myTouch overheats when plugged in; won't charge - myTouch 3G, Magic General

When I plug in my phone to charge, the charging light does not come on. Within 2 or 3 minutes it becomes noticeably warm in the area below the battery. After about 10 minutes it gets very hot. No matter how long I leave it on, the battery does not charge.
I can turn the phone on while it is plugged in, but it will turn off within 30 seconds of unplugging.
I have tried 3 different wall chargers, 2 different USB cables on 5 different computers. I even bought a new battery. The result is the same every time.
Does anyone know what the problem might be and if it can be fixed. It is out of warranty, so I'm not worried about opening it up if there is a fix that involves getting dirty.
Thanks in advance!

Some more information that I've discovered since the first post:
I can charge the batteries as long as the phone doesn't overheat (in the fridge/freezer).
When I plug it in to USB, it will charge (as long as it doesn't overheat), but I can't connect it to ADB or mount the SD card. The computer doesn't really even recognize it most of the time. When it does it says "unrecognized device". FYI, I have used ADB many many times in the past, so I know it is set up correctly.
I'm not sure if this is useful information, but the SD card shows up as unformatted when I pull it out of the phone.
I realize that the problem is hardware, I just wish someone knew exactly what part of the phone was bad.

Related

X10i not turning on / charging

Hi guys,
Suddenly facing a strange problem since last night.
My x10i was running out of charge & i connected to the comp to charge while i was working. I noticed the charging speed was extremely low, so i restarted the phone to see if it would help. Did not.
Thought there is some problem with the cable, used a different cable as well, but no use.
The slow charging had stopped and eventually the phone died.
Tried connecting to the socket & charging, still no use.
The red led blinks when i connect the phone to a charger via the usb or the socket.
needless to say the phone does not even boot up now, obviously for no charge...
any ideas wat maybe wrong or wat i could do ?
please advice
Have you tried to let it charge for some time in off mode? As long as your battery is not dead, and the phone get the right voltage through the USB connector it should charge in an "emergency mode". This is a slow way of charging, but allows for charging without any electronic circuits to monitor it, it is not the same as the charging screen that usually displays when you connect the phone while it is powered off. Usually when a phone is completely discharged it needs to be connected at least 15 min, sometimes a lot longer, before the electronics kicks in, and starts the speedcharging.
My best advise would be to connect it to the mains charger, or a USB port you KNOW supplies power. Some laptops cut down on the powersupply to the USB ports when they run on battery. Let it be connected for a long time (several hours), and then try to power it on again.
If that does not help three things can be wrong
1. Somewhere the USB connection is broken, either in the cable or in the connector on your phone (or on the PC's connector, but that is less likely).
2. The battery is dead, modern batteries contain circuits that actually disables the battery when any given parameters gets outside the defined limits. This is to prevent the battery catching fire. On some batteries this renders the battery useless, and you need a new battery.
3.) The mainboard of your phone is dead, and hence nothing works, can be ruled out if you can borrow a battery from someone to test if your phone works then.
I hope a good and long charge can sort out your problem, that is the easiest fix, and it is free.
Hi O_K,
well, i have been charging (or trying to) the phone since it died last night.
i have used different chargers & different modes of charge (through the system & the wall socket) - no joy at all.
the LED blinks red a couple of times when connected.
Very occasionally, the SONY ERICSSON logo (startup) shows on the screen & it switches off again, back to the blinking.
So charging for a long time & through different chargers has not helped.
gonna try a different battery now to see if that can help.
Thanks for your response!
well, tried switching chargers & batteries.
The problem seems to be with the charging unit on the phone (USB)
with any charger or battery, wen connected the led blinks (like wen the phone is charging), but there is no charge happening.
eventually the phone dies, even if charging
any ideas?
There is a thread some where in this forum for fixing the same problem you have...I don't remember the exact name of the thread..if I find it I'll post the link here..Anyways what the guy did was
-Pull the battery out and connect the charger till the led turns green.
-put in the battery now and charge the phone...
and I think that was it.
Hope it helped..
EDIT: Found the link.
http://forum.xda-developers.com/showthread.php?t=944322

[Q] NC battery dead--can't get it to charge enough to boot

My Nook Color quit unexpectedly on my because of a dead battery. I have been charging it for a day with various non OEM chargers. Previously when something similar happened I could plug it into my computer and it would charge without booting, but it no longer does this. When it boots it takes too much battery and it quits before it boots. Help!
You need an OEM charger.
Could also try finding the shortest uUSB cable you have and let it charge from the PC overnight.
So is that trick to charging a Nook when the battery goes completely dead? I've let this happen a few times, and I've always found it difficult to get charging cause it starts to boot and shows a message about not enough power, and just hangs there, but doesn't apparently charge.
I've got mine in that state right now, and since I found this thread I plugged into the OEM charger using the OEM cable. With that combo, it didn't start up. Handy thing to know. Kind of annoying though because when I'm traveling I'd like to just take one cable along for phone and Nook. I'll just have to be sure and not kill the battery then.

[Q] Strange Battery/Charging Issue

EDIT: My model is I9505
Whilst on holidays, I took my phone out of my bag (when I knew it was getting close to flat) to find it not turning on. I assumed the battery was dead, but when I plugged it into the charger it didn't charge. I fiddled around a bit, and eventually got the vibration and charging light - but it kept turning off before the green battery came on saying charging. Being on holidays I didn't have my USB jig, or even external battery charger with me. I assumed it was a loose connection with the charging port - as every time I tried to plug it into charge it would only sporadically say that it was charging - but never get past the picture of the battery and the swirling icon (prior to the green battery coming up).
Upon arriving home, I got out my external charger, took out the battery, charged it for a few hours, then tried it. Again - it wouldn't turn on.
I then tried plugging the phone in again - but to the 800mA charging doc micro USB, insteead of the standard 2 amp. Straight away I get the charging picture, and the little graphic showing me the phone is about 1% charged. I leave it, the screen goes off. I come back 15mins later, the phone is RIDICULOUSLY hot, and the screen off. I unplug and replug to find the battery is still at about the same 1% level. I turn the phone on - it boots, shows 1/2% and then turns off as soon as I unplug it from the dock - even if I plug it straight into a 2 amp charger. I now decide that maybe the battery itself is the issue - and it's not holding charge. So I whiz out and buy two replacement batteries (MPJ ones, as they were fairly cheap - and this was just for the sake of finding the issue).
I charge one for about an hour on the external charger (the phone didn't turn on when I put the battery straight in). Then put it in - same deal. Nothing. I plug it into the dock micro-USB out to charge - again it comes up as charging, and shows at about 1%. I turn it on, and again am shown 1/2% charge, and again as soon as I unplug from the micro USB dock it turns itself off.
It is almost as if the phone isn't taking any power from batteries, and only direct from the power outlet itself. I'm unsure what could possibly have caused this. I can only think it may have been an external battery which I was using for a while on holidays (which had a 1amp micro USB out, that I was using to try and keep my phone charged). That is the only thing I have done different over this period (at least as far as I can recall!)
So basically - in short:
i) Phone won't turn on unless plugged in to a low amp charger (Computer USB, dock micro USB out etc)
ii) Even after charging batteries in external charger (two different external chargers have been tried) the phone is showing 1/2% battery
iii) The phone turns off a few seconds after I unplug it from the power source.
Any ideas!? I will take the phone to get repaired after Christmas (if they still repair it, as it's running a custom ROM).
BTW. a USB jig worked for the first time this afternoon - when I tried it not long after taking the phone off the dock. It's also worth noting that the phone is ridiculously hot when on the dock (around the camera/sim/micro SD area).
Googling there seem to be a few in similar situations.
This YouTube shows it
http://www.youtube.com/watch?v=U5B2By7fGII
Sent from my R821 using Tapatalk
abbaskip said:
Googling there seem to be a few in similar situations.
This YouTube shows it
http://www.youtube.com/watch?v=U5B2By7fGII
Sent from my R821 using Tapatalk
Click to expand...
Click to collapse
did you even try with a spare battery? can you check if your battery swollen? it might be the battery's fault
Repulsa said:
did you even try with a spare battery? can you check if your battery swollen? it might be the battery's fault
Click to expand...
Click to collapse
Hi, thanks for the response.
As mentioned in my first post, battery was what I thought was the issue at one stage, but I've tried two other batteries too. The original battery isn't swollen, but in any case I'm having the same issue with the other batteries.
I've tried charging them all on external charger before using them in the phone, and I get the same issues regardless of what I do.
It just seems strange that the phone switches on (now showing 0%) when plugged in, but not when unplugged.
And the batteries aren't being read properly, as they show 0% regardless of how long I pre-charge for.
Experimenting tonight, I've found that if I try to boot into recovery - even when plugged into dock, it dies before it even gets into recover.
Yet, if I boot the phone, I get to the main Android launcher/lockscreen before it dies...
Really has me baffled.
abbaskip said:
Experimenting tonight, I've found that if I try to boot into recovery - even when plugged into dock, it dies before it even gets into recover.
Yet, if I boot the phone, I get to the main Android launcher/lockscreen before it dies...
Really has me baffled.
Click to expand...
Click to collapse
Hello again, if you have any spare battery and its has 50 or 100% try to reflash the rom just to see the results. or try a different chargers and cables as well, If it all fails, i think you should send it to Samsung for the warranty. Software problems are somewhat easier to fix here than hardware, so your best option is to let Samsung handle it.
Repulsa said:
Hello again, if you have any spare battery and its has 50 or 100% try to reflash the rom just to see the results. or try a different chargers and cables as well, If it all fails, i think you should send it to Samsung for the warranty. Software problems are somewhat easier to fix here than hardware, so your best option is to let Samsung handle it.
Click to expand...
Click to collapse
Thanks again for your response, but you're clearly not reading what my issue is before making suggestions. As I have now said twice - I have tried three batteries, and batteries that I have charged for hours on an external charger before using. But they still come up at 0%. Not sure how you imagine I flash a ROM
It may be a matter of taking it to my dealer it seems. If anyone else has suggestions before I get to that (after Christmas) it'd be much appreciated
The batteries fully charged on external chargers and I'm still getting the same issues.
I'm hoping it's not kernel related. Can anyone confirm that if it makes it to download mode Werth a jig (but turns off after a few seconds) that this would be a hardware issue? It only turns on with the jig when it's straight off the charger though - so seems it's still not using the battery for power, almost residual power somewhere.
Sent from my R821 using Tapatalk
abbaskip said:
EDIT: My model is I9505
Whilst on holidays, I took my phone out of my bag (when I knew it was getting close to flat) to find it not turning on. I assumed the battery was dead, but when I plugged it into the charger it didn't charge. I fiddled around a bit, and eventually got the vibration and charging light - but it kept turning off before the green battery came on saying charging. Being on holidays I didn't have my USB jig, or even external battery charger with me. I assumed it was a loose connection with the charging port - as every time I tried to plug it into charge it would only sporadically say that it was charging - but never get past the picture of the battery and the swirling icon (prior to the green battery coming up).
Upon arriving home, I got out my external charger, took out the battery, charged it for a few hours, then tried it. Again - it wouldn't turn on.
I then tried plugging the phone in again - but to the 800mA charging doc micro USB, insteead of the standard 2 amp. Straight away I get the charging picture, and the little graphic showing me the phone is about 1% charged. I leave it, the screen goes off. I come back 15mins later, the phone is RIDICULOUSLY hot, and the screen off. I unplug and replug to find the battery is still at about the same 1% level. I turn the phone on - it boots, shows 1/2% and then turns off as soon as I unplug it from the dock - even if I plug it straight into a 2 amp charger. I now decide that maybe the battery itself is the issue - and it's not holding charge. So I whiz out and buy two replacement batteries (MPJ ones, as they were fairly cheap - and this was just for the sake of finding the issue).
I charge one for about an hour on the external charger (the phone didn't turn on when I put the battery straight in). Then put it in - same deal. Nothing. I plug it into the dock micro-USB out to charge - again it comes up as charging, and shows at about 1%. I turn it on, and again am shown 1/2% charge, and again as soon as I unplug from the micro USB dock it turns itself off.
It is almost as if the phone isn't taking any power from batteries, and only direct from the power outlet itself. I'm unsure what could possibly have caused this. I can only think it may have been an external battery which I was using for a while on holidays (which had a 1amp micro USB out, that I was using to try and keep my phone charged). That is the only thing I have done different over this period (at least as far as I can recall!)
So basically - in short:
i) Phone won't turn on unless plugged in to a low amp charger (Computer USB, dock micro USB out etc)
ii) Even after charging batteries in external charger (two different external chargers have been tried) the phone is showing 1/2% battery
iii) The phone turns off a few seconds after I unplug it from the power source.
Any ideas!? I will take the phone to get repaired after Christmas (if they still repair it, as it's running a custom ROM).
BTW. a USB jig worked for the first time this afternoon - when I tried it not long after taking the phone off the dock. It's also worth noting that the phone is ridiculously hot when on the dock (around the camera/sim/micro SD area).
Click to expand...
Click to collapse
In my view its a fault of charging IC . Since you have tried with replacing battery.
nishangrg said:
In my view its a fault of charging IC . Since you have tried with replacing battery.
Click to expand...
Click to collapse
Sorry, what is charging IC? If it was a charging fault, a fully charged battery would work wouldn't it?
So I took my phone to my SP - Telstra. The phone, being only about 6 months old, was still within warranty period. Not surprisingly, Telstra have said that as there is a Custom ROM on the phone, the warranty is voided. I stated that my understanding is that under Australian law, as it is a hardware fault, and not a fault caused by the ROM, the warranty still stands - however Telstra wouldn't budge and said I have 5 days to decide if I want to pay the $300+ for the repair.
What is my next course of action? Has anybody had a similar issue previously? Is the TIO the next port of call? Or should I be going to NSW Department of Fair Trading?
I'm sure I've read previously that phones are still covered under warranty after rooting etc, if it can be shown that it's a hardware fault, not a software fault. As the battery doesn't seem to be powering the phone, this clearly seems to be the case - esp. as it is the same in download mode and recovery mode.
Any help would be great. Please don't post pointing out that I rooted my phone so THAT's my own fault etc. These posts aren't helpful, I already have know that.
So I took my phone to my SP - Telstra. The phone, being only about 6 months old, was still within warranty period. Not surprisingly, Telstra have said that as there is a Custom ROM on the phone, the warranty is voided. I stated that my understanding is that under Australian law, as it is a hardware fault, and not a fault caused by the ROM, the warranty still stands - however Telstra wouldn't budge and said I have 5 days to decide if I want to pay the $300+ for the repair.
What is my next course of action? Has anybody had a similar issue previously? Is the TIO the next port of call? Or should I be going to NSW Department of Fair Trading?
I'm sure I've read previously that phones are still covered under warranty after rooting etc, if it can be shown that it's a hardware fault, not a software fault. As the battery doesn't seem to be powering the phone, this clearly seems to be the case - esp. as it is the same in download mode and recovery mode.
Any help would be great. Please don't post pointing out that I rooted my phone so THAT's my own fault etc. These posts aren't helpful, I already have know that.

Dead YD206

So YD206 about a month old. Was connected to official yota charger (via a magnetic usb cable), noticed the plug at the phone end getting quite hot. Phone now essentially dead, wont boot, doesn't seem to charge. We also realised the charger had come out of the wall socket. But the yotaphone light was intermittently flashing on the charger.
Whilst I am inclined to blame the magnetic charging cable, is it possible for current to flow in reverse from phone to charger and essentially discharge the phone battery below acceptable levels?
Any advice on rebooting it (can't remove the battery like I would on a Samsung) so whats the procedure?
Just a follow up charger not the issue, it crashed in use and the power button became non-responsive, with the screen off, and the e-ink display on but also unresponsive. Did not turn on when connected to a charger. However when I connected it to my pc it did register in device manager as MTP device, so I knew it was still alive. Removed the sim and held the power button down for 10 seconds then it rebooted.
Hope this helps anyone else with a similar problem.
Failing that it would probably have to be left to discharge (might take a while if nothing is running) then powered back on with charger attached.
I have similar problem. My phone got hot while not charging (about 15% of battery) and crashed. Then forced reboot (hold power button for about 10 seconds) helped while phone was connected to Yota charger, battery was dead, but phone booted (EPD on, did not check rest) and got to about 81%. After removing it from charger, same thing happened again, no luck with forced reboot this time. Phone was blazing hot and did not respond, then crashed again. No response after connecting charger or forced reboot. Any experience with this issue appreciated.
SuperTukan said:
I have similar problem. My phone got hot while not charging (about 15% of battery) and crashed. Then forced reboot (hold power button for about 10 seconds) helped while phone was connected to Yota charger, battery was dead, but phone booted (EPD on, did not check rest) and got to about 81%. After removing it from charger, same thing happened again, no luck with forced reboot this time. Phone was blazing hot and did not respond, then crashed again. No response after connecting charger or forced reboot. Any experience with this issue appreciated.
Click to expand...
Click to collapse
It seems a battery issue. Have your Yotaphone a valid warranty?
casaprocida said:
It seems a battery issue. Have your Yotaphone a valid warranty?
Click to expand...
Click to collapse
I am not sure about my warranty, bought it off AliExpress, I guess I could try to send it to manufacurer (i heard Russia provides repair service).
EDIT ( t + 2 days): I managed to start my Yota again. I connected it to computer and after about 5 minutes, magic happened and phone started all by itself. I will try to find out more, will update this as soon as I find something
Man, you are more lucky than me, I have a dead yotaphone lying around here. It also died after connecting it to a bad power source.
In my case it was the usb-port of a monitor.
When I checked the usb-port with a cable with a volt/amp display I saw that it was going on and off very quickly.
But so I would say be careful where you connect your yotaphone to, it does not seem to handle weird power sources all too well.
tomgaga said:
Man, you are more lucky than me, I have a dead yotaphone lying around here. It also died after connecting it to a bad power source.
In my case it was the usb-port of a monitor.
When I checked the usb-port with a cable with a volt/amp display I saw that it was going on and off very quickly.
But so I would say be careful where you connect your yotaphone to, it does not seem to handle weird power sources all too well.
Click to expand...
Click to collapse
I actually thought about burning charging circuitry a lot. I wonder, if you would be able to test wireless charging. With some luck, it is independent enough to not be affected by burning micro usb charging route (depends where high voltage safety is implemented). If this make any sense to you, please give this a try (I think IKEA is place to go, they should have working wireless chargers in their model setups) and report back. If I am wrong in any aspect, I'd appreciate any correction with explanation.
SuperTukan said:
I actually thought about burning charging circuitry a lot. I wonder, if you would be able to test wireless charging. With some luck, it is independent enough to not be affected by burning micro usb charging route (depends where high voltage safety is implemented). If this make any sense to you, please give this a try (I think IKEA is place to go, they should have working wireless chargers in their model setups) and report back. If I am wrong in any aspect, I'd appreciate any correction with explanation.
Click to expand...
Click to collapse
Sorry for the late reply, did not see the quote, but it does not work with wireless charging either. I think the battery still has a lot of charge too. Thing is that the Motherboard also gets hot after a while when I try to charge it. I'm pretty sure my motherboard is dead. But I have another Yotaphone now, so maybe in the future I will test with every separable part replaced.
I use the charger from my iphone. It works great, although with the yotacharger also works well. Attention that I have a YotaPhone YD201 with Russian base and european compilation. Like I said the Iphone charger works great and doesn't warm my Yotaphone 2 . It might be a solution for your problems with charging.

Axon 7 not charging sometimes

I've bought an Axon 7 last month (A2017 Chinese variant 128gb internal 4gb RAM). One day when my phone was shut down, I inserted the usb type c into the phone's port to charge it and it vibrated and turned on and showed the battery and the percentage but it was not actually charging and the percentage didn't go up even 1% and as I waited longer it actually discharged 1%. I didn't have this issue before that day so I pulled out the usb type c and inserted it in again and I saw that it was charging normally.
Later I figured out that the reason of that issue was that I unintentionally inserted the usb type c in the port in two pushes.(I mean I inserted half of the usb type c first and then push the other half into the port) So I checked it out and I observed that when my phone is shut down and I insert usb type c in one fell swoop then my Axon 7 starts charging normally ,but when I insert half of it first and wait for just a second and then push the other half and all of it into the port, the phone vibrates and turns on and shows the battery percentage but doesn't go up even 1% and if I wait longer it will even discharge 1%. FYI I 've tried several chargers,quick chargers,cables and the one that came in the box but the results are the same so if it is a real issue,the issue is with the software itself. I hope you guys can help me with this and tell me the reason and if yours have got the same issue. I would sincerely appreciate any replies.(my Axon 7 is still running 6.0.1 and A2017V2.1.1B07)
Aj-jss said:
when my phone was shut down, I inserted the usb type c into the phone's port to charge it and it vibrated and turned on and showed the battery and the percentage but it was not actually charging and the percentage didn't go up even 1% and as I waited longer it actually discharged 1%.
Click to expand...
Click to collapse
Does this happen when the phone is turned on? Maybe try Ampere if it does.
No when the phone's​ on, it doesn't happen. But when the phone is off and I insert usb c in two pushes and it starts discharging slowly, at that moment if I turn on the phone without pulling out the cable then it doesn't show any charging at all.

Categories

Resources