Ok so I have searched all over the forums and through google to find an answer to this and I can't any where so here goes. I am currently running the syndicate rom with the extreme kernal installed and when I go to use set cpu I have it set to conservative but any time I try to limit the cpu speed with the sliders it doesn't tae effect. The green numbers above the sliders will change stating my preferences but the white numbers that show the actual speed of the processor will continue to climb past my desired bottleneck. It looks like thecpu always stays between a range of 200 mhz and 1.2 ghz no matter what I set it at. If I change the style to something other than conservative it will change the behavior like performance will keep it at 1.2 or what I select and battery saver will keep it at the minimum. On demand and interactive seem to respond as well but are a little buggy and any little touch on the screen will make the processor jump straight to the maximum and stay there fr a bit which I would assume would kill my battery quite a bit faster. Does any one know if this is an issue with the phone, rom, kernal and if there is maybe a better settng than conservative or a different kernal I could use I was looking into the phoenix or fluff kernal. Any help or recomendations would begreatly appreciated. Thanks
Sent from my SPH-D700 using XDA App
Its been a long time since Ive used it (2.2.1 scales pretty good) if I remeber right,interactive is what you want to select,but on some kernels conservtive is what you want to select.I never used the profiles,I think they dont work all the time.
That's odd I never had that problem with syndicate. And I know for sure that almost every overclocking kernel recommends conservative, for some reason the other profiles can cause problems. There's a couple things that I've learned.
Conservative, for one thing, is never going to be an on demand setting. Typically it will just up the cpu to the max you set it at whenever there is some sort of activity on the phone. Which begs the question, what do you have the max set at? if its 1ghz, remember that the kernel is overclocked, so a setting of 1ghz will allow you to go to 1.2ghz. (I'm almost positive you don't want to set it at 1.2, because then it will peak higher than that) I think the max you set it to should be the listed physical limit of the processor (ours is 1ghz obviously), and the overclocking handles it from there (at least that's been my experience).
Also, remember that when there is no activity (your phones in your pocket), the cpu will be at your minimum. So you save battery in that regard, because with out setting cpu limits, like if you're running stock, I think it might run at the max all the time. (I don't that for a fact tho) again, we pretty much have to run conservative, (I've read its something to do with these hummingbirds and setcpu and overclock widget aren't built fot them) so its an all or nothing deal, you can't get "just enough" processor setting.
Try creating different conditions to help yourself out. When I had syndiccate I had a different setting for the screen being off, for being plugged in to a wall, for being plugged in to a computer, and for being below a certain battery %. Those are really cool features and help out a lot.
And as far as other roms...I use baked snack right now with his ultimate kernel. Its only sllliggghttly less stable than syndicate (but most most most defintly stable enough for a daily driver), and I get much better battery life and performance. He recommends using overclock widget, which isn't as flexible as setcpu, but defintly gets the job done. You'll have to google baked snack and find his website since they kicked him off of here.
Hope that helps, let me know if I didn't quite answer your question correctly.
Sent from my baked and emotionless SPH-D700
From my experience,you need to set it to 1.2 to activate OC...That being said,there are some kernels that need the interactive setting to work right...and 2.2.1 scales to the lowest setting when screen off even without setcpu,thats why I dont use it anymore.I will again once we have an official OC kernel for 2.2.1.
Sent from my SPH-D700 using XDA App
I actually used to have bakedsnacks rom and I liked it but it became a bit glitchy on me but I did think the battery life was a bit better. I only am using eclair as I want to wait for a final build of froyo to come out from sprint so the developers can utilize it better. I tried some of the leaked ones but I prefered the 2.1 better, all of the 2.2 ones were missing minor things that I used so I switched back. Also interactive setting just keeps the processor at max clock for a really long time before it scales back down and I didn't like that. Has anyone used the fluff ondemand kernal that is supposed to be for bettery battery life with syndicated 2.1? So I have deleted setcpu but it seemed to eat my battery faster so I put it back on. Maybe I will try some other kernal configurations since I was told that I can swap kernals without looseing data.
Sent from my SPH-D700 using XDA App
Fluff was glitchy for me,I liked Xtreme kernel the best.
Related
For those of you on CM7 (preferably RC2 or later nightlies), are you using SetCPU or the built in CMSettings CPU manager? Which is giving you better performance/battery life?
I can't help but think that the built in CM Settings CPU tuner is going to be conflicting with my SetCPU profiles.
Been using nightlies since #30 or so, and I currently run SetCPU with a normal profile, a screen off profile, and a profile for <10% battery and haven't touched CMSettings' CPU manager.
I'm contemplating just uninstalling SetCPU for a day or two and seeing what a 1017max / 245min Ondemand or Powersave governor via CMSettings ends up doing to my battery life considering there will be no screen off profile.
Any thoughts?
I dumped setCPU after a lot of testing (and even bought it on market)
I'm finding I'm much happier using inbuilt CPU settings. I think battery life is the same but performance is better due to the fact that SetCPU would sometimes get stuck in my screen-off profile when turned on causing the phone to be really slow.
I recomend uninstalling setCPU, set your ONDEMAND governor with ~1Ghz and run it... You'll find your battery about the same but much less hassle.
I have yet to try that, I somewhat feel obligated to use SetCPU since I purchased it lol. But it probably won't be the last time I waste money at the market.
Neither. CPU tuner works best for me.
Sent from my HTC Vision using XDA Premium App
Utorrent76 said:
Neither. CPU tuner works best for me.
Sent from my HTC Vision using XDA Premium App
Click to expand...
Click to collapse
its the same thing :facepalm:
Try the inbuilt one... I think its way easier
I've been wondering about this too. I don't quite understand how it works. Can I just set the frequency higher till a certain point without changing the voltage and get the same battery life?
What's the best way of doing this? Just change the clock speed or do I need to change something else or update the kernel?
Whatever you tell SetCPU to do, you'll see the same settings mirrored in the CM settings.
I say setCPU cuz as battery gets lower... I have my CPU speed lower also. Basically, 15% battery lasts me forever :] lol
Sent from my T-Mobile G2
DJAeroX26 said:
I say setCPU cuz as battery gets lower... I have my CPU speed lower also. Basically, 15% battery lasts me forever :] lol
Sent from my T-Mobile G2
Click to expand...
Click to collapse
Definitely. This is the one thing I like about SetCPU is having the 10% and 5% profiles so that I can get the last few % to last forever if I need it. Although in normal day-to-day use I'm never pushing it below 20%.
ScooterG said:
Whatever you tell SetCPU to do, you'll see the same settings mirrored in the CM settings.
Click to expand...
Click to collapse
Yea I see this, as far as the governor changing etc.. This is why I'm wondering if it would be easier on my phone to just run only the CM Settings one.
I notice that every 5th or so time I unlock the phone, there is an obvious lag switching from the screen off profile, and my unlock sliders jitter around and it takes 4-5 tries to unlock the phone. I think this is probably partially due to both settings switching over trying to change.
I think I might try backing up and uninstalling SetCPU for tomorrow to see how it goes.
colonelcack said:
I've been wondering about this too. I don't quite understand how it works. Can I just set the frequency higher till a certain point without changing the voltage and get the same battery life?
What's the best way of doing this? Just change the clock speed or do I need to change something else or update the kernel?
Click to expand...
Click to collapse
I've read on here that overclocking the Vision's CPU up to 1 GHz requires no over-volting, and in theory should not affect battery life (but not sure exactly where that information originates from). But there has been lots of debate on these forums on whether the SetCPU app helps or hurts battery life depending on screen-off profiles (underclocking to save battery) or its constant polling of the CPU clock (possibly killing the battery faster).
A kernel that supports overclocking is already part of the CM ROM. If you are on CM, you can just adjust the clock speed under Settings>CM Settings>Performance>CPU settings. Or set the CPU clock using an app like SetCPU. Choosing one method over the other is what is being asked/debated here. If you are on the stock ROM, you need to be rooted, flash a custom kernel that supports overclocking, then install an app such as SetCPU or CPU Tuner to set the CPU clock to your liking.
redpoint73 said:
I've read on here that overclocking the Vision's CPU up to 1 GHz requires no over-volting, and in theory should not affect battery life (but not sure exactly where that information originates from). But there has been lots of debate on these forums on whether the SetCPU app helps or hurts battery life depending on screen-off profiles (underclocking to save battery) or its constant polling of the CPU clock (possibly killing the battery faster).
A kernel that supports overclocking is already part of the CM ROM. If you are on CM, you can just adjust the clock speed under Settings>CM Settings>Performance>CPU settings. Or set the CPU clock using an app like SetCPU. Choosing one method over the other is what is being asked/debated here. If you are on the stock ROM, you need to be rooted, flash a custom kernel that supports overclocking, then install an app such as SetCPU or CPU Tuner to set the CPU clock to your liking.
Click to expand...
Click to collapse
I'm not sure about CM's kernel with the over-volting but I do know that Pershoots kernel can be overclocked to 979mhz without over-volting (Pershoot told me himself).
At 1.8Ghz, I find the temp settings in SetCPU very useful.
Vision rooted, booted and scooted
Daughain said:
At 1.8Ghz, I find the temp settings in SetCPU very useful.
Vision rooted, booted and scooted
Click to expand...
Click to collapse
Well obviously.... But why the hell would you ever need to be running at 1.8ghz? The fact that you are always using a temp-specific profile method should show you that consistent 1.8ghz isn't good for the phone...
Okay so I uninstalled SetCPU last night and I'm going to run just the CM Settings CPU manager all day to see how it goes. Running like this:
ONDEMAND governor
Min CPU: 245 mhz
Max CPU: 1017 mhz
On nightly #19 also.
Okay so its midnight almost, and I'm at 13hrs unplugged and 52% battery still. Pretty general/light use, phone is just as snappy and the lack of a screen off profile doesn't seem to effect battery at all. Liking it so far! very interesting to see the screen off profile not mattering much.
SetCPU for me. I like to have a temperature and charging profile, to prevent the phone from overheating. Even at 1ghz the possibility exists, nice to have a backup incase.
I'm thinking set cpu conflicting with the cm built in caused my ****ty running problems. I have not used setcpu since and been good so far
Sent from prison
tackleberry said:
I'm thinking set cpu conflicting with the cm built in caused my ****ty running problems. I have not used setcpu since and been good so far
Sent from prison
Click to expand...
Click to collapse
With multiple tries... If you change the settings on one, it cancels the settings on the other... Maybe it's because you had set on boot enabled on both?
im going to run the CM tuner and uninstall Setcpu and see how it runs. i never thought about this but i do get that lag when i turn my screen on sometimes. im gonna miss having the profiles but ill see how it runs over the coarse of a couple days.
Hey there, I just a few days ago rooted and flashed the Syndicate Frozen rom and am not getting such good battery life...
I was wondering how big of a difference SetCpu makes on battery life/performance in general? With moderate/heavy use (internet browsing, facebook, email, txt messaging) how much should it improve battery life? am getting around 10hours at the moment with moderately light use... Is there any free alternative app that runs comparatively well?
I guess what I'm really asking is: is it worth it to buy setcpu, and will it make a dramatic difference on my battery life? This Rom is supposed to improve battery life, and I think I read is overclocked to 1.2... Will setcpu let me set this underclocked to 1,0 and then like 800 with screen off, 600 idle? Am new to the android thing [have had my EPIC only around 2 weeks today]
Thanks for any help!
Overclock widget does pretty much the same thing, and you're going to want to set something like
20mhz min 1 or 1.2ghz max
Then 100mhz min 400mhz max for screen off.
You can set the speed to.anything you want. If you want battery to be the best then.set it to 100/1000 on demand. If you emwant performance then 100/1200. Also I don't set profiles cause I was reading somewhere that they aren't good to use on any galaxy phone.
Sent From My Evo Killer!
http://www.setcpu.com/
Nice info read up on it and yes you can set it anyway you want like stated above. I bought mine from the market to support the dev for the hard work involved in making setcpu, dont know if you know but it is free for xda members just search for setcpu. It is only $2.00 well worth the price so please support the dev if you can.
063_XOBX said:
Overclock widget does pretty much the same thing, and you're going to want to set something like
20mhz min 1 or 1.2ghz max
Then 100mhz min 400mhz max for screen off.
Click to expand...
Click to collapse
20Mhz would freeze the phone. :O
I personally like running it @ 100 Mhz when screen is off and 1Ghz when screen is on.
Overstew said:
20Mhz would freeze the phone. :O.......
Click to expand...
Click to collapse
I am pretty sure XOBX meant 200, cause your right 20 is pretty much crawling...
Yep, I meant 200, the damn autocorrect kept changing mhz to Hz and I must've clicked backspace one too many times.
Thanks, so it would make a big difference in battery life?
Sent from my EPIC 4G FROZEN and Syndicated
androikid said:
Thanks, so it would make a big difference in battery life?
Sent from my EPIC 4G FROZEN and Syndicated
Click to expand...
Click to collapse
Don't expect it to magically give you another 4 hours up time. 1 extra hour would be high hopes.
I use SetCPU with the CPU set to 200/1000 and ondemand, and the battery life has improved GREATLY, well worth the $2 to support the Dev, IMO, even though XDA members get it free.
I've abandoned SetCPU and uninstalled it. Unnecessary consumption of system resources.
Same with any other user-space app/widget to control CPU speed scaling.
In the Bonsai ROM, the exact same capability, sans the profiles which I (and most people) don't use anyway, can be achieved by setting clock range and governor in /etc/init.d/24-cpufreq script. I expect that all the other OC kernels, if not every custom kernel, has a similar way to set CPU clock governor.
I have mine set to 100/1200 on demand, and it works well for the demands I put on it. Way low consumption at idle, but when I need something it instantly responds.
I routinely get 16-18 hours off the charger, and put it back on the charger with sometimes as much as 40% remaining, but as always YMMV. A lot of it has to do with the ROM, but I'd say that CPU scaling has realized a tangible gain for me.
dwallersv said:
I've abandoned SetCPU and uninstalled it. Unnecessary consumption of system resources.
Same with any other user-space app/widget to control CPU speed scaling.
In the Bonsai ROM, the exact same capability, sans the profiles which I (and most people) don't use anyway, can be achieved by setting clock range and governor in /etc/init.d/24-cpufreq script. I expect that all the other OC kernels, if not every custom kernel, has a similar way to set CPU clock governor.
Click to expand...
Click to collapse
Talking about Bonsai ROM tweaks on a Syndicate thread would be like me talking about BMW mods on a Honda forum. Either way, I looked around in the system folders and I can't find the 24-cpu file you're talking about. I upgraded yestereday from the 2.1 SyndicateROM to this, and for the first few hours, the ROM itself was definately quicker...I don't know if that's just because I came from 2.1 to 2.2, not to mention all the other 2.2 tweaks. After a few hours, I completely forgot that I could overclock this to 1.2Ghz. Installing SetCPU and bumping it to 1.2Ghz felt like just another jump. System resource consumption aside, it makes the phone all that much quicker while going between screen, apps list, closing apps, etc.
I could care less about battery life because I've learned to always have a charger around me since my days of the Moment, of hell, even my Treo's. I want fast, SetCPU is something I can see the difference in just from turning it on and off and seeing the differences.
After reading through the Thread for the Pre Release of FuguMod Ultra in the development section of this forum I thought I would post some info up for people who are wondering why it doesn't work with their phone, and just some general info on overclocking.
- First off, not all phones will be able to run at 1366MHz. Every CPU made has a range of freuqencies it will work at, and it is different for every single one. So some may be able to handle 1366MHz and above, others may max out at 900MHz. If you are getting black screens, freezes, or random behaviour, then your CPU doesn't like the frequency you have it at, try a lower frequency.
- Always keep an eye on the temp of the CPU when testing overclocking, if the CPU gets too hot, and fail safes don't work, there is a chance you could fry your CPU.
- With the FuguMod Ultra kernel, you must also be aware that gpu bus frequencies have been changed, so if your phone is not happy with that it will black screen. (as bus speeds are like cpu speeds, every different device can handle different clock speeds)
- plls values have been changed, and these may cause problems on your phone.
So if you want to have a go at overclocking your phone, back it up, and then give it a go. Select a frequency, and test with something pretty cpu intensive (3d game, multiple quadrant passes) and see if there are any bugs/overheating during a 15min time period. If you notice any problems/too much heat, try a lower frequency, and try again. And if for some reason your phone doesn't like the kernel, you can reflash with your previous kernel or a new ROM as you have already backed up your data.
If you have any other questions about overclocking, feel free to post here and I will try my best to answer them.
--- Samsung G3, InDroid 4.3, FuguMod 2.4 B3 800MHz ---
How can you check the CPU temperature? I thought it was only battery temperature.
Sent from my GT-I5800 using XDA App
dilzo said:
How can you check the CPU temperature? I thought it was only battery temperature.
Sent from my GT-I5800 using XDA App
Click to expand...
Click to collapse
The battery temp is a good representation of how hot the processor is getting as it is right next to the battery (only a thin sheet of metal seperating it) If the battery rises in temperature by a few degrees, then you can summize that the cpu is probably getting a few degrees hotter than that. I really wouldn't recommend letting the battery get above 55degrees (celcius) as this means the CPU may be getting up close to 65degrees (celcius) which is a very bad thing.
Good post.
Note that if you want to make some stress-tests, you have to put "PERFORMANCE" governor and set the max freq you want to test.
marcellusbe said:
Good post.
Note that if you want to make some stress-tests, you have to put "PERFORMANCE" governor and set the max freq you want to test.
Click to expand...
Click to collapse
Yes, Very true!!
Must also say, Your kernels are pretty legendary! Waiting patiently for the offical release of your FuguMod Ultra
m not able to see time in state with both setcpu and cpuspy and it seems deep sleep is also not working.
Piyush Rawal said:
m not able to see time in state with both setcpu and cpuspy and it seems deep sleep is also not working.
Click to expand...
Click to collapse
How have you got your phone set up? i.e. what ROM are you using etc.
I am using stock jpq with app2sd, swap, zipalign, ramhack and stuff. Setcpu is installed with default min/max freakquency, No profiles in use and undervolt a bit.
Ok,
This may be an issue caused by XXJPQ, as it is a new release there may be some sort of conflict. Have you tried asking if anyone else has this issue in this thread? http://forum.xda-developers.com/showthread.php?t=1132697
I haven't played around with JPQ yet so don't know what the bugs are yet.
Also, are you running a stock kernel? Have you confirmed that the phone has been rooted properly as well?
It's definitely a bug in Kernel. I tried three different roms and i wasn't able to check time in state in any of them (I am talking about fugumod ultra prerelease kernel here).
With previous versions of fugumad kernel everything is fine. So definatly a bug in kernel.
Piyush Rawal said:
It's definitely a bug in Kernel. I tried three different roms and i wasn't able to check time in state in any of them (I am talking about fugumod ultra prerelease kernel here).
With previous versions of fugumad kernel everything is fine. So definatly a bug in kernel.
Click to expand...
Click to collapse
Ok cool, I'll report the bug to the developer so that he can have a look into it. Thanks for testing and proving to the kernel.
Little bit of info some might find helpful. After some recent testing, I have found that some people might experience a black screen freeze when phone is in standby for a while with 83MHz min setting and on demand governor. I am not sure of the exact reason for this, whether it is a bug, or that the processor just doesn't like going that low for extended periods of time. If you experience this type of error, just hard reset the phone then open setcpu after phone has loaded and change the "standby" profile minimum to at least the next step up on the slider. Personally I use 223 setting as it provides a smoother lock screen animation, and no significant difference in battery drain.
Sent from my super smooth GT-I5800 using XDA App
I'm running Bionix V 1.3.2 with the Immortality 2.1 kernel.
What I'm curious about is everyone's preferred overclocking app?
From what it looks like, it comes down to SetCPU, No-frills, Tegrak, or CPU tuner.
No frills advertises doing the overclocking without running in the background- which is appealing.
What are your thoughts?
Im not familiar with anything other then set cpu. I like it because I set up profiles for charging, screen off and temp. Ive used it for a while even when not overclocking, just for the screen off profile.
go with set CPU that's great the profiles really help save battery
Sent from my SGH-T959 using XDA Premium App
You can use Voltage Control to OC too...
Sent from my XDA app cuz I'm stalking your mom....
So it looks like there are a couple of categories the overclocking apps can be divided in to- those with profile management and without, and those for the SGS only.
Profile Management: SetCPU ($1.95), Tegrak ($1.95), CPU Tuner (Free)
Without: No Frills (Free), Voltage Control (Free/$3.84)
Both Tegrak and Voltage Control are specific to the SGS family- why would I want to buy a program that only works with specific phones when I can get a solution that will work with all my future phones?
I know SetCPU is the most commonly used solution, but I keep reading so many complaints in the forums. Does anyone have any experience with CPU tuner in comparison to the others? I'll at least tinker with it when I have time since I'll have more than 15 minutes to see if I like it.
Set cpu is horrible, atleast from my experience.
Constant screen of death, meaning after I lock phone,it won't turn on until reboot.
Instability. Lagged my phone even with oc only up to 1.2
Voltage control is what I prefer.
xriderx66 said:
Set cpu is horrible, atleast from my experience.
Constant screen of death, meaning after I lock phone,it won't turn on until reboot.
Instability. Lagged my phone even with oc only up to 1.2
Voltage control is what I prefer.
Click to expand...
Click to collapse
Sounds like your kernel is not compatible with setcpu =]
Some are not and votage control is preferred.
I'm on MIUI revamped Xx-2 with glitch 11 anf haven't had a problem with setcpu.
Vibrant+MIUI
Setcpu because in the "About? " it has says "Its over 9000! " plus its simple to use.
Sent from my SGS-t959 using XDA App
Well I'm using voltage control right now because its tailored to the hummingbird and I like the undervolt settings. Once you find the right voltages, your battery will be (more) amazing.
However, I've used setcpu since I've had my htc hero and it works wonders...at first when the galaxy s came out, there were conflicts and setcpu couldn't tune the hummingbird(atleast for the Epic 4g, the Galaxy S for Sprint), but that's since been worked on.
Setcpu is very straightforward. When you start it up, just tap autodetect speeds and it'll have a slider for min/max and yyou just slide it to the appropriate speeds. Then you use "governors" that dictate how the processor clocks...for example, on "conservative" the cpu scales up to the speed it needs to process what you're doing and slows down really fast when not in use. "Ondemand" is basically the same thing, but it scales high up and then lowers itself to the needed speed. "Performance" keeps your cpu clocked at its highest speed and keeps it there. Its good to run performance when you need to run benchmarks or do a lot of stuff on your phone at once, because it kills the battery faster (obviously)
Just try em out...setcpu is free on xda, just look for it in the apps section on android general I think or the g1 boards
Voltage control, be wary about, because if you mess with the ettings and don't know what you're doing, it'll corrupt your phone.
Sent from my SPH-D700 using XDA Premium App
I like voltage control too and pimp my CPU mainly because SetCpu hardly ever supports the kernels I use and when it does it gives me reboots
Thank you, I'll give Voltage Control a try. Do you have any 'safe' recommended voltage settings when using smartass, and then I'll see the limits of my phone from there?
No sorry idk about the vibrant, but it sould be able to handle the uv since we're both hummingbird
When you use VC, do it one clock speed at a time. The voltage slider moves in -25mV increments. Each processor is different. For example, my phone can handle 1.4ghz unervolted by -50mV but if I put it down one more notch, my phone freezes and its FC galore. So its good to have a backup.
If you're not turned away by the amount of time it takes to tune VC, then it'll be worth it. You just have to thoroughly test the phone each time you undervolt to make sure its stable before you set it as Boot. To test just scroll around and run acouple of benchmarks.
For example, when I started my UV, I started with 1.4ghz and worked my way down to 1.3, 1.2, 1.1, 1.0, .8 and .6 ghz. Slide it to 1400MHz and then slide the voltage bar one notch to the left to uv it by 25mV. Hit apply and then run smartbench, quadrant, neocore, linpack, w/e just to make sure your phone can handle it. If it can, move it one more notch and test it out. Rinse repeat for the rest
Setcpu is way more user friendly and does what its supposed to, but vc is for power users I guess
Sent from my SPH-D700 using XDA Premium App
If I do recall you could also change the voltages in setcpu. Ya know if your kernel supports it.
Sent from my SGS-t959 using XDA App
hi
i have a htc evo 4g running android 2.3.5 and kernel 2.6.35.10-g4b48446 [email protected] #1 and i have a few questions on setcpu. its a stock rom and it is rooted.
I shut off my profiles and disabled the perflock - it said success. So i ran the long bench test and only got 2078 ms, not 5000. so i dont know if its really working. I reengaged the profiles and i think it works with the screen off. the rest of the time i am not so sure. in fact it seems to still drain fairly rapidly unless i turn on some battery saver or something. I have the following settings on my profile all are set to ondemand except charging which is set to performance. the only other setting i can choose is user
in call 998 max and 245 min priority 91
screen off 384 max and 245 min priority 88
charging any 998 max and 245 min priority 85
battery <25% 460 max 245 min priority 81
bbattery <50% 883 max 245 min priority 65
Temp> 42 C 614 max 245 min priority 50
what am i doing wrong? I have it enabled and i have notifications off
i have system panel to try and monitor but its not recording and it also drains the battery like crazy so i think thats set wrong as well but i dont know why.
i also tried juice defender but it doesnt work right because it says the AOSP file isnt found in the system/app folder. I looked there and also in teh data/app folder and its not there. So i dont know what to do about that.
thanks
stock sense is just not all that efficient really. (well thats my opinion) profiles seem to look ok but also finding a different kernel with different governors (smartass v2 is rather efficient and changing around the frequencies as needed)
auto sync settings as well? turning some stuff of that you dont use or look at and so on can help too
and calibrating battery a bit can help aka a full discharge a full charge and full discharge will sure help (also what i have found personally)
kernels
thanks for the reply. You mentioned different kernels. I understand about rooting my phone but not so much about how to load a different kernel or different rom. Where do i go to learn about that?
jjdonohue said:
thanks for the reply. You mentioned different kernels. I understand about rooting my phone but not so much about how to load a different kernel or different rom. Where do i go to learn about that?
Click to expand...
Click to collapse
look around in the development section as there are some great kernels available right now...Ca1ne just released a new version of the underworld SBC v6 that i personally like with great battery life ...Mason kernels are also great with great battery...just make sure u read the threads completely to make sure u are using the right kernel for the rom u are using...ie there are kernels for ics...sense....and so on......also the kernels load through recovery...just load kernel to sd and wipe cashe and dalvik and flash zip...hope this helps...Carp
Hi another question about kernels. I am a bit of a newbie other than rooting my phone so i want to understand what advantages/disadvantages different kernels have. You mentioned smartassv2. i have seen others like
chopsuey kernal
freedom kernel
golden monkey kernel
savaged-zen kernel
tiamat kernel
all of these i think support sense roms.
as i understand it , you have to go into the recovery screen and load hte zip file off the sd card and reboot with the new kernel. What are the risks/rewards of doing so? I guess i am trying to understand which one would suit me best.
i have the current sprint lovers rom i guess since it is factory stock so should i also be considering changing the rom? Maybe i am getting ahead of myself here.
thank you again.
which rom are u wanting to run....this will help us steer u in the right direction
im sorry your entire post didnt load on my end i see ur running sprint stock....that is a fine rom but i have not ran it myself....
---------- Post added at 01:53 AM ---------- Previous post was at 01:36 AM ----------
i personally have switched to sbc kernels when they came out with a sense version...i am addicted to sense 3.5...just my personal likings...sbc is superior battery charging whichcarp will give u better full charge on your battery so when the light turns green and u unplug it it wont drop down to like 90% battery in just a few mins....i can squeeze another couple hours out of my battery with sbc and even more depending on light usage....but u will stil need to play around with different cpu speeds like 786..921 and so on to see what your individual evo can stand....what works for 1 may or will not work for another....lags and bootloops etc...
You don't need to change Roms, you can if you want, but changing kernels will unleash new features. Some features are:
Full hdmi mirroring
The ability to over/under clock CPU
2 way call recording
Improve battery charging
Enable swap space
Improved performance of phone
Some kernels allow under volting CPU to further save battery (this can cause some stability issues so start slow with undervolting)
You may want to take a look at Lionfish kernel also, just note first boot may take a while.
Also ditch the profiles in set CPU, I tried profiles and it never seemed to work right. A good governor will handle all your profile settings.
I like smartass, and intellidemand the most on my set up.
As an idea ok the battery life I am getting, I streamed Pandora over 3g for about 8 hours not much other phone use, screen off most of the time, and my phone was at like 20 %. I thought that was pretty good.
Sent from my Synergized Aggressive Lionfish Evo using the XDA app
thanks detcup4evr for helping out explaining that better...i blew out my back and between no sleep and pain meds the brain just dont want to fire...thanks for stepping in bro....carp
smartassV2 vs InteractiveX ... which one giver better performance AND battery life??? currently I am running LIONFISH 1.8 with interactive X
Using profiles in setcpu actually uses more battery life. Because it has to be running all the time and monitoring phone state to know when to change to a different profile.
interactiveX vs smartassv2 all depends on how you use the phone and really which kernel it is. I've noticed little things like on mason's I got better battery with smartassv2 but on other kernels I get better battery with interactiveX. As far as performance, you won't realize a difference.
ok so it sounds like i should try the sbc sense 3.5 kernel with the smartassv2 governor. Did i get that right? i will look around to see where i can download that.
Were you refering to this kernel?
Underworld Sense Kernel v0.6
yes this is the kernel i run with ODJDub HD Bliss!! Sense 3.5...if u choose to run this rom it will give u alot of different options of kernels and apps and other things from the installer....if i can help u more just feel glad to hit me up....carp
Ok so with lionfish 1.8 kernel and interactivex, I should not use a profile? What does CPU go to on screen off? also where does it mention profiles use battery? I'd like to read more into this..
Thanks
Sent from my PC36100 using Tapatalk 2
Sense rom with Underworld v 0.6
At Carp -
thank you for the advice. I was thinking maybe i would use my ROM still (its a sense i believe) and load the underworld v0.6 kernel with sbc and see how that goes. I havent done very much research on ROMs so i dont know that i want to get that deep into this just yet. It seems like underworld has alot of nice features. One thing that i am wonderig though is with the new kernel would have any further ability to unload some of the sprint bloatware or do i need a new rom to do that or is there another way to do it? Things like qik video , gmail, accuweather blockbuster etc all load themselves periodically. I kill them but then they come back like weeds. Even programs i do like , like pandora, wheres my droid etc come back also. But i dont want them to.
no u will be fine getting rid of apps and bloatware u dont wont...u wont need a special rom....i use a free app in the market called root uninstaller to get rid of useless bloatware,apps etc...then u can go in and manually uninstall what u don't want...be careful not to uninstall anything which the phone needs to boot and operate such as android system...you will see the things u are looking for when u load the app...hope this helps...carp
I actually did something unusual.
I have universal aggressive lionfish SBC 1.8, swagged out stock N, and smartassv2
I set the ideal, sleep, and wake freq for smartass v2 to 128, while setting the up rate to 245. I used set cpu to lower the min freq for my device to 128. I set max load to 100, and min load to 85, and down time to 0. I then set a profile for "ondemand" during screen off, of 128-384.
I actually have pretty awesome battery life (I'm an uber heavy user).
Sometimes it reads that I spend over 70% of my time at 128mhz.
I feel no lag. It clocks to 998mhz maybe 15% of the time, mainly when loading web pages.
flashed underworld v 0.6
Hi Carp,
well, i flashed the underworld v 0.6. So i see in set cpu that i can underclock to 128 and overclock to 1228. however, i slid the slider over to 1228 by accident and it froze the phone even though it says its still at 998 mhz. then it rebooted by itself. so i guess that wasnt a good idea. Anyway, theres a ton of governor choices now in the profiles section. i am not familiar with alot of them but i was wondering which of those would provide the most benefit. they are as follows -
ondemandx
interactive x
intellidemand
smartass
interactive
conservative
smartass 2v2
performance
along with ondemand and user space from before.
thanks
Good to hear....u will need to try different settings as each evo will be a little different...ie.. some can take alot of overclock and as u said when u went to high it locked up......my evo likes min 245 and i dont go very little over 998...mine does not like high overclock....i run between 768 and 998 or until i can see a lag or slow down in performance..depends on which rom i am running...i like ondemand x and smartass 2 on my evo but there is a good read in papa smurph's smurphed out v6.6 thread in development on governors and such...go to post #2....i wish there was a perfect setting i could give u but u will have to see what your evo can take...part of the fun of android.....carp
Governors
Thanks carp. I guess experimentation is the only way to know. i charged my phone last night ad i noticed that it does take alot longer to go from 100% charge to 90% but i also noticed that the phone temp was at like 110 deg F and a voltage around 4.263 or so. i have read some thread where they claim its bad for the Lithium ion batt to be over 4.2 V but as soon as i unplug it it drops to 4.1 something usually. I am using battery indicator app to measure it. i am using the underworld w/sbc kernal currently but the voltage being higher has me a bit concerned that i am damaging the battery kind of like pumping water into a jar with the the lid on tight til it bursts. Or in the batteries case - too hot i guess or until it plates.