Related
Hello,
I am relatively new to this and clearly making some mistakes, from what I have found on these forums I can't see anyone else having the same issues with this device. Any help would be greatly appreciated. So here goes:
I recently tried installing SHOstock's rom, everything appeared successful and the phone began to boot, but hung on the samsung logo with the padlock for 10+ minutes. I tried to reboot, same thing. When booting back into recovery to do a wipe and give it another shot, I was prompted for a password (which I did not set up). So I decided I had probably screwed something up and tried to flash back to stock with Odin. Odin failed, and now all I can get is "Firmware upgrade encountered an issue..." I get this even when trying to enter recovery. I've tried connecting to Kies as well, but no such luck, as it doesn't connect to the device.Currently working on downloading another copy of the stock software to try with Odin again.
Any help is appreciated,
Thanks
What S4 do you have( model#)?
Are you sure you are using the correct firmware?
Are you sure the Kernel and ROM you tried to install were correct for your phone?
Did ODIN recognize your phone or did it fail during / after installation? Was there a specific message?
Re-downloading is good (you said you were doing that now) just to make sure it wasn't a bad download.
scott14719 said:
What S4 do you have( model#)?
Are you sure you are using the correct firmware?
Are you sure the Kernel and ROM you tried to install were correct for your phone?
Did ODIN recognize your phone or did it fail during / after installation? Was there a specific message?
Re-downloading is good (you said you were doing that now) just to make sure it wasn't a bad download.
Click to expand...
Click to collapse
First, thank you for the quick response.
After redownloading from a different source, Odin's flash passed this time, and after a factory reset I am back in. Thank you again for the help.
Hi,
Currently there is not much on the phone, at least nothing to start up. I had CM, but had to go back so I tried the guide posted on this forum. With little success. So now im not sure where I stand as the phone is in a state without a ROM. When I try to start up normally i get "firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
Anyone can help me with installing fresh stock Samsung ROM?
Thanks in advance!
Sincerely,
Tho_kva2
Which was your last stock rom bevor you installed cm?
And which stock rom did you try to flash after cm?
Did they had the same product key?
Was the flashing process successful or did odin say "fail"?
And how is your current knox status? 0x1?
Send from my Galaxy S4 using Tapatalk
Not sure, but my phone was up to date with the latest update from Samsung.
I first tried to use "Norway (telenor)" first as, and when that failed I tried "Norway 4.4.2" Both found in the second post of the Guide.
Product key?
Odin said Fail. I tried multiple times with different odin versions and with PIT file.
Is it the "Knox warranty void" is so 0x1
And the latest original firmware running on your phone was it a Norway (telenor) firmware?
With product key i meant the csc.
The old firmware and the one you want to flash now have to have the same csc, i guess.
You can also flash a custom recovery and try to wipe and then flash again.
Send from my Galaxy S4 using Tapatalk
I'm not sure what the original firmware was, but it was the stock firmware i got with the phone when i bought it + updates.
CSC is TEN (Norway)
I do not know how to do a custom recovery, im a total noob on this subject of flashing and modding phones. Got any kind of guide or directrions to point me in? Sorry for not knowing squat, but hope you or someone else here can help me!
Hi,
okay, before you flash a recovery, you can try to flash another firmware but it have to be android 4.4.2 norway TEN
Did you also follow this note here?
"Odin troubleshooting:*If Odin accidentally gives you "fail" try the following:
- Repeat procedure.
- Make sure that all actions of Kies are disabled from task manager.
- Change usb port.
- Try another usb cable (make sure it is the original).
- Try another Odin version.
- Uninstall and re-install driver.
- Use pit file.
- Try another computer."
When odin will continue failing then try this.
http://www.usp-forum.de/downloads.php?do=file&id=1531
This is a 4 part open Europe firmware. Try to flash it...First time without pit,when odin failed try with pit...
If nothing helped, then you can install a custom recovery.
You once installed a recovery, before you flashed CM, remember?
But I will look for a guide and the right files.
Send from my Galaxy S4 using Tapatalk
It worked with the European version! Cheers mate Oh, it was without the pit.
Atleast android is installed hehe. but keyboard keeps crashing so cant type anything, and I cant turn on wifi; I get "Security notice, your device's security has blocked an action that is not permitted. No further action is required" -Knox Notification Manager.?
Oh and I got no SIM card to try at the phone atm. will get it later
So waht should be the next step?
Did you rooted this firmware already?
Try to fullwipe again. I thought this message only pops up, when the devise is rooted and Knox still not deleted... mysterious
Send from my Galaxy S4 using Tapatalk
I did not root it. I will try to wipe
Edit:
****ed up. Tried flashing the same again, and it failed lol.. so now im back to where I was before the phone "worked" again.
So I think I should get a recovery. Any thought?
Lol that's crazy. Also tried 4 part with pit?
And when you flash a Norway firmware again? Maybe it will work now, i don't know what's going on there
http://forum.xda-developers.com/showthread.php?t=2397108
This is CWM recovery for i9505, you have to flash the .tar file with odin in PDA or AP. It's your choice, whether you install the touch or non touch version.
Edit: anything new?
Send from my Galaxy S4 using Tapatalk
My S4 can't turn on (the first screen of the model is starting and then nothing, downloading and recovery mods are working), its all happend after i did something wrong when I have tryed to root the phone, i puted the .tar file in the bootloader line in odin insted of the PDA line, I also tryed to flash stock rom to it and it's always fail. is there any solution or is it lost?
burik1994 said:
My S4 can't turn on (the first screen of the model is starting and then nothing, downloading and recovery mods are working), its all happend after i did something wrong when I have tryed to root the phone, i puted the .tar file in the bootloader line in odin insted of the PDA line, I also tryed to flash stock rom to it and it's always fail. is there any solution or is it lost?
Click to expand...
Click to collapse
Well you did something horribly wrong my friend. Did you not refer any tutorials?
Mindless efforts.
Always flash via PDA.
Try changing the cable and the usb port and flash the latest updated 4.4.2 firmware for your phone using the PDA tab and revert.
@MAX 404
"If someone helps, never forget to hit thanks ? "
I got a bricked Samsung Galaxy Note 4 (910F) vodafone branded.
it's totally broken I can't start it, can't go into recovery (the hardware buttons are OK).
I can only go into download mode.
tried flashing everything with odin back to stock. followed many different instructions and now I'm lost.
can someone tell me what exact files I need?
I think I have the right firmware downloaded BUT what about the bootloader? on sammobile under germany-vodafone there are so many different versions which one shall I choose?
AND: Do I need CSC? if so which one and where to find? Couldn't find it on sammobile.
And am I right with putting the bootloader under BL, the firmware under AP, the CP (whatever this is) under CP, the csc under csc?
repartition unchecked as I read somewhere.
I still don't understand what this "pit" file is for and I'm not sure if I have the right one.. never had a phone with sooo many different firmware files..
I'm used to flash via fastboot "recovery.img, boot.img, system.img" odin is a new thing for me
HELP PLEASEEE :'(
the reactivation lock is on.
nekrosmsk said:
I got a bricked Samsung Galaxy Note 4 (910F) vodafone branded.
it's totally broken I can't start it, can't go into recovery (the hardware buttons are OK).
I can only go into download mode.
tried flashing everything with odin back to stock. followed many different instructions and now I'm lost.
can someone tell me what exact files I need?
I think I have the right firmware downloaded BUT what about the bootloader? on sammobile under germany-vodafone there are so many different versions which one shall I choose?
AND: Do I need CSC? if so which one and where to find? Couldn't find it on sammobile.
And am I right with putting the bootloader under BL, the firmware under AP, the CP (whatever this is) under CP, the csc under csc?
repartition unchecked as I read somewhere.
I still don't understand what this "pit" file is for and I'm not sure if I have the right one.. never had a phone with sooo many different firmware files..
I'm used to flash via fastboot "recovery.img, boot.img, system.img" odin is a new thing for me
HELP PLEASEEE :'(
the reactivation lock is on.
Click to expand...
Click to collapse
The note 4 firmware is usually only 1 file that contains all you need. It contains the bootloader and CSC that you pick during download. Just pick the CSC for your country.
This is unless you get a 4 file repair firmware, which contains separate bootloader, system, and CSC files.
The pit file is only needed to repartition your device.
But with all off that aside, you state that your activation lock is activated. These means the phone was password protected.
If you tell me your country, I can at least point you to the correct firmware. So at least you'll know you got the correct one.
But as far as the activation lock, I can't help with that. "Google"
Edit. I now see you mentioned Germany Voda.
So here's the most current firmware for your device.
https://fws03.updato.com/GALAXYNOTE4/SM-N910F/TCL/SM-N910F_1_20171228192640_l5rw6mqv67.zip
Download and unzip.
Then if it's just 1 file that's .md5 then you put it in AP slot.
If it's 4 files put them in appropriate slots.
aaron74 said:
The note 4 firmware is usually only 1 file that contains all you need. It contains the bootloader and CSC that you pick during download. Just pick the CSC for your country.
This is unless you get a 4 file repair firmware, which contains separate bootloader, system, and CSC files.
The pit file is only needed to repartition your device.
But with all off that aside, you state that your activation lock is activated. These means the phone was password protected.
If you tell me your country, I can at least point you to the correct firmware. So at least you'll know you got the correct one.
But as far as the activation lock, I can't help with that. "Google"
Edit. I now see you mentioned Germany Voda.
So here's the most current firmware for your device.
https://fws03.updato.com/GALAXYNOTE4/SM-N910F/TCL/SM-N910F_1_20171228192640_l5rw6mqv67.zip
Download and unzip.
Then if it's just 1 file that's .md5 then you put it in AP slot.
If it's 4 files put them in appropriate slots.
Click to expand...
Click to collapse
This reactivation lock doesn't matter I found a solution how to bypass it when the phone is set up running android.
my question is, is it possible to flash firmware to the note4 at all with reactivation lock on? Or is that just an android thingy?
And yes please that would be nice if you show me the right firmware.
My model:
N910F GSMH
I believe it is vodafone branded because when it once worked it showed a vodafone logo while starting up.
my country is Germany.
I hope thats enough info :/
nekrosmsk said:
This reactivation lock doesn't matter I found a solution how to bypass it when the phone is set up running android.
my question is, is it possible to flash firmware to the note4 at all with reactivation lock on? Or is that just an android thingy?
And yes please that would be nice if you show me the right firmware.
My model:
N910F GSMH
I believe it is vodafone branded because when it once worked it showed a vodafone logo while starting up.
my country is Germany.
I hope thats enough info :/
Click to expand...
Click to collapse
I believe it should still flash with lock. If it isn't flashing something is wrong.
If you can't get Odin to flash that firmware try this and see what happens.
Download TWRP and flash it. Can you boot into recovery then? If so download a custom rom and flash it and see what happens.
TWRP: https://eu.dl.twrp.me/trlte/twrp-3.2.1-0-trlte.img.tar
Do you have Samsung drivers installed on PC? http://developer.samsung.com/common/download/check.do?actId=698
Do you have a good Odin? https://dl.sammobile.com/Odin3-v3.13.1.zip
aaron74 said:
I believe it should still flash with lock. If it isn't flashing something is wrong.
If you can't get Odin to flash that firmware try this and see what happens.
Download TWRP and flash it. Can you boot into recovery then? If so download a custom rom and flash it and see what happens.
TWRP: https://eu.dl.twrp.me/trlte/twrp-3.2.1-0-trlte.img.tar
Do you have Samsung drivers installed on PC? http://developer.samsung.com/common/download/check.do?actId=698
Do you have a good Odin? https://dl.sammobile.com/Odin3-v3.13.1.zip
Click to expand...
Click to collapse
I have the right latest samsung drivers installed yes.
I have the Odin version you just sent a link of. ( I also tried different older versions but no success).
I can't boot into recovery doesn't work. the hardware buttons are 100% working as I have to press vol+ to confirm to go into download mode.
I tried flashing TWRP and CWM both didn't work "custom recovery blocked by A/L error".
I can successfully flash firmware with Odin. It says "PASS" and then the phone reboots and is stuck on Samsung Logo. and sometimes it just shows blue text "recovery booting" but is stuck. nothing happens.
nekrosmsk said:
This reactivation lock doesn't matter I found a solution how to bypass it when the phone is set up running android.
my question is, is it possible to flash firmware to the note4 at all with reactivation lock on? Or is that just an android thingy?
And yes please that would be nice if you show me the right firmware.
My model:
N910F GSMH
I believe it is vodafone branded because when it once worked it showed a vodafone logo while starting up.
my country is Germany.
I hope thats enough info :/
Click to expand...
Click to collapse
Hey sorry the link you've sent doesn't work :/
aaron74 said:
The note 4 firmware is usually only 1 file that contains all you need. It contains the bootloader and CSC that you pick during download. Just pick the CSC for your country.
This is unless you get a 4 file repair firmware, which contains separate bootloader, system, and CSC files.
The pit file is only needed to repartition your device.
But with all off that aside, you state that your activation lock is activated. These means the phone was password protected.
If you tell me your country, I can at least point you to the correct firmware. So at least you'll know you got the correct one.
But as far as the activation lock, I can't help with that. "Google"
Edit. I now see you mentioned Germany Voda.
So here's the most current firmware for your device.
https://fws03.updato.com/GALAXYNOTE4/SM-N910F/TCL/SM-N910F_1_20171228192640_l5rw6mqv67.zip
Download and unzip.
Then if it's just 1 file that's .md5 then you put it in AP slot.
If it's 4 files put them in appropriate slots.
Click to expand...
Click to collapse
hey thanks in advance, but this link doesnt work it says "hotlinking is not cool". anyways I searched the firmware for my model number on this site and applied the "germany vodafone" filter. but there are still soo many different entries which one shall I choose? The latest date?
nekrosmsk said:
hey thanks in advance, but this link doesnt work it says "hotlinking is not cool". anyways I searched the firmware for my model number on this site and applied the "germany vodafone" filter. but there are still soo many different entries which one shall I choose? The latest date?
Click to expand...
Click to collapse
Here's webpage
https://updato.com/firmware-archive-select-model?record=58770125168D11E89F15FA163EE8F90B
After you flash, how long are you waiting for it to boot?
Sometimes it takes awhile.
aaron74 said:
Here's webpage
https://updato.com/firmware-archive-select-model?record=58770125168D11E89F15FA163EE8F90B
After you flash, how long are you waiting for it to boot?
Sometimes it takes awhile.
Click to expand...
Click to collapse
Thanks for the link I'm downloading.
After flashing odin says PASS and my note 4 reboots. then there are 2 cases which in my view appear randomly. Either it shows the samsung logo and is stuck.
OR it shows the samsung logo and a blue little text in the upper left corner saying "recovery booting" and is stuck. I waited like 5 minutes. shall I wait longer? :/ hm..I'll try
OH and sometimes the screen just goes black idk if it really turns off after getting stuck on samsung logo.
Pull the battery, leave it out for 10+ minutes
Put battery back in
Boot to download mode (Power + Vol Down + Home)
Then try (re)flashing stock ROM via odin, i would try the earliest you can find to have the best chance, you can always flash a later one if you get it running
Better range of ROMS from sammobile, i never use updato for that reason: https://www.sammobile.com/firmwares/galaxy-note4/SM-N910F/VD2/
If none of that works, then its likely you have a hardware fault ...emmc or other
stylemessiah said:
Pull the battery, leave it out for 10+ minutes
Put battery back in
Boot to download mode (Power + Vol Down + Home)
Then try (re)flashing stock ROM via odin, i would try the earliest you can find to have the best chance, you can always flash a later one if you get it running
Better range of ROMS from sammobile, i never use updato for that reason: https://www.sammobile.com/firmwares/galaxy-note4/SM-N910F/VD2/
If none of that works, then its likely you have a hardware fault ...emmc or other
Click to expand...
Click to collapse
So I tried flashing. after flashing OH WONDER it said recovery booting and then it showed this green android logo thing with a rotating icon in it "you know what I mean" but then it stopped and just turned off.. I could freak out really.. I tried flashing again. same issue. I could then press the recovery mode key combo to get into this rotating android logo screen but everytime it just freezes and turns off. yes the battery is fully charged before I started flashing this firmware now. I flashed the one u said the earliest. So Now I tried the one the other guy here showed me. didn't work either. it just gets stuck at samsung logo. I found a repair firmware for my model containing (pit, bl, ap, cp, csc and odin) I flashed all but odin fails "write error". I then tried odin v3.0.7 but then it got stuck while flashing the system image. I waited like 1 hour. nothing. tried it again. nothing it freezes on the same position. I then tried the same on the latest versions of odin v3.12.3, 3.12.7 and on 3.13.1 but it also freezes on system.img.ext4 image flashing..
nekrosmsk said:
So I tried flashing. after flashing OH WONDER it said recovery booting and then it showed this green android logo thing with a rotating icon in it "you know what I mean" but then it stopped and just turned off.. I could freak out really.. I tried flashing again. same issue. I could then press the recovery mode key combo to get into this rotating android logo screen but everytime it just freezes and turns off. yes the battery is fully charged before I started flashing this firmware now. I flashed the one u said the earliest. So Now I tried the one the other guy here showed me. didn't work either. it just gets stuck at samsung logo. I found a repair firmware for my model containing (pit, bl, ap, cp, csc and odin) I flashed all but odin fails "write error". I then tried odin v3.0.7 but then it got stuck while flashing the system image. I waited like 1 hour. nothing. tried it again. nothing it freezes on the same position. I then tried the same on the latest versions of odin v3.12.3, 3.12.7 and on 3.13.1 but it also freezes on system.img.ext4 image flashing..
Click to expand...
Click to collapse
Try the Samsung Smart Switch for PC - like this : https://www.youtube.com/watch?v=9QhJngOuLQ4&t=337s
Good luck, maybe it will work - for me it did work for the 910C.
w41ru5 said:
Try the Samsung Smart Switch for PC - like this : https://www.youtube.com/watch?v=9QhJngOuLQ4&t=337s
Good luck, maybe it will work - for me it did work for the 910C.
Click to expand...
Click to collapse
doesnt work. I tried several versions of smartswitch AND samsung kies. nothing works it always says my model is not supported. I reinstalled drivers. tried on another pc. tried another usb port. yes I'm using the original stock usb cable. model not supported. But I've also read that in other threads that the 910F model seems to be unknown by kies or smartswitch. I'm rly starting to hate samsung now. I have never ever had so many problems with flashing and so on.
nekrosmsk said:
So I tried flashing. after flashing OH WONDER it said recovery booting and then it showed this green android logo thing with a rotating icon in it "you know what I mean" but then it stopped and just turned off.. I could freak out really.. I tried flashing again. same issue. I could then press the recovery mode key combo to get into this rotating android logo screen but everytime it just freezes and turns off. yes the battery is fully charged before I started flashing this firmware now. I flashed the one u said the earliest. So Now I tried the one the other guy here showed me. didn't work either. it just gets stuck at samsung logo. I found a repair firmware for my model containing (pit, bl, ap, cp, csc and odin) I flashed all but odin fails "write error". I then tried odin v3.0.7 but then it got stuck while flashing the system image. I waited like 1 hour. nothing. tried it again. nothing it freezes on the same position. I then tried the same on the latest versions of odin v3.12.3, 3.12.7 and on 3.13.1 but it also freezes on system.img.ext4 image flashing..
Click to expand...
Click to collapse
afaik the "repair" fimeware is no better than flashing a stock ROM in one file...
its startng to sound like a hardware error, if it cant even write to the dvice theres really not many (probably any) options left.
ive purposely bricked a phone and recovered it (not recommended of course), ive never had or never saw as much effort youve put in to try and recover a phone...
stylemessiah said:
afaik the "repair" fimeware is no better than flashing a stock ROM in one file...
its startng to sound like a hardware error, if it cant even write to the dvice theres really not many (probably any) options left.
ive purposely bricked a phone and recovered it (not recommended of course), ive never had or never saw as much effort youve put in to try and recover a phone...
Click to expand...
Click to collapse
me neither.. can't believe this.. how can a phone be physically damaged by flashing? paid 70 bugs for a note 4 with a software issue.. as I often do. recovered dead phones from sony, xiaomi, wiko, asus, lg, huawei etc... adb, fastboot and u good to go. odin is killin me.. gonna sell it as bricked.
Cleared caches?
R0B3RTF1SH3R said:
Cleared caches?
Click to expand...
Click to collapse
HOW? If I can't boot into recovery mode?
Hello there,
I recently tried to get Android 10 onto my old phone. But i already got stuck on trying to root it. First I could not install new firmware because of FAP lock.
Then when I tried to get around the lock, I tried to root the phone with this tutorial. But Odin failed at hidden.img. Several times. And now I am stuck with "Firmware upgrade encountered an issue Select recovery mode in Kies".
I tried flashing with deleted hidden.img - it does not work. When I add an .md5 extension, Odin says binary invalid. When I remove the ".md5", Odin just crashes.
Any ideas?
If it is somehow important: I once rooted this device, but for some update or app, idk, i went back to normal, I dont really remember. I use Windows 10.
Thanks
tHr4sh3R said:
Hello there,
I recently tried to get Android 10 onto my old phone. But i already got stuck on trying to root it. First I could not install new firmware because of FAP lock.
Then when I tried to get around the lock, I tried to root the phone with this tutorial. But Odin failed at hidden.img. Several times. And now I am stuck with "Firmware upgrade encountered an issue Select recovery mode in Kies".
I tried flashing with deleted hidden.img - it does not work. When I add an .md5 extension, Odin says binary invalid. When I remove the ".md5", Odin just crashes.
Any ideas?
If it is somehow important: I once rooted this device, but for some update or app, idk, i went back to normal, I dont really remember. I use Windows 10.
Thanks
Click to expand...
Click to collapse
there is no Android 10 available for this phone
2gg1 said:
there is no Android 10 available for this phone
Click to expand...
Click to collapse
Well thank you, but that not helping with the issue that i cannot flash my phone with stock rom via odin.
tHr4sh3R said:
Well thank you, but that not helping with the issue that i cannot flash my phone with stock rom via odin.
Click to expand...
Click to collapse
So you have download the samsung drivers? Unzipped the file with result of a .md5 file? connected your phone to the pc with download mode? And then putted the file on the AP section? And clicked start?
Everything i just mentioned (except the .md5) can you find on HighOnAndroid website. Try to get the odin from there.
Please reply if it worked
2gg1 said:
So you have download the samsung drivers? Unzipped the file with result of a .md5 file? connected your phone to the pc with download mode? And then putted the file on the AP section? And clicked start?
Everything i just mentioned (except the .md5) can you find on HighOnAndroid website. Try to get the odin from there.
Please reply if it worked
Click to expand...
Click to collapse
Well yes, I already did all you described, but did not get it from HighOnAndroid (I also tried, but the "samsung drivers" are Malware which is blocked by Windows, so...).
I know how to flash a phone. It just does not work because of some weird Error with the hidden.img. I also saw a ton of other people trying to flash their phone with this Error, but their solutions do not work. So I need someone with another solution.
tHr4sh3R said:
Well yes, I already did all you described, but did not get it from HighOnAndroid (I also tried, but the "samsung drivers" are Malware which is blocked by Windows, so...).
I know how to flash a phone. It just does not work because of some weird Error with the hidden.img. I also saw a ton of other people trying to flash their phone with this Error, but their solutions do not work. So I need someone with another solution.
Click to expand...
Click to collapse
Try get the samsung drivers from samsungs official website
I once again tried it with these drivers. No change.
I just want to tell you, that I am no idiot and I know how to flash a phone. It just is a very specific problem, that occurs a lot apparently: https://www.youtube.com/results?search_query=flash+galaxy+hidden.img+stuck
The problem is, that the solutions posted on Youtube and other places do. not. work. As I explained in my starting post.