Guys I already made some research here in the foruns but found nothing that could help, soo here I am asking for some help.
When I go out of my region, I need to add the operator number 36 and the region I want to call in this case 11. This is really a mess since I have to look at the number in my contat list record it on my memory and then type in the phone software this number after the 03611 number that I already explained.
I would like to know if there is a way to make it easier or even automatic. I know there is some kind of codes explained in the manual, but I think that I may be doing something wrong because I never got this to work.
Can someone help me on this?
Thanks a lot.
Felipe
I always store my phone numbers in the international format like
+CCC (AAA) XXX XXXX
where
CCC = Country code
AAA = Area / Operator code
XXX = Local Number
In this way, wherever I dial from, the correct number is dialed.
Effan
HTC SPRINT 6900
after hardreset
what can be unlock code ?
before was 000000
Unlock code
for my phone the code is 195304
just go to the phone keypad type ##778# or ##3282#
select edit and when asked for the code type in 195304.
##778# and ##3282# will direct you to two different menus.
I have sprint. If this does not work for you just call your carrier and tell them that your internet is not working thats how I got mine.
sprint unlock
alphaxi3 said:
for my phone the code is 195304
just go to the phone keypad type ##778# or ##3282#
select edit and when asked for the code type in 195304.
##778# and ##3282# will direct you to two different menus.
I have sprint. If this does not work for you just call your carrier and tell them that your internet is not working thats how I got mine.
Click to expand...
Click to collapse
hye...do u have any idea how to unlock sprint sanyo vero?
i want use it by another telco..hope u can pm me
And how to make my white Vogue from inject to using RUIM card? Is that need unlock methods? But how? Can someone help me please? Hope you can PM me too, please?
alphaxi3 said:
for my phone the code is 195304
just go to the phone keypad type ##778# or ##3282#
select edit and when asked for the code type in 195304.
##778# and ##3282# will direct you to two different menus.
I have sprint. If this does not work for you just call your carrier and tell them that your internet is not working thats how I got mine.
Click to expand...
Click to collapse
On my phone Sprint Galaxy S 3 the ##3282# got me to the menu to select edit but the code "195304" doesn't work. After an "incorrect code" message the phone reboots.
This is the farthest I've gotten so far. I bought the phone off of eBay so I don't think I can call Sprint since I don't have an account with them.
How can I find out what the second number is for my phone??
found code for my s4 mini
jack.prieto said:
On my phone Sprint Galaxy S 3 the ##3282# got me to the menu to select edit but the code "195304" doesn't work. After an "incorrect code" message the phone reboots.
This is the farthest I've gotten so far. I bought the phone off of eBay so I don't think I can call Sprint since I don't have an account with them.
How can I find out what the second number is for my phone??
Click to expand...
Click to collapse
I have a sprint s4 mini and my code was 222222. You can Try that. If that don't work call sprint and ask for the six digit unlock code. I herd they don't like you asking for the MSL unlock code for some reason. If that don't work I've seen that you can down load (unlockmymsl) app from play store. Then try inputting 222222 once. And you will get incorrect code message. Hit your home key then go to the app and it should give you the code. Some Phone's need to be rooted but mine worked by just interning 222222 in the edit dialog.
The MSL/SPC code is not the same for every phone.
First I would try giving sprint a call and asking for It. Just be polite and clear about what you want. If it doesn't seem to be panning out, I wouldn't bother making too big a fuss and wasting time on it. I would just hang up and call right back to get another rep and try again.
Unfortunately my knowledge is based in Samsung devices, so I cannot say much for HTC. I do know that you could retrieve the MSL/SPC by using adb shell or similar to
Code:
su
getprop.RIL
after attempting to input an incorrect code (any 6 numbers will work). If you enter the wrong code twice, the phone will reboot (nothing more than an annoying security feature). On Samsung devices, recent firmware has broken this method, and flashing an older stock modem/rom was required to get it to work. Samsung Knox further complicated this by breaking compatibility with older modems, and causing a downgrade attempt to brick the device... At least you aren't in dealing with that mess. I have no idea about HTC phones, though.
unlock sprint phone
Hello, I have a Samsung Galaxy Mega I got with Sprint and I would like to use Straight Talk With It, All the unlocking company's are asking for a 15 digit IMEI #... Mine only has a 14 digit MEID #....How would i get the code for my phone? Thank you
Does anyone know the code to unlock an iPhone 5s
I have a lg stylo 5 with a sprint sim lock how can i unlock it for free
I installed the Sprint TV cab that comes with the new ROM but every time I start the application I get this message.
Unable to get billing system indicator for the MDN(12)
MDN : ##########
CID : AFB52 - 73E8C- 16332
I noticed that the value of MDN is supposed to be my phone number but it's wrong. One of the numbers does not match with my phone number and I'm pretty sure that's what the problem is but I don't know how to change my device's phone number
Does anyone know how to change the phone number on Windows Mobile???
I'm sure the information is on this forum somewhere, but I'd say just give sprint a call. I can't rem. the exact steps so I won't tell you them as I don't want you wrecking your phone due to my poor memory...
I do know when I ported my number after getting my Mogul on Tuesday I was walked through some steps punching in various codes and the like and I was able to edit the phone number and something else on my phone.
jrobertiko said:
I installed the Sprint TV cab that comes with the new ROM but every time I start the application I get this message.
Unable to get billing system indicator for the MDN(12)
MDN : ##########
CID : AFB52 - 73E8C- 16332
I noticed that the value of MDN is supposed to be my phone number but it's wrong. One of the numbers does not match with my phone number and I'm pretty sure that's what the problem is but I don't know how to change my device's phone number
Does anyone know how to change the phone number on Windows Mobile???
Click to expand...
Click to collapse
I have the same problem with my Touch Pro. How do we change the MDN without going through Sprint CS? I have had enough of their crappy CS so I would rather get the info through the helpful mates on this forum.
dial ##778# send
then enter your MSL code, select edit, then select VIEW softkey, select NAM settings, there you'll find MDN, tap and hold with stylus and edit.
Hope this helps.
Oops, I just realized how old this was. Sorry, as it's probably already been resolved for the OP long ago.
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
I have the same problem. Both calls and text messages.
I don't think it matters if the international code is there or not.
Really frustrating not knowing who calls.
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Hmm, I've changed the SIM, but I can't remember if it worked wih the first SIM card.
But a hard reset deletes everything, right?
There are a few things you have to be sure of:
Do not have double contacts, if you have a number (with and without operator/country prefix) twice in your list it will not show any name.
I don't know if this applies if you have a contact on your phone memory and on your sim card. I am sure it does have this problem if you have two contacts with the same number on the memory phone.
For some reason this is logic: On an incoming call, the phones checks it's phonebook and retrieves two numbers and then it does not know what to display, is it contact one, or two?
I hope this helps you out. I did not experience any problems (yet).
AndrewCZ said:
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Click to expand...
Click to collapse
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
samluke said:
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
Click to expand...
Click to collapse
Hi guys!! i had this problem too but i have fix the problem. what i do:
!) i store all my contacts in my sim card and delete the contacts in the phone.
2)do a hard reset
3)upon doing the hard reset, the phone will prompt you on importing sim contacts and finding your service provider. select both and and press ok
4)now try to call from your house to your phone to do a check.
5)my problem was solved after this
hope it helps!
KraFT_mk said:
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
Click to expand...
Click to collapse
What was happening to me before the reset was a bit different - the phone wasn't able to match anything at all - even a number called from the phonebook and stored in "recent calls" in EXACTLY the same way it's in contact, didn't match to the contact when redialed.
I think that something required for Caller ID to work gets done when the phone is first initialized, and that this step requires full access to the phone module (which the phone doesn't have without a SIM inserted and a proper PIN entered).
hi,
i encountered also that worry,
i set the HKCU\Control Panel\Phone\CalIidMatch value:9
my mobile phone number to test was stored as "06xxyyzzww"
and when i phone my diamond2 from that number
the caller id is recognized
(with showing as +336wwxxyyzz)
i tested from my home phone stored in contacts as 04wwxxyyzz
i rang my topaz its was identfied as my home,
(with showing as +334wwxxyyzz)
i am in france, + is for 00 ,our phone numbers are 10 digits long
(mobiles and "home") ,
to be joined from abroad, you have to dial +33+phone number WITHOUT the first digit "0")
so the "9" value i put in the registry
if it could help you
regards
Hi,
just stumbled over the same problem.
The old phone (HTC P330) resolved numbers from my used format 01234-56789.
Since my contacts are a mess, I have 01234-12345, +49-123456-456, +49 (0123)-456 and so on, it would be a great pain in my ass to switch every contact to +49123-456 (which the new phone resolved).
I compared the Registry-Entry from the P3300 with the TD2 and voila: TD2 was 12, P3300 had the value 8.
I changed the TD2 to value 8, reboot and now I'm happy again, the phone is getting used to my contact list
Regards
Heiko
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Caller ID problem, my solution
I had the same problem. But after a hard reset it seems to work just fine now. Remember to backup your downloaded programs etc before doing this.
Tyven said:
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Click to expand...
Click to collapse
Hi,
"8" should be the good figure for you, as in France
we have phone numbers +33987654321
and "9" is the good value for me, in:
HKCU\Control Panel\Phone\CalIidMatch value:
Edit: i remove previous "edit"
in fact all my contacts had been erased" so it was normal to have no caller ID?
ps: is your carrier sendind all the figures when you're receiving calls, i mean +4512345678
so perhaps you're encountering a bug .
you should try to backup your device, with a soft like spritebackup(special price for htc owners on their webpage) and experiment an hardreset
and restore
regards
Hi ,
did you ever try to change the following:
RegistryEdit and Decreasing the CallIDMatch from 12 to 7 solved my Issue
See below
HKEY_CURRENT_USER\ControlPanel\Phone" name="CallIDMatch"
Greetings from Slovenia
Hello,
that is my first post so please do not be very critical to my english level and PPC skills .
now this is an old thread but for BULGARIA the correct registry value is "9". Here the mobil numbers are as follows "08xx 123456" (9 digits without the ZERO at the very beginning). that is why the usefull number is that (default for my TD2 was 8). Now after this fix the phone can correctly identify which number i want to dial when i am inserting it by digits, instead of selecting the exact person. i do not know am i explaining correctly but i will try to put some more detail on that. When i want to dial some particular number (for example "08xx 123456") the phone select me the correct contact no matter how i put this contact in memory. with "+3598xx 123456" or only with "08xx 123456". before that intervention the phone identifies me the correct contact only if i type the digits, exactly the same way that i have added it to the memory. So i think that this registry key does not have a universal resolution. the resolution depends on how many digits is using tha particular mobile operator.
i hope that will be helpful for someone who is happy to own an HTC and is happy with it ... like Me