Hi, I'm trying to flash WP7 on my tmobile HD2. I had HSPL3, the 2.15 ver radio. After installing MAGLDR 1.2, when I boot up holding the power button down, the phone automatically boots android from SD. (I had it on my SD card before but didn't think it would be a problem).
Anyone know how to fix this?
It just says Booting Android from SD,
Android load etc
load z image,,
stops at GO GO GO! then just hangs. Hope I didn't screw up.. thought I was following the directions carefully.
You mean magldr 1.12?
"services"-->"Bootsettings"-->"Boot source"
Figured it out. Wasn't holding the power button down early enough. Thanks!
akollgaard said:
Figured it out. Wasn't holding the power button down early enough. Thanks!
Click to expand...
Click to collapse
Easier to enter the boot menu, is to hold the power button to startup your phone and hold the button until the menu appears ^^
Related
after flash andriod rom use maglrd 1.11 , i cant boot in to tri color bootloader , i try hold down vol button and power button but alway boot in to maglrd , please help , i need find out how to boot in to bootloader ?
Power off your device and hold "Volume Down" and Power on the device till u get the tricolour screen.
i try that but just boot in to maglrd not bootloader
I've tested it yet and it works for me!??
- Shut down ur device
- press the volume down button (hold down all the time)
- short tap on the power button and release it (still holding volume down)
still the same boot in to maglrd
I think you're holding the power button too long.
Hold down the volume down and press the Power On and release it while still
holding the volume down.
Works for me.
i just tap the power button
same here
I got the same problem I was going to flash a new radio and start over with MAGLDR with a new nand because the call key isn't working since i started using namd versions, last night i spent like two hours trying to get my phone in Bootloader Mode with no luck
hope some one can help
Vol down and power. odds are your not holding it right. If it dont work, then your stuck with Magldr.
Why are you even holding the power button?
To get to the RGB Bootloader:
Turn off Device
Hold Volume Down Button
Turn on Device - DO NOT HOLD the POWER BUTTON
LiFE1688 said:
Why are you even holding the power button?
To get to the RGB Bootloader:
Turn off Device
Hold Volume Down Button
Turn on Device - DO NOT HOLD the POWER BUTTON
Click to expand...
Click to collapse
That doesn't work for me and i can't have a hard reset neither.
I always go back to android.
I just can change nandroid with magldr 1.10 : i can't come back to winmo : android works well but I need some winmo programs.
You sure you doing it right?
You release the power button when the HD2 vibrates but you still hold on to the Volume Down button.
I play with this HD2 all the time, switching from WinMO6.5 to Android SD, and Android NAND, as well as Clockwork Recovery NAND.
If I want SPL3.03, I go into Recovery Mode with leoimg.nbh file.
When I want to go back to Android, I do recovery back to 1.66 to recover back to SPL 1.42 so I can flash back HSPL 2.08
Have not met an issue yet.
Yes i just tap the power button and still just go to magldr
yongh said:
Yes i just tap the power button and still just go to magldr
Click to expand...
Click to collapse
Do you even have HSPL installed???
Yes other why i cant flash to andriod la
Research more stuff
MAGLDR is not boot loader
Bootloader = phone off, volume down + power button
MAGLDR - Phone will be off + hit power - it will turn on in MAGDLR
P.S. If installed correctly
can someone please help me,i installed maglrd 1.11 for install android, when
restart its come up to htc logo in white screen only i can go in to bootloader but nothing i can do,i installed hspl, i dont know wht to do now.
perhaps your volumedown button does'nt work properly.
Take the back off the phone,
take the battery out,
wait for a few seconds,
put the battery back into the phone,
leave the back off the phone, so that you can feel better that you press the volume down button correctly
press power button only once and very briefly
this should work, I had the same problem
Hello!
I'm having a problem during the installation of the clockwork recovery, tbh its one of the first steps but here we go
atm Im using MDJ's CyanogenMod 7 v. 2.6 and I would like to install the recovery but to do this I need to reach magldr which is not accessible due to the fact that I can't do anything except looking how my android autoboots ;/
every time I turn off the phone and hold the power button, it just boots to my android. I see magldr starting and booting my system, counting 123456, then gogogo but I cant do anything
help me
You need to keep that button pressed until you're really in the menu, you're probably releasing it too soon?
Are you keeping the power button down all the way thru the boot process, if you're not, keep holding it from power down til it reboots and keep holding it until it should switch to the mgldr options menu.
Sent from my HTC HD2 using XDA App
StephanV said:
You need to keep that button pressed until you're really in the menu, you're probably releasing it too soon?
Click to expand...
Click to collapse
oh my god, that was so easy
works
thank you very much!
once you get used to it, you'll find you only need to hold power from just at the end of the first bootscreen until the menu appears, about 4/5 seconds. Not all the way from power on, about 15 seconds.
How do I get into magldr again?
If I hold volume down and power on button, it goes to screen with 4 colors.
What do I do then? Already got all the addons such as hspl installed.
Hi, just hold the power button longer, also magdlr is shown on the device.
the_hd2_cracker said:
Hi, just hold the power button longer, also magdlr is shown on the device.
Click to expand...
Click to collapse
Did that, and nothing.
I do see magldr when starting it up normally though. It boots an old rom that I don't want.
Anyone at all?
So when the phone powers up, you're holding the power button, and the menu still doesn't show up? Well then, reinstall MAGLDR though the tri color screen then, it won't wipe your current android data, dun worry. Or you can task 29, install MAGLDR, then reinstall your android build.
Switch the phone on and keep holding the power button in until you get to the menu.
Kailkti said:
So when the phone powers up, you're holding the power button, and the menu still doesn't show up? Well then, reinstall MAGLDR though the tri color screen then, it won't wipe your current android data, dun worry. Or you can task 29, install MAGLDR, then reinstall your android build.
Click to expand...
Click to collapse
It does kinda show up though, for 3 seconds and then it will say go go go!
it's booting up a old rom though.
ClydeB1 said:
Switch the phone on and keep holding the power button in until you get to the menu.
Click to expand...
Click to collapse
This worked! thank you sir.
If you hold volume down and power on button you will enter bootloder (spl 2.08 )
If you switch off your device and switch it back on AND NOT LET GO OF THE POWER BUTTON, you will inter magldr menu.
You need to keep the power button pressed in until it boots into the menu, don't let it go until you see the menu options.
Edit: Ok, see you got it working.
Lawl that's hilarious. xD
I'm sorry, just found this funny. xD
Hi guys, I have searched and searched and searched but cannot get anything I've tried...
Essentially, I got an HD2 today, flashed HyperDroid and all was good, until I wanted to access CWM via the mgldr menu, I tried to access it but it just would not work. Holding the power button would just boot the phone, it displays some text that I cannot remember then '1234 GO GO GO!'
So instead I tried to boot into CWM from ROM Manager, but that didn't work either, it just booted the phone as usual.
So I did a task29, started all over again, flashed a different ROM and the same thing..
I really am lost, any help would be much appreciated.
no offence intended here
Task 29 wipes the phone,
put phone in bootloader, turn on holding volume down,
install magdlr, then the phone will only boot to magdlr, make sure you have appropriate radio to boot.
you should now only have Magdlr on the phone and nothing will boot and you can go through the process of installing cwm to get a android build up and running.
to access magdlr when you have a build be it android or wp7, turn the phone on when it vibrates press the power button and keep holding it down until the magdlr screen appears
Demon_man said:
to access magdlr when you have a build be it android or wp7, turn the phone on when it vibrates press the power button and keep holding it down until the magdlr screen appears
Click to expand...
Click to collapse
None taken, I guess I misread the instructions on all the other threads, I thought you just had to hold power until it booted into mgldr, not press it, release, then press again. Thanks mate!
Jake254 said:
None taken, I guess I misread the instructions on all the other threads, I thought you just had to hold power until it booted into mgldr, not press it, release, then press again. Thanks mate!
Click to expand...
Click to collapse
its just the way ive always got into magdlr but np hopefully u get sorted.
Long story short, I was attempting my second flash. I followed the steps before and everything was going fine. Now right before i open CWM to install android the MAGLDR ( which is version 1.13 ) gets stuck at "123456GOGOGO".
Now i thought maybe i would start my proccess over but I cannot acces the tricolor screen. I wasnt able to do this in the beginning of my proccess either, when i pulled up my HSPL program on my desktop my computer entered the tricolor screen on its own and I proceeded from there.
Basically i have looked around and have found some ways out of the GOGOGO problem, yet I cannot acces the Tricolor screen using hardware buttons so I am stuck. And its not a hardware issue. In MAGLDR the Vrockers work fine and before I did anything the rockers were working fine in Windows 6.5.
Any Ideas? I have a feeling i got a pretty nice paperweight now.
the normal way to enter the tricolor screen is to turn the phone off then hold the volume down button and momentarily hit the power button.
Also, To keep from getting to the 123456 GOGOGO hold the power button while it is booting normally and you will get to the MAGLDR menu and there you can go to the AD Recovery and flash a new rom.
hunterthehuman said:
Long story short, I was attempting my second flash. I followed the steps before and everything was going fine. Now right before i open CWM to install android the MAGLDR ( which is version 1.13 ) gets stuck at "123456GOGOGO".
Now i thought maybe i would start my proccess over but I cannot acces the tricolor screen. I wasnt able to do this in the beginning of my proccess either, when i pulled up my HSPL program on my desktop my computer entered the tricolor screen on its own and I proceeded from there.
Basically i have looked around and have found some ways out of the GOGOGO problem, yet I cannot acces the Tricolor screen using hardware buttons so I am stuck. And its not a hardware issue. In MAGLDR the Vrockers work fine and before I did anything the rockers were working fine in Windows 6.5.
Any Ideas? I have a feeling i got a pretty nice paperweight now.
Click to expand...
Click to collapse
pull your battery,
put it back in,
hold down volume and power button,
and theres your tricolor screen
True i know about to Volume Down and power key to enter Tricolor, but for some reason with my phone that does not access the Tricolor, tried it many times.
Holding the power button while it booted made no difference.
*******I followed these steps for flashing my rom:*****
First, you need your files!
HSPL4
MAGLDR 1.13
Clockworkmod Recovery
Download a ROM of your choice, I prefer Hyperdroid
Unzip only the first 3 files, and place the ROM zip on your SD card.
So, here we go!
Remember to back up all of your contacts and any data stored on the phone that you want to keep, because you will be wiping windows off ENTIRELY.
HSPL4-
Plug in your phone.
Right click the HSPL4 file and select "Run as Administrator"
Go through the screens, then when it's connecting to your phone your phone will go into bootloader (red, blue, and white screen)
Select HSPL 2.08 when it comes up, hit next. Let it work.
It'll popped up saying "We hacked it!", and you'll see it on your phone. Click yes, then ok and you're done with this step! Phone will restart.
MAGLDR 1.13-
After phone's restarted, go to the MAGLDR folder, right click "ROM Update Utility", and Run as Administrator.
Checkmark the necessary boxes to continue through steps. Then click "Update", then click next through screens.
Once it starts updating ROM image, it taks about 2 minutes. Then click finish.
Phone will reboot into MAGLDR.
Navigate MAGLDR using the volume up and down keys. Use the green button to select (you may have to click twice).
(At this part in the video I uploaded the ROM zip, I'm assuming you already loaded it though, so skipping on).
Flash Clockworkmod_150
Scroll down on MAGLDR to option 5 "USB Flasher". Don't select it yet.
On your computer, go to the Clockworkmod folder, right click the DAF file and run as administrator.
Click next until it gets to waiting for USB.
Now press the green button to put it in the mode.
Text will start to appear on the phone screen, and the Clockworkmod flasher will do its work.
Once done, click finish, and MAGLDR will reboot. It may say something like "kernel fail", it's normal, don't worry about it.
Scroll down to number 8 "AD Recovery", select it.
It'll say Go Go Go Go, and then you'll be in Clockworkmod Recovery!.
****************************************************
BUT! at this point i get stuck in GOGOGO and i have to remove battery.
I JUST got this phone and really want to atleast get it back to Windows Mobile so i can restart my flash.
read the link in my signature...i was there and few of the folks succeeded after completing the process
Hoping it wouldnt come to this but looks like i dont have a choice, hopefully I get a try your method out tomorrow since the success rate looks promising, Ill get back with the results!
Try to reset your phone. Push the red little button on the back near the SD card
I have the HD2 open and have removed the flex cable at the bottom of the phone yet when i connect USB it auto boots so i have to power it down and to do that i have to connect flex cable. once i have the cable connected i power down then i hold the volume button and before i can restart the phoen autoboots from the USB being plugged in so im in a loop.
But i cant boot without the USB being in so Im in a pickle. Again
hunterthehuman said:
I have the HD2 open and have removed the flex cable at the bottom of the phone yet when i connect USB it auto boots so i have to power it down and to do that i have to connect flex cable. once i have the cable connected i power down then i hold the volume button and before i can restart the phoen autoboots from the USB being plugged in so im in a loop.
But i cant boot without the USB being in so Im in a pickle. Again
Click to expand...
Click to collapse
Try this:
- Hold down the vol_down button and don't let go.
- connect the usb, don't let go of the vol_down button
- should go into bootloader
- now let go of the button.
Nope that didnt work either, any OTHER reason my phone wouldnt acces the Tricolor screen? Ive tried everything 100 times.