Database Users

where can i get a new digitzer for my 8525

used windex on my screen and the digitizer went bad.
any recommendations on where to purchase a new one?
thanks pogo

on eBay! ...

cnn.cn 7.99$ I have to order one this week, just have to get around to it.

cnn.cn BINGO !
:d :d :d :d :d :d :d :d :d :d

8525 Digitizer Installation...
Hello,
I have an 8525 with a broken digitizer (LCD OK). I replaced the whole unit with a new combined LCD/Digitizer. It is a pretty straightforward repair. It took me all of about 15 minutes (you just need a #6 torx and a jeweler's phillips).
Just in case this happens again, I purchased a new digitizer (only). I want to remove the old digitizer from the LCD screen and replace it with the new one. The problem is: the digitizer ribbon cable is attached to the LCD screen, possibly soldered but I can't tell. Are there any instructions anywhere regarding the digitizer removal and installation?
Thanks

Im new to all this whats the digitizer exactly?

The digitizer is the top portion of the screen. It's what registers your stylus' contact on the screen. It lays on top of the LCD and it looks like 1 piece, but its actually two. And for those wanting to know if the digitizer is soldered, the answer is no. It's held in place with tape, but it is easier to just replace the combo instead of just the digitizer. Most often then not, when removing the damaged digitizer, it will crack and may possibly damage the lcd, or so I've read. I just recently cracked my lcd, so i got a combo and switched it out, just to have a scratch on the digitizer the following day. That's life. Waiting for my next new combo to come in the mail.

You'd be better replacing both the lcd and digitzer as 1 unit than try to unglue and reglue the digitizer onto your screen. A lot of hair pulling and screaming involved and no guarantees it'll work. For the $100Aud I'd just replace the lot in one hit. As markus1959 said its a 15 minute job but stuffing around with just the digitizer is a major hassle. Even Mike Channon (he's the hermes hardware guru) advises against that unless you're really into pain and frustration....
Cheers...

Hi,
from where do you all get a new LCD (+ digitizer).
My LCD is cracked (digitizer OK) so I need replacement.
I live in Switzerland and I can not find a shop with a reasonable price.

Replace Touch screen

Hello,
i have a cigarette dropped on my touch screen and want a replacement screen for it. Where can i buy one ?
i have bought this: http://mobile.brando.com/htc-touch-diamond-2-replacement-lcd-display_p04369c0696d088.html
but this is the lcd, not the touch screen ???

you have to buy digitizer something like that

prdic said:
you have to buy digitizer something like that
Click to expand...
Click to collapse
Exactly....But the touch screen digitizer is very hard to replace. I have taken mine apart only to find it near impossible to replace without damaging the rest of the phone. I only wanted to replace the housing, but you must replace the housing and digitizer together.
NOTE: If you attempt this, remember to remove the stickers over the little ribbon cables before sliding them out. Found that one out the hard way.
Your best bet would be to send it to hTc for a repair. I really wouldn't risk it if I were you... I only did because I have trianing in electronics.

oh ok, any ideas of the costs when sending it to a repair center ?

The repair cost me 157 euros for replacing the housing and touchscreen sensor.

And if you want to prevent further costs with such issues .... uh ... quit smoking

Finally fixed by Touch HD!!

To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.

Congratulations!!

mrmomoman said:
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Click to expand...
Click to collapse
How did you attach the digitizer to the LCD? Aren't they glued together or something like that?
Because that's where my attempt went terribly wrong: Instead of getting the digitizer off my LCD, I broke my LCD... I bought a new complete screen unit because I didn't know how the LCD is attached to the digitizer!

The digitizer is semi-glued to the LCD panel which sits on the back along with the thin metal cover. The digitizer has a thin flat connector that connects to the back of the main board on the bottom. I slowly pryed off the LCD(grayish white in color) from the back of the Digitizer. It came off and I aligned it back up with the new digitizer and the glue residue left over from the LCD adhered to the rear of the new Digitizer. the tricky part is the thin connectors that attach to the mainboard. You have to get a pair of tweezers to pull it from the flat connector. When you get the digitizer you will see the new connector. Attaching that and the prying of the LCD was the hard part.
I read somewhere some guy said he broke the LCD but in truth it wasn't the LCD that he broke. He pryed apart the 3 layers of the Digitizer and thought he ruined the LCD. I thought the same thing orignally then I when the whole LCD/Digitizer was in my hand I was looking realized that the LCD was the grayish/white panel on the back. One can easily peel away the top 2 layers of the digitizer and would think that it could be the LCD they ruined.
I hope that makes sense. It was the first time I did this and I didn't see the video where someone removed the Screen. I only saw the Russian guy who didn't finish the job because he was stuck at the end. I just figured it out the hard way.
Also the T6 works but I think a t5 would be better. I only had a T6 and it did the job.
I am so glad I wore gloves or I would have had some major finger prints all over the unit

mrmomoman said:
The digitizer is semi-glued to the LCD panel which sits on the back along with the thin metal cover. The digitizer has a thin flat connector that connects to the back of the main board on the bottom. I slowly pryed off the LCD(grayish white in color) from the back of the Digitizer. It came off and I aligned it back up with the new digitizer and the glue residue left over from the LCD adhered to the rear of the new Digitizer. the tricky part is the thin connectors that attach to the mainboard. You have to get a pair of tweezers to pull it from the flat connector. When you get the digitizer you will see the new connector. Attaching that and the prying of the LCD was the hard part.
I read somewhere some guy said he broke the LCD but in truth it wasn't the LCD that he broke. He pryed apart the 3 layers of the Digitizer and thought he ruined the LCD. I thought the same thing orignally then I when the whole LCD/Digitizer was in my hand I was looking realized that the LCD was the grayish/white panel on the back. One can easily peel away the top 2 layers of the digitizer and would think that it could be the LCD they ruined.
I hope that makes sense. It was the first time I did this and I didn't see the video where someone removed the Screen. I only saw the Russian guy who didn't finish the job because he was stuck at the end. I just figured it out the hard way.
Also the T6 works but I think a t5 would be better. I only had a T6 and it did the job.
I am so glad I wore gloves or I would have had some major finger prints all over the unit
Click to expand...
Click to collapse
Thank you for your explanation! But I'm still not going to attempt this on my own any time soon... We'll see... Maybe I'll change my mind if my digitizer is broken or scratched...

Respect man! You mentioned that you bought digitizer for $17. Is it possible to buy mainboard for Touch HD from that place? Can you please advise where I can get it. And how much it will be?

Got to love a bit of micro-electronics DIY!

This just shows that HTC are taking people for a ride - there are a lot of people who would have just paid the price they stated. As you've only replaced the digitizer, shows they were taking the mick with the LCD and otherwise, what are these "internals" that HTC said it needed I wonder...??

Just replaced the digitizer on my HD and it took about 1.5hrs. As long as you're very careful, it's not that hard at all.
Make sure you have the Service Manual though as it was a great help.

Have you got the link for the service manual?
Ive just had to order a Digitizer as my phone has decided it doesnt want to work anymore (6 months to go on contract too ffs).
Managed to get one from a UK seller with tools for £17 so im happy.

KickAssMoves said:
Have you got the link for the service manual?
Click to expand...
Click to collapse
It's in the wiki.

WelshWarior said:
Just replaced the digitizer on my HD and it took about 1.5hrs. As long as you're very careful, it's not that hard at all.
Make sure you have the Service Manual though as it was a great help.
Click to expand...
Click to collapse
Hi:
How did you get the digitizer separated from the LCD?
I was thinking of putting two suction cups (1 on the back of the LCD, and the other on the front of the digitizer), heating everything up for a couple of minutes with a heat gun, and then pulling them apart holding the suction cups.
Does that make sense?
Thanks.

mrmomoman said:
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Click to expand...
Click to collapse
i just had mines fixed called them told them wat i did that i found an outer sreen and tryed to replace it myself and completely destroyed the lil black screen inside of the 4screens put together and that my device software was moded now i had 469 out going and another 469 incoming calls they only charged me 113 but wen we first talked about it they did say about 350 until they see the device and then they will call you before the repair it but the did wipe out my device and reinstalled the oem rom they also gave me a full new body and zero'ed out the incoming and out going calls which never changest unless they put in a new mother board which makes my phone brand new

sorry if ive missed it, but how do you get the lcd and digi out from the black outer casing frame to start with ??, from what i can see it comes out by somehow pushing from the inside to make it pop out ?? could someone please explain a little bit more on how to do this, ill try and make a vid of me getting it out as i have yet to find one that shows this, also my screen has that wierd pearl essance look to it?? does this mean its the digitiser.
Cheers
Mike

pickie said:
sorry if ive missed it, but how do you get the lcd and digi out from the black outer casing frame to start with ??, from what i can see it comes out by somehow pushing from the inside to make it pop out ?? could someone please explain a little bit more on how to do this, ill try and make a vid of me getting it out as i have yet to find one that shows this, also my screen has that wierd pearl essance look to it?? does this mean its the digitiser.
Cheers
Mike
Click to expand...
Click to collapse
Mine had that pearl essence look to it for a good few months before it broke, not that im sure that has anything to do with it.
Just awaiting the delivery of the digitizer and hopefully I can repair it.

yeh mine had the pearl effect for a long time prior to it dyeing

ive followed the service manual and the video of the guy who gets stuck near the end, but how do you g et the screen out of the casing to get to the digitizer?
Its one hell of atight fit and i cant see anything o bvious.
Help

Hi Guys
Sorry about the late replies - had phoneline probs!!
Assuming you followed the instructions in the Service Manual to take the rest of the phone apart, you've just gotta be VERY careful and push the screen out from the back (where the Circuit Boards where) of the plastic frame. At first, it feels like it's not budging but be patient and it WILL start to push away.
It seems to be held in with some sort of hot glue or maybe a contact sort of adhesive and I didn't try it but some heat from something like a hair dryer may make the job easier.
Many people have cracked their LCD screen during the repair but as long as you're careful not to bend the screen too much when taking it out, you'll be fine.
I peeled the 3 layers (outer glass ones and then the Digitizer itself) off the LCD whilst removing it.
Good luck - it's really not that hard. Any more questions - just ask ;-)

ive got the phone apart to the point of the service manual/video
which part of the back do you push out? doesnt look obvious as to whats attached and what isnt

Once you get to the last stage (I thinks it's the Speaker Removal) you simply push on the metal protector of the LCD from the back. You will see small holes in the plastic of the back of the frame where you can push something blunt through and push very lightly on the LCD to push it out.
If I remember correctly, at the bottom of the phone where the circuit board with the vibrator and microphone on it was sitting, there is quite a large opening with the metal backing of the LCD visible through it. I started pushing there and gently went all around the phone in the various small holes dotted around it.
As I said above, it won't feel like it's working at first but it will - just be patient and not too heavy handed!

My HTC HD2 Disassembled to the LCD

I posted in another thread about the issue of digitizer being glued to lcd. I had more pics to show, and decided disassembled pics are useful to all! So new thread for full set! If you want more I can get more! If I get enough questions I might make a tutorial for dis assembly.
General Disassembly
Slideshow:
http://img96.imageshack.us/slideshow/webplayer.php?id=htchd2wificam2.jpg
Desoldered Digitizer Pics
Slideshow:
http://img705.imageshack.us/slideshow/webplayer.php?id=htchd2desolderedtermina.jpg
Digitizer Removal w/ Razor
Slideshow:
http://img696.imageshack.us/slideshow/webplayer.php?id=htchd2digioffrazor.jpg
ENJOY!
This really is a great phone!

can't see anything. please use a different host

brandi said:
can't see anything. please use a different host
Click to expand...
Click to collapse
Fixed problem!

OH NO!! what HAVE U done!!!

I know...The horror...I haven't re-assembled to see if still working...HA!
I disassembled because of a cracked digitizer.

looks like a fur or "plastic" carpet, hope you don't end up with ESD related problems
ESD as in ElectroStatic Discharge ^^

Phone still works just fine.
If anybody knows how to un-solder the digitizer away from the lcd, help would be appreciated!

New images added.
Next up:
digitizer/lcd separation

any updates?

Have you managed to fix it yet?
We all want you to succeed so we can operate on our own cracked ones! Maybe you need the "unglue" chemical - you know, like superglue has an antiglue for reversing it's stickiness. If you could find out what glue bonded it, then a specialist adhesive supplier probably knows how to reverse it.

I'm sure you'll like this (if it isn't posted here before...)
http://pocketnow.com/hardware-1/official-htc-hd2-disassembly-assembly-training-videos-leaked

Still not clear, has he finally removed the lcd on that video from the digitizer? to me it looks they're still cemented

tamas970 said:
Still not clear, has he finally removed the lcd from the digitizer? to me it looks they're still cemented
Click to expand...
Click to collapse
Well if they're cemented (hopefully with some hyper-glue), thats a GOOD thing. Then this will be (hopefully) my first device with NO dust under the glass.
Don't you people have insurances on your devices? Talk to the ensurance company and you will get a new device for a small excess - that is, if it's beyond repair

Halle said:
Well if they're cemented (hopefully with some hyper-glue), thats a GOOD thing. Then this will be (hopefully) my first device with NO dust under the glass.
Click to expand...
Click to collapse
its not ... I have dust under the displayglass.

Floatheavy, and everyone else.
I'm currently on my second HD2, first suffered a hairline crack on the digitizer and it went COMPLETELY unresponsive. After getting the second, I had nothing to loose and disassembled the first. I got everthing apart up to the LCM, this module has everything (the glass digitizer, the LCD and the backlight) all cemented together. As I took the phone apart, priodically I would test that it still worked - everything except the digitizer. When I tried to separate the digitizer from the LCD and baclight I ended up tearing the layers of the LCD apart, now one layer is still glued to the digitizer and one is still glued to the backlight. I have yet to see how this can safely come apart and untill I can buy the LCD the phone is totaly screwed. I think one has to purchase an entire LCM and not just the digitizer.
For those that want to try separating the digitizer - BEWARE, noone seems to have found the secret yet! If I manage to discover something new I'll post.

Yeah. I tried the heat method to separate the digi from the LCD...
No luck
It seems it is more than the simple adhesive broken down by heat.
To get the bezel away from the LCM you can use heat to make easier, but to get the digitizer away from the LCD itself remains a mystery to me.
Anybody get any other results?

OKAY..
Pics updated again...
I was able to get the digitizer apart from the LCD, using a razor.

for separate lcd and digitizer
For separate lcd and digitizer, I used nylo fisher string... and it work good... just right my problem is how to past new one ? neopren glue ?

Honestly, I plan on just adding a dot of super glue to each corner.
I believe most phone adhesives are a sylicon based glue.

It`s almost impossible to un-solder the digitizer away from the lcd, i have succeeded a few times whit hot air and very sharp cutter, but still broke 2 screens from 5...it has to be a solution for this...anyway 3 phones from 5 its not the best rate...

My HD2 LCD screen broken -- Help!!

My LCD screeb broken yesterday. I have tmobile HTC HD2.But my touchscreen works fine.
Do I need to purchase this one
http://cgi.ebay.com/OEM-HTC-HD2-T858...#ht_2748wt_698
or
http://cgi.ebay.com/T-MOBILE-HTC-HD2...ht_1845wt_1014
Do I need to solder something or is just an easy fix?
Please let me know.
Thanks

Mine too
The links to the Ebay sale you posted are no longer valid.
My screen is broken also, just the touch sensitive glass (digitizer). The LCD is still in tact.
From what I understand the digitizer is harder to replace than the entire screen (digitizer+LCD) because the LCD is glued to the digitizer. There's a video on YouTube someone posted demoing the process.
http://www.globaldirectparts.com/HTC-T-Mobile-HD2-Digitizer-p/htc733745.htm
Has the digitizer for only $57 USD, but you have to order 3 at at time. If we can find someone else that's interested, then maybe we can go in and get one if that's all that you need also.
Cyph

I have done the digitizer repair, not exactly what I would call a fun time.
Easy to mess up your phone, need to make your own glue or double sided tape (to hold digitizer/lcd/frame together), about 4 little tiny wires that need to be placed correctly when putting the phone back together.
Thankfully the US HD2 does not require soldering the digitizer's connector to the lcd (the european one does), however again this is not a repair job for the feinthearted.
After all was said and done and the digitizer was repaired, the new one had the rainbow/oil effect when under a fluorescent light source, don't know if it is due to me using the wrong digitizer or what, but it did not look good. I had the same issue with a altell touch pro 1 that I purchased on ebay, it annoyed me then and it's back with a vengance.
Have fun, be very meticulous and watch the HD2 dissembler videos about 5 times before you unscrew one screw.