I was trying to follow these instructions:
http://forum.xda-developers.com/showthread.php?t=893948
I got as far as installing MAGLDR. When the phone restarted itself, it will not go passed the O2 welcome screen.
A hard reset (VolUp + VolDown + power) doesn't work.
If I hold vol down while I power it up it goes to the Red,Green,Blue,White screen where it says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
Can someone please advise me what, if anything I can do to get my phone working again?
Thanks.
no u are not bricked just reflash magdlr when its in the tri color screen vol down + power next time post in questions forums
Turn off phone by taking out battery and put it in
Then hold down vol down and then press off/end call button
should take you to coloured screen then connect to computer and it should say usb at bottom
then download the htc hd2 software off the htc site then flash the original software and should be back to normal
every nand build i test i do the following...
1. task 29
1b. flash radio
2. magldr
3. nand build
Are you holding end button while booting? that'll take you to magldr menu.
if it doesn't, then don't fear yet, cuz it's not bricked. Bircked is when you can't even turn it on, or it doesn't boot, or something like that. You can't even enter the rainbow screen when it's bricked.
sj1992 said:
Turn off phone by taking out battery and put it in
Then hold down vol down and then press off/end call button
should take you to coloured screen then connect to computer and it should say usb at bottom
then download the htc hd2 software off the htc site then flash the original software and should be back to normal
Click to expand...
Click to collapse
It's cool that you're trying to help but this is how people brick their phones. It's obvious, from him posting on here, that he's panicking. He'll go to htc site and just download any official rom and if he has a tmousa hd2 he's bricked it now. Not saying he does but you have to be specific with people around here. You'd be surprise how many complete newbs are on here who Just refuse to bother searching and reading
Yellowbrother said:
every nand build i test i do the following...
1. task 29
1b. flash radio
2. magldr
3. nand build
Click to expand...
Click to collapse
I've sucessfully put a few different NAND flavors on my phone but I have one quick question. What is "task 29"
help
teedor said:
I was trying to follow these instructions:
http://forum.xda-developers.com/showthread.php?t=893948
I got as far as installing MAGLDR. When the phone restarted itself, it will not go passed the O2 welcome screen.
A hard reset (VolUp + VolDown + power) doesn't work.
If I hold vol down while I power it up it goes to the Red,Green,Blue,White screen where it says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
Can someone please advise me what, if anything I can do to get my phone working again?
Thanks.
Click to expand...
Click to collapse
listen just download a official rom from hd rom development
and then extract the file with 7z or winrar
you will see a nbh file
change it to as follows leoimg.nbh
place it on any empty micro sd card and insert it into the phone
and then restart with holding vol down
after the tricolor screen you will see a grey screen with options for updating your rom
just follow the instructions and you will install a new wm6 rom
after that follow the video and the instructions for the noobs on the hd2 nand rom development section ,download the video and follow it as it says you will be fine.
i have been through this and this is what i did and i am with gauners hd nand version on my hd2 running perfectly
broknindarkagain said:
I've sucessfully put a few different NAND flavors on my phone but I have one quick question. What is "task 29"
Click to expand...
Click to collapse
It's used to clean NAND of leftover from previous ROMs.
Sent from my HD2 Droid using XDA App
There are a few methods to fix your problem actually,
Restore back to Factory Default with Official HTC firmware
Download Official HTC HD2 O2 firmware
Extract RUU_signed.nbh from the EXE file using 7-zip
Rename RUU_signed.nbh to leoimg.nbh and copy to the root directory of SD Card that is formatted in FAT16 or FAT32 and insert it into device
Power off your device
Hold onto the Volume Down Button and Power up the device
The bootloader will auto detect the leoimg.nbh file, and will start restoring back to default. This will restore your SPL, RADIO and FIRMWARE.
RED/GREEN/BLUE method
Power down the device
Hold Volume Down button and Power up the device
You will then see the RED/GREEN/BLUE screen
Connect the device via USB to your Computer
Wait for RED/GREEN/BLUE screen to show USB on the bottom instead of SERIAL
Run RADIO Upgrade (MAKE SURE YOU HAVE 2.10.50 and ABOVE)
I am GUESSING, your RADIO version is incorrect, causing it to loop.
You must use HSPL 2.08
You must use RADIO version that supports 576mb of RAM
Radio Thread
Incidentally, you can also reflash the firmware to any WINMO custom or official firmware while in RED/GREEN/BLUE screen as long as the bottom says USB and the device is really connected to the computer via USB. It might overwrite MAGLDR, and it might boot back into the official or custom firmware.
xcesivemastub8ah, both method works, again, help is "FREELY" provided to people who are willing to take the advise. People need to understand, if they tinker with something, they can and will tinker it to death. If you don't want to brick it, don't mess with it, use it as intended by the manufacturers, stock original.
No bootloader !!!!
LiFE1688 said:
There are a few methods to fix your problem actually,
Restore back to Factory Default with Official HTC firmware
Download Official HTC HD2 O2 firmware
Extract RUU_signed.nbh from the EXE file using 7-zip
Rename RUU_signed.nbh to leoimg.nbh and copy to the root directory of SD Card that is formatted in FAT16 or FAT32 and insert it into device
Power off your device
Hold onto the Volume Down Button and Power up the device
The bootloader will auto detect the leoimg.nbh file, and will start restoring back to default. This will restore your SPL, RADIO and FIRMWARE.
RED/GREEN/BLUE method
Power down the device
Hold Volume Down button and Power up the device
You will then see the RED/GREEN/BLUE screen
Connect the device via USB to your Computer
Wait for RED/GREEN/BLUE screen to show USB on the bottom instead of SERIAL
Run RADIO Upgrade (MAKE SURE YOU HAVE 2.10.50 and ABOVE)
I am GUESSING, your RADIO version is incorrect, causing it to loop.
You must use HSPL 2.08
You must use RADIO version that supports 576mb of RAM
Radio Thread
Incidentally, you can also reflash the firmware to any WINMO custom or official firmware while in RED/GREEN/BLUE screen as long as the bottom says USB and the device is really connected to the computer via USB. It might overwrite MAGLDR, and it might boot back into the official or custom firmware.
xcesivemastub8ah, both method works, again, help is "FREELY" provided to people who are willing to take the advise. People need to understand, if they tinker with something, they can and will tinker it to death. If you don't want to brick it, don't mess with it, use it as intended by the manufacturers, stock original.
Click to expand...
Click to collapse
I tried these two methods.
And what can i do if i can't enter in bootloader mode : it only reboot on bios (i think it is) and magldr.
I can't have a hard reset neither.
Radio : 2.15.5014
Hspl : 2.08
Fixed. Thanks for the help
Thank you all very much for the help and advice.
I did what was suggested and plugged it in while on tri colour screen, flashed the rom and phone is perfect again.
Your help is very much appreciated.
Next time I'll post in the questions section.
Related
oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?
Milan Geek said:
oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?
Click to expand...
Click to collapse
Do you have 2.08HSPL on your phone?
Hold the volume key down while you turn on your phone, then you will see the tri-color screen. and the hardspl you have.
I suggest you follow this
Make your you have flashed HSPL 2.08.
it can be found easily using search option
after that boot it to tri-color screen.
( hold volume down key and boot your phone)
Sync your phone with pc using active sync
then down there on your phone screen will say USB
now find
"Task29 provided by doloop"
in the forum.
use that to flash everything from your phone.
after that it will automatically boot into white htc logo screen and not proceed
(due to there's nothing remaining.) just ignore it and
reset your phone while pressing volume down key to enter tri-color screen
now flash mgldr.
after that your phone will boot into mgldr
then follow the instructions on forum about nand builds
PS/If you are using XP you have to make your when usb flasher
it says wait usb...usb(connect via active sync) then uncheck "the allow usb connection" on active syncs connection settings. then proceed will rom installers
hope this will help.
dirn1111 said:
Make your you have flashed HSPL 2.08.
it can be found easily using search option
after that boot it to tri-color screen.
( hold volume down key and boot your phone)
Sync your phone with pc using active sync
then down there on your phone screen will say USB
now find
"Task29 provided by doloop"
in the forum.
use that to flash everything from your phone.
after that it will automatically boot into white htc logo screen and not proceed
(due to there's nothing remaining.) just ignore it and
reset your phone while pressing volume down key to enter tri-color screen
now flash mgldr.
after that your phone will boot into mgldr
then follow the instructions on forum about nand builds
PS/If you are using XP you have to make your when usb flasher
it says wait usb...usb(connect via active sync) then uncheck "the allow usb connection" on active syncs connection settings. then proceed will rom installers
hope this will help.
Click to expand...
Click to collapse
thank you dear, i will try it today when i get home and i wish it will work
a3r0n1 said:
Do you have 2.08HSPL on your phone?
Hold the volume key down while you turn on your phone, then you will see the tri-color screen. and the hardspl you have.
Click to expand...
Click to collapse
i have 1.42 !!
i cannot sync with the PC, how to flash 2.08 now?
Make sure you have the right hspl and radio.
Sent from my HTC HD2 using XDA App
dirn1111 said:
Make your you have flashed HSPL 2.08.
it can be found easily using search option
after that boot it to tri-color screen.
( hold volume down key and boot your phone)
Sync your phone with pc using active sync
then down there on your phone screen will say USB
now find
"Task29 provided by doloop"
in the forum.
use that to flash everything from your phone.
after that it will automatically boot into white htc logo screen and not proceed
(due to there's nothing remaining.) just ignore it and
reset your phone while pressing volume down key to enter tri-color screen
now flash mgldr.
after that your phone will boot into mgldr
then follow the instructions on forum about nand builds
PS/If you are using XP you have to make your when usb flasher
it says wait usb...usb(connect via active sync) then uncheck "the allow usb connection" on active syncs connection settings. then proceed will rom installers
hope this will help.
Click to expand...
Click to collapse
the problem that i have hspl 1.42
now i cannot sync with the PC, how can i flash hspl 2.08?
Boy, you never read, do you!
go there:
http://forum.xda-developers.com/showthread.php?t=915839
Don't panic, take it easy...
MAGLDR requirements:
HSPL 2.08
RADIO that supports 576MB RAM
Milan Geek, I know I am going blind, but seriously?
YOU DON'T NEED SUCH BIG FONTS
This is what you need to do:
Unplug battery to turn device off
Put battery back in to device
Hold the Volume down button, do not let go
Press and release the power button to turn on the device
when you see the RED/GREEN/BLUE screen, plug in your USB cable to phone and computer
Run HSPL3 and update to HSPL 2.08
When done, the phone will Reboot, when screen turns off, press and hold the Volume Down button, if you don't, you will have to remove battery, put it back, hold the volume button, then turn on the device again.
when you see the RED/GREEN/BLUE screen again, make sure USB cable is connected to phone and computer install RADIO 2.15.50.14
Now MAGLDR will work.
If these instructions do not work,
MAIL IT TO ME, AND I WILL CLICK ON THANK YOU BUTTON
The phone is too complicated, I will find it a nice home.
Doesn't Work
nimbooz said:
Doesn't Work
Click to expand...
Click to collapse
What doesn't work? If OP just takes his time to read and understand all wat d above posters have posted, then he'll surely successfully get android on his device...The steps above have been used by thousands over and over again WITHOUT fail!!!...
Same problem. I have reinstalled around 20 times following steps you say and still stucks in white screen.
sanroman said:
Same problem. I have reinstalled around 20 times following steps you say and still stucks in white screen.
Click to expand...
Click to collapse
It's a simple process. If you are getting stuck at white screen the chances are you are not doing one of the first 2 steps as below.
FIRST: You have to install 2.08.HSPL (no other HSPL version and not an spl ending in .0000). Check in bootloader that you have 2.08.hspl NOT 2.08.0000.
SECOND: You have to install a 2.xx.50.xx radio (it has to be a .50 radio and not a .51 radio). Use 2.08.50.xx or higher .50 radio.
THIRD: Install magldr from bootloader by running the romupdateutility file.
I know. Please Believe I have 2.08.HSPL and 2.15.50.15 Radio installed several times without errors but same result.
Could be a HW problem? any other solution?
sanroman said:
I know. Please Believe I have 2.08.HSPL and 2.15.50.15 Radio installed several times without errors but same result.
Could be a HW problem? any other solution?
Click to expand...
Click to collapse
Have you tried going all the way back to stock winmo rom and starting the whole process again?
I know. Please Believe I have 2.08.HSPL and 2.15.50.15 Radio installed several times without errors but same result.
Could be a HW problem? any other solution?
sanroman said:
I know. Please Believe I have 2.08.HSPL and 2.15.50.15 Radio installed several times without errors but same result.
Could be a HW problem? any other solution?
Click to expand...
Click to collapse
You posted this above in your previous post already. I was now asking if you have tried going all the way back to the stock winmo rom, ie to return the phone to its original state and then start again from the beginning?
nimbooz said:
Doesn't Work
Click to expand...
Click to collapse
I had the same problem and it worked.....just follow the steps the guys described below and u will succes :-D
LiFE1688 said:
MAGLDR requirements:
HSPL 2.08
RADIO that supports 576MB RAM
Milan Geek, I know I am going blind, but seriously?
YOU DON'T NEED SUCH BIG FONTS
This is what you need to do:
Unplug battery to turn device off
Put battery back in to device
Hold the Volume down button, do not let go
Press and release the power button to turn on the device
when you see the RED/GREEN/BLUE screen, plug in your USB cable to phone and computer
Run HSPL3 and update to HSPL 2.08
When done, the phone will Reboot, when screen turns off, press and hold the Volume Down button, if you don't, you will have to remove battery, put it back, hold the volume button, then turn on the device again.
when you see the RED/GREEN/BLUE screen again, make sure USB cable is connected to phone and computer install RADIO 2.15.50.14
Now MAGLDR will work.
If these instructions do not work,
MAIL IT TO ME, AND I WILL CLICK ON THANK YOU BUTTON
The phone is too complicated, I will find it a nice home.
Click to expand...
Click to collapse
Had similar problem with MAGLDR, had no idea what to do. Found this forum and these instructions. Took some fiddling but finally got it working. THANX SO MUCH!!!
same problem doesnt work
Warning absolute noob here.
My HD2 leo froze in bootloader after using HD2Android NAND Toolkit.
Screen reads:
PB81120 SS-B3
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Computer won't recognize the device anymore.
Next steps to take would be EXTREMELY appreciated.
Thanks!
trying to "flash" stock ROM
I promise I read through the threads before I posted, but you knw how your heart races and U cant think, let alone pick up new terms? welcome to my world...
Anywy, bought a 4GB Micro SD to try to flash [I don't know exactly what that means] my stock ROM again. I'll start with saving stock ROM I downloaded to the SD and plug the battery back into HD2 with the new SD loaded.... Is that flashing?
Thanks to anyone that can help!
back up but would love some trouble shooting
to see what I did wrong and get Android on here. Thanks for an help and all the threads that're out there
To get Android back on do this:
1) download this file http://cotulla.pp.ru/leo/Android/DFT_LEO_MAGLDR113_DAF.rar
2) turn the phone onto that bootloader, then run the RUU file from the download, it should flash magldr.
3) once magldr boots you can flash the Android ROM of your choice from this list
http://forum.xda-developers.com/forumdisplay.php?f=928
You may have to flash a clockworkmod recovery, in the ROM thread it may link you to the right one to flash using the USB flasher mode in magldr.
Thanks!
I'll try that and follow up here for others
I have the same problem exactly.
and the ruu you give told me ERROR (260) : CONNECTION
What can i do?
No one here can solve this problem?
No one here can solve this problem?
7AND said:
Warning absolute noob here.
My HD2 leo froze in bootloader after using HD2Android NAND Toolkit.
Screen reads:
PB81120 SS-B3
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Computer won't recognize the device anymore.
Next steps to take would be EXTREMELY appreciated.
Thanks!
Click to expand...
Click to collapse
Maybe you don't install your ActiveSync or WMDC v6.1 correctly.
Your phone still working, because enter to bootloader but just no rom in side or error rom so it don't start up.
Please try to uninstall your activeSync or WMDC and restart your PC. Restart your PC and install ActiveSync or WMDC again.
I hope it working.
Wishes,
Not working, any other solution
picheth said:
Maybe you don't install your ActiveSync or WMDC v6.1 correctly.
Your phone still working, because enter to bootloader but just no rom in side or error rom so it don't start up.
Please try to uninstall your activeSync or WMDC and restart your PC. Restart your PC and install ActiveSync or WMDC again.
I hope it working.
Wishes,
Click to expand...
Click to collapse
Not working, any other solution
have you tried flashing a rom via the sd card download the rom, extract the stock rom find the file that ends in .nbh and rename it to LEOIMG.nbh put it in ur phone, turn phone on holding volume down until u get a grey screen and it will tell you what to press to flash.
are your volume buttons stuck is it booting straight to bootloader? if so you could have a problem
Nothing happened.
Demon_man said:
have you tried flashing a rom via the sd card download the rom, extract the stock rom find the file that ends in .nbh and rename it to LEOIMG.nbh put it in ur phone, turn phone on holding volume down until u get a grey screen and it will tell you what to press to flash.
are your volume buttons stuck is it booting straight to bootloader? if so you could have a problem
Click to expand...
Click to collapse
nothing happened. just stopped in the three color screen, Any other solution?
Any one can solve this problem.
Any one can solve this problem.
i've got the same problem..
Very anoying, i was curious about the HD2 Toolkit so i intstalled it and started working with it.
I used task 29 and after that i used clk repartition.
Now i'm stuck at udc_start()
I think because it wont connect usb
Only thing i can do is start into that and bootloader.
But when i'm in bootloader it wont connect to USB
WMDC is fresh so i'm out of options?
What do i need to do
puggepot said:
i've got the same problem..
Very anoying, i was curious about the HD2 Toolkit so i intstalled it and started working with it.
I used task 29 and after that i used clk repartition.
Now i'm stuck at udc_start()
I think because it wont connect usb
Only thing i can do is start into that and bootloader.
But when i'm in bootloader it wont connect to USB
WMDC is fresh so i'm out of options?
What do i need to do
Click to expand...
Click to collapse
flash stock via sd and try again.
Perhaps the Down volume button is damaged (always pressed and not released and you can not complete procedure to boot from SD) or at worst a shortcircuit board or processor that manifests similar.
I think I've the same problem, but with the UP volume button. I solved it after I uninstalled .dll's volume controller from WM65 (otherwise it beeps continuously and permanently displayed on the screen was the volume controller picture, like as I hold the volume up button continuously) and we could use in normal conditions.
Only the battery ends quickly (the phone completely stopped overnight, but with the battery inside the morning battery is dead). Otherwise in "normal use" is empty in 2-3 hours.
Have been using dual boot (wp 6.5 & Android) for 5-6 months. Android stopped working from sd card. Decided to try wp 7. Installed LEO70_ROM, got product key from Microsoft for Windows Live, downloaded and installed Zune. Everything was great. Got message to upgrade. Thought nodo or mango would be better. Now I have no phone. I tried unsuccessfully to go back to wp 6.5, to upgrade. Yes I know I screw up, yes it's my fault, but it has been fun learning new things and it will probably cost me something in the end. Here is where I'm at and what I've tried.
1)Power on w/o sd card-Get triangle w/ Software update failed. Please try again.
2)Power on w/empty formatted sd card-above for 1 sec then jumps to bootloader with: HX-B3; SPL-3.03.0000 XE; MicroP(LED) 0x05; MicroP(TOUCH) 0x40 displayed.
3)Power on w/vol down-opens bootloader. Same as #2 w/RUUNBH in upper right and PB81120 before HX-B3; Upgrade ROM code error; please try again, Serial.
Microsoft Device Manager does not recognize phone, hard reset acts same as #2 above, errors out when I try to run HSPL or custom radio. Reformatted sd card (not sure about partitions-created primary). I would appreciate any help. Thks
have you tried to flash stock WinMO 6.5 rom from SD card?
download stock rom for your HD2
extract *.nbh file from exe and copy it on SD card, naming it LEOIMG.nbh
boot while hold vol down..
if this fails, i have no other options on my mind...
if it works, it overwrites everything.. so you ought to have stock WM6.5 and then you can go flashing again
Have you tried:
1 - take the battery out for a minute
2 - power the phone on, holding down the volume down button to boot into bootloader
3 - flash a stock 6.5 ROM
If this works, then you'll need
1 - to flash a .50 radio (2.12.50 etc...)
2 - flash magldr 1.13
3 - flash the backto the future WP7 rom by XboxMod and Yuki. The LEO70 ROM is the original WP7 ROM from DFT and isn't updateable via Zune
Thanks for the info. I tried to flash 'T-Mobile_HD2_MR_Software_3.14.531.1' but I think I need an earlier version. The only one I could find was a .exe file. Do you have a link to the correct one?
Jack567 said:
Thanks for the info. I tried to flash 'T-Mobile_HD2_MR_Software_3.14.531.1' but I think I need an earlier version. The only one I could find was a .exe file. Do you have a link to the correct one?
Click to expand...
Click to collapse
if this is the right file for your HD2, then open it with WinRAR or 7-zip. Inside you'll see NBH file. Then follow what o wrote
and, make sure that this is corret rom file for your HD2.
Thanks, Yes it it the correct rom. I downloaded it from Tmobile support. Called HTC to see if there was a different rom and they said that was the only one they had available. To fix it they said I would have to replace the motherboard and flash the rom. When I try flashing the rom I get a white screen with 'Loading...' . Nothing happens then.
Jack567 said:
Thanks, Yes it it the correct rom. I downloaded it from Tmobile support. Called HTC to see if there was a different rom and they said that was the only one they had available. To fix it they said I would have to replace the motherboard and flash the rom. When I try flashing the rom I get a white screen with 'Loading...' . Nothing happens then.
Click to expand...
Click to collapse
Have you tried task29?
Use task 29 to clear everything, guide here http://forum.xda-developers.com/showthread.php?t=644781 then go to HTC official site and under support search for upgrades and download the latest rom for your phone and flash it.
Good luck.
I tried to run Task29 but I got a bunch of errors. I think it is because Device Manager does not reconize my phone. Can I copy the RUU_signed.nbh file from the extracted .exe file to the sd card and run it from the boot loader? Does the file need to be renamed? Is there another file I can run from the sd card? Sorry for all the questions.
Thanks for the ideas.
Jack567 said:
I tried to run Task29 but I got a bunch of errors. I think it is because Device Manager does not reconize my phone. Can I copy the RUU_signed.nbh file from the extracted .exe file to the sd card and run it from the boot loader? Does the file need to be renamed? Is there another file I can run from the sd card? Sorry for all the questions.
Thanks for the ideas.
Click to expand...
Click to collapse
press volume down and power botton to go to the multi color screen then it sould pop usb if so:
Try this http://www.youtube.com/watch?v=nrmlqrfCvas
With the phone connected to the computer and power on with volume held down my bootolader reads:
RUUNBH
PB81120 HX-B3
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Upgrade ROM code error
Please try again
USB
I formated my 16gb sd card, coppied and renamed file to sd card and rebooted. Phone display has white screen with 'Loading...' Goes no futher. Any other Ideas.
Thanks for your help.
Jack567 said:
With the phone connected to the computer and power on with volume held down my bootolader reads:
RUUNBH
PB81120 HX-B3
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Upgrade ROM code error
Please try again
USB
I formated my 16gb sd card, coppied and renamed file to sd card and rebooted. Phone display has white screen with 'Loading...' Goes no futher. Any other Ideas.
Thanks for your help.
Click to expand...
Click to collapse
Are you sure you have the correct rom?
In case it doesn’t have Windows Mobile installed or you can’t get ActiveSync to recognize it, put it into bootloader mode: A.Power off your HTC HD2.
B.Press the Volume-Down button on your phone, keep it pressed and press the Power button.
C.Keep both the buttons pressed until you see the red, green, blue and white bootloader screen and then release both buttons.
2.Now connect your phone to your PC via USB. If this is the first time you’re connecting your phone to the PC in bootloader mode, wait for the drivers to be installed automatically. The term ‘Serial’ in the white area of the screen should now change to ‘USB’.
Jack567 said:
With the phone connected to the computer and power on with volume held down my bootolader reads:
RUUNBH
PB81120 HX-B3
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Upgrade ROM code error
Please try again
USB
I formated my 16gb sd card, coppied and renamed file to sd card and rebooted. Phone display has white screen with 'Loading...' Goes no futher. Any other Ideas.
Thanks for your help.
Click to expand...
Click to collapse
huh, i fear it's bricked. Sorry..
I would like to thank both of you for your input. Yes, that is how I put it into the bootloader. I also think the phone is bricked. I have read where you can have your phone unbricked. What do you think about sending it to someone to have it done?
Thanks again for your comments.
Jack567 said:
I would like to thank both of you for your input. Yes, that is how I put it into the bootloader. I also think the phone is bricked. I have read where you can have your phone unbricked. What do you think about sending it to someone to have it done?
Thanks again for your comments.
Click to expand...
Click to collapse
anyway try this thread http://forum.xda-developers.com/showthread.php?t=614630
or this one http://forum.xda-developers.com/showthread.php?t=1247494
just a thought, have you tried putting HSPL4 on it? http://forum.xda-developers.com/showthread.php?t=611433&post#3
Thanks for thanking me Jack567, but did it work?
I found a local person that is going to try to get my phone running. If he can't I will try what you suggest. Hope I can be back soon. It's geeat to be learning new things. Technology is great and thanks to everyone that helps the noobee's like me. Hope I can help in the future. You can't learn if you don't make mistakes.
ITS NOT BRICKED I CAN BET ON THIS
Even I had the same problem ,I downloaded the official t-mobile update exe, but since I have been using HTC phones rite from Imate jam to kjam to jasjam to diamond to topaz till Leo so I found easily how to go back to 6.5 and also done for few local people, what I did is
1 Extract the tmobile update exe (see for the version which has ver. 3.03.0000 , u can find it on www.shippedroms.com or google it ) then using winrar extrect its content on your pc and rename the file RUU_Signed.nbh to leoimg.nbh
2 copied this file to my storage card and (fast use I keep a 2gb sd card and formatted &place the leoimg.nbh file to root of sd card so it looks like only 1file in storage card &no folders or anything)
3 turn off the device put the sd card & keep pressing volume down button and press power button to turn it on this will take u to 3 colored screen for a few second and then who loading on while screen if u have a proper matching leoimg on sd card then it will show u the contents i.e.
Radio v2
Splash
Bootloader
configdata
Os
And a few more things
now press the power button once and u can see the progress bar may be it mite restart ur phone but don't thing it screwed it will resume the update process & u will be back to ur stock rom
1 important point for u is that download the rom version 3.03 as it seems to me that u already have a stock spl and if u put un compatable rom then it won't move ahead from loading
Hope it helps u
So i was trying to put android with easy android and it seemed like it worked, it said we hacked it at the end. Now the phone doesnt boot up. I even tried hard resetting any help? Do i need to flash a radio? If so how and which radio?
Full filename of anything you flashed plus tmous or regular? What does "wont boot up" mean?
Details details details.
Im tmobile US. Theres an application that does an automated process. It's called Easy Android. I dont have the link for the post but it's hear on xda. When the phone boots up it just shows the T-mobile logo.
Please tell me if you need more info.
oh right, well in taht case its almost certainly either the wrong hspl or the wrong radio.
Magldr wont start unless BOTH spl is 2.08.hspl and radio is 2.07.50 or higher , but since you have a tmous the radio must be OK, so it must be the spl
enter bootloader (phone off, hold hold keep holding voldown, tap and release power, hold voldown till tri colour screen appears) what does spl line say?
Hey
Its 2.08 HSPL
BTW i appreciate the help
in that case i'd be heading back to a stock rom, get it back to as-new and start over.
Grab either the 2.13 or 3.14 TMOUS roms and flash via sd card. that will put it back to as new, then apply 2.08.hspl - magldr - cwm - rom.(get the toolkit)
I wont have a problem finding the rom, but i just need to know how do you flash the rom, do you just enter bootloader and it auto installs?
Thanks
get the phone into bootloader mode, and make sure the computer detects the phone before you start the flashing process (i.e. running the RUU).
If the rom comes in an exe file, rename it and make the file extension .zip
Then go into the .zip file and remove the file which has the file extension .nbh
Rename this file to LEOIMG.nbh
Put this file at the root of a 4Gb or smaller sd card
Put the card into your phone and boot into bootloader (hold vol down button while booting)
Should find and flash the rom all by its self, might ask you to press a certain button to confirm, been a long time, I can't remember for sure if you have to press a confirmation button
Wait for it top finish
Make sure you have 50% or greater battery before you flash
MAKE SURE you have the correct stock rom for your phone. There are different stock roms for different HD2's depending on what model HD2 you have. Flash the wrong one you could be screwed for good
Okay, running RUU while in bootloader worked perfect.
Got the ruu straight from tmobile.
Windows 7 auto installed bootloader drivers for me.
Hi,
I want to instal WP7 on my HTC HD2.
In the tutorial i use i should use the Rom update utility to get MAGLDR on my phone.
When i try to use this utility i don't get further than 0% and after some time i get a error (error 626)
What i did is:
- I reseted my HTC HD2.
- I started the Rom update utility. It says that i need a update from 1.66.404.1 to 2.00.000.0.
- So when i start this it will restart my phone and show me a progres bar.
This will stay on 0% and after 10 minutes the utility gives me a message that says:
You connection is lost(error 626). Than i need to "recover" my phone by taking the battery out and put in in again.
When i do this it wel restart my phone with the WM6.5 so nothing happend.
I tryed the following things:
- A different usb cable and usb port.
- redownload the Rom Update Utility from this site.
- Hard reset my phone.
Nothing happend a still geth the same error.
Does someone know how to fix this?
Or is there a defferent way to install WP7 on my HTC HD2.
Thanks,
Maarten
read tutorial from my signature
I will try that thanks.
I finished step 0.5 and 1.
But when I am at the line "When phone boot in MAGLDR use:"
I get stuck.
The MAGLDR is installed but when the phone restart i get stuck on the white HTC screen.
Any clou what i should do next?
if not boot, press and hold power button to start magldr....
I tryed it but it wont do anything else than go to the white boot sreen with the Green HTC logo.
I tryed to press the power button for a long time and while he is booting.
Butt notting more than te boot screen shows.
The only way to start the phone again is to remove the battery.
I can get in the "red-green-blue-white screen"
I already tryed to reinstall the magldr. But no luck.
And what do you meen with "in not boot"?
The only thing it does do is boot to this logo and that's it. So its always booting when i turn it on...
"if not boot to magldr"
which HSPL you have installed on device?
try install WM6.5 first then install magldr....
first time when phone boot after magldr flashed, must boot to magldr automatically
I have HSPL2.08
It doesn't start the magldr automatically.
Even if i hold the power button. It just starting with a white boot screen with HTC logo.
Don't know how to install wm6.5 again.
Please help. I would like to use my phone tomorow again.
Edit:
Maybe it's bricked...
boot to threecolor screen and flash WM6.5
Ok I flash back to WM6.5
What to do now?
Follow the instructions again i asume.
Anyway many thanks for your help!!!
yes, after flash, install magldr and continue...
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
you cant flash WP7 without magldr menu (setting options and enable USB flasher in magldr)...
yes this magldr is ok...
http://forum.xda-developers.com/showthread.php?t=893618
to be sure, which version of HD2 you have?
also check data in bootloader screen (threecolor)
Data in bootloader screen:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Version:
I know i don't have the t-mobile version.
HTC HD2 T8585
MasterMaarten said:
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
Click to expand...
Click to collapse
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
hjhjhj said:
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
Click to expand...
Click to collapse
I used the manual from dxdy:
STEP 0.5 - from same beginning, WP7 never or not installed on phone
- If needed (if Android NAND installed, or if any error during flash
process, erase NAND with Task29). Flashing WM6.5 not needed.
- if you have SIM locked phone and want unlock with code, you can this only in WM6.5
- insert formatted microSD card to FAT32 in phone
- flash radio if you want (if flash version available) or use radio upgrade during ROM flashing (put radio file
part00.bin in data.zip file before ROM flash)
STEP 1. - when HSPL and/or MAGLDR not installed
- Flash HSPL 2.08 if needed (put device in bootloader before Flash:
press and hold Volume down + Power button)
- Flash MAGLDR 1.13 (put device in bootloader before Flash:
press and hold Volume down + Power button)
Click to expand...
Click to collapse
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
MasterMaarten said:
I used the manual from dxdy:
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
Click to expand...
Click to collapse
you should do task29 whether you have android or not....between flashes even if wp7. task29 cleans out the memory area where the OS will reside.
as for the radio...radio thread for the TMOUS radio is here:
http://forum.xda-developers.com/showthread.php?t=1111613
more than likely you shouldn't have to flash a radio, but it won't hurt. only have to do it once.
in order to use the rom flash utility...you have to go into magdlr main screen...scroll down to and select 10. Services, then select 5. CleanMBR, and then 4. Uselast24NAND. Finally, back at the main set of options select 5. USB Flash.
Then you kick off your DWI.exe in admin mode.