Related
Does any else have a battery cover that creaks a bit when you put pressure near the top of the right side? I am sure its just due to the fact its plastic instead of metal, but its one of those little things that will bother the hell out of me if I am the only one who has this problem...
Mine seems totally fine, I just tried to get it to creak with no luck. Do you have a screen protector that it may be rubbing on?
I noticed it too. I guess as long as it doesn't slip off easily, it should be fine.
I haven't noticed this; however, in order to take the cover off for your SIM, battery, and sdcard; the right side of the phone is a pressure point (at least on my phone) to help free it from the clips holding it in place when you want to pull it up. Mine doesn't creak, but I do notice if I put some pressure on it there is a bit of give. HTH.
A little bit off topic but yesterday I rooted my girlfriends Aria and I automatically took the back cover off because I thought the procedure would be similar to my Incredible. After I was done with the root I left the back cover off and tried to make calls and send texts but nothing worked. I had no service until I put the cover back on. When I looked a little further it seemed like there were two contacts on the back cover that must serve some purpose. Is this true?
I was a little shook for a minute....Thought I ruined her phone!
The antenna is in the back cover...
Well there ya go....thanks.
Sent from my ADR6300 using XDA App
yea mines pretty solid no creaks
I have the same problem with mine. It's on the same side too. I got a case from the ATT store and its gone away. Makes the phone more sturdy for me
Sent from my HTC Liberty using XDA App
I have the same issue ,, but in the top left corner... it is really annoying...
Yep, top right corner creaking here
As many times as I've had the back cover off swapping between SD cards though it was only a matter of time.
Hey Guys i recently dropped my device into some water, no biggie device still worked and everything, but it was an excuse to get a device with slightly better Bin, so i filed a insurance replacement. So i figured i had already screwed it up, why not take it apart before sending it back.....
As with probably everyone we have all seen the IFIXIT tear-down of our device and they had some issues taking it apart, and even damaging the plastic bezel on the housing. So i was intimidated, but i wanted to see if it really was that hard.....
Guys its NOT HARD AT ALL....The hardest part is the plastic on the sides is actually pretty soft, but the only damage i had was before i heated the device up i tried trying to pry the speaker cover off with just a screwdriver (bad idea). This gave me some very very slight damage where i was prying against the plastic. With the heat and then pry this wont happen. (the adhesive is ridiculous by the way, some very strong stuff (I blame 3M)
Step 1: Heat up device with a hairdryer at the bottom speaker cover, your going to need to get it pretty hot (be careful, your speaker is under that)
Step 2: With device still nice and toasty take a spreader ( i used a guitar pick, but i was thinking a hot razor blade slid under might be more effective)
Step 3: Gently work spreader under speaker cover and work from one end to the other, I used a razor blade to get a gab and then work it off, wasn't to hard since the adhesive is warm and easy to peel off the cover. (be careful, you still have to use that adhesive to put it back on, or use another adhesive)
Step 4: Once bottom speaker cover is off take your spreader and place it between the black part of the housing and the silver part (essentially the phone is placed in a aluminum shell, and you need to get it out).
Step 5: With Spreader placed between the chases gently slide from one end to the other, on the right side by the speaker cover is a white tab, slowly leverage this tab separating the black housing from the silver housing, then pry up from one side to the other tell you get a decent gap.
Step 6: Take your separator and go a side of your phone, doesn't matter which one is done first, just like the previous step, place your spreader between the black housing from the silver, and gently slide from the bottom up, if your doing it right you will hear 3 clicks and that side is separated.
Step 7: Take your spreader and repeat Step 6 on the other side until you hear three clicks.
Step 8: Take spreader back to the bottom and gently pry up pulling the black housing out of the silver Back housing, while doing this you may need another spreader to pry the bottom and then go around the sides to make sure it comes out freely.
Man, excellent photos showing us the goods. What i wanna know is that the heck causes the power button to sink in the way it does. Seems hit and miss with these. Some people get very responsive power buttons, others get mushy clicky feels. Weird.
I couldnt do that to my phone. Were you able to put it back together and have it still look good and function as before?
Acill said:
I couldnt do that to my phone. Were you able to put it back together and have it still look good and function as before?
Click to expand...
Click to collapse
Yes it works just fine, i have been abusing it on purpose, it has yet to screw up, I love this phone. But i have to send it in here soon lol
Good job!! By the way you left you jar of weed in the photos, LOL BLAZE ON!!!!!!!!!
serialtoon said:
Man, excellent photos showing us the goods. What i wanna know is that the heck causes the power button to sink in the way it does. Seems hit and miss with these. Some people get very responsive power buttons, others get mushy clicky feels. Weird.
Click to expand...
Click to collapse
Here is the power button, it has a black sticker over the top, but the button is just a little piece of plastic that pushes the little button, not much contact area really.
rpomponio said:
Good job!! By the way you left you jar of weed in the photos, LOL BLAZE ON!!!!!!!!!
Click to expand...
Click to collapse
I live in Washington, i just stopped caring, and apparently noticing the photobomb...
itzsnookums said:
Here is the power button, it has a black sticker over the top, but the button is just a little piece of plastic that pushes the little button, not much contact area really.
Click to expand...
Click to collapse
Iiiiinteresting. I remember when the HTC One X was new, i took that think apart and bent the casing of it and ended up cracking the plastic casing. Made me sad, then i found all the parts on ebay to get it back to "mint" condition. Exciting. :good:
serialtoon said:
Iiiiinteresting. I remember when the HTC One X was new, i took that think apart and bent the casing of it and ended up cracking the plastic casing. Made me sad, then i found all the parts on ebay to get it back to "mint" condition. Exciting. :good:
Click to expand...
Click to collapse
You know this was easier to take apart then trying to get my dam phone to focus...i hope HTC fixes the autofocus issue......
itzsnookums said:
I live in Washington, i just stopped caring, and apparently noticing the photobomb...
Click to expand...
Click to collapse
One day ..one day I'll smoke with you... Introduce you to some cali greens...sure you guys got some great stuff in Washington too
a box of kittens said:
One day ..one day I'll smoke with you... Introduce you to some cali greens...sure you guys got some great stuff in Washington too
Click to expand...
Click to collapse
Ha, that i doubt...until we can go to the nearest store and buy it =-p
Yea I'm in cali and got my medical license. Smoke on!!!! Anyways. I got a gap on top speaker cover. Is it held on with adhesive?? I'm thinking about using a hair drier to heat it up and hopefully get rid of the gap.. if you can get picture of back side of top speaker grill I would greatly appreciate it. :thumbup: thank you in advance
Sent from my HTC One using xda app-developers app
Here you go.....just adhesive and a screw thats in the inside, my replacement has I gap to.....but haven't played yet to fix it....
Sweetness for tapatalk being a POS and not uploading.....
Sent from my HTC One using xda premium
Thanks brother I appreciate it!!
Sent from my HTC One using xda premium
rpomponio said:
Thanks brother I appreciate it!!
Sent from my HTC One using xda premium
Click to expand...
Click to collapse
I got a video uploading right now =-)
itzsnookums said:
I got a video uploading right now =-)
Click to expand...
Click to collapse
Cool! that will be cool to watch thanks!
:good::good:
rpomponio said:
Cool! that will be cool to watch thanks!
:good::good:
Click to expand...
Click to collapse
its not that good lol but gets the general point across.....also remember that the nicks at the bottom were there before hand....
video will be uploaded tomorrow, sorry upload is taking forever
If you have a gap, there is no need to take the phone apart.
Just get some super glue in there and clamp tight.
And here are the OEM replacement parts if you screw up
http://www.etradesupply.com/oem-htc-one-rear-housing.html
I was wondering. Is it possible to ONLY touch the body (ie the housing + speaker grills) and replace them? There are a lot of people who scratched their ones and may want to replace the outside.
sauprankul said:
If you have a gap, there is no need to take the phone apart.
Just get some super glue in there and clamp tight.
And here are the OEM replacement parts if you screw up
http://www.etradesupply.com/oem-htc-one-rear-housing.html
I was wondering. Is it possible to ONLY touch the body (ie the housing + speaker grills) and replace them? There are a lot of people who scratched their ones and may want to replace the outside.
Click to expand...
Click to collapse
???? not sure what u mean?
itzsnookums said:
???? not sure what u mean?
Click to expand...
Click to collapse
In the picture, it seems you have thoroughly torn down the entire phone.
Some people may wish to simply change the speaker grills or the rear case (metal + plastic sides). On a scale of 1-10, how hard would that be?
Hey just a warning for you guys the s pen plastic is cheap as we all can tell so today was showing the phone to some friends forgot the s pen on the couch stupid mistake started playing ps3 anyway after i pulled my phone back out i relized the pen wasnt in there turns out some on ended up sittin on it and it cracked right at the bottom of the button still works but bent and very close to breaking in half if i dont get some crazy glue also phone is new so gonna be hard to get just the s pen for at least a month but thats my stupid mistake be careful with your s pens guys
Good luck finding any plastic which can stand up to your mates arse when it's moulded so thin. ?
Sent from my SM-N9005
I don't think anyone would expect the spen to survive someone squatting on it. But thanks for the warning. Ha.
Sent from my GT-N5110 using Tapatalk
Well i made my problem a whole lot worse the rest of the pen casing cracked while it was in the phone i pulled it out pen is still fine but top half of the plastic casing is locked in there any one have any idea how to get it out. Theres a samsung repair center in my area but i dont want go there if i dont need too i can open the cover up and take it out but im afarid of voidinh the warrenty
It wasn't clever putting it back in like that. The pen is held with a small sprung clip which locates a tiny grove on the pen about 12mm from the tip, that will hold the tip in the phone fairly well.
Your choices are very limited, if it was me I would take the back cover off, look at the pattern in the plastic where the pen goes & drill a tiny hole about 3mm from the end .. ( this will be between the tip of the pen & the clip) use a thick sewing needle or tooth pick innthat hole to push the broken end past the clip & it will slide out on its own.
When done a spot of black glue on the hole if you want.
Sent from my SM-N9005 using xda app-developers app
Pat. said:
It wasn't clever putting it back in like that. The pen is held with a small sprung clip which locates a tiny grove on the pen about 12mm from the tip, that will hold the tip in the phone fairly well.
Your choices are very limited, if it was me I would take the back cover off, look at the pattern in the plastic where the pen goes & drill a tiny hole about 3mm from the end .. ( this will be between the tip of the pen & the clip) use a thick sewing needle or tooth pick innthat hole to push the broken end past the clip & it will slide out on its own.
When done a spot of black glue on the hole if you want.
Sent from my SM-N9005 using xda app-developers app
Click to expand...
Click to collapse
Interesting while right now i have the pen the tip everything when i pull it out but the top plastic covering on the pen is the part that cracked off and is stuck so i might be able to find some kind of long thin needle and push the clip but im just gonna get samsung to do it cause its still under warrenty of course its a hassle to find the time to go in but its good to have a samsung store in the area
I can't see any way they would remove it
Sent from my SM-N9005 using xda app-developers app
Pat. said:
I can't see any way they would remove it
Sent from my SM-N9005 using xda app-developers app
Click to expand...
Click to collapse
I dont think you understand the part the broke heres a pic of the pen
Yes I do. All my posts have been on the understanding that part of the casing at the tip is left in your phone. The small hole I am suggesting is up the top end (near the the on/off switch).
Sent from my SM-N9005 using xda app-developers app
Pat. said:
Yes I do. All my posts have been on the understanding that part of the casing at the tip is left in your phone. The small hole I am suggesting is up the top end (near the the on/off switch).
Sent from my SM-N9005 using xda app-developers app
Click to expand...
Click to collapse
Oh ok so you mean drill a hole in the casing put in a needle pull out right ? Also wondering if I take off just the back plate there's no void stickers on there right ?
Small hole to put something in to PUSH the part past the little clip & it will slide the rest of the way on its own & out of the phone.
Sent from my SM-N9005 using xda app-developers app
Only remove battery cover same as when inserting sim or sd. . No void doing that but small hole might void if you don't fill after with black glue
Sent from my SM-N9005 using xda app-developers app
There is a void sticker just past the tip of the pen chamber. You need to remove the screw under it to get the back plate off.
Sent from my SM-N9005
Pat. said:
Only remove battery cover same as when inserting sim or sd. . No void doing that but small hole might void if you don't fill after with black glue
Sent from my SM-N9005 using xda app-developers app
Click to expand...
Click to collapse
Advicing a guy that sits on the spen until it cracks and then puts it back in the slot to drill a note 3 ain't very wise imo!
what I would do is this: get a long and thin needle , bend it 2 mm with a precision plier at the tip, and fish the missing part from the slot.
it will work easy .
good luck
GMoneyDTP said:
Well i made my problem a whole lot worse the rest of the pen casing cracked while it was in the phone i pulled it out pen is still fine but top half of the plastic casing is locked in there any one have any idea how to get it out. Theres a samsung repair center in my area but i dont want go there if i dont need too i can open the cover up and take it out but im afarid of voidinh the warrenty
Click to expand...
Click to collapse
You must know this already by now and maybe this won't help your situation but just before you said what I quoted I was thinking: "man now he will need to leave it out." Next I read what fallowed... I hope in future similar situation you will be more "aware".
Good luck mate
Sent from my SM-N900W8 using xda premium
heavylift said:
Advicing a guy that sits on the spen until it cracks and then puts it back in the slot to drill a note 3 ain't very wise imo!
what I would do is this: get a long and thin needle , bend it 2 mm with a precision plier at the tip, and fish the missing part from the slot.
it will work easy .
good luck
Click to expand...
Click to collapse
The small hole is what I would do & it is low risk.
I would not poke things up there as it could damage the retaining clip. "Pen removed" sensor.
In fact some phones that had stylus put a small hole there to allow to blow dust out.
I really don't know why I made the stupid mistake of putting it back in but yeah I have the n900w8 canadain version there's no sticker on any of the back plate screws I'm asking about under it ?
If you can do it without removing void stickers or making a hole it's better but be very careful if you start taking the phone apart. Some screws can have a "paint seal".
Its all good now I opened up the back cover while I was popping it up the piece fell out sensor still works at least for detecting that its out and that I'm away from it so that's good now all I need is some crazy glue To glue it back together and then I'm gonna order a new s pen
PSA!!! Cars are cheap, i crashed my car into the pole while i was playing farmville on my Note 3 and driving at the same time and my bumper split in 2 and broke my radiator and a few other engine parts, but it's not my fault, the car is cheap:good:
Hey all!
So I received my new black S4 a couple of days ago and had been enjoying it a lot. That is, until I tried to clean the gap between the bezel and the glass that is accumulating dust over time. As I searched the internet on how to do that, I found out that the corner of a piece of paper would do the trick since a lot of people do this.
So one evening I did as I read on the internet and indeed, a lot of dust came out and I was happy. However, the next morning when daylight shone on my precious S4 I realised that the piece of paper I had slid through the gap also caused it to scratch the very side of the glass!
I was quite surprised that a piece of paper was able to do such a thing but the thought of a papercut made it somewhat obvious.
Now, the whole left side of the glass has an extra white line (aka the scratch) running along the side of the glass (it looks as if it's just beneath the glass). It is only visible when light is shining in particular directions on the phone. Still, I'm quite pissed at myself right now for doing such a thing.
So does anyone else clean the gap with a piece of paper? Did you guys notice any scratch/line along the side of the glass afterwards?
(Sorry if I'm being too OCD about this, I guess I have to find a way to get over it )
well, you've got every right to be oc coz our s4 is a premium phone haha
I never did try using paper.. What i use is a scotch tape and push it carefully with something thin like a needle but thanks for the info my friend.. This has given me a heads up
And sorry bout the scratches tsk
Sent from my GT-I9505 using XDA Premium 4 mobile app
saywhatt said:
well, you've got every right to be oc coz our s4 is a premium phone haha
I never did try using paper.. What i use is a scotch tape and push it carefully with something thin like a needle but thanks for the info my friend.. This has given me a heads up
And sorry bout the scratches tsk
Sent from my GT-I9505 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Hmm, that could have been a better option now to think of it. The thing is I didn't feel any friction at all while I was sliding the paper through it so I thought no harm would be done.
Anyway below is shown what I ended up with.
It does look like dirt between the glass and the bezel. However, I just can't remove it so I automatically assumed it must be some damage to the side of the screen beneath. I wonder what's actually at the bottom of the gap.
Still not able to digest this ;P
Hi all,
I just got my new Galaxy S5 and the first I wanted to do was to take a few pictures underwater. However, after I put the battery on, I noticed that the back cover makes a creaking noise when I push it near the heart rate sensor and I can see the back cover near the sensor going down when I push it. Does this compromises the water resistance of the phone?
Regards
I'm thinking that there might be water remnants inside. Water + rubber is known to produce squeaking noise.
I still haven't put the phone underwater. I noticed the problem wheni was taking the phone out of the box. When I apply light force to the area around the sensor I can see the back cover moving up and down and it makes more of a clicking noise. Any ideas?
Sent from my SM-G900H using XDA Free mobile app
It could be a part inside is just bumping to another part. Alignment is not 100% perfect, especially the rubber part for water-resistance because it was just stuck to the cover and is originally not part of the cover itself.
Thanks. One last question. So, after the phone has been submerged and I take it out, fully dry it from the outside, is it normal to be water under the back cover? The part which is not covered by the rubber part?
Sent from my SM-G900H using XDA Free mobile app
Anyone?
Sent from my SM-G900H using XDA Free mobile app
Thin_Bezel said:
Thanks. One last question. So, after the phone has been submerged and I take it out, fully dry it from the outside, is it normal to be water under the back cover? The part which is not covered by the rubber part?
Click to expand...
Click to collapse
The rubber lining on the interior face of the back cover should keep any liquid from continuing its entry to the phone's internals, but it doesn't prevent the liquid from sipping through from the outside. Check out how large the notch at the power button area that you use to open up the back cover.
But you should dry the phone first as is for a few hours to be sure no more liquid could enter. When you're sure that it's safe, open the back cover then remove the battery and dry the phone face up so that any liquid residue will go down, at the same time dry the back cover separately too. And be sure that everything is dry, including the ports, before you reattach the battery.
And if the unfortunate event that the phone turned off when it was wet, do not attempt to turn it on. Remove the back cover and battery immediately and let them all dry for at least 24hrs, focus an electric fan to them if you can, to be sure that you max out the opportunity to dry them. And during the drying process, do not keep on touching them to avoid liquid moving inside.
I hope this answers your question.
Hi there, even I have the same problem. I noticed that both the the back cover and the s-view cover shows a slight on the power button side in the centre. I firmly believe mine is a phone manufacturing issue as two cover can have the exact same issues...let see if I can get replacement as its not cover problem. Check the attached pic
bryanfuryin22 said:
Hi there, even I have the same problem. I noticed that both the the back cover and the s-view cover shows a slight on the power button side in the centre. I firmly believe mine is a phone manufacturing issue as two cover can have the exact same issues...let see if I can get replacement as its not cover problem. Check the attached pic
Click to expand...
Click to collapse
It's an alignment problem that I have explained to OP. That rubber lining for water-resistance is prone for misalignment and probably warping too. Rubber is known to stretch due to rise in temperature. If it warped or misaligned to an embossed area, that part will be more elevated than the rest.
I have same problem, but I got used to it.
When I put my back cover on girlfriends phone there is no noise.
Its like the problem is phone itself.
I tested its waterproof capabilities even though the back cover wasn't properly aligned. Every thing was good. No water got inside the internals.
Sent from my SM-G900H using XDA Free mobile app
You sir are brave!
Sent from my SM-G900F using Tapatalk
xXFearXx said:
You sir are brave!
Sent from my SM-G900F using Tapatalk
Click to expand...
Click to collapse
Haha, I was thinking the same thing, I would have never tried that, though it should of course not be any poblem since it is IP67 certified.
xXFearXx said:
You sir are brave!
Sent from my SM-G900F using Tapatalk
Click to expand...
Click to collapse
I 2nd that!
I wont "test" my water proof ability with a cover that fits correctly :laugh:
Even though no water gets in, I have a question again. The water does go inside the back cover but it doesn't go as the rubber line which is a good thing (That's how it is supposed to work).
I always wipe the water inside after a bath but if I am at a pool for example and I put the phone inside the water but then I don't wipe the water inside for about, 6-7 hours, would there be a problem?
Sent from my SM-G900H using XDA Free mobile app
Anyone knows if it is on to not wipe the inside of the phone for a few hours?
Sent from my SM-G900H using XDA Free mobile app
Thin_Bezel said:
Anyone knows if it is on to not wipe the inside of the phone for a few hours?
Sent from my SM-G900H using XDA Free mobile app
Click to expand...
Click to collapse
That part is considered to be harmless to get wet, so it isn't a problem if you do not remove the water there for even forever.
I have one last concern and I hope other Galaxy S5 users can help. When you remove the battery cover, you will notice that the area where the side bezel and the back of the phone are connected, it looks like it is melted in order to prevent water.
However, not all the area looks like it is melted. For example, at the area of the bezel where the volume buttons are, there is a small gap between the bezel and the back part of the phone and I can put my nail inside the gap.
I am wondering if all units have this gap or if my device is faulty. Any help is appreciated.
Sent from my SM-G900H using XDA Free mobile app
Thin_Bezel said:
I have one last concern and I hope other Galaxy S5 users can help. When you remove the battery cover, you will notice that the area where the side bezel and the back of the phone are connected, it looks like it is melted in order to prevent water.
However, not all the area looks like it is melted. For example, at the area of the bezel where the volume buttons are, there is a small gap between the bezel and the back part of the phone and I can put my nail inside the gap.
I am wondering if all units have this gap or if my device is faulty. Any help is appreciated.
Sent from my SM-G900H using XDA Free mobile app
Click to expand...
Click to collapse
I have the exact same small gap at the same location, so I think it is normal and is that way by design.
johan81 said:
I have the exact same small gap at the same location, so I think it is normal and is that way by design.
Click to expand...
Click to collapse
Thank god. I thought I was screwed. Especially because my beatiful S5 has been diving for the days in the pool. Enjoying vacations. Taken with the Galaxy S5 front facing camera
Sent from my SM-G900H using XDA Free mobile app