you will need a plastic opening tool to go between the digitizer and rear housing frame. They look like this:
http://www.ifixit.com/Tools/Plastic-Opening-Tools/IF145-000
I found it comes out much easier if I use the tool to make a gap along the top edge and then slide the entire end of a scrap credit card into that gap, then that makes the whole assembly easier to pry out along the sides with the tool. I know on one of the vids, the guy takes forever doing this part and I can understand why, but once I figured out sliding a credit card into the top gap as far as it would go, I was able to get it apart much easier.
I can't answer whether the phone will work properly, because I just ordered the new digitizer over the weekend and haven't put it back together. I did remove the LCD+digitizer assembly and then re-connected it and put it back, then powered on the phone just to make sure pulling the LCD didn't hurt it - it didn't, everything worked as well as it did before. I did manage to crack the digitizer more when I tried to get the insides out of the rear housing before I figured out the credit card trick, so fortunately I was not trying to save my digitizer as it was already cracked. If you are just wanting to try to clean or fiddle with the connection, then you're going to have to be a LOT more careful than I was because it was all too easy to crack the digitizer!
I'm guessing yours probably needs replacement though. I sent my HTC Surround in for a funny acting digitizer, and the digitizer was replaced.
Oh, and if I would have bought an LCD+digitizer pre-assembled unit, that would have been super easy to replace. However, I opted to save $50+ by buying just the digitizer. Not too sure how I'm going to prevent dust getting in it, and I've read thickness of the adhesive is critical. I may regret it later!
GnatGoSplat said:
Well, it's not that simple because simply getting the HD2 insides out of the rear housing is difficult if you've never done it before. I believe the screwdriver you need is a Torx T-5. Once you get the screws out, you will need a plastic opening tool to go between the digitizer and rear housing frame. They look like this:
http://www.ifixit.com/Tools/Plastic-Opening-Tools/IF145-000
I found it comes out much easier if I use the tool to make a gap along the top edge and then slide the entire end of a scrap credit card into that gap, then that makes the whole assembly easier to pry out along the sides with the tool. I know on one of the vids, the guy takes forever doing this part and I can understand why, but once I figured out sliding a credit card into the top gap as far as it would go, I was able to get it apart much easier.
I can't answer whether the phone will work properly, because I just ordered the new digitizer over the weekend and haven't put it back together. I did remove the LCD+digitizer assembly and then re-connected it and put it back, then powered on the phone just to make sure pulling the LCD didn't hurt it - it didn't, everything worked as well as it did before. I did manage to crack the digitizer more when I tried to get the insides out of the rear housing before I figured out the credit card trick, so fortunately I was not trying to save my digitizer as it was already cracked. If you are just wanting to try to clean or fiddle with the connection, then you're going to have to be a LOT more careful than I was because it was all too easy to crack the digitizer!
I'm guessing yours probably needs replacement though. I sent my HTC Surround in for a funny acting digitizer, and the digitizer was replaced.
Oh, and if I would have bought an LCD+digitizer pre-assembled unit, that would have been super easy to replace. However, I opted to save $50+ by buying just the digitizer. Not too sure how I'm going to prevent dust getting in it, and I've read thickness of the adhesive is critical. I may regret it later!
Click to expand...
Click to collapse
Ok thanks I think thats what I am going to do, first dissemble it then try to move the cable around because, just yesterday it started to work again and then today it isn't working. I will contact you if I have a problem or get stuck, if that is ok with you
Thanks a lot
Heronization said:
Ok thanks I think thats what I am going to do, first dissemble it then try to move the cable around because, just yesterday it started to work again and then today it isn't working. I will contact you if I have a problem or get stuck, if that is ok with you
Thanks a lot
Click to expand...
Click to collapse
Yeah, no prob. I can post a pic of the digitizer lifted from the frame which shows where the adhesive tapes are that you have to go through, if it would help.
GnatGoSplat said:
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
Click to expand...
Click to collapse
Hey lolz I need your help already, I just took off the back housing and now Im lost on what to do... It looks to me as if you do have to remove the cables from the motherboard to get to it?? and what is the double sided tape? and isn't everything connected to the lcd?? lolz this is my first time doing any phone disassemble.. Thanks
added a picture of what I was thinking of doing... or am I doing this all wrong... because you did say we don't need to remove any flex cable or wires and stuff
Thanks!!
Heronization said:
Hey lolz I need your help already, I just took off the back housing and now Im lost on what to do... It looks to me as if you do have to remove the cables from the motherboard to get to it?? and what is the double sided tape? and isn't everything connected to the lcd?? lolz this is my first time doing any phone disassemble.. Thanks
added a picture of what I was thinking of doing... or am I doing this all wrong... because you did say we don't need to remove any flex cable or wires and stuff
Thanks!!
Click to expand...
Click to collapse
Nope, I didn't disconnect anything except the circled connector on the far right of your picture. You will need to do that to remove the LCD flex cable from the logic board.
I've attached a pic of the LCD module loosened from the frame. What you do is use something thin and flat to separate the adhesive tape holding the LCD to the frame. You will need to lift some of that black fabric tape on the edge to see where the LCD module meets the frame. Near the top, you will probably have to slide your separating tool all the way through to separate the tape (I used a scrap credit card). Avoid the area where the LCD flex cable is, because you could damage it! It's on the lower right of the LCD if you are looking from the front. When the LCD is loose, lift up from left to right (when LCD is facing you), pretending that there is a hinge on the right side. This is because you don't want to put any force on the LCD flex.
Once you've got your phone looking like my picture, you can remove the "captain" (orange tape), unlatch the LCD flex from the top, remove the button flex from its connector, then loosen the bottom logic board from the frame just enough to pull the flex out of the connector.
I hope that makes sense! It probably helps to know that a very strong double-sided sticky tape is all that holds the LCD+digitizer assembly to the frame, and there is only one flex cable connecting LCD+digitizer assembly to the rest of the phone.
GnatGoSplat said:
Nope, I didn't disconnect anything except the circled connector on the far right of your picture. You will need to do that to remove the LCD flex cable from the logic board.
I've attached a pic of the LCD module loosened from the frame. What you do is use something thin and flat to separate the adhesive tape holding the LCD to the frame. You will need to lift some of that black fabric tape on the edge to see where the LCD module meets the frame. Near the top, you will probably have to slide your separating tool all the way through to separate the tape (I used a scrap credit card). Avoid the area where the LCD flex cable is, because you could damage it! It's on the lower right of the LCD if you are looking from the front. When the LCD is loose, lift up from left to right (when LCD is facing you), pretending that there is a hinge on the right side. This is because you don't want to put any force on the LCD flex.
Once you've got your phone looking like my picture, you can remove the "captain" (orange tape), unlatch the LCD flex from the top, remove the button flex from its connector, then loosen the bottom logic board from the frame just enough to pull the flex out of the connector.
I hope that makes sense! It probably helps to know that a very strong double-sided sticky tape is all that holds the LCD+digitizer assembly to the frame, and there is only one flex cable connecting LCD+digitizer assembly to the rest of the phone.
Click to expand...
Click to collapse
Awesome I will try it now, I do need to heat the screen some for the tape to get sticky so I can pry it off right?? and I am guessing once you have removed that tape you can't "just stick it back on together and it will work right?? right??
Heronization said:
Awesome I will try it now, I do need to heat the screen some for the tape to get sticky so I can pry it off right?? and I am guessing once you have removed that tape you can't "just stick it back on together and it will work right?? right??
Click to expand...
Click to collapse
You could try heating; I didn't, but maybe it will come apart easier if you do. In the HTC factory service video, they mentioned putting the whole phone into the oven to loosen the tape. I didn't know if it would be a good idea to do that complete with all the circuit boards or not.
No, without heat, the tape is definitely ruined and I will need to replace it. I was planning to use some leftover tape I have from fixing iPhone digitizers so I didn't even attempt to salvage the existing tape. Not sure if it's even possible to salvage that tape considering you need to stick some kind of tool in there to separate it.
GnatGoSplat said:
You could try heating; I didn't, but maybe it will come apart easier if you do. In the HTC factory service video, they mentioned putting the whole phone into the oven to loosen the tape. I didn't know if it would be a good idea to do that complete with all the circuit boards or not.
No, without heat, the tape is definitely ruined and I will need to replace it. I was planning to use some leftover tape I have from fixing iPhone digitizers so I didn't even attempt to salvage the existing tape. Not sure if it's even possible to salvage that tape considering you need to stick some kind of tool in there to separate it.
Click to expand...
Click to collapse
Alright thanks I have to go and don't know when I'll be back, but I will try it tonight and hopefully I don't break anything...
Thanks for the help!