i jus changed the housing on my xda mini now it starts but nothing is on the screen, i hear the sound and bottons light up... ive check connector is in firmly however ive accidently broken the connector lock, does it need the lock in place for it to work...
if not what else can i try
also my flashing status light isnt fashing although fone is on (screen still not on) i get a white flash now and then on screen... and sometimes weird back lines..?
helo????
anyone here?
It is important that the flat cable has a good contact with the connector. I also broke the lock but placed a thin rigid plastic to keep the flat cable pressed down and then some tape on top to keep it in place.
nah didnt fix it, ah well another door stop..
the ribbon myt b broken....i think u'll need to replace display and da touchscreen too
try looking at ribbon cable carefully !
Like the topics states my 8125 will fade the screen every time I slide my keyboard open. It does it about halfway through the slide. Also practically non of the buttons on the front work anymore. I was told the ribbon cable may be loose, so I took it apart. I got all the way until the back of the screen seperates from the screen. I was pulling that apart and it didnt want to come so I just stoped in fear of breaking something. It was almost as if glue was holding a board on. Anyways I looked around as best I could and did not see anything. When I turned it back on it started right up but still fades out when slide open. Its been doing this for some time now and I just got back into the the cell phone thing rather then purchasing a new one. NBD ROM but the problem existed way before changing anything on the phone. Any help would be great. TIA
ttt anyone??
You will have to use a clipper preferably a plastic one to seperate the black back panel of the LCD housing,insert the clipper from the side and then run it along the entire panel till the six(i think) clamps unlock,then gently pry the back panel off taking care not to cut the flexi strip,that should do.It is most unlikely that it is a software issue,85% its a strip problem and 15% maybe because of the LCD.
Any chance you mean the ribbon cable when u say strip?
I have had the cable off and visualy looks ok.
any chance there is a replacement cable that I can purchace somewhere?
So I tried to do this: http://forum.xda-developers.com/showthread.php?t=376035
My screw was loose indeed. In fact is was so loose it fell out before I had opened it completely.
I tightened the screw, closed the cover, turned it on, and... nothing. Only the backlight of the screen, but the screen stays completely BLACK. Nothing. (I know the phone is working though, because if I hold the off button I'll hear the "boink" sound)
I tried this:
- With and without SIM card.
- With and without tightening the screw.
- With and without the power cord.
Mind you I have NEVER had this problem before.
What is going on here? Did I **** something up badly while opening this phone? If I did I am going to be super sad, so please, help me!
Anyone?
I basically have the same fault mate. My vibrator lock screw was loose and it made the phone rattle.
I opened it up and probably either tightened the screw up too much and killed something on the mainboard or 'pinched' the lcd flex ribbon ( rusty gold coloured thing- it plugs into the small white ribbon connector on the MB ) with the opening tool.
Anyway - the phone could take calls , it seems to be working ,although I have no display , and the keypad buttons are all lit up very brightly , what scuppered me was with the constant case opening I eventually managed to break the power microswitch off the MB and I now have to use the reset button to power the phone on.
I don't want to waste money buying a new lcd screen for a phone which might be terminally damaged due to a mainboard fault , anyone narrow these faults down more ?.
shameless bump.
BUMP !!
Im just fixing my LCD on my P3600 and have it in bits,
is the display connector definitely pushed all the way in?
Yeah m8 - AFAIK it is all the way in , I am certain that it is the flex ribbon connector that is broken.
For anyone else interested in this or that has the same problem - there is a program called ' my mobiler ' which can be found in the forum somewhere , using it will tell you all you need to know ;
i.e = if it is the phone itself that's broken , or it's a damaged display.
I cracked my aria screen pretty much right after I got it, Managed to get my hands on a new digitizer and replaced it. I found a quick walkthrough on Android forums. It helped but had a few points that could have been more succinct.
Posting here in case anyone needs.
Took me about an 1hr 30min the first time trying to figure it out on my own.
My additional comments are indicated by **.
I put some addendums to @Jcawesome's steps...
( http://androidforums.com/1211507-post42.html )
1. Remove backcover
2. Remove Battery, sim chip, and memory card
3. Unscrew the top two screws (meaning the end farthest from the memory card.)
4. Using a flat plastic wedge, (I used the one that came from my ebay order, it looks like the blue tool in this pic )
5. Carefully pull off the parts at the top being very cautious not to break anything. (Do not pull the circuit board out, only lift the end closest to the edge of the phone)
** there are two pieces to pull off....with the phone laying flat (screen down and the top facing away from you) a larger yellow piece with an attached back speaker comes out towards you. a second piece pulls up (north as if on a map)... but becareful because there is a bunch of tape and tackiness all throughout this thing (literally I felt it was held together by tape). I actually pulled off the grill on front as well.
** the circuit board is kept attached near the top right. the element that is the power button snaps off. (there are two little dots just to the right of the speaker with what looks like blackish tape that connects to the circuit board... you can pop this off.
With that off, I could lift the circuit board about 30 degrees or so... I wasn't comfortable pulling it back any farther than that.
I did step 5 AFTER I got the screen off.
6. Using the flat plastic wedge again, push the wedge tool between the phone and the broken screen. (It will feel like you are breaking it but it is fine, it is held on by a sticky paste that will slowly give way)
** careful on this part... especially difficult depending on how your screen is cracked. but it is just a bunch of sticky tape that is keeping it attached.... I had to peel away the goo and connection near the top sensitive areas as my ear piece speaker came off with the goo.
7. Disconnect the connecter from the old digitizer to the new one and remove the old digitizer.
**I used a small little tweezer and sneaked it in underneath the circuit board to pull the digitizer connection out.... a little difficult to push back in, but just took some patience.
8. Being careful not to put fingerprints on any exposed surface of either the phone lcd or the replace screen, place the new digitizer in the exact spot of the old one.
** have some lint free microfiber cloth handy and perhaps some screen cleaner.... I spent about 15 minutes cleaning the lcd screen before laying the replacement digitizer back on.
I actually did step 9 before step 8.
9. Connect the connecter from the new digitizer to the board, be careful not to pull the circuit board out and do not scratch the board.
10. You may want to use some glue to hold the new screen on, hopefully this will not happen again. My phone still had enough of the sticky paste left to hold the new screen fine.
** I agree... the first time you replace it will be fine.... afterwards tho, I can see it running out of tackiness.....
11. Put the phone back together in reverse order.
12. Turn it one and everything should be working again.
** in a nut shell
1) take out two screws
2) detach two yellow shell pieces
3) unhook a latch that is the power button
4) pry off the screen
5) lift the circuit board approx 30 degrees.
6) detach digitizer connection from underneath using tweezer
7) replace digitizer connection, return circuit board flat
8)position digitizer and press down to adhere
9)replace two plastic yellow shell pieces
10) screw it back together
done.
let me know if you have any questions.=)
enjoy your "brand" new aria.
dude,, this is a PITA,, I did,, was about 1hour, the hardest part,, is to not put the fingers on the LCD and cleaning the new screen..... dust particles everywhere... and at the end still got one...
Sorry eortizr, If I made it seem easier than it was. I spent quite a while cleaning the lcd screen when I replaced the digitizer... I don't think it's possible to change the digitizer without getting fingerprints on it though. But with some diligence and working in a clean area, I was able to keep all dust and finger prints out of the final product.
My wife dropped hers. Cracked up pretty good but still functional. Think I might just go ahead and pay the $100 and have someone who does it for a living do it.
I can totally see me trying DIY concentrating real hard dripping sweat all over it and ruining the MB. LOL
Replaced the screen today. Half way in I thought I definitely bit off more than I could chew. I got it done though. A couple of things I learned:
The digitizer unplugs away from you or toward the screen with the phone laying flat (screen down and the top facing away from you). I kept thinking i had to unplug it by pulling it north, toward the top of the phone.
I dropped and threw away both the front speaker and the very small rubber piece that covers the proximity sensor so... when I turned the phone on everything looked good, until I answered my phone. The screen went blank and I couldn't hear anything. I found the speaker and the proximity sensor cover and replaced them.
I would do it again, its worth saving $50 or so.
Thanks for the tutorial dreamflux.
I found the whole kit including the adhesive here: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=180643624141
This is the seller in case the sale ends and the link breaks: http://myworld.ebay.com/chinaphoneaccessories/?_trksid=p4340.l2559
I found a replacement digitizer from tmart dot com for $55, free shipping. Just search Aria on their site, you'll find it. Sorry, I can't seem to post links yet.
What was peculiar, was that it has only the HTC logo in the center, and no ATT logo. Looks nice and clean. They included plastic separator tools and torx drivers, though nothing in this phone uses torx. The site is a little shady, and while their headquartered in Hong Kong, it shipped from Brooklyn NY about 5 days after purchase, priority mail. The swap wasn't bad, but my only complaint is that the lights from the softkeys seem to shine up onto the screen, but you get used to it. It's probably because I didn't transfer the stickers over on the bottom of the digitizer.
Thanks for the directions ... I just replaced my digitizer. I had 2 major problems: 1) my power button doesn't work any longer (I'm going to take it apart and try to put it back together and see if that fixes it), and 2) you HAVE to use BLACK sticky stuff to seat the bottom of the digitizer - I used the clear stuff that came with the digitizer, and now I have tons of light bleeding into the LCD from the button backlights. I'm not sure what to do about the bleed ... I guess I'll have to tear it down again and put black stuff in ... damn.
That's the deal with that excess backlighting! I thought it was just a matter of the screen being misaligned. Terrible that I have to replace that black foam, it got shredded while I was dismantling the thing to replace the digitizer.
eortizr said:
dude,, this is a PITA,, I did,, was about 1hour, the hardest part,, is to not put the fingers on the LCD and cleaning the new screen..... dust particles everywhere... and at the end still got one...
Click to expand...
Click to collapse
its always suggested to work in a dust-free space but we all know that's virtually impossible.
I had a bit of fun with dust & fingerprints when replacing my LCD after getting my Aria, After a time or two of taking apart and being unsuccessful, I left it as is with one visible flake.
If you take a hot shower the steam in the air sticks to dust particles leaving no dust
Sent from my Liberty using XDA App
aria
use electrical tape to cover up the lighting that comes through the digitizer
use 3m double sided tape to hold digitizer to lcd
use rubber gloves to change screen to not get finger prints on it
dust906 said:
use electrical tape to cover up the lighting that comes through the digitizer
use 3m double sided tape to hold digitizer to lcd
use rubber gloves to change screen to not get finger prints on it
Click to expand...
Click to collapse
*Just to make sure I'm putting the electrical tape on correctly*
put the double sided tape on and then put the electrical tap (sticky side facing up) on top of the ds tape then apply the screen to the lcd
Thanks for the explanation dreamflux.. This, along with some youtube videos helped me out to change the digitizer, but patience is THE key...
Brought my phone with me to Cedar Point the other day. Survived the entire day....until I stopped at the bars on the way home. Got out of the car, forgetting I had my phone on my lap---shattered right by the track pad.
Just got my digitizer today for $22 on ebay (not bad) After 2 hours and a migraine later, everything came out great.
The only 2 things wrong now are the light from the softkeys bleeding onto the screen and out the sides (I'm just going to shut those lights off), and the trackpad sits a little lower than the screen now. Either I didn't align it right, or the glue isn't holding well. It's weird, if you press on the glass anound the trackpad, it wakes the phone (cm7 trackpad wake).
I only plan on using the phone for a few more months, so I'm happy with the results.
Uhhggg, did the replacement on my son's Aria. It wasn't so bad, but now the LCD screen doesn't light.
I get the vibration when you first hit the power button. Is this correct? I'm not too familiar with the phone.
Rececked the connector for the LCD and it seems to be snapped in.
brivette007 said:
Brought my phone with me to Cedar Point the other day. Survived the entire day....until I stopped at the bars on the way home. Got out of the car, forgetting I had my phone on my lap---shattered right by the track pad.
Just got my digitizer today for $22 on ebay (not bad) After 2 hours and a migraine later, everything came out great.
The only 2 things wrong now are the light from the softkeys bleeding onto the screen and out the sides (I'm just going to shut those lights off), and the trackpad sits a little lower than the screen now. Either I didn't align it right, or the glue isn't holding well. It's weird, if you press on the glass anound the trackpad, it wakes the phone (cm7 trackpad wake).
I only plan on using the phone for a few more months, so I'm happy with the results.
Click to expand...
Click to collapse
did you have any problems with the digitizer responsivenes or something like that? I'm need one and curious about the quality of the cheap digitizers in ebay.
so I replaced my friends screen and now the phone turns on, has sound, vibrates, but just doesnt turn the screen on... the light sensor works and all, and if I call it, it rings and everything, just the screen won't turn on it stays black... I've checked the 2 ribbons and everything is fine, anyone have a suggestion..??
jdmsohc22 said:
so I replaced my friends screen and now the phone turns on, has sound, vibrates, but just doesnt turn the screen on... the light sensor works and all, and if I call it, it rings and everything, just the screen won't turn on it stays black... I've checked the 2 ribbons and everything is fine, anyone have a suggestion..??
Click to expand...
Click to collapse
so what I meant was the digitizer turns on, but it is just a dark lit screen, no visual anything going on.. If i call it from another phone it will ring, but when i swipe right to left to answer and press around where the answer button is it doesn't respond either, just rings and rings... anyways just wanted to elaborate a little more..
---------- Post added at 02:28 AM ---------- Previous post was at 02:08 AM ----------
msailer said:
Uhhggg, did the replacement on my son's Aria. It wasn't so bad, but now the LCD screen doesn't light.
I get the vibration when you first hit the power button. Is this correct? I'm not too familiar with the phone.
Rececked the connector for the LCD and it seems to be snapped in.
Click to expand...
Click to collapse
same thing is happening with me as well..
^^^^ Soooooo.....I got the same thing on my wife phone, the BLACK SCREEN. I did my homework and read and watched videos on how to replace the digitizer. I was in a steamy room with all my tools from work with pre-cut electrical and .005" double sticky tape. im a mechanical assembler. I did everything to the tee and was very carefull. i think i got a bunk one from china. I bought mine for $19 from china. It had at&t logo and everything. you get what you pay for? So I've got to pay now $50 for a replacement phone through ins. Not bad because before i made the claim i thought the replacement was $150. Anyways just a heads up. Now i got a phone of spare parts Whats cool is that i get to root her phone all over again. So if anyone here has had the black screen. let me know what happened next with your situation. Did you fix it? replaced it with another one? thanks
I'm hoping somebody with some knowledge of the HD2's innards can help me...
My vibration stopped working on my HD2. I found the plastic LED flash cover to be 'pushed in' (with the help of a couple xda threads I dug up). Others said it was an easy fix: Open the case and push that piece of plastic back into place.
I opened up the case to correct it. But after putting it back together not only does vibrate not work, but the volume keys, speakers (both earpiece and speakerphone), flash, notification led, and camera all don't work.
I obviously screwed something up, but I have no clue what it could have been. I was very careful. One thing I'll note is that when I pulled the case apart, the plastic volume rocker went flying. When putting the phone back together I got it back into place so that I THOUGHT it should work (it was seated properly and felt "clicky" for up/down movements.
But clearly wasn't just the volume rocker that was affected. It doesn't seem that I pulled anything else loose or anything like that...
But no luck, all that I listed above is non functional, and what I'm left with is a glorified 3.5 in tablet
Any ideas?? Thanks in advance!!!
Snapped a couple quick pics which may help:
http://i50.tinypic.com/mmsa36.jpg
http://i47.tinypic.com/sl1kdx.jpg
Unfortunately when comparing these to other pictures of the inside of the HD2 that I found online, I fail to see any differences, or anything I could have inadvertently screwed up.
Most likely you screwed up(or disconnected from motherboard) somehow your main flexboard, but your picture are not usable for this, you should take off your motherboard+main flexboard from chassis to have a full view!
You probobly just disconnected a small cable. I have no idea of the HD2 innards but did multiple repairs of small stuffs and the flat cables hold in place by a plastic clicker pull out easily - just reopen and check them all, you should be fine.
Thanks for the input! I figured it's something like that, just one small cable. But I didn't even take off the board at all... The pictures show the full extent of the disassembly... Do we still think it's necessary to disassemble it further?
I checked all visible connections, but yeah, maybe I somehow yanked out something that is NOT visible. I'll try to check again today... In the meantime, any more ideas from anyone else? Thanks!
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Have u tried starting up the phone without the backing? I had this issue when I painted my housing the led cover was stopping the motor from spinning but if i took out the backing it works. So I just trimmed the led cover and now it works.
Mister B said:
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Click to expand...
Click to collapse
I'm nooby with regard to this stuff; I only attempted the repair since I read in a couple other threads about multiple self-proclaimed non-super-tech savvy people were able to open it up and move the plastic LED cover for an easy fix.
So what exactly am I looking for with regard to the main-flex? Where is it? I thought I wouldn't really see that unless I removed the board which I haven't done... is it still possible I knocked it loose or damaged it? I didn't think that would be possible since I ONLY removed the back cover (though it does take a slightly uncomfortable amount of force to do so, so I guess anything can happen...).
If not the main flex cable, is there anything else specific to look at which may be disconnected? It seems to be all the stuff at the top of the phone that fails to work (camera, speakers, vibration, flash, volume keys). While the stuff on the bottom (other hardware buttons, charging jack, headphone jack, etc).
THanks!
I have given up. After being stumped briefly how to hard reset the device without the volume keys working (I have Android installed), I was able to do it via ADB from the Android dev kit.
To ebay I go...