I left a thread about this in the android section but now I realize that this is probably the better place to do it (I need to send my phone back and get a new one on warranty):
Can any one tell me is this the stock info on a t-mobile htc hd2 stock:
on the boot (three color red green and blue) screen it says:
SPL-2.10.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0X50
and on the ohter boot screen with the three numbers it says
R 2.15.50.14
G 15.42.50.11u
D 3.14.04666 8g
Will they be able to tell I messed with the phone given this info? In other words can I get my warranty with this?
Thanks in advance
Related
hi, pretty sure i am ok here but after some clarification from the experts please.
ok my phone has to go back tomorrow to htc due to overheating issues and i hope i have managed to revert back to stock rom and removed hspl from the phone?
this is the info showing on the tri colour boot screen
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Just in case any of you experts know this is the info at the white htc screen with the rom, radio as well???
R 2.06.51.07
G 15.30.50.07U
D 1.66.76641
Thanks in advance guys.
Sorry if this is a repost but I want to make sure before I send my phone to T-Mobile tomorrow morning. If I have the correct numbers listed on the flash boot up screen. Please reply ASAP. Thank you
PB81120 HX-B3
SPL-2.10.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Yup, your fine my friend.
Kenichi
Your the MAN!!! Thanks
more important than the rom version is being sure hspl has been removed (assuming you have applied hspl in the past)
to check, enter bootloader and make sure the number by spl ends .0000 and not .hspl
Hi,
My HD2 was bricked and repaired once using jTag method by a repair center. Now I am using the Android 2.3.3 Gingerbread. When it heats up, it hangs up frequently when using call functionality. I think it's because of the heat + the wrong radio version or so.
Can anyone suggest me what could be done for this ? Maybe change a stable radio ?
When I boot it into bootloader it says
PB81120 SS-B3
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
post in the Q&A section not the dev section
The touch input on my TMOUS HD2 stopped working so I have to return it now that I received the replacement in the mail. I put WM6.5 stock from the T-Mobile website back on it. Then I noticed HSPL was still there so I extracted the LEOIMG.nbh from the same WM archive and flashed it.
The old, broken phone says:
SPL-2.08.0000 8G XE
MicroP(TOUCH) 0x40
The new one says:
SPL-2.10.0000 8G XE
MicroP(TOUCH) 0x50
Is that OK that those are different when I return it?
What antenna version should I have on it?
Is there anything else I need to make sure I wipe out before returning it?
In my device (android) the Bootloader is standing:
PB81*** HX-B3
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Some people said that is Hynix device or something like that
So anybody can explain me what is the different between these
because some android kernel (dorimanx 6.0 and above) can boot on my device, it stucks at go go go screen
Pls help me
Tks in adv