Hello guys,
I got a HTC HD2 today from ebay, the seller has 100% feedback.
I have done a search about my problem but I dont wanna do anything wrong on the phone if the phone is faulty and send it back.
My situation was, I got the phone, inserted my SIMcard and set all the first settings. after 2min someone called me, when I answered the call couldnt hear anything and the phone was frozen :\ after few seconds the phone reboot itself and I waited 5min to see if turned back on, but didnt :\
I've tried pressing the yellow reset botton near the battery, I've tried hard reset.
And if I press VOL down and turn the handset on thats the info I get :
PB81120 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
and on the bottom of the screen says SERIAL, nothing else
I've got the phone from America (T-mobile) I'm in australia, melbourne
I've worked hard to get this phone and now when I got, could only use it for couple minutes
Please help me asap.
Thank you and sorry open other topic about it
Guessing its TMoUS HD2 Leo1024. BTW what rom is installed on it did you get to notice while you had it? Something is odd here you are not sharing with us how does it go and get stuck in that screen.
Well to be safe if you don't know flash it. So don't matter remove the battery and restart it and go to bootloader mode by pressing power button while holding down the bottom volume button. Then connect the device to your PC via USB mount and download and run HSPL or you can do it via stock rom go download 2.10 from WM dev archive thread.
I just got the phone today :\ the seller said to me the phone is the tmobile version 512mb. I'm a bit noob with HTC, Ive been with iphone until today. well, Im not sure which rom I had, but I think its LEO.
Ive tried all afternoon, I removed the battery out of the phone for 2 hrs, then tried again(without SIMcard) and the phone started up again as new settings and asked me to put my simcard in, so I removed the battery and put the simcard in, turned the phone on, it got stuck again in STICK TOGETHER screen
I dont wanna be inconvenient about all my questions, I just want my phone fixed :\
I couldnt do anything with the phone cos I set up the settings, after couple min got a call and the phone froze and it reboot it self stucking in STICKY TOGETHER screen. I was trying to flash it, but how can I sync my phone with windows 7? cos if I put in bootloader screen, it says USB at the bottom but WMDC says device not conected.
Do you have any solution for my problem?
thank you for your reply
Ahhh as you said TMobile I naturally thought it would be Leo1024(HD2-US) but now that you say its 512mb thats not TMobile you are using Leo512(HD2-EU). I had a feeling you flashed your rom as you flashed wrong one then.
So to verify post the HSPL and ROM data from where you got it from so we know. Also visually verify your actual device does it say TMobile on the top? does the button have colors? If both = yes its TMobile.
My phone has T-Moline on the top and has colors on the buttons. its definately t-mobile. I asked the seller and he said was 512, maybe he is wrong.
I havent done anything to the phone I cant flash cos I cant even conect with my computer the phone came from USA. I'm in australia
thank you
If it's a USA TMobile, then it's not the 512 version, and you need to flash only US TMO compatible ROMs or you could brick it.
When you say you tried a hard reset, how did you do that?
It should be when the phone is off you hold down both volume up and down, and keep them held down, then briefly press the power button but keep holding the volume buttons.
What happens when you do that?
Try to flash it through the sd card.
- Download the rom you want, uncompress the files, rename the nbh file to LEOIMG.nbh
(The original HTC rom files can be uncompressed too, even if they are .exe files - you will find a .nbh file inside)
- Copy this file to the root of the sd card.
- Reboot while pressing volume down.
It should start to flash the new rom.
That's what I called Hard reset
I'm doing it again and comes up a grey screen saying
This operation will delete all ur personal data, blah blah blah..
Press VolUp to restore manufacturer default, or press other keys to cancel
I pressed VolUp
..restore..completed
Press VolUp to bootup
Jeckas said:
That's what I called Hard reset
I'm doing it again and comes up a grey screen saying
This operation will delete all ur personal data, blah blah blah..
Press VolUp to restore manufacturer default, or press other keys to cancel
I pressed VolUp
..restore..completed
Press VolUp to bootup
Click to expand...
Click to collapse
Well if that appears to work, but doesn't, you could have a real problem there. Do what joooe suggested above - that's the only option you've got left, without sending it away for repair.
joooe said:
Try to flash it through the sd card.
- Download the rom you want, uncompress the files, rename the nbh file to LEOIMG.nbh
(The original HTC rom files can be uncompressed too, even if they are .exe files - you will find a .nbh file inside)
- Copy this file to the root of the sd card.
- Reboot while pressing volume down.
It should start to flash the new rom.
Click to expand...
Click to collapse
how can I know the right ROM for my phone, cos the seller is saying its t-mobile 512mb and @johncmolyneux says that t-mobile is 1024mb
I dont wanna brick my phone at all.
I'm from portugal but I'm in australia, let me know if you can help me flashing my phone detailed. regarding I'm noob about it :\
thank you
or what ROM do you recomend for me?
can I provide you more info about my phone? to get the right ROM for me.
thank you
AFAIK, if it says T-Mobile on it and it has coloured call buttons then it's a US TMobile. Only the US ones have coloured buttons, and they're all 1024MB ROM.
May be wise though to wait for someone else to confirm this, as you've got me doubting myself now!
what would happen if I install AFAIK rom and then my phone is 512mb? would brick my phone? I would be unable to use my phone anymore? thank you so much for all ur help guys
Jeckas said:
what would happen if I install AFAIK rom and then my phone is 512mb? would brick my phone? I would be unable to use my phone anymore? thank you so much for all ur help guys
Click to expand...
Click to collapse
I don't know if it's 100% bricked afterwards, but you do need to install a compatible ROM, made for your device, so you need to be sure which one it is. It's really not worth rushing this and trying to just install a ROM as you may irreparably damage your phone.
ok, I will follow ur advice
should I follow this thread?
http://forum.xda-developers.com/showthread.php?p=6894936#post6894936
how can I make sure is 512mb or 1024mb?
but it says :
1024LEOs (from T-Mobile with 1024ROM) ARE NOT SUPPORTED
but then if my phone is T-mobile with 1024ROM
I can follow this one yeh?
http://forum.xda-developers.com/showpost.php?p=6891358&postcount=1893
thank you very much
Like I said earlier, wait for a while and let someone confirm that it is indeed a 1024MB ROM, or you will probably brick it and not be able to fix it.
HSPL3 works on all types of HD2 though, so you can flash that. Those links are both actually the same thing.
Just don't flash a ROM until you know 100% that you have the right type.
It is the TMOUS 1024 LEO.
Go to the HTC website and download a T-Mobile USA ROM, you are required to enter the phone's serial number. This will guarantee that you only download a ROM that is suitable for your phone.
Since you really just want to test the phone then go for the 2.10 ROM.
Firstly press and hold the Volume Down button, then tap the power button. This will bring you into Bootloader Mode (as you previously have done). When you plug in the USB cable to the computer the 'Serial' on the phone's screen will change to 'USB'.
As an administrator run the ROM and just tick the box about activesync.
thank you.
can I provide more info about my phone? to make sure for everyone?
thanks
Jeckas said:
thank you.
can I provide more info about my phone? to make sure for everyone?
thanks
Click to expand...
Click to collapse
I was 99.9% sure and just wanted someone else to agree really.
Basically, US T-Mobile HD2 are the only ones in the world with green and red call/end-call buttons, and every US T-Mobile HD2 has 1024MB ROM. If the guy you bought it off said it was 512MB then that would explain why it's in its current condition. It sounds like he believed it to be a 512MB version, and flashed a bad ROM. It also sounds like he's palmed it off on you, believing it to be knackered.
As fred_up said, go the the HTC site and download an official ROM for that device. You should be able to install that with no issues and see if the phone definitely works or not.
Good luck mate
@fred_up
do I have to flash first with this HSPL3?
I have downloaded and the phone was detected I went just to the step to select HSPL version to install
the choices are :
2.08.HSPL
2.08.0000
what should I do first?
I will try to find the rom on HTC website.
thank you very much
Related
Hey all,
Just a little background information:
- Hard SPL'd my phone to flash Dutty's cooked ROM.
- All of a sudden one day, the phone switched off. I tried to boot it up but it will freeze on the HTC loading screen where it displays the radio version, ROM version in red down the bottom - the phone would not go any further.
- My computer won't even recognise it when I plug in my USB.
Anyway, I figured I'd try to uninstall HSPL and start over again. I downloaded an official HTC ROM, tried to load into the bootloader and now I'm stuck.
The screen reads:
Upgrade ROM code error
Please try again
If I pull out the battery/SD card, it will load into this screen again.
What *I THINK* may be the issue is that I didn't use the original ROM SPECIFIC to my phone, i.e. WWE Asian ROM.
I've updated the ROM image on my SD card but I can't get into the original bootloader to start the uninstallation process again.
Help!
Ok, nice and calm, are you sure you can't get into bootloader mode?
Power off, sim and sd card out (just to be sure)
hold volume down, tap power, continue to hold volume down.
samsamuel said:
Ok, nice and calm, are you sure you can't get into bootloader mode?
Power off, sim and sd card out (just to be sure)
hold volume down, tap power, continue to hold volume down.
Click to expand...
Click to collapse
I can get into the bootloader just fine.
It will display the error message and I can't do anything.
OK, so if you can get to the 3 coloured screen, you can just flash HSPL (if it isn't still installed) and flash a new rom.
Boot to bootloader(3 coloured screen), connect to computer, run HSPL.exe
samsamuel said:
OK, so if you can get to the 3 coloured screen, you can just flash HSPL (if it isn't still installed) and flash a new rom.
Boot to bootloader(3 coloured screen), connect to computer, run HSPL.exe
Click to expand...
Click to collapse
My computer refuses to connect to the phone.
I'll plug in my USB cable, windows will make the connection sound but the phone won't load into Windows Explorer.
What does it say by the spl? 1.42.0000? or 1.42.HSPL?
Actually it doesnt matter, when you hear the connection sound, thats enough, Run HSPL.exe, and if its not already installed, it should install, if it is already installed it will say 'hspl requires 1.42.000' or something.
Either way, you can then go ahead and flash a new rom.
samsamuel said:
Actually it doesnt matter, when you hear the connection sound, thats enough, Run HSPL.exe, and if its not already installed, it should install, if it is already installed it will say 'hspl requires 1.42.000' or something.
Either way, you can then go ahead and flash a new rom.
Click to expand...
Click to collapse
No, it doesn't work.
When I run HSPL.exe, it says it can't find my phone.
I already have HSPL installed with a custom ROM.
The phone is stuffed whereby I couldn't get past the HTC logo screen - it just freezes there.
I tried uninstalling HSPL thinking this would solve my problem with no luck.
The phone boots into the bootloader with an error message that I can't seem to get around.
Ah ok, so you get the error message on the 3 coloured screen? If that is the case, then spl itself is corrupt.
I thought you got the error message when the phone tried to boot, my mistake.
Next to try then is to find the original rom that came on your phone, and flash it from sd card, and hopefully it will overwrite the spl. It must be the correct rom for your provider and region, though.
If that doesn't work, then i'm afraid all I can do is wish you best of luck.
samsamuel said:
It must be the correct rom for your provider and region, though.
Click to expand...
Click to collapse
I think this is where I went wrong.
I tried uninstalling HSPL with a ROM that wasn't from my region which is why I'm getting these errors.
Surely there's a way around this?
If you can find your original rom, there is a good chance you will be fine, OR you can probably try the goldcard route, however i'm not 100% so i wouldnt go handing over cash (goldcard isn't free) until you are sure.
Do you know what rom you are looking for?
samsamuel said:
If you can find your original rom, there is a good chance you will be fine, OR you can probably try the goldcard route, however i'm not 100% so i wouldnt go handing over cash (goldcard isn't free) until you are sure.
Do you know what rom you are looking for?
Click to expand...
Click to collapse
I'm sure my phone's original rom was the WWE Asian version from Hong Kong.
I've uploaded the ROM onto my SD card but I can't get the bootloader to load it.
As stated before, I used another ROM at first and then it crashed on me.
Everytime I start the bootloader, it won't let me load the Asian ROM from scratch.
It just displays the error with no way around it.
Hmm, ok, just a couple of last thoughts then i gotta go to bed.
1 - sd card formatted fat32
2 - some people have better luck with 2gb cards than with bigger ones.
3 - Was the phone bought direct unlocked from HTC or is there a chance its provider locked? (i.e are you REALLY SURE you have the right rom)
4 - RUU_Signed.nbh coppied to sd card and renamed leoimg.nbh
Gotta go, best of luck.
ok. u are getting error in bootloader? what exacly is the error message you are getting..
Hard Reset
I had a similar problem to this and a hard reset solved the problem. Did you try a hard reset? I think its press volume up and volume down and power simultaneously.
DownloadMaster said:
I had a similar problem to this and a hard reset solved the problem. Did you try a hard reset? I think its press volume up and volume down and power simultaneously.
Click to expand...
Click to collapse
Even that won't work!
Confirmed hard reset but pressing "Volume Up", then the screen blacks out immediately and nothing happens.
When I press the "power on" button, all I see is an exclamation mark for a second then a black screen.
I think the solution is for you to try flashing to HSPL again.
1. Boot to bootloader mode by pressing Vol down key and click the Power button. You should get the tri colour screen, and the word "Serial" on the bottom.
2. Plug in the USB cable to your PC. The word "Serial" should then change to "USB".
3. Run hspl.exe as administrator.
I did the same as you previously when I tried to load the SEA 1.66 ROM on my Hong Kong English phone, and recovered it by using the above steps. I had to run HSPL 3 times before it worked. The first 2 times, it would seem to work as I'd get the "We Hacked it!" message, but when I rebooted the phone to the bootloader, it still wasn't HSPL. Only on the 3rd try, did it successfully load HSPL to the bootloader.
-edit-
You can download the original Hong Kong CSL ROM from a link in this thread.
got to say, if in doubt - goldcard it!!!
what is your spl version now? 1.42.0000 or 1.42.hspl '?
only bootloader is never a problem with hspl installed.
only bootloader is no problem with original spl version as long as you have a compatible stock rom.
\I wonder whether the phone would connect to computer properly.
After plenty of reading around, I've finally fixed the issue!
It was the easiest of all fixes - all I had to do was to download the original factory ROM the phone came with (.exe file) and run the executable with the phone plugged in via USB.
Thanks to all those who have tried to help.
I just bought it from eBay and it came in today. It had Laurentus26 on it, which was really buggy. So I reset it, but then it wouldn't go past HTC screen, then I flashed Stock ROM(T-mo) on it, and now its stuck at Stick Together screen. What is wrong with my phone please help I'm so sad
i think i had the same prob...
turn your phone off....press the down volume and the power at the same time and flash a new compatible rom, be careful with the radio......
crokdy said:
turn your phone off....press the down volume and the power at the same time and flash a new compatible rom, be careful with the radio......
Click to expand...
Click to collapse
Yes I tried MANY MANY times using the PC. But it still gets stuck. And now its stuck at "SOFTWARE UPDATE FAILED"
How do I force install from MicroSD?
1. go here to get the latest official ROM:
http://dl.htc.com/ruudownload/t-mobileUS/DeviceDownloads.aspx?pid=leo
2. Unzip the download and find the .nbh file. Rename it LEOIMG.nbh.
Put this file on the root of the storage card (the stock 16gb that came with the phone won't work). I recommend buying a 10 dollar sandisk 2gb for flashing.
3. Put the phone into bootloader mode. Easiest way to get into bootloader: press the reset button under the back cover followed by immediately holding the vol down rocker. Bootloader is the funny looking tricolored screen. It should stop on the screen for a couple of seconds, then jump to a grey screen that asks if you want to perform the update. Press the red end call button (power) to start or vol down to cancel.
That should do it. It should start installing. If not, I'm not sure what else can be done. This method will also "relock" the phone so you can't install any custom ROMs unless you hspl unlock again.
Good Luck
nrfitchett4 said:
1. go here to get the latest official ROM:
http://dl.htc.com/ruudownload/t-mobileUS/DeviceDownloads.aspx?pid=leo
2. Unzip the download and find the .nbh file. Rename it LEOIMG.nbh.
Put this file on the root of the storage card (the stock 16gb that came with the phone won't work). I recommend buying a 10 dollar sandisk 2gb for flashing.
3. Put the phone into bootloader mode. Easiest way to get into bootloader: press the reset button under the back cover followed by immediately holding the vol down rocker. Bootloader is the funny looking tricolored screen. It should stop on the screen for a couple of seconds, then jump to a grey screen that asks if you want to perform the update. Press the red end call button (power) to start or vol down to cancel.
That should do it. It should start installing. If not, I'm not sure what else can be done. This method will also "relock" the phone so you can't install any custom ROMs unless you hspl unlock again.
Good Luck
Click to expand...
Click to collapse
I tried an old Nokia 2GB card, it just goes to the screen where it says Serial. It's not recognizing a rom on the card. It also says "Update ROM code error. Please try again" it happened after I installed the last ROM on this list: http://www.vbnfiles.com/xda/xmoo/Leo/TMOUS/ since it had the most downloads.
Ali_Shaikh said:
I tried an old Nokia 2GB card, it just goes to the screen where it says Serial. It's not recognizing a rom on the card. It also says "Update ROM code error. Please try again" it happened after I installed the last ROM on this list: http://www.vbnfiles.com/xda/xmoo/Leo/TMOUS/ since it had the most downloads.
Click to expand...
Click to collapse
Are you getting that error when trying to flash from the card or from a computer via usb?
IF you get a ROM code error that means it is trying to flash it. I would go to the website I listed. It has you enter the S/N for the phone so you know it is the right Stock ROM.
p.s. Is it a tmobile branded hd2?
nrfitchett4 said:
Are you getting that error when trying to flash from the card or from a computer via usb?
IF you get a ROM code error that means it is trying to flash it. I would go to the website I listed. It has you enter the S/N for the phone so you know it is the right Stock ROM.
p.s. Is it a tmobile branded hd2?
Click to expand...
Click to collapse
yeah its a T-Mo HD2, and yes that's where I got the ROM after entering my IMEI #, it gives some other error on PC, and gets stuck at 8%. Also, while flashing that ROM it wasn't connected to Device Center, since the PC wouldn't recognize it.
I called T-MO and they are sending me a brand new one, anything I can do in the meantime?
Ali_Shaikh said:
yeah its a T-Mo HD2, and yes that's where I got the ROM after entering my IMEI #, it gives some other error on PC, and gets stuck at 8%. Also, while flashing that ROM it wasn't connected to Device Center, since the PC wouldn't recognize it.
I called T-MO and they are sending me a brand new one, anything I can do in the meantime?
Click to expand...
Click to collapse
if you have to send this one back to them, it needs to be stock or bricked.
Once you get the new hd2, I would try to flash a .51 radio onto the one you need to send in. That will brick it so they can't see that is not stock.
nrfitchett4 said:
if you have to send this one back to them, it needs to be stock or bricked.
Once you get the new hd2, I would try to flash a .51 radio onto the one you need to send in. That will brick it so they can't see that is not stock.
Click to expand...
Click to collapse
How do I do that?
Ali_Shaikh said:
How do I do that?
Click to expand...
Click to collapse
same way you flash a ROM, either through usb or from SD card:
http://forum.xda-developers.com/showthread.php?t=611787
Download a .51 radio and extract the .nbh file, rename it LEOIMG.nbh and put it on the storage card, enter bootloader, if it will flash, voila; instant brick!
I would only do this if they want the old one sent in and you can't get a stock ROM on it.
HALLO ALL,
i install hspl2 on t mobile htc hd 2 then i try to flash my phone with 1.66.405 rom.after that my mobile is not booting did i brick my phone or it can be recoverd........sorry for my poor english..help me friends
Is it a t-mo USA device? If so.. yes it's bricked.
When you say it wont boot do you mean you can power it on but it wont get past the splash screen? Or it just streight up wont power on?
Same as he said.. Does it power on? Power = good. Somtimes units will only power on when plugged into usb / charger. If this is the case, when it boots up go into boot rom by pressing vol down and reset in the back. When the tri color screen loads and says USB. Flash to a official rom such as the tmobile one.
man if you instaled 1.66 he is bricked i did the same with mine a big f mistake , but i fix it with cost , but is very hard to find service that will fix it , it just need a resurection ... if you still have the phone contact me. maybe i can help
Hey, the same happened for me..
When I put in my battery, it turns on automatically, shows the HTC screen, but never boots. Anyways, before it turns on automatically, I managed to do a light and a hard reset too, non of them is working.
Please, if somebody knows the way to fix it, contact me here or on my mail, [email protected]
I'll be waiting for you messages!
rvida said:
Hey, the same happened for me..
When I put in my battery, it turns on automatically, shows the HTC screen, but never boots. Anyways, before it turns on automatically, I managed to do a light and a hard reset too, non of them is working.
Please, if somebody knows the way to fix it, contact me here or on my mail, [email protected]
I'll be waiting for you messages!
Click to expand...
Click to collapse
Yours is totally different problem, and you should try flashing stock rom from sd.
Could you help me with that?
'Cause I don't even know where to start basically...
rvida said:
Could you help me with that?
'Cause I don't even know where to start basically...
Click to expand...
Click to collapse
Take a image from the original ROM Say Vodafone, T-Mobile (your operator)
Extract the file, for me it is : "RUU_Leo_Vodafone_NL_1.72.172.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship"
Use Winrar to extract this file : RUU_signed.nbh maybe called different but look for the biggest file extracted.
I hope you have a MicroSD
Rename
RUU_signed.nbh to leoimg.nbh put it on the MicroSD card
Put the MicroSD in the Phone,
Press down the Volume (left side) like you want less sound out of your phone
Press same time the Power On button hold it down until you see a bootloader
Now your ready to reflash original rom from the MicroSD
use HSPL 2.08 to load the not branded roms to the divice
Hope it works,
When you have Power in the phone then it wil work for sure
Ariebombarie
I got this phone on Ebay because I am poor. It was a T Mobile unlocked that was changed to Android. I can't get rid of the old user name and don't have the password for the Android market account set up on this phone. I can't do a factory reset and I need help. I would prefer to put 7 on it but I would be happy putting 6.5 back. Android would do if I could reset the user account. I do hope someone can help me. I am not very technically gifted but I can follow easy instructions. Please help me.
Judy
Because you are new at this I suggest flashing the stock T Mobile from your SD card. It is the simplest and safest thing to do.
You may need the Serial and IMEI numbers located under the phones battery.
1. Make sure your microSD is Formatted to fat32
2. Go to T Mobile web site and download the rom. It will ask for you IMEI number this makes sure the rom is for your mobile.
3. Unzip/unrar the downloaded file into a folder on your PC
4. Rename the RUU_signed.nbh file to LEOIMG.nbh
5. Copy the LEOIMG.nbh file to the root of your MicroSD Card
6. Plug the MicroSD Card into the phone
7. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
8. Follow the On Screen instructions to start the update
9. After flash has completed, press the reset button with the stylus to reset the device.
What if you want to flash it without using the SD card? I flashed android using NAND but I want to put WM 6.5 back.
oscar0324 said:
What if you want to flash it without using the SD card? I flashed android using NAND but I want to put WM 6.5 back.
Click to expand...
Click to collapse
I think doing it with the SD card is only way to get back to 6.5.
You could always boot into the boot loader by holding the up volume and power key then flash a 6.5 Rom.
Sent from my HTC HD2 using XDA App
GaryOG said:
Because you are new at this I suggest flashing the stock T Mobile from your SD card. It is the simplest and safest thing to do.
You may need the Serial and IMEI numbers located under the phones battery.
1. Make sure your microSD is Formatted to fat32
2. Go to T Mobile web site and download the rom. It will ask for you IMEI number this makes sure the rom is for your mobile.
3. Unzip/unrar the downloaded file into a folder on your PC
4. Rename the RUU_signed.nbh file to LEOIMG.nbh
5. Copy the LEOIMG.nbh file to the root of your MicroSD Card
6. Plug the MicroSD Card into the phone
7. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
8. Follow the On Screen instructions to start the update
9. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
I have spent hours looking and I just can't find the old version of the software. I will continue to look but if anyone has a link please help the IMEI 357779035940129
If i do this will I have to unlock it again for AT&T?
Stormynights said:
I have spent hours looking and I just can't find the old version of the software. I will continue to look but if anyone has a link please help the IMEI 357779035940129
If i do this will I have to unlock it again for AT&T?
Click to expand...
Click to collapse
Try this
http://xdafil.es/HD2/TMOUS/RUU_Leo_...dio_Signed_15.39.50.07U_2.10.50.26_2_Ship.zip
I do not no If you have to unlock it again for AT&T.
Cheers
GaryOG said:
Try this
http://xdafil.es/HD2/TMOUS/RUU_Leo_...dio_Signed_15.39.50.07U_2.10.50.26_2_Ship.zip
I do not no If you have to unlock it again for AT&T.
Cheers
Click to expand...
Click to collapse
Thank you so much for the link.
stop!!!!!!!!
Everyone has forgotten to find out what device this is, t mobile are all over the place and some ship 1024MB versions, don't flash anything until you work what you need, flashing incorrect tmobile roms could give you a really bad day and an expensive paperweight
I tried the data cable first and it won't sync with active sync because it is at this time android. It just isn't recognized as anything but a usb storage device. Then I tried the card. I put all the files on the card according to the directions and hit the volume down button and the power button and nothing happens. I then have to remove the battery to turn it back on. The screen that comes up when I first start the phone is dark forces team. There has to be a way to do this.
You have to be holding vol down before u even press the power button, then press the power button simultaneously. U should see a tri-color screen then connect your usb to pc and flash the 6.5 ROM
Make sure u start with the phone off
Sent from my HTC Desire using XDA App
[email protected] said:
You have to be holding vol down before u even press the power button, then press the power button simultaneously. U should see a tri-color screen then connect your usb to pc and flash the 6.5 ROM
Make sure u start with the phone off
Sent from my HTC Desire using XDA App
Click to expand...
Click to collapse
When I take the battery out and then hold down the volume and press the power button I get that multi screen and I got to the USB then nothing else happens. What am I missing?
dazza9075 said:
stop!!!!!!!!
Everyone has forgotten to find out what device this is, t mobile are all over the place and some ship 1024MB versions, don't flash anything until you work what you need, flashing incorrect tmobile roms could give you a really bad day and an expensive paperweight
Click to expand...
Click to collapse
WHY?
OMG I did it. I can't wait till my grand kids find out how cool I am now. Thank you to everyone that helped me.
Stormynights said:
I tried the data cable first and it won't sync with active sync because it is at this time android. It just isn't recognized as anything but a usb storage device. Then I tried the card. I put all the files on the card according to the directions and hit the volume down button and the power button and nothing happens. I then have to remove the battery to turn it back on. The screen that comes up when I first start the phone is dark forces team. There has to be a way to do this.
Click to expand...
Click to collapse
I had a few attempts before I got it so try again.
It worked for me with a 16GB card.
Turn off your mobile.
Hold the Volume Down and End Call (power) buttons at the same time.
When "Searching" appears on the screen, release the Volume Down button.
This guide may help. But ignore the things about custom ROM’s and HSPL for now.
http://forum.xda-developers.com/showthread.php?t=681317
ok, there are two versions of the HD2, one with 512MB one with 1024MB, some t-mobile US phones (TMOUS) have 1024MB, if you ge the wrong ROM you could potentially bugger your device
for instance, flash a ROM with a unsupported radio on your device than game over....potentially
if you have a TMOUS 1024MB HD2
flash to .51 radio an its screwed
flash to .50 radio an its ok, except 2.05.50.x radio which will screw it
and stick to TMOUS ROMS as well
if you have the regular world wide version we can flash to what ever we like
its important to find out what someone is using before recomending them to flash any WM6.5 ROM because if by chance that ROM contains an incorrect radio version for that hardware then its game over.
Hello Everyone.
TBH im my opinion you guys are my last hope to fixing my hd2.
So here's the problem.
I have a HD2 that turns on but does not have a functioning touc screen.
ABOUT MY PHONE:
HTS HD2
Has old android in it ( I dont know which one it is, but i can describe it. It starts up with a BootLoader asking to boot android, so i have the option to press yes or no. It has old blue theme in the background.
Here's the problem. I've called HTC support and i learn my phone still has manufacturers warranty. So basically i can just send in the phone, and ill id have to pay is shipping. BUT! here's the problem. HTC does not approve of third party software installed in the phone, in my case it is the ANDROID. So now im trying to wipe android put, and install windows mobile again. I downloaded the t-mobile stock rom and when i plug in my phone, the windows mobile center automatically pops out but it shows an error symbol.
TL;DR
So my question to you guys is how do i remove Android and install Windows Mobile on an HTC HD2 with a non working screen
Thank you so much guys for even considering to help me
Mod if i posted on the wrong section could you please move it for me.
Thanks
hi,
try this:
http://forum.xda-developers.com/showthread.php?t=956715
Thanks so Much But here's an update
I went ahead and downoaded the HSPL3
I turned on my phone and also pressing the voulme down button which brought to me to a red green and white color. I had my phon conneceted to the computer VIA USB. I first double clicked the T-Mobile rom update thingy and went ahead accpeted the warning signs etc,so the first thing that came up was identifying phone, and after 5 seconds it disappears so nothing came fro that, then later i double clicked the HSPL3 which asked me to either pick the 2.8 or the the 2.8 spl i believe, i had the spl installed so i wen ahead clicked the 2.8. it installed and my phone rbooted and BAM my touch screen worked, and when it asked to boot android i pressed NO. my phone rebooted and iagain the boot loader came up and asked to bott android, so this time i pressed BUt it didnt work because the touch screen stopped working!
So i went ahead to try everything all over but this time i clicked the 2.8 spl and after a minute on my phone it displayed " we hacked it" etc etc etc, i robooted my phone, ad it worked, i turned it on and off twice and it worked i was using my phone after a month So after playing with it alittle bit i decided to put my sim card in it. I turned off the phone and put the Sim card and turned on the phone so i can use it but.....once again the touch screen stopped working... ****!!!!!!
yep, now the touchscreen is once again not working
bump bumpity bump
fusion1204 said:
bump bumpity bump
Click to expand...
Click to collapse
Download a stock WM ROM for your phone, extract and rename your .nbh to leoimg.nbh. Transfer leoimg.nbh. to your SDcard.....enter bootloader mode....there it will flash back to your WM ROM with all HSPL remove. Time to send back to Manufacturer for repair..
Okay hold on. So when you see stock WM ROM coud that be the "T-Mobile_HD2_MR_Software_311...." file? and where can i find my .nbh file?
fusion1204 said:
Okay hold on. So when you see stock WM ROM coud that be the "T-Mobile_HD2_MR_Software_311...." file? and where can i find my .nbh file?
Click to expand...
Click to collapse
extract that from your .exe file.
Stock ROM can be found here
http://forum.xda-developers.com/showthread.php?t=655653
Make sure you use the Stock ROM specific for your phone, else you will brick your phone.
I went ahead and did that, but nothing changed did i do something wrong?
fusion1204 said:
I went ahead and did that, but nothing changed did i do something wrong?
Click to expand...
Click to collapse
Try following this guide....
http://forum.xda-developers.com/showthread.php?t=681317
10507 Thank you for the links but it didn't wok for me.
UGh!
Am i doing something woring? i mean i can get to the screen where it shows the foru colors, i guess that would be flashing and once i get there i can't do anything else the only way for me to do anything while im on that screen is if i have it connected in with my computer, and also start runinng the HSPL program which switches from Hspl to a NON hspl vice versa.
I hope youre not tired of me lol!
please help me out with this stupid situation im in.
Thank you.
Bumpity bump please help me out